Havis-Shields Interior Window Guards F2 User Manual

INSTALLATION INSTRUCTIONS WGI-F1, F2, F3, F4

INTERIOR WINDOW GUARDS

FOR 1994 – 2008 FORD WINDOW VANS

TOOLS REQUIRED:

Power Drill
1/8” Drill Bit
Phillips Screw Driver
Metric Socket set

HARDWARE:
QTY DESCRIPTION PART#

115 #10 x ½” Sheet metal screws GSM34185
30 #10 X 1 ¼” Sheet metal screws GSM33197
24 #10 Flat Washer GSM31003
15 M4 x 7mm Hex nuts GSM30200
24 ½” Nylon spacers GSM20095
2 Window Latch cover plate WGI-F1-COVER PLATE
2 T-25 Torx ¼” Hex Insert OAL Tamperproof Bit SM10260

SUBASSEMBLY:

1. Remove seats and seat belts for better access to the windows.

2. Remove plastic trim surrounding the fixed body windows. Save the plastic trim for

reinstallation.

3. Determine which guard goes to each window. NOTE: The perforated diamond shaped holes has
one side that is smoother than the other. The smoother side goes towards the inside, facing the
passenger.

DOOR WINDOW GUARDS:

1. In order for guard to fit properly on frame, you must permanently remove the upper plastic trim

on doors. The top of the lower door panel may have to be trimmed approximately ¼” to ½”.
(Note: Place guard on window frame to determine possible trimming). See section 8 – door

window guard does not have cutouts for window latches (making them inoperable).

2. With the doors open, hold the window screen up to the window/door frame. The guard

framework should fit evenly around the window frame.

3. Mark a few holes at the top of the door frame using the predrilled holes on the screen framework
as a guide. Do not mark holes for the sides or bottom yet.

4. Put on Safety goggles.

5. Remove window guards and drill holes as marked with a 1/8” drill bit.

6. Attach window screens by using #10 x ½” sheet metal screws. Now locate and mark the balance

of holes, drill and attach, starting at the top and work your way down.

7.

If vehicle has plastic upper door trim, do not reinstall.

Ratcheting Wrench
T-50 Torx Bit (for seat belts)
Plastic Cutting Tool (utility knife or tin snips)

WGI-F1-F2-F3-F4_INST_7-08

SIDE SLIDING DOOR WINDOW GUARD (F2-10):

1. A 14” long aluminum angle bracket is provided to attach to the rear vertical section of the
window frame.

2. This is necessary in order to screw on the rear vertical section of window guard.

3. Using four (4) #10 x ½” Sheet metal screws, attach angle bracket to frame through existing
bracket holes.

• The side of the bracket without holes should be flush with the inside of the window
frame.

• The window guard can now be installed as stated in section #4. See section 8 – door
window guard does not have cutouts for window latches (making them inoperable).

FIXED BODY WINDOW GUARD:

1. While holding the cage in place, drill 1/8” pilot holes for mounting screws.

2. Install using #10 x ½” sheet metal screws provided.

NOTE 1: Be careful not to drill into glass. (Use drill stop)
NOTE 2: To avoid stripping of holes, do not over tighten.
NOTE 3: Some of the trim mounting spring clips may need to be removed to allow screens to
meet the window frame easily.

PLASTIC WINDOW TRIM INSTALLATION:

1. Plastic Trim Spacing:

• Plastic trim must be spaced out ½” to accommodate window guard.

• Remove the top screws from the lower trim panels.

(These panels should still be in the van).

• Pull out the lower panel just enough to insert the ½” nylon Spacers provided with the kit.

• Screw the top of the lower trim panels back on with #10 x 1 ¼” sheet metal screws also

provided with the kit.

2. Metal Spring Clip Spacing:

• (See diagram 1 on page 4) There are metal spring clips that hold the upper trim in place.
These clips must also be spaced out using the following method.

• Using a 9MM socket, remove the spring clip and nut.

• Immediately reinstall the nuts only.

• Put two #10 washers onto the same bolt on top of the nut.

• Put spring clips on top of the washers.

NOTE: More washers can be used if needed. Make sure to leave sufficient threads for metric nut.

• Using a 7MM socket, put the M4 x 7MM nut (supplied in this kit) on the stud to the hold
spring clip and washers. Proceed to the next spring clip.

• When all the spring clips are reinstalled, the interior trim can then be reinstalled.
Everything should fit neatly.

WGI-F1-F2-F3-F4_INST_7-08