INSTALL INSTRUCTIONS
C-VS-0812-CHGR & C-VS-0812-CHGR-1
20” VEHICLE SPECIFIC LOW PROFILE CONSOLE
2006-2007 DODGE CHARGER and MAGNUM
2008 DODGE CHARGER and MAGNUM
TOOLS REQUIRED:
Ratcheting wrench
Sockets - 7/16”
Combo wrench set
HARDWARE:
ITEM# QTY DESCRIPTION PART #
1 1 8” console housing CM000672
2 1 Support bracket for stout console CM001595
3 1 12” Low profile console (housing only) C-SM-1200-H
4 1 Frame support bracket CM001593
5 1 YAW sensor cover panel CM001638
6 1 Rear floor filler panel CM001642
7a 1 Driver side wire panel - 2006 – 07 Charger CM001598-D
7b 1 Driver side trim panel - 2008 Charger CM002165
8a 1 Passenger side wire panel - 2006 – 07 Charger CM001598-P
8b 1 Passenger side trim panels - 2008 Charger CM002164
9 2 “L” bracket mounting leg C-B41
10 1 Extension floor plate CM93712
8 ¼-20 Hex nut GSM30005
8 ¼-20 x ¾” Hex bolt GSM33001
8 ¼-20 Serrated nut GSM30023
6 10-32 x ½” Phillips machine screw GSM33118
4 10-32 Keps nut GSM30028
2 #10 Flat washer GSM31003
2 Torx hardware kits C-HK-1
1 Mounting hardware kit C-HK
Screwdriver set
T-20 torx bit
#8
#7
#4 (not shown)
#1
#2
#3
#10 & #9
(not shown)
#5
#6
#9
Always!
Read all instructions before installing any Havis-Shields Equipment Corp products.
Check for obstructions (Wire, brake lines, fuel tank, etc.) before drilling any holes!
Use hardware provided with install kit
For product support, visit the Install Instructions Section of our website at
http://havis.com/Installation/Installation.html, email technicalsupport@havis.com or call
1-800-524-9900.
2
C-VS-0812-CHGR_INST_12-07
Note: Be sure OEM wiring is not
floor filler panel
20 x ¾” hex bolts
Remove OEM supplied trak.
used
(#4) to vehicle using 10/32 x ½”
and #10 x ½” phillips machine screws
and washers
(#4) to vehicle using 10/32 x ½”
tly to accommodate the console front support bracket. Bending these tabs can easily
Note: Some hardware is re-
in installation of console
View of trak removed
Attach frame support bracket
phillips machine screws,
washers, and keps nuts
Attach frame support bracket
phillips machine screws,
washers, and keps nuts
Note: Due to some slight differences on the OEM floor mount bracket, tabs with mounting hole may
need to be bent sligh
Tighten hardware
be done using pliers.
Attach support bracket for stout
console (#2) to vehicle and to frame
support bracket using OEM hardware
View of installation to this point
Place console assembly and
install extension (#10) for “L”
being crushed by mounting
brackets
bracket mounting leg on stout
console, using OEM hardware.
3
Attach “L” bracket mounting
leg (#9) to rear
(#6) using ¼-
C-VS-0812-CHGR_INST_12-07
and serrated nuts.
Attach rear floor filler panel (#6)
Attach YAW sensor cover panel
frame support bracket using #10
to vehicle using OEM hardware
(#5) to vehicle using front
driver side hardware from rear
floor filler panel (#6)
Attach driver and passenger-
side wire panels (#7 & 8) to
x ½” phillips machine screws
and washers.
View of installed C-VS-0812-CHGR
Route wiring and install emergency
controls and accessories
4
C-VS-0812-CHGR_INST_12-07
Loading...