Haws 1109FR User Manual

INSTALLATION, OPERATION

&

MAINTENANCE INSTRUCTIONS

1455 Kleppe Lane Sparks, NV 89431-6467 [phone] Fax [phone]

E-mail: [e-mail]  website: www.hawsco.com

NOTE TO INSTALLER: Please leave this information with the Maintenance Department.

HAWS® warrants that all of its products are guaranteed against defective material
or poor workmanship for a period of one year from date of shipment. HAWS
liability under this warranty shall be discharged by furnishing without charge F.O.B.
HAWS Factory any goods, or part thereof, which shall appear to the Company upon
inspection to be of defective material or not of first class workmanship, provided
that claim is made in writing to company within a reasonable period after receipt of
the product. Where claims for defects are made, the defective part or parts shall be
delivered to the Company, prepaid, for inspection. HAWS will not be liable for the
cost of repairs, alterations or replacements, or for any expense connected therewith
made by the owner or his agents, except upon written authority from HAWS,
Sparks, Nevada. HAWS will not be liable for any damages caused by defective
materials or poor workmanship, except for replacements, as provided above. Buyer
agrees that Haws has made no other warranties either expressed or implied in
addition to those above stated, except that of title with respect to any of the
products or equipment sold hereunder and that HAWS shall not be liable for
general, special, or consequential damages claimed to arise under the contract of
sale. The drinking fountain manufactured by HAWS is warranted to function if
installation and maintenance instructions provided are adhered to. The units also
must be used for the purpose for which they were intended.

NO OTHER WARRANTIES EXPRESSED OR IMPLIED ARE AUTHORIZED,
PROVIDED OR GIVEN BY HAWS.

SHOULD YOU EXPERIENCE DIFFICULTY WITH THE INSTALLATION OF THIS
MODEL PLEASE CALL:

TECHNICAL SUPPORT: 1-800-766-5612

FOR CUSTOMER SERVICE: 1-888-640-4297

Model 1109FR/1109FRBP

Drinking Fountain

LIMITED WARRANTY

No. 2076626(11)

04/10 Model 1109FR/1109FRBP Page 1 of 4

RECOMMENDED TOOLS: Hack saw, pipe joint sealant, screwdriver, level, 12" adjustable
wrench, 10" pipe wrench, 5/64“ hex key wrench, 9/16”, 1/2", 7/16” socket wrench or open
end wrench.

LOCATION OF UNIT: The Model 1109FR/1109FRBP Drinking Fountain is a wheelchair
accessible drinking water facility. The height dimensions shown, meet current ADA
requirements. When installing this unit, local, state or federal codes should be adhered to.
If height other than shown is required, then dimensions must be adjusted accordingly.

SUPPLY LINE: The minimum recommended line size is 1/2“IPS with 30-90 psi (2-6 ATM)
flowing pressure. Where sediment or mineral content is a problem, an inlet filter is
recommended.

PLUMBING CONNECTIONS: Waste outlet is 1-1/4” IPS (located on 6521FR Valve box).

MAINTENANCE: Periodically clean the strainer. Refer to 6521FR Valve Operation and

Maintenance Sheet for more information.

TROUBLESHOOTING

1. Insufficient bubbler flow. 1a. Check that inlet screwdriver stop valve

b. Verify minimum 30psi flowing supply

c. Adjust valve to increase flow. Use

PROBLEM

REPAIR CHECKLIST

is wide open. (Customer supplied).
Turn counterclockwise.

pressure.

front adjust screw see 6521FR Valve
Manual.

General Notes:

Before tightening nut and ferrule assembly, push tubing into fitting until it bottoms out
to ensure correct engagement with O-Ring.

For more information about Haws products, see our website: www.hawsco.com

© 2010 Haws® Corporation – All Rights Reserved
HAWS

®

and other trademarks used in these materials are the exclusive property of Haws Corporation.

04/10 Model 1109FR/1109FRBP Page 2 of 4