Hausmann 1427 Installation & Operation Instructions
Product Specifications
Model #
Length
Width
Height
Weight Capacity
1427-46
6’
4’
20” – 30”
750 lbs
1427-47
7’
4’
20” – 30”
750 lbs
1427-57
7’
5’
20” – 30”
750 lbs
1427-68
8’
6’
20” – 30”
750 lbs
Part Lists
Part
Qty
Description
A 1 Upholstered Top
B
4
Black Steel Aprons (2 long, 2 short)
C
4
Corner Steel Legs
D 4 Hydraulic Lift Cylinder/Legs
E
1
115 V Motor/Hydraulic Pump Assm.
F
4
Adjustable Leg Levelers
G 1 Foot Control, 12V DC with 6’ cord
H 1 Control Box
Platform Ships Fully Assembled
Figure 1: Mat Platform
A
C
B D F
G
130 Union St • Northvale NJ 07647 USA • Tel: (201) 767-0255 • Fax: (201) 767-1369 • www.hausmann.com
A) INSTALLATION INSTRUCTIONS
Installation/Operation Instructions
Model 1427 – Bariatric Electric Mat Platform
1. Remove all packaging material from the platform.
2. Plug the power cord into a properly grounded 120 Volt AC
outlet and follow the procedure outlined in the
precautionary instructions.
Leveling the Platform:
1. Place the table in position before leveling.
2. Use adjustable wrench to rotate leg levelers for height adjustment.
B) OPERATING INSTRUCTIONS
Duty cycle on/off Int. 2 min./ 18 min.
1. Raise the platform by gently pressing the up arrow on the footswitch.
2. Lower the platform by gently pressing the down arrow on the footswitch.
C) MAINTENANCE
In the event it becomes necessary to replace the foot switch or power cord, make certain that the component is
connected properly and the locking tabs on the motor snaps in place.
For assistance please call Hausmann Industries at (201) 767-0255, press 5 for Customer Service. We may request
purchase details (product, date purchased, dealer) to better assist you.
Rev. 072514 aj Page 1 of 7 ©2013 HAUSMANN INDUSTRIES, INC.
®
Movotec
Q-Drive Motorized Lift Systems
Refill Instructions
Movotec® Refill Kit Contents
Movotec® Refill Instructions
Movotec® NT15 Hydraulic Fluid MSDS
(0.5) Liters (16.9 oz.) of Movotec® NT15 Hydraulic Fluid
Filler Bottle
Filler Bottle Cap
Filler Bottle Needle
(10) Meters (32.8 ft.) of Movotec® Flexible Hydraulic Tubing
(12) Ferrules
(12) Compression Nuts
1.0 Safety Instructions
This document contains safety and user service instructions for refilling a Movotec® Q-Drive Motorized Lift System. Suspa
®
Incorporated is not responsible for any alteration or deviation from these instructions resulting in property damage, personal
injury or death.
FAILURE TO FOLLOW THE INSTRUCTIONS IN THIS DOCUMENT COULD
RESULT IN FIRE, PROPERTY DAMAGE, ELECTRC SHOCK, PERSONAL
INJURY OR DEATH.
The instructions in this document are intended to be used in conjunction with the Movotec® Refill Kit. The Movotec® NT15
hydraulic fluid contained in this kit is specially formulated for the improved performance of our lift systems. DO NOT, FOR
ANY REASON, USE ANY FLUID OTHER THAN MOVOTEC® NT15 HYDRAULIC FLUID WHEN REFILLING A MOVOTEC® LIFT
SYSTEM.
READ ALL INSTRUCTIONS BEFORE ATTEMPTING TO REFILL A MOVOTEC® LIFT SYSTEM.
2.0 System Preparation
2.1 Motorized System Preparation.
Lower the system by holding “down” arrow button on the switch. Continue holding “down” arrow button until all lift
cylinders have reached their fully retracted position. Remove finger from the switch. Then, press and hold “down” arrow
button again. After approximately 5 seconds the system will begin to retract until the “zero” position is reached. The system
is now fully retracted.
COMPRESS CYLINDERS COMPLETELY
Rev. 072514 aj Page 2 of 7 ©2013 HAUSMANN INDUSTRIES, INC.
Once the system has reached the “zero” position, unplug power
cord from the power outlet. Then disconnect motor cable from
controller (keep cables plugged in to back of motor drive).
2.2 Cylinder Preparation
To properly refill a cylinder, the load must be removed from all cylinders and/or the workstation. For Movotec® “Bolt-On” lift
systems, this can be achieved by lifting the entire workstation off of the floor with a lift truck or pallet jack. Blocks can be
used to stabilize the workstation during the refill procedure.
For Movotec® ATU and Corner Leg systems, lift cylinder(s) that are to be refilled must be removed from their corresponding
support leg. Movotec® ATU lift systems will require external retaining ring pliers to remove the 13mm retaining ring from the
top of the lift cylinder. For Movotec® Corner Leg lift systems, a T25 torx driver will be required to remove (4) torx screws at
the top of the corner leg support housing. Additionally, external retaining ring pliers will be required to remove a 13mm
retaining ring and upper cap from the top of the lift cylinder.
ATU Cylinder Removal Corner Leg Cylinder Removal
Rev. 072514 aj Page 3 of 7 ©2013 HAUSMANN INDUSTRIES, INC.
Loading...