HAWK ENTERPRISES HP1517-180TEXHD MERLIN, HP1520-180TEXHD MERLIN, 2014 TigerHawk, 2814 TigerHawk, G2 Raptor User Manual

HAWK Merlin TEXHD

HAWK

ENTERPRISES

Severe Duty WD Industrial Floor Machine

Stripping, Scrubbing, Resurfacing

TM

Operation Care Service

(4) 20#

Weights

Included

HAWK ENTERPRISES 2902 Park Six Court, Elkhart, IN 46514 [phone] [phone]

www.hawkenterprises.com

Service Information .................................................................................................2

Machine Specications ............................................................................................3

Features ....................................................................................................................3

Important Safety Instructions ...................................................................................4

Grounding Instructions ........................................................................................5-6

Operations ...............................................................................................................7

Guidelines For Operations .......................................................................................7

Controls ...............................................................................................................7

Adjustments.........................................................................................................8

Cord Storage .......................................................................................................8

Clean Up And Storage .............................................................................................8

Merlin Assemblies .............................................................................................9-14

Optional Accessories ..............................................................................................15

Limited Warranty ....................................................................................Back Cover

SERVICE INFORMATION

To obtain consistent performance over the life of your equipment, read though these

instructions and save them for future reference. If you require service, contact the

dealer from which the machine was purchased or an authorized service station.

Always refer to your limited Warranty for complete service information.

The model, type, and serial number are indicated on the data plate on the side of the

handle. From prompt and complete service, refer to these numbers when

inquiring about service.

Write the model and serial number of your

SERIAL NO.

VOLTS
MOTOR

PHASE
AMPS

MODEL

HZ
H.P.

unit in the space provided. Refer to the

SERIAL #

data plate on unit.

MODEL #

Retain this owners manual for future reference.

2

HAWK Merlin TEXHD

Severe Duty WD Industrial Floor Machine

TM

Specificaons

Model # HP1517-180TEXHD HP1520-180TEXHD
MERLIN MERLIN

Part # F0040-17 -1.5TE F0040-20-1.5TE

Machine Size 17 inch 20 inch

Pad Size 16 inch 19 inch

Pad Speed 165 RPM 165 RPM

Amp Draw 7.9 8.5

All Sizes

Motor 1.5 HP, 180 frame, TEFC dual capacitor AC motor

Drive System Triple-Planetary XHD 11:1 helical cut industrial gears

Power 115-230V, 60 Hz power

Power Cord 50 . 2-part, 12-3 SJTOW industrial power cord

dB Rang 66 dB - Meets GS42 standard

Features

• Twin (dual) capacitor 180 frame TEFC

(Totally Enclosed Fan-Cooled) motor
keeps out dirt and dust for longer motor
life.

• Extra heavy duty spring steel cord

strain relief with a 2-piece 12-3 power
cord

• Low current draw

• Thumb operated safety switch

• Negative pressure on/off switch

• Dual steel operating triggers for left or

right hand operation

Revolutionary Design that Utilizes......

• Floating head to insure 100% pad

contact at all times

• Low Profile

• Quick handle/Carriage Removal

• One-piece industrial powder coated

heavy duty steel handle for optimum
durability

• Welded frame for rugged, reliable

performance

• 8” Non-marking, 2X8, ball bearing

wheels

• Multiple position handle adjustment

for operator comfort and safety

• Comfort style vinyl handle grips for

ease of use

3

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic precautions should always be followed, including the following:

WARNING:

ELECTRIC SHOCK CAN CAUSE SERIOUS

INJURY OR BE FATAL. PLEASE READ THE

FOLLOWING INSTRUCTIONS ON THE USE

AND OPERATIONS OF FLOOR FINISHING

MACHINES.

• Your Merlin is equipped with a safety switch lock and power switch triggers designed
for your safety. Do not attempt to bypass or defeat the safety switch lock. Never use any
device to lock the power switch triggers in the “ON” position.

• Do not leave the Merlin plugged in. Turn off the switch and unplug the electrical cord
when not in use and before servicing or changing the brushes or pads.

• Do not allow the machine to be used as a toy. Close attention is necessary when used
near children. Do not leave the machine connected to an electrical outlet unattended.

• Use only as described in this manual. Use only manufacturer’s recommended
attachments.

• Do not use with a damaged cord or plug. If the machine is not working as it should, has
been dropped, damaged, or left outdoors, return it to a service center before using.

• Use care to keep the electrical supply cord around sharp edges or corners. Keep the cord
away from the heated surfaces.

• Connect to properly grounded (3-wire) outlet only. Refer to Grounding Instructions,
Page 5-6.

• Do not use extension cords or outlets with inadequate current carrying capacity.

• Turn off all controls before unplugging.

• Do not unplug by pulling on the cord. To unplug, grasp the plug and pull.

• Do not handle the plug or Merlin with wet hands.

• Wind the cord no tighter than is necessary to retain it during storage. Refer to Cord

Storage, Page 8.

• Use extra care when working on or near stairs.

• Do not use in conjunction with ammable or combustible liquids such as gasoline, or

use in areas where explosive vapor or dust may be present.

• Store your Merlin indoors in a cool, dry area.

• Keep your work area well lighted.

• WARNING: To avoid electrical shock, use indoor only.

4

WARNING:

RISK OF EXPLOSION. FLOOR SANDING

MACHINE CAN RESULT IN AN EXPLOSIVE

MIXTURE OF FINE DUST AND AIR. USE FLOOR

SANDING MACHINE ONLY IN A

WELL-VENTILATED AREA, FREE FROM ANY

FLAME OR MATCH

GROUNDING INSTRUCTIONS

This appliance must be grounded. If it should malfunction or break down, grounding provides a
path of least resistance for electric current to reduce the risk of electric shock. This appliance is
equipped with a cord that has an equipment-grounding conductor and grounding plug. The plug
must be plugged into an appropriate outlet that is properly installed and grounded in accordance
with all local codes and ordinances.

FOR FLOOR FINISHING MACHINES RATED LESS THAN

150 VOLTS

Improper connection of an equipment grounding conductor can result in risk of electric shock.

Check with a qualied electrician or service person if you are in doubt as to whether the outlet is
properly grounded. Do not modify the plug provided with the appliance. If it will not t the outlet,
have a proper outlet installed by a qualied electrician. This appliance is for use on a nominal 120

volt circuit and has a grounding plug that looks like the plug illustrated in Figure 1.

A temporary adapter which looks like the adapter illustrated in Figure 2 may be used to connect this
plug to a two pole receptacle, as shown, if a properly grounded outlet is not available. The temporary

adapter should be used only until a properly grounded outlet (Figure 1) can be installed by a qualied

electrician. The green colored rigid ear, lug, or the like extending from the adapter must be connected
to a permanent ground such as a properly grounded outlet box cover. Whenever the adapter is used, it
must be held in place by metal screw.

FOR FLOOR FINISHING MACHINES RATED 150-220 VOLTS:

If the machine is provided with an attachment plug cap as shown in Figure 3, it is intended for use on
a 240 volt (nominal) circuit. No adapter is available for this cap.

5

WARNING:

DO NOT USE GROUNDING

ADAPTERS ON MerlinS IN

CANADA. CHECK WITH CANADIAN CODE

FOR PROPER EQUIPMENT USAGE.

IMPROPER USE OF GROUND ADAPTORS CAN

CAUSE SERIOUS INJURY, FIRE, OR BE FATAL.

Grounding Instructions (Continued)

6

CONTROLS

TO TURN THE MACHINE ON

The operating handle must be lowered and locked to the proper operating position before switching the

machine ON. Place both hands rmly on the handle grips with your ngers around the power triggers.

Do NOT apply pressure on the triggers before the safety switch lock is disengaged.

Disengage the safety switch lock by pushing it forward with one thumb. Then, while holding the safety
switch lock in the disengaged position, squeeze the power triggers toward the handle grips and return
your thumb to the handle grip.

Push forward to disen-

gage safety switch lock.

To stop the machine, simply release the triggers. The safety switch lock will automatically return to the
engaged position.

GUIDELINES FOR OPERATION

• Your Merlin is a very sensitive, powerful unit. When in operation, it should be guided gradually and
smoothly without sudden or rough motions. You will want to practice with your machine on a smooth
surface until you have experience in operating it.

• For ease of operation, always keep the brush or pad surface level, balanced, and at on the oor at all

times.

• Always adjust the operating handle to a comfortable height at which the brush or pad surface is bal­anced before starting the machine. (See Handle Adjustment Page 4)

• Your Merlin will operate differently on various surfaces. For example, there will be much more resist­ance when the machine is used on a rough surface, than when it is used on a smooth surface. The
operator should be prepared to adjust for these differences.

• BEGIN OPERATING THE MERLIN WITH THE PAD SURFACE LEVEL, BALANCED AND
FLAT ON THE FLOOR.

• To move the machine to the right, slowly apply slight upward pressure on the handle.

• To move the machine to the left, slowly apply slight downward pressure on the handle.

• To move the machine forward or backward, keep the brush or pad at on the oor and push or pull the

machine in the desired direction.

7

ADJUSTMENTS

HANDLE ADJUSTMENT

The handle can be adjusted to any desired work position by simply pulling on the pull
pin and move the handle to the desired position. Firmly push the pull pin back into the
adjustment holes. This will lock the handle in position.

Pull Knob

CORD STORAGE

When not in use, loosely coil the power cord and hang on

the handle.

Figure 5

CLEANUP AND STORAGE

After being used, your Merlin can be wiped clean with a soft damp cloth and should be

stored in a clean, dry place.

8

9

FIGURE (1)

29

31

30

33

24

32

27

REAR

26

28

FRAME TOP VIEW

FRONT

REFERANCE

VIEW

REAR

REAR OF

MOTOR

25

REFERANCE

TOP

VIEW

10

REAR VIEW

FIGURE (2)

SAFETY

LABEL

SEE FIGURE (3) FOR ASSY INSTRUCTIONS

11

ASSEMBLE HANDLE TO CARRIAGE

INSTALLATION SEQUENCE OF WHEELS AND HANDLE ASSEMBLY

2

ASSEMBLE LEFT WHEEL ASSY

REPEAT SEQUENCE #1

1

FIGURE (3)

3

12

7

8

9

10

11

7

13

60 SHOWN FOR
REFERENCE ONLY

INC. IN KIT 59

1/18/2016

DETAIL PART MERLIN HANDLE

KIT2006 SAFETY SWITCH KIT 1

2 INC IN KIT2006 SPRING 2.0L X .025 X .026 1

3 INC IN KIT3011BLK ROLL PIN 1/8 X 1.75L 2

5 INC IN KIT3011BLK TRIGGER 14 INCH BLK 1

6 INC IN KIT2011BLK HANDLE GRIP - BLK 2

KIT1005 MAIN ON/OFF SWITCH REPLACEMENT KIT 1

9 INC IN KIT1005 FLAT WASHER ZN 5

12 INC IN KIT2005 STRAIN RELIEF ASSY 1

15 INC IN KIT1033 PIGTAIL 21" L 14-3 YELLOW 1

16 INC IN KIT3018 SPRING KNOB ASSY 1

KIT3008RED INC IN KIT3008RED SWITCH BOX COVER KIT - RED 1

19 INC IN KIT3008RED LABEL WARNING - REAR 1

21 INC IN KIT3008RED WASHER #10 EXT TOOTH LOCK 2

22 INC IN KIT1028 INHANDLE CORD 1

24 INC IN KIT1028 SCREW 10-24 X .50 1

KIT1029 MERLIN HANDLE ASSY. 1

(NOTE)

NUMBER NUMBER DESCRIPTION

1 INC IN KIT2006 SAFETY SWITCH 1

KIT3011BLK TRIGGER REPLACEMENT KIT 14 INCH 1

4 INC IN KIT3011BLK SPRING - TRIGGER 2

KIT2011BLK HANDLE GRIP KIT 1

7 INC IN KIT1005 MAIN ON/OFF SWITCH 1
8 INC IN KIT1005 WASHER INTERNAL TOOTH - LOCK 1

10 INC IN KIT1005 SWITCH INSULATION 1
11 INC IN KIT1005 FLAT WASHER 5/16 ZN 1

KIT2005 STRAIN RELIEF REPLACEMENT KIT 1

QTY.

REQ'D

13 INC IN KIT2005 NUT - APPLETON .50 1
14 INC IN KIT2005 WASHER FLAT .890 X 1.5 X .104 ZN 1

KIT1033 PIGTAIL 21" L 14-3 YELLOW & STRAIN RELIEF KIT 1

INC IN KIT1033 KIT2005 STRAIN RELIEF KIT 1

KIT3018 MERLIN SPRING KNOB ASSY 1

17 INC IN KIT3008RED SWITCH BOC COVER - RED 1
18 INC IN KIT3008RED LABEL SWITCH BOX COVER - FRONT 1

20 INC IN KIT3008RED SCREW 10-24 X .50 2

KIT1028 INHANDLE CORD KIT 1

23 INC IN KIT1028 INHANDLE LOOP CLAMP 1

25 INC IN KIT1028 GROMETT 1

26 INC IN KIT1029

(NOTE) (LESS INHANDLE CORD) KIT1028 1

MERLIN HANDLE ASSY. COMPLETE (SEE NOTE)

(LESS PIGTAIL) KIT1027YEL 1

1

14

1/18/2016

MERLIN MACHINE

NUMBER NUMBER DESCRIPTION

REQ'D

GEARBOX XHD 3 IDLER ONLY (NO FLANGE)

1

42 INC IN KIT2027 LINCH PIN W/BAIL LOCK 4

DETAIL PART

KIT2022 MOTOR FAN GUARD KIT 180F TEFC 1

1 INC IN KIT2022 GUARD 1
2 INC IN KIT2022 SCREW 2.5L X #12 SCK HD SHT MTL 4
3 INC IN KIT2022 SPACER 4

KIT1022BLK-P MOTOR 180F TEFC W/ GEARBOX & PIGTAIL INSTALLED 1

4 INC IN KIT1022BLK-P MOTOR 180F TEFC 1
5 INC IN KIT1022BLK-P PIGTAIL 1
6 INC IN KIT1022BLK-P GEARBOX XHD 3 IDLER 1

7 KIT1025
8 KIT1018

KIT2023 PULL PIN BUSHING KIT 1

9 INC IN KIT1023 PULL PIN BUSHING 2

KIT2024 MERLIN HEAD - STD UNIT BLK KIT 1
KIT2023 INC IN KIT1024 PULL PIN BUSHING KIT 1

10 INC IN KIT1024 MERLIN HEAD - STD UNIT BLK 1

KIT2015 BRUSH COVER MTG. KIT 1

11 INC IN KIT2015 SPACER BRUSH COVER 4
12 INC IN KIT2015 WASHER INTERNAL TOOTH 5/16 4
13 INC IN KIT2015 SCREW SOCKET CAP 6/16-18 X 2.0L 4

KIT3017RED BRUSH COVER / BUMPER KIT - 17 INCH 1

14 INC IN KIT3017RED BUMPER 17 INCH BLACK 1
15 INC IN KIT3017RED BRUSH COVER 17 INCH RED 1

KIT3020RED BRUSH COVER / BUMPER KIT - 20 INCH 1

14 INC IN KIT3020RED BUMPER 20 INCH BLACK 1
15 INC IN KIT3020RED BRUSH COVER 20 INCH RED 1

KIT2028 MERLIN SPRING KNOB ASSY 1

16 INC IN KIT2028 SPRING KNOB ASSY 1

17 SUB-W0016-CARBLK MERLIN CARRIAGE WDMT BLACK 1

KIT1025 WHEEL KIT - MERLIN (2 REQ'D) 2

18 INC IN KIT1025 WHEEL -- MERLIN 8 X 2 1
19 INC IN KIT1025 BLOT 1/2-13 X 4.5L GR8 ZINC 1
20 INC IN KIT1025 WASHER FLAT 5
21 INC IN KIT1025 WASHER WAVE 2
22 INC IN KIT1025 NUT 1/2-13 NYLOC 1

KIT1014 MOTOR 1.5 HP 115/50-60C W/ 3 IDLER XHD GEARBOX & SCREEN 1

23 INC IN KIT1014 KIT1021 MOTOR ONLY 2 SPEED 115V 50/60CY W/SCREEN INSTALLED 1
24 INC IN KIT1014 SCREW 10-24 X .50L THRID ROLL ZN 1

25 INC IN KIT1014 SCREEN RETAINING SPRING 2

26 INC IN KIT1014 MOTOR SCREEN 1
27 INC IN KIT1014 WASHER #10 INTERNAL LOCK ZN 1
28 INC IN KIT1014 KIT1020 (XHD) 2 SPEED GEARBOX 1

KIT3002BLK MOTOR DRIP COVER / MTG KIT 1

29 INC IN KIT3002BLK MOTOR DRIP COVER - BLACK 1
30 INC IN KIT3002BLK SPACER .500 X .625L 3
31 INC IN KIT3002BLK WASHER LOCK #10 EXT 3
32 INC IN KIT3002BLK LABEL MOTOR 1
33 INC IN KIT3002BLK SCREW 10-24 X 1.0 TT 3

KIT2026 HANDLE MTG. HDWR KIT 1

34 INC IN KIT2026 BOLT 1/2-13 X 4.5L BR8 ZN 1
35 INC IN KIT2026 WASHER FLAT ZN 2
36 INC IN KIT2026 WASHER WAVE ZN 2
37 INC IN KIT2026 NUT 1/2-13 NYLOC ZN 1

KIT2027 WEIGHT KIT (4) 20 LB. W/MTG. HDWR & LINCH PINS 1

38 INC IN KIT2027 WEIGHT 20 LBS. BLK 4
39 INC IN KIT2027 WEIGHT PIN ZN 4
40 INC IN KIT2027 WASHER LOCK 3/8 SPLIT ZN 4
41 INC IN KIT2027 BOLT 3/8-16 X 7/8L ZN 4

GEARBOX XHD 3 IDLER (FLANGE ONLY)

QTY.

1

15

Accessories for Every Application

Hawk Scrapers
(Surface Prep):

17” HP0033
20” HP0034

Diamond Pad

Driver

17” A0010DPD
20” A0011DPD

Orbitec Diamond

Driver:

17” HP0017
20” HP0020

Pad Driver:

17” A0010
20” A0011

17” A0010WTDPD (46#)
20” A0011WTDPD (64#)

Grit Brush:

17” A0008
20” A0009

Weighted Diamond

Pad Driver:

Sand Paper Driver:

17” A0014-HD
20” A00014-1HD

3” DIAMONDS 30 50 100 120 200 220 400 800 1500 1800 3000 3500 8500

Rosox Resin
Turbo Cat
Typhoon
Concrete Flex
Granite Polish
Marble Flex

X X X X X X X
X X X X
X X X X X X X X
X X X X X X X X
X X X X X X X X

X X X X X X

Dust Pickup System
HP0031-DC17-BRUTEKIT
HP0031-DC20-BRUTEKIT

LIMITED WARRANTY

Your HAWK equipment which has been manufactured, tested and inspected in accordance with carefully

specied engineering requirements, is warrantied to be free from defects in material and workmanship. This
Limited Warranty is, however, subject to the Following qualications, conditions and limitations which are set

forth to provide you and all users of the HAWK equipment with information concerning the duration, extent,
availability, and applicability of this HAWK Limited Warranty, the procedure to be taken to obtain its perform­ance, and other information concerning the HAWK Limited Warranty policy.

The HAWK ENTERPRISES Limited Warranty is extended to the original end user as follows:

Non-wear items: 3 year parts replacement and 1 year service labor warranty.

Replacement parts guaranteed for 90 days from date of installation against

defects in material and workmanship.

This Limited Warranty will not cover damage attributable to the following:
(1) Improper, unreasonable or negligent use of abuse of the equipment
(2) Abrasions or punctures of the equipment.
The start date of the Limited Warranty coverage shall be the purchase date of the original end user or six months

from the date the machine was shipped from the Factory, whichever comes rst.

PARTS OF EQUIPMENT NOT COVERED BY THE LIMITED WARRANTY

Certain parts of equipment require replacement in the ordinary use due to normal wear by reason of their char­acteristics. Normal wear items such as cords, switches, bumpers, bearings, isolators, compensators, capacitors
etc. are excluded from the Limited Warranty.

EXCEPTIONS AND EXCLUSIONS FROM THE LIMITED WARRANTY

This equipment is required to be used on electric current as indicated on the data plate. Otherwise damage,
defects, malfunctions or other failure of the equipment arising from use on electric current not as indicated are
excepted and excluded from this Limited Warranty. Defects, malfunctions, failure or damage of the equipment
caused by improper, unreasonable or neglect use or abuse while in possession of the purchaser are likewise
excluded from this warranty. If repair is done on your equipment by anyone other than those designated as

authorized to perform such work without rst having obtained factory instructions, HAWK ENTERPRISES at

its sole option, my determine that this warranty will not apply and that reimbursement for such repair will not

be made because of the failure to comply with such factory specied instructions.

PROCEDURE TO BE TAKEN TO OBTAIN PERFORMANCE OF LIMITED WARRANTY REPAIR

To secure repair of the equipment or any warranted parts under this Limited Warranty, the following procedure
should be taken. The inoperative equipment or warranted parts, together with satisfactory evidence of the pur­chase date, must be delivered, with shipping and delivery charges prepaid, to one of the following:
(1) The dealer from whom purchased;
(2) Any HAWK distributor’s service department in the United States;
(3) Any HAWK authorized service station in the United States.
If you are unable to locate any of the foregoing, you may write or otherwise communicate with HAWK
ENTERPRISES before repair service is performed by anyone else. In such event, HAWK ENTERPRISES will
provide either the location or a closely available HAWK distributor service department, or HAWK authorized
service station or other factory instructions. Upon compliance with the above procedure, all warranted defects
will be repaired, at no additional charge or costs to the customer, and the repaired product returned to the
customer, with all shipping and delivery charges pre-paid. In following the procedures set forth, PLEASE
MAKE CERTAIN to state the model, type and serial number as shown on the data plate of the equipment.

REPLACEMENT

In the event of a defect, malfunction or failure of your HAWK equipment or any warranted part to conform
with this warranty, HAWK may, at its sole option and own expense, replace the equipment or any warranted
part with another new, identical or reasonably equivalent model or part in lieu or repairing the defect. DO NOT
return any equipment or part to the factory without prior authorization.

NO REFUND OF PURCHASE PRICE

HAWK ENTERPRISES WILL NOT, as a matter of it’s Limited Warranty policy, refund the customer’s
purchase price.

LIMITED WARRANTY REGISTRATION CARD FOR YOUR EQUIPMENT AND REQUEST FOR INFORMATION

Your HAWK distributor from whom you purchased your equipment is responsible for the registration of your
Limited Warranty with the factory. Any information or questions you may have concerning your HAWK
ENTERPRISES equipment or this Limited Warranty may likewise be secured from the factory. This Limited

Warranty will give you specic legal rights, and you may also have other rights which vary from state to state.

Genuine
Commerical
Products by:

Hawk Enterprises of Elkhart

Elkhart, IN USA