Hawking AR710 User Manual

AR710

Easily Network and Share your
ADSL connection

• Compliant with IEEE 802.3 over UTP
(10Base-T)

• Friendly Configuration and Management
Software

• Supports ADSL always-on

• Software Upgradeable

• Supports third party PPP over Ethernet

(PPPoE) clients.

• DSL downstream data rates up to 8 Mbps
(125 faster than standard 56K modem)

• Free Tech Support

Get Connected With Hawking

This Hawking AR710 10Base-T ADSL Router with
Modem is the ideal solution for users looking for
high-speed data access across regular phone lines.
Easily connect and share your ADSL connection with
multiple users. By placing the ADSL signal above
the frequency of the voice signal, ADSL service is
able to coexist on the same line with your telephone
service. The Hawking ADSL series provide ANSI
T1.413 issue 2, ITU-T G.hs, G.dmt and G.lite,
allowing high-speed connections over a single
twisted pair and ensuring widespread interoperability
with service providers' ADSL systems. The AR710
provides an always-on connection to your phone
company’s central office through the existing phone
line and you can also make your voice calls
simultaneously. Hawking’s AR710 ADSL Router with
Modem can easily be connected to your PC or LAN
through the 10Base-T Ethernet Interface. The
Firmware is fully upgradeable for new features and
updates. The AR710 employs ATM (Asynchronous
Transfer Mode) framing for fast transmission over
high-speed networks.

Package Contents:

• One ADSL Router w/ Modem

• One standard RJ-11 cable

• One 10Base-T RJ-45 cable

• One 9V DC Adaptor

• One 9-pin 25/9-pin RS-232 cable

• Easy to follow owner's manual

Systems Requirement:

• Pentium compatible processor 133MHz
and above

• Windows 95/98/ME/2000/XP/NT4.0, Mac,
Unix or Linux

• 10Base-T Networking Interface card

Ready, Connect & Go!

Connect to phone jack
To PC’s NIC

To PC serial port

Switch/Hub

It's easy to install, it's easy to use! Everyone can
do it.

Step1 Connect to Computer

Connect the Hawking’s ADSL Router with Modem
into your computer’s NIC or Switch using the RJ­45 cable. (included)

Step2 Connect to your phone line

Connect your 10Base-T ADSL modem to your
phone line jack using a standard phone cable (RJ­11 cable included).

Step3 Setup

Connect the Hawking’s ADSL Bridge to a console
through the serial port using RS -232 cable
included to setup the modem. Then setup network
according to your operating system.
That’s it. It’s that easy.

Application Diagram

With RJ-11 cable

for modem setup
RS-232 cable

(included)

Features Benefits

Up to 8 Mbps
downstream / Up to
640 Kbps upstream
data rate
ATM (Asynchronous
Transfer Mode)
Framing

LED 1 - Power = on or off

Easy to setup Friendly GUI configuration

125Times faster than
standard 56K modems

Packets are divided into small
fixed sizes for rapid
transmission over high-speed
networks

1 – ADSL = Status
1 – PC = Ethernet Link status
1 – RX = Receiving data
1 – TX = Transmitting data

and management software

Ordering Information:

AR710 10BT 8Mbps ADSL Router w/ Modem
AM100U USB 8M bps ADSL Modem
PN9239 4-Port DSL/Cable Firewall Router w/
10/100 WAN Port

Hawking Technologies, INC.

6A Faraday, Irvine, California, USA
Sales: [phone], [phone]

Fax: [phone]
Email: [e-mail]
Tech Support: [phone]
Email: [e-mail]
Web Site: www.hawkingtech.com

Copyright  Hawking Technologies, Inc. 2002. All rights
reserved. All trademarks herein are the property of their
respective owners. Product specification subjects to change

without notice

Specification:

Host Interface: 10Base-T Ethernet through RJ-45

ADSL: RJ-11 jack
Console: RS-232
Data Connection

- Downstream – Up to 8 Mbps

- Upstream – Up to 640 Kbps

- Rate – Adaptive in 32Kbps steps

Compliance

Standard Compliance ANSI T1.413 issue2
ITU-T G.992.1(Full rate DMT)
ITU-T G.992.2(Lite DMT)
ITU-T G.994.1(Multimode)
RFC 1483 BPDU(Bridge Ethernet over ATM PVC,
LLC/SNAP)
RFC 1483 RPDU(Routed IP over ATM PVC,
LLC/SNAP)
RFC 1577(Classic IP over ATM, MTU=1500)
RFC 2364(PPP over ATM)
ATM supports AAL5, AAL3/4 and AAL0
ATM Traffic shaping supports CBR and UBR
ATM Forum UNI 3.0, 3.1 and 4.0 signaling
ATM Forum ILMI 4.0
ATM Forum LANE 1.0 client, MTU=1516, over
SVC only
Transparent Bridging features conformance to
IEEE 802.1d and supports spanning tree
protocol and bridge filters
TCP/IP with RIP version 1(RFC 1058) and
version 2(RFC 1723) compatible
ARP(RFC 1293, supports only one single subnet)
BOOTP(RFC 2131, RFC 2132)
SNMP version 1(RFC 1155, RFC 1157, RFC 1213)
TELNET server(RFC 854, 855, 857, 858)
NAT server
TFTP revision 2(RFC 1350)

PPP (Point-to-Point Protocol) support

OAM F4 and F5 segment end-to-end loopback are
supported(F4 on all VPIs, F5 on VIP 0 only)
DHCP(RFC 2131, RFC 2132) server and client
PAP/CHAP user Authentication with PPP
PPTP tunneling

Dimensions:

5.9” x 5.31” x 1.38” (150mm x 135mm x 35mm)
(L x W x H)
Environment:
Temperature:
Operating: 0° – 40° C
Storage: -20° - 60° C
Humidity: 5% – 95% RH Non-condensing

Casing Material: Plastic
Weight: 300g
EMI: FCC Class B & CE