Havis DS-PAN-110, DS-PAN-111, DS-PAN-111-1, DS-PAN-111-2, DS-PAN-112 Owner's Manual
...
DS-PAN-110 Series
Havis Rugged Mobile Docking Station
For Panasonic CF-30
& CF-31 Toughbooks
www.havis.com
1-800-524-9900
Owner’s Manual
DS-PAN-111
DS-PAN-111-1
DS-PAN-111-2
DS-PAN-112
DS-PAN-112-1
DS-PAN-112-2
DS-PAN-113
www.havis.com • 1-800-524-9900
DS-PAN-111
DS-PAN-111-1
DS-PAN-111-2
DS-PAN-112
DS-PAN-112-1
DS-PAN-112-2
DS-PAN-113
Before Beginning
(Original Instructions)
1 10
• NEVER STOW OR MOUNT THE DOCKING STATION DIRECTLY IN A VEHICLE
AIRBAG DEPLOYMENT ZONE.
• DO NOT USE COMPUTER WHILE DRIVING.
• READ ALL INSTRUCTIONS THOROUGHLY BEFORE BEGINNING INSTALLATION.
• DO NOT MATE COMPUTER TO DOCKING STATION UNLESS COMPUTER’S DOCKING
CONNECTOR ACCESS DOOR IS FULLY OPEN OR DAMAGE MAY RESULT.
Havis is pleased to provide this Owner’s Manual to aid in the proper installation
and use of the DS-PAN-110 Series Docking Station for the Panasonic CF-30
& CF-31 laptop computers.
For questions regarding the set-up of your DS-PAN-110 Series Docking Station,
please contact Havis at 1-800-524-9900 or visit www.havis.com/CF31 for
additional product support and information.
This Owner’s Manual applies to the following Product Numbers:
• FOR PROPER SYSTEM FUNCTION, THIS DOCKING STATION SHOULD BE USED ONLY WITH
PANASONIC CF-30 AND CF-31 MODEL COMPUTERS. PANASONIC CF-29 AND EARLIER
MODELS ARE NOT COMPATIBLE.
• FOR PROPER SYSTEM FUNCTION, PANASONIC RECOMMENDS USING A 120W POWER
SUPPLY (LPS-104 OPTIONAL) WITH A CF-31 HIGH POWER (2.5GHz) COMPUTER.
• FOR CF-31 MEDIUM (2.4GHz) AND LOW (2.2 GHz) POWER COMPUTERS, A 90W POWER
SUPPLY (LPS-101 OPTIONAL) IS ACCEPTABLE, HOWEVER A 120W POWER SUPPLY
(LPS-104 OPTIONAL) MAY ALSO BE USED.
Installation of Power Supply (LPS-101/LPS-104 - Optional)
1). Power off computer and ensure all cables are disconnected from computer.
2). Plug in both input and output cables (supplied with LPS-101/LPS-104)
into the Power Supply brick.
3). With the Docking Station right side up, drop (4) #6-32 screws (supplied
with LPS-101/LPS-104) through the holes in Docking Station as shown.
4). While supporting the (4) #6-32 screws, ip the Docking Station upside
down and place (1) at washer over each of the (4) #6-32 screws.
5). Place the Power Supply brick over the (4) #6-32 screws ensuring that the
screws pass through all of the bosses on the Power Supply brick and the
cables are pointing in the direction shown.
6). Place the remaining (4) at washers over each of the #6-32 screws and
hand start a #6-32 locking nut onto each of the screws.
7). Torque all (4) #6-32 locking nuts to 0.9 Nm (8.0 in-lbs) ±10% ensuring
that the #6-32 screws stayed properly aligned with the bosses of the
Power Supply brick.
8). Route the Power Supply output cable as shown and secure connector
to power input port on Docking Station. Be sure to coil and strain relieve
excess cabling.
9). Return to Installation & Cable Management Step #3 on Page 4.
NOTE: Refer to Page 1 to ensure that you have the appropriate Power Supply for your Specic computer model.
Table of Contents
Specications
Parts Included
Port Replication Capability
Installation & Cable Management
Operation - Docking
Dock Indicator LED Diagnostics
Operation - Undocking
Zip Tie/Push Pin Information
Installation of Power Supply (LPS-101/LPS-104 - Optional)
2
3
3
4
7
8
8
9
10
Specications
Power Supply Input 15.6V DC-In
Dimensions* 12.4” ( 31.5 cm) W x 11.9” ( 30.2 cm ) D x 4.0” ( 10.2 cm ) H
Weight* 4.6 lbs ( 2.1 kg )
Operating Environment 5° C to 35° C ( 41° F to 95°F )
Storage Environment -20° C to 60° C ( -4° F to 140° F )
* DS-PAN-111
DECLARATION OF CONFORMITY FOR CE MARKING
Havis, Inc. declares that their DS-PAN-110 SERIES DOCKING STATIONS:
Are classied within the following EU Directives:
EU Electromagnetic Compatibility Directive 2004/108/EC
And further conform with the following EU Harmonized Standards:
EN 55022 (2006) + A1 2007, EN 55024 (1998) + A2: 2003
Dated: August 19, 2010
Position of signatory: Chief Information Officer / Chief Financial Officer
Name of signatory: Steve Ferraro
Signed:
• Do not place containers of liquid or metal objects on top of the Docking Station
• If a malfunction occurs, immediately unplug the Power Supply and remove the laptop
• Use only the specied Power Supply with this Docking Station
Recommended: Part # LPS-101 (90W) for CF-30, CF-31 Medium & Low Power Computers
Recommended: Part # LPS-104 (120W) for CF-31 High Power Computers
• Do not store the Docking Station where water, moisture, steam, dust, etc. are present
• Do not connect cables into ports other than what they are specied for
• Do not leave the Docking Station in a high temperature environment for a long period of time
(greater than +60°C, 140°F)
Precautions
www.havis.com • 1-800-524-9900
True Ethernet
RJ45
USB 2.0 Ethernet
RJ45
Parts Included
3 8
Docking Station
Forward Exiting Connectivity
Mounting Bracket
Hardware Kit
This Hardware Kit includes:
1. Zip Ties/Push Pins (2)
2. Keys (2)
3. 1/4”-20 Screws (7)
4. Zip Ties (6)
Tools required for installation:
• 5/32” Hex Drive
(For securing 1/4”-20 Screws)
Port Replication Capability
Headphone
MicrophoneUSB 2.0 (4)
+ Front USB 2.0 (1)
Serial (2)VGA Wireless On/Off*
Power Input
Rearward Exiting Connectivity (Optional Single or Dual Antenna)
Antenna A Antenna B
5). For theft deterrence, secure computer by locking Docking Station with
supplied key.
6). Power on computer. The Dock Indicator LED will light up green to indicate
proper system function.
Operation - Docking (Continued)
Operation - Undocking
1). If previously locked, unlock Docking Station using supplied key.
2). Rotate Latch Handle clockwise to the “UNDOCK” position.
Latch Handle
Docking Connector
Brass Locator Pin
Front Hook
Brass Locator Tab
Front USB Port
Dock Indicator LED
Lock
Dock Indicator LED
GREEN: Computer docked, all ports ready for use.
ORANGE: USB and LAN ports are not functioning.
RED: Computer is not supported or a connection is not made.
RED (Blinking): Firmware error has occurred.
NOT LIT: Computer is not installed, is turned off, or in standby or sleep mode.
For CF-30 computers, WWAN pass-through can be controlled according to Wireless On/Off switch setting.
For CF-31 computers, WWAN will always function as pass-through regardless of switch setting.
* NOTE
Loading...