Haws 1011HPSMS, 1011MS Installation, Operation And Maintanance
Model 1011HPSMS/ 1011MS
Drinking Fountain
INSTALLATION, OPERATION
&
MAINTENANCE INSTRUCTIONS
No. 2076519(11)
LIMITED WARRANTY
warrants that this specific product is guaranteed against defective material
HAWS Factory any goods, or part thereof, which shall appear to the Company
upon inspection to be of defective material or not of first class workmanship,
riting to Haws within a reasonable period after
receipt of the product. Where claims for defects are made, the defective part or
parts shall be delivered to the Company, prepaid, for inspection. HAWS will not be
or replacements, or for any expense
connected therewith made by the owner or his agents, except upon written
authority from HAWS, Sparks, Nevada. HAWS will not be liable for any damages
provided above. Buyer agrees that HAWS shall not be liable for general, special,
or consequential damages claimed to arise under the contract of sale. The
drinking fountain manufactured by HAWS is warranted to function if installation
ance instructions provided are adhered to. The units also must be
NO OTHER WARRANTIES EXPRESSED OR IMPLIED ARE AUTHORIZED,
NOTE TO INSTALLER: Please leave this information with the Maintenance Departm ent.
SHOULD YOU EXPERIENCE DIFFICULTY WITH THE INSTALLATION OF THIS
1455 Kleppe Lane Sparks, NV 89431-6467 (775) 359-4712 Fax (775) 359-7424
E-mail: haws@hawsco.com website: www.hawsco.com
HAWS
or poor workmanship for a period of one year from date of shipment. HAWS
liability under this warranty shall be discharged by furnishing without charge F.O.B.
provided that claim is made in w
liable for the cost of repairs, alterations
caused by defective materials or poor workmanship, except for replacements, as
and mainten
used for the purpose for which they were intended.
PROVIDED OR GIVEN BY HAWS.
MODEL PLEASE CALL:
TECHNICAL SUPPORT: 1-800-766-5612
FOR CUSTOMER SERVICE: 1-888-640-4297
03/17 Model 1011HPSMS/1011MS Page 1 of 4
TROUBLESHOOTING
PROBLEM
REPAIR CHECKLIST
supplied) is wide open.
pressure.
Manual.
O.D.
1/4”
±.005”
11/16”
3/8”
±.005”
3/4”
1/2”
±.005”
7/8”
RECOMMENDED TOOLS: Hack saw, pipe joint sealant, screwdriver, level, 12" adjustable
wrench, 10" pipe wrench, 5/32” hex key wrench, 9/16”, 1/2", 7/16” socket wrench or open
end wrench.
LOCATION OF UNIT: When installing Model 1011HPSMS/1011MS Drinking Fountain is a
wheelchair accessible drinking water facility. The height dimensions shown, meet current
ADA requirements. When installing this unit, local, state or federal codes should be adhered
to. If height other than shown is required, then dimensions must be adjusted accordingly.
SUPPLY LINE: The minimum recommended line size is 1/2“IPS with 30-90 psi (2-6 ATM)
flowing pressure. Where sediment or mineral content is a problem, an inlet filter is
recommended.
PLUMBING CONNECTIONS: Inlet is 3/8” O.D. push-in type fitting. Waste outlet is 1-1/4”
O.D. tube.
MAINTENANCE: Periodically clean the strainer. Refer to 5874 Series Valve Manual for
more information.
1. Insufficient bubbler flow. 1a. Check that inlet screwdriver stop valve (not
b. Verify minimum 30 psi flowing supply
c. Clean strainer. See 5874 Series Valve
d. Adjust valve to increase flow. Use front adjust
screw or see 5874 Series Valve manual.
GENERAL NOTES:
1. For all plastic push-in type fitting connections, only connect NSF-61 copper
or plastic tubing. Stainless steel or glass tubing is not recommended. The
following assembly instructions must be followed to ensure a watertight
connection:
a. Cut tubing square and clean.
b. Mark from end of tube the length of insertion (See table below).
c. Push tube into the fitting until it bottoms out.
d. To remove, depress collet and pull tubing out.
Tube Sizes
Tolerance
Insertion Depth
For more information about Haws products, see our website: www.hawsco.com
© 2017 Haws® Corporation – All Rights Reserved
HAWS
03/17 Model 1011HPSMS/1011MS Page 2 of 4
®
and other trademarks used in these materials are the exclusive property of Haws Corporation.
Loading...