Havis C-HDM-410, C-HDM-412, C-HDM-401, C-HDM-403, C-HDM-409 Installation Instructions Manual

A-

GUIDE RING BUSHING REMOVAL

WE STRONGLY RECOMMEND NOT TO REMOVE THE
GUIDE RING BUSHING, BUT IF REMOVAL OF INNER POLE
IS DESIRED - FOLLOW THIS SIMPLE REMOVAL
INSTRUCTION

INSERT MAXIMUM 1" DIAMETER OBJECT WITH

1.
SUFFICIENT LENGTH AND DROP INSIDE INNER POLE.
MAKE SURE NOTHING PREVENTS GUIDE RING

2.
BUSHING FROM BEING EJECTED UNDERNEATH. HIT
WITH A HAMMER TO FORCE THE GUIDE RING
BUSHING OUT.

7/8" - 1"

DIAMETER

OBJECT

SUPPORT ARM

(OPTIONAL)

B -

INSTALL SPIDER COLLAR (OPTIONAL

COMES WITH C-HDM-401 & 403)

IF MOUNTING THE SPIDER COLLAR TO THE INNER

1.
POLE USE CM003406 REDUCING BUSHING. SPREAD
AND SNAP OVER THE INNER POLE.
LOOSELY ATTACH SPIDER COLLAR TO THE OUTER

2.
POLE OR CM003406. DO NOT MOUNT SPIDER
COLLAR ABOVE OUTER POLE HORIZONTAL CUT.

SPIDER MUST BE
BELOW THIS SLOT
ON THE OUTER POLE

C -

INSTALL OPTIONAL C-HDM-416

IF MOUNTING C-HDM-416 TO THE INNER POLE USE

1.
CM003406. SPREAD THE PIECE AND IT SHOULD SNAP
OVER THE INNER POLE.
ATTACH C-PM-101 TO CLAMP ASSEMBLY USING

2.
LONG CARRIAGE BOLTS INSERTED THROUGH THE
PRINTER AND ONE PIECE OF EXTRUSION.
ATTACH POLE CLAMP TO THE OUTER POLE OR

3.
CM003406. AFFIX SECOND PIECE OF EXTRUSION
AROUND POLE AND LOOSELY TIGHTEN THE
HARDWARE. DO NOT MOUNT CLAMP ABOVE
OUTER POLE HORIZONTAL CUT.

CM003406 REDUCING

BUSHING IS NECESSARY

IF MOUNTING TO

THE INNER POLE.

(USE ONLY ON FIXED

HEIGHT POLES)

C-PM-101
SOLD SEPARATELY

D-

INSTALL GAS SHOCK (OPTIONAL)

(SKIP IF GAS SHOCK IS NOT IN USE)

1.
UNSCREW SMALL PLASTIC DISC FROM SHOCK

2.
INSERT GAS SHOCK ASSEMBLY UPWARD FROM
THE BOTTOM OF HDM POLE ASSEMBLY WITH GAS
SHOCK'S ROD FACING DOWNWARD. GAS
SHOCK WILL SANDWICH BETWEEN MOUNTING
BASE C-HDM-100 SERIES (NOT SHOWN) AND
ACTION ADAPTER C-HDM-300 SERIES (NOT
SHOWN).
ONCE GAS SHOCK SITS PROUD OF THE INNER

3.
POLE REATTACH SMALL PLASTIC DISC

GAS SHOCK
(OPTIONAL)

E -

INSTALL C-HDM-409 OPTIONAL

& COLLAR CLAMP ALIGNMENT

THIS CAN BE DONE EITHER AT THIS POINT OR ONCE

1.
THE C-HDM-100 SERIES BASE IS ALREADY IN THE
VEHICLE. YOU WILL NEED THE OFFSET THAT WAS
WIITH THE C-HDM-100 BASE IF APPLICABLE.
DECIDE ON THE ORIENTATION OF THE C-HDM-409.

2.
ENSURING THAT IF THE HANDLE VERSION OF THE
POLE IS BEING USED THE TWO SLOTS ARE NO MORE
THAN 45 DEG APART IF THIS IS THE CASE ROTATE THE
POLE TO THE CORRECT POSITION.
IF NO HANDLE IS BEING USED ENSURE THE OUTER

3.
POLE SLOT AND THE CLAMP COLLAR SLOT LINE UP.
TIGHTEN ALL THE HARDWARE.

4.

F -

INSTALL C-HDM-410-412 OPTIONAL

THIS CAN BE DONE EITHER AT THIS POINT OR ONCE

1.
THE C-HDM-100 SERIES BASE IS ALREADY IN THE
VEHICLE. YOU WILL NEED THE OFFSET THAT WAS
WIITH THE C-HDM-100 BASE IF APPLICABLE.
DECIDE ON THE ORIENTATION OF THE OFFSET.

2.
ENSURING THAT IF THE HANDLE VERSION OF THE
POLE IS BEING USED THE TWO SLOTS ARE NO MORE
THAN 45 DEG APART IF THIS IS THE CASE ROTATE THE
POLE TO THE CORRECT POSITION.
IF NO HANDLE IS BEING USED ENSURE THE OUTER

3.
POLE SLOT AND THE CLAMP COLLAR SLOT LINE UP.
TIGHTEN ALL THE HARDWARE.

4.

45°

MAX

45°

MAX

SLOTS IN TUBE
AND CLAMP
ALIGNED

HAMMER

PROJECT #

REV.

DESCRIPTION

DATE

BY

CHECKED BY

1765

3-13

REVISION DATE CORRECTED TO PT895 DOCUMENTED CHANGE.

NO OTHER CHANGES

8/5/2014

KDAVIS

75 JACKSONVILLE RD,
WARMINSTER, PA. 18974
1-800-524-9900

SIZE

SCALE: 1:8

SHEET 1 OF 4

DO NOT SCALE DRAWING

WEIGHT (LB): 12.634

TITLE:

DWG. NO.

C-HDM_INST

REV

A

3-13

HAVIS, INC.

INSTALLATION INSTRUCTIONS, C-

HDM MOUNTING BASES

C-HDM-204 SHOWN

STANDARD FLAT SURFACE

MOUNTING

F

OR FLAT SURFACE MOUNTING OF C-HDM­204, 205, 212, 213, 214, 215, 216 AND 217
(INCLUDING HAVIS CONSOLES WHICH DO
NOT HAVE HOLES PRE-DRILLED)

POSITION POLE MOUNT IN DESIRED

1.

LOCATION
MARK AND DRILL 1/4" HOLES INTO THE

2.

MOUNTING SURFACE (SEE NOTES FOR
DRILLING)
THROUGH-BOLT USING 1/4" HARDWARE

3.

PROVIDED WITH THE MOUNT OR
EQUIVALENT HARDWARE IF NECESSARY.

C-HDM-204 SHOWN

STANDARD CONSOLE SIDE

MOUNTING

FOR CONSOLE SIDE MOUNTING OF C­HDM-204, 205, 212, 213, 214, 215, 216 AND
217 (WHERE CONSOLE HAS PRE-INSTALLED
NUTS IN CONSOLE RAIL)

TO ATTACH C-HDM-204, 205, 214, 215

1.
LOOSEN THE RETAINING SET SCREW TO

2.
ALLOW THE NUTS TO BE POSITIONED AS
DESIRED IN THE TRACK.
LINE UP THE MOUNT WITH THE NUTS IN

3.
THE CONSOLE,
ATTACH USING HARDWARE

4.
PROVIDED WITH THE MOUNT, OR
EQUIVALENT 1/4-20 X 1/2" LONG
(MAX.) BOLTS AND FLAT WASHERS.

C-HDM-204 SHOWN

PRE-DRILL;ED CONSOLE SIDE

MOUNTING
FOR CONSOLE SIDE MOUNTING OF C­HDM-204, 205, 212, 213, 214, 215, 216 AND
217 (WHERE CONSOLE HAS PRE-INSTALLED
NUTS IN CONSOLE RAIL)

TO ATTACH C-HDM-204, 205, 214, 215

1.

LINE UP THE MOUNT WITH THE

2.

PREDRILLED HOLES IN THE CONSOLE,
ATTACH USING HARDWARE PROVIDED

3.

WITH THE MOUNT, OR EQUIVALENT 1/4­20 BOLTS.
DEPENDING ON THE DESIRED POSITION,

4.

HOLES MAY NEED TO BE DRILLED, OR
ONE (1) BOLT CAN USE THE NUT TRACK
WITH A 1/4-20 X 1/2" LONG BOLT.

FOR VEHICLE MOUNTING THAT REQUIRES DRILLING

INSPECT ALL AREAS BEFORE DOING ANY DRILLING

1.
ENSURE NO SERIOUS DAMAGE HAPPENS TO THE
VEHICLE.
SECURE THE MOUNT WITH SUPPLIED HARDWARE KIT.

2.

NOTE:
MOST C-VS (VEHICLE SPECIFIC)
SERIES CONSOLES HAVE HOLES FOR
AN HDM-204 OR 214 PRE-DRILLED.
IF ANOTHER LOCATION IS DESIRED,
HOLES MAY NEED TO BE DRILLED

75 JACKSONVILLE RD,
WARMINSTER, PA. 18974
1-800-524-9900

SIZE

SCALE: 1:8

SHEET 2 OF 4

DO NOT SCALE DRAWING

WEIGHT (LB): 0.00

TITLE:

DWG. NO.

C-HDM_INST

REV

A

3-13

HAVIS, INC.

INSTALLATION INSTRUCTIONS, C-

HDM MOUNTING BASES

D-

C-HDM-417 VERTICAL

PRINTER MOUNT SHOWN
WITH C-PM-101 ATTACHED

F-

EXAMPLE OF A FINISHED ASSEMBLY

THE ABOVE ASSEMBLY INCLUDES A C-HDM-102, C-

1.
HDM-202, C-MD-102, C-HDM-403, C-HDM-404(2X)

B-

C-HDM-401 SUPPORT ARM

LOOSELY ATTACH SPIDER (CLAMP) COLLAR TO

1.
POLE WITH HARDWARE SUPPLIED (IF NOT ALREADY
ATTACHED). POSITION AS DESIRED AND TIGHTEN
HARDWARE.
LOOSELY ATTACH C-HDM-401 USING HARDWARE

2.
PROVIDED.
FIND A SUITABLE LOCATION TO ATTACH THE OTHER

3.
END OF THE SUPPORT ARM. SOME VEHICLES HAVE
HOLES UNDER THE DASH OR OEM HARDWARE THAT
CAN BE UTILISED. LOOSELY ATTACH TAB PROVIDED.
EXTEND THE ARM ATTACHING THE TAB TO THE

4.
SUPPORT ARM WITH THE HARDWARE PROVIDED.
TIGHTEN ALL HARDWARE.

5.

A-

C-HDM-403 HORIZONTAL PRINTER

MOUNT

LOOSELY ATTACH SPIDER (CLAMP) COLLAR TO

1.
POLE WITH HARDWARE SUPPLIED (IF NOT
ALREADY ATTACHED). POSITION AS DESIRED
AND TIGHTEN HARDWARE.
ATTACH C-HDM-403 PLATE USING HARDWARE

2.
PROVIDED. AVOID TIGHTENING SCREWS IF AN
OFFSET ARM IS TO BE ADDED.
ATTACH DESIRED ITEM TO SHELF BRACKET.

3.

THE C-HDM-403 WORKS VERY WELL IF THERE IS

4.
NO CENTER CONSOLE. SPACE IS VERY LIMITED
AND WILL CAUSE LACK OF LEG ROOM IF THE
VEHICLE DOES HAVE A CENTER CONSOLE.

C-

C-HDM-404 SUPPORT ARM

THE C-HDM-404 IS PRIMARILY USED FOR UNIVERSAL

1.
FLOOR MOUNTS WHEN PREMIUM STRENGTH / 3
POINT MOUNTING IS NECESSARY.
COMPLETE SECTION B.

2.
LOOSELY ATTACH C-HDM-404 USING HARDWARE

3.
PROVIDED.
THE MAJORITY OF HAVIS BASES HAVE AN EXTRA PEM

4.
IN ORDER TO ATTACH TO THE SUPPORT ARM. IF NOT
FIND ANOTHER LOCATION OR DRILL AND THROUGH
BOLT THE TAB BRACKET.
EXTEND THE SUPPORT ARM AND ATTACH WITH

5.
SUPPLIED HARDWARE.
TIGHTEN ALL HARDWARE.

6.

D-

C-HDM-417 VERTICAL PRINTER MOUNT

COMPLETE SECTION B.

1.
LOOSELY ATTACH C-HDM-417 BRACKET USING THE

2.
HARDWARE PROVIDED.
SLIDE TWO CARRIAGE BOLTS IN THE C-PM-101 SLOTS.

3.
LOCATE THE TWO HOLES IN THE C-HDM-417

4.
BRACKET PUSH THE CARRIAGE BOLTS THROUGH THE
HOLES AND FINGER TIGHTEN THE SERRATED NUTS
PROVIDED.
SLIDE THE PRINTER TO THE RIGHT POSITION AND

5.
TIGHTEN ALL HARDWARE.

E-

ATTACHING THE SHAFT STOP
COLLAR THAT COMES WITH
TELESCOPING POLE WITH HANDLE

SLIDE THE INNER POLE TO THE DESIRED HEIGHT.

1.

ATTACH THE SHAFT COLLAR USING THE HARDWARE

2.

PROVIDED.
INNER POLE SHOULD NOW SPIN FREELY WHILE

3.

MAINTAINING THE DESIRED HEIGHT.

75 JACKSONVILLE RD,
WARMINSTER, PA. 18974
1-800-524-9900

SIZE

SCALE: 1:8

SHEET 3 OF 4

DO NOT SCALE DRAWING

WEIGHT (LB): 19.41

TITLE:

DWG. NO.

C-HDM_INST

REV

A

3-13

HAVIS, INC.

INSTALLATION INSTRUCTIONS, C-

HDM MOUNTING BASES

1/4-20 NYLOCK NUT (2X)

1/4-20 FEMALE HANDLE

C-HDM-301
INCL WITH
C-HDM-302,
303, 304.

GENERAL C-HDM-300's INSTALL INSTRUCTIONS

ALIGN 4 MOUNTING STUDS OF MOUNTING DEVICE C-HDM-

1.
300's INTO THE HDM-200's SERIES MOUNTING SLOTS.
BOLT THE MOUNT TOGETHER USING SPECIFIED AND SUPPLIED

2.
HARDWARE.
TORQUE THE 5/16 HARDWARE TO INDUSTRY STANDARDS .

3.
1/4-20 FEMALE HANDLE CAN BE SUBSTITUTED FOR 1/4-20

4.
NYLOCK NUT.
IF THE C-HDM-300 IS TO BE STATIONARY BOLT DIRECTLY TO

5.
THE POLE USING 5/16-18 HARDWARE.
VISIT US AT www.havis.com TO SEE PICTURES OF

6.
INDIVIDUALLY INSTALLED PRODUCTS.

1/4-20 THIN

NYLOCK NUT (4X)

SECTION REMOVED FOR CLARITY

C-HDM-402 (OPTIONAL) SAFETY LOCK
WITH C-HDM-305

FOLLOW GENERAL C-HDM-300's INSTALL

1.
INSTRUCTIONS IN "HOW TO ATTACH C-HDM-402
INTO UPPER POLE".
MOUNT C-HDM-305 (SLIDE) TO SAFETY LOCK (C-

2.
HDM-402) USING SHOWN HARDWARE AND
FOLLOWING THE HARDWARE ARRANGEMENT.
THE TOP PLATE CAN BE REMOVED IF NECESSARY
TIGHTEN HARDWARE AND REATTACH TOP PLATE.

3.

C-HDM-402

TOP PLATE

C-HDM-305

1/4-20 X 3/4" HEX HEAD BOLT (4X)

1/4" SPLIT LOCK WASHER, (4X)

1/4" SAE FLAT WASHER, (8X)

C-HDM-301 TO C-MD-200 SERIES

ALIGN 4 MOUNTING STUDS OF MOUNTING DEVICE C-HDM-

1.
300's INTO THE C-HDM-200's SERIES MOUNTING SLOTS.
BOLT THE C-MD-200 TO THE C-HDM-301 PLATE USING THE

2.
SAME HARDWARE CONFIGURATION FOR THE C-HDM-300
SERIES.
TIGHTEN HARDWARE.

3.

C-MKM-100 SERIES TO C-HDM-200
SERIES

NUT AND BOLT TOGETHER UTILIZING C-HDM-

1.
301 AS SHOWN ABOVE.

C-MD-100 SERIES

PLACE C-MD-100 SERIES MOTION DEVICE ON

1.
TOP OF POLE MOUNTING SURFACE.
LINE UP THE 4 TAPPED HOLES WITH THE UPPER

2.
POLE MOUNTING SLOTS.
ATTACH THE FOUR 1/4-20 HEX BOLTS & LOCK

3.
WASHERS AND FLAT WASHER AS SHOWN
THROUGH THE THREADED HOLES OF THE
MOTION DEVICE.
TIGHTEN HARDWARE.

4.

C-HDM-200's SERIES

(NOT INCLUDED)

5/16-18

HEX NUT(4X)

5/16" SPLIT LOCK

WASHER(4X)

5/16" STEEL

FLAT WASHER (4X)

1/4" PLASTIC

FLAT WASHER (3X)

1/4" STEEL

FLAT WASHER (3X)

75 JACKSONVILLE RD,
WARMINSTER, PA. 18974
1-800-524-9900

SIZE

SCALE: 1:8

SHEET 4 OF 4

DO NOT SCALE DRAWING

WEIGHT (LB): N/A

TITLE:

DWG. NO.

C-HDM_INST

REV

A

3-13

HAVIS, INC.

INSTALLATION INSTRUCTIONS, C-

HDM MOUNTING BASES