Page 1 Page 2 Page 3
Page 5 Page 6 Page 7 Page 8
Page 9 Page 10 Page 11 Page 12
Page 4
You can check to see if the driver has been installed correctly. Click on
Start / Settings / Control Panel / System / Hardware / Device
Manager.
If you then click on the Sound
Video and Game Controllers sec-
tion you should see the eight
WinTV-HVR components.
If any of them have a yellow
exclamation mark, follow this procedure:
1.Close Device Manager
2.On the Hauppauge Installation
CD-ROM double click on the file
called “HCWclear.exe” and
select the last 2 options and
click on OK.
3.Once the black screen has clo-
sed down, re-start the computer and continue from Step 5
above.
WinTV-HVR-3000
Quick Installation Guide for Windows XP
© 2006 Hauppauge Computer Works · QI-WINTV-HVR3000-V1.0-ENG · 2006/06/22
● WinTV-HVR-3000 - PCI-board
● Remote control transmitter with
2 AAA batteries
● Remote control receiver
with velcro dot fastener
● FM Radio antenna
● S-Video/Composite Adapter
● Installation CD-ROM with:
· WinTV2000 application with
SoftPVR™
· WinTV-Scheduler
· Remote Control application
· WinTV-Radio application
· WinTV Utilities
· VTPlus teletext application
To install, switch off the computer and remove the computer cover.
The manufacturer of your PC supplies instructions on removing the PC
cover.
N
ote: Your PC could be damaged by electrostatic discharge.
Avoid this by contacting the earthed chassis of your PC,
before you open it or touch the PCI card.
● Locate a free PCI slot (a short white slot). Unscrew and remove the
meta cover plate which covers the back of the empty slot.
● Plug the WinTV-HVR board into the PCI slot, and screw the WinTV-
HVR metal cover plate to the PC.
2. Installing the WinTV-HVR board
With the HVR you can watch and record analog TV, DVB-Terrestrial and
DVB-Satellite channels. You can also connect sources via the composite and S-Video inputs and listen to FM Radio as well.
You can now connect the leads provided to the WinTV-HVR-3000 in
the following order.
FM FM Radio-Antenna
TV TV-Antenna
SAT SAT-Cable from the LNB of your satellite dish
S-VIDEO IN S-Video-Input *
LINE IN Stereo-Audio-Input, from the output of your source
IR Input for the Infra-red-Sensor
N
ote: for using a RCA Yellow Phono composite input you
must use the supplied S-Video to composite adapter.
3. Connections of the WinTV-HVR-3000 board
DVB-T
Please ensure that you have a suitable TV aerial connected to the
WinTV card. You should then ensure you are located in a area that
supports Digital Terrestrial TV by visiting:
www.dtg.org.uk/retailer/coverage.html and entering your post code.
If your area does have digital Terrestrial TV coverage, please check
your TV antenna as most antenna’s that are over 8 years old may not
support the Digital Terrestrial TV broadcasts and you may need to
update yours to a ‘Wideband or Highgain’ antenna.
DVB-S
Please ensure that your satellite dish is correctly aligned and the Sat
cable is connectly directly from the LNB and not via a set top box.
4. WinTV-HVR-3000 DVB reception advice
N
ote: You may need to disable your antivirus programs during
the installation only.
5. Install the WinTV-HVR Windows XP driver
Start your PC. When it is completely booted, the Add New
Hardware Wizard will appear.
Insert the Hauppauge Installation
CD-ROM into your CD-ROM
drive. Click Next.
Select Search for the best driver
for your device (Recommended).
Click Next.
N
ote: If you see a
Hardware Installation
box that mentions that
the driver is not digitally
signed, click the “Continue
anyway” button to continue
the installation.
Once the driver components are
installed, click the Finish button.
To start the WinTV2000 software
installation, click Start / Run then
type your CD-ROM drive letter
(for example: D:\) and then
Setup.exe.
Select your language and click
Next.
It is recommended to leave the
default components ticked and
select Install and follow the on
screen instructions.
6. WinTV Software Installation
To start the WinTV2000 application double click on the
WinTV2000 icon.
A message will appear asking you
to scan for tuner channels now;
please ensure that the TV antenna
is connected, click YES.
Snapshot
Still capture
Freeze pic
CFG
Configure
Snapshop
PREF
Configuration
Setup Menu
TV mode
Remove toolbars “no title”
Minimize
Channel surf
Channel down
Channel up
Last channel
Current TV channel
Click your right mouse
button here to see
channel selector
Click your right mouse button in the TV
window to remove toolbars.
Click again to restore toolbars.
One Touch Pause
Record - Opens the
playback controls
Volume
Full screen TV
Always
on top
TV Mode
When you click the Full screen TV button, TV will appear full
screen on your PC monitor. When finished watching TV full screen,
click your right mouse button in the TV window. If you see video with
a black box around it, click the Pref button then click TV mode tab.
Check the box which says “Allow resolution change”.
Snapshot view
window:
Double click on
each "thumbnail"
to see image full
size.Click and hold
your right mouse
button to see
image options.
One Touch Record
Pause
TV Time-Shift-
TV-Mode
Close
WinTV
"Always on top" Mode
Will always be visable on your Windows desktop on top any
applications. To turn on, click the Always on top button. It will turn
green. To turn off, click this button again. A convenient way to use
Always-on-top is to make the TV window in the no-title mode small,
and to make the TV window in the title mode larger. Then you can
switch from a small window to a larger one by clicking the right
mouse button.
Changing channels
You can change channels by using the Channel Up or Channel Down
buttons on the WinTV2000. You can type a channel number (for example: 27) and WinTV2000 will tune to that channel. If the entered channel does not exist, you will see a black window.
You can also type letters (for example: BBC) to access to the list of the
channels including these letters.
Menu Button
Click the Menu button to open the TV setup menu. Here is the
main control bar for TV channels, and duplicate controls for other
functions:
Suite-Manager: Configure the TV tuner (scanning, naming, channel
pre set, etc) and setting up favourite channel lists.
Configuration: Duplicate configuration menus for colour, audio, MPEG
settings (except DVB TV), etc.
View: For settings (except DVB TV) an exact TV window size:
320x240, 640x480 etc.
Pref button
View: These setting mainly control the Screen display for the
TV channels and Audio volume. This menu will also allow you to
enable close caption (if supported in your system configuration), plus
controls for the Toolbar mode (Title mode), NoToolbar mode (No Title)
and Full Screen (TV mode).
Movies: Here is where you configure the video and audio setting for
SoftPVR. You can set the movie record directory (DVCR Record File
Path), the MPEG Quality settings, and the Audio settings.
Snapshot: Set the size of your captured images, plus single or two
field captures for capturing motion or still image video.
Audio: Your audio settings are configured here.
Colour: Adjust the colour of you TV picture here (analogue TV).
One Touch Pause One Touch Recording
TV Mode Pause Mode Record Mode
Clicking on the “OTP” (One-Touch-Pause) prepares WinTV2000 for the
Pause-Mode mode (see below).
Clicking on the “OTR” (One-Touch-Record) prepares WinTV2000 for
recording. If you press the “OTR” once it will record for 15 minutes
duration, if you immediately press again it will add another 15 mintues
(so in total 30 mins).
Record Mode
Click on the Record button or the OTR button on the WinTV2000 application to open the Record and Playback control bar.
Time counter
The time is specified in a Hour:Minute:Second format.
Record
Clicking the Record button will automatically generate a file name
and start recording your audio/video program.
Functions:
● When recording TV the record button will depressed
● A time counter will be shown indicating the lenght of time of the
recording
If you click Stop the time counter will revert back to 00:00:00
Stop
Clicking the Stop button will stop the video you are recording or
playing back.
Play
Clicking the Play button will playback from disk the last video file
created. When playing a video, you can rewind, fast forward, replay 10
sec or skip forward 10 sec using the buttons on the control bar.
Pause
Clicking the Pause button while Playing will pause your
audio/video.
Rewind button
Clicking the Rewind button will play the video file in reverse.
Clicking the Rewind button again will continue the playing of the
video.
Fast forward button
Clicking the Fast Foward button one time will fast foward your
video at 2X speed. Clicking the Fast Foward button two times will fast
foward your video at 8X speed. Clicking the button again will continue
playing back at normal speed.
Slow motion button
Clicking the Slow Motion button during playback will cause the
video to play in slow motion. Clicking the Slow Motion button again
will return the video to normal playback speed.
File button
Clicking the File button opens the File menu. The last file recor-
ded is listed in the File name box. In the File menu you can:
● Rename your recorded video file: To rename a video file, find the
file you would like to rename, highlight it with your mouse, and click
and hold the right mouse button. Go down to Rename and then you
can type in a new name. Remember: you must keep the MPG extension on the file.
● Play a video file previously recorded: Find the file you would like to
play, highlight it with your mouse (one click of the mouse button)
and click Open. Then click the Play button.
● Delete recorded video files which you no longer want: Click your
right mouse button on the video file once, go down the menu and
click Delete.
Pause Mode
The pause mode allow you to pause the Live TV picture and allows
you to use the TimeShift function to rewind and fast forward the TV.
Clicking the Pause button or
OTP button on the WinTV2000 application
starts the Pause mode. The Pause Menu will drop down.
Slow motion
Clicking the Slow Motion button while playing video will play in Slow
Motion. Clicking the Slow Motion button again, will continue playing
normally.
Fast forward button
Clicking the Fast Forward button one time will fast forward your video
at 2X speed. Clicking the Fast Forward button two times will fast forward your video at 8X speed.
Keyboard shortcuts
Sound up - Page Up
Sound down - Page Down
Plus (+) - Channel Up
Minus (-) - Channel Down
Ctrl+T - Frame TV
Ctrl+P - Frame Print
Ctrl+F - Still image
Ctrl+M - Mute on/off
ALT+M - Re-size TV menu
0-9 - Channel number
F1 - Launch Help
SHIFT+F1 - Online Help
Space bar - Take a Snapshot
WinTV-Scheduler allows you to schedule the recording of TV shows.
WinTV-Scheduler, once it is set, can be closed, and the WinTV application will “wake up” at the desired time and tuned to the desired channel.
After installation, WinTV-Scheduler can be found by going to Start /
Program Files / Hauppauge WinTV.
WinTV-Scheduler works by using the Windows Task Scheduler to
launch WinTV at the chosen time. WinTV-Scheduler sets up a command line in Task Scheduler to run WinTV2000, specifying a TV channel and a length of time to record.
To set up an event for timed watching or recording, run WinTVScheduler and click on the Add Program.
N
ote: You cannot access the Wing settings until you have purchased the optional transcoder software, for more informations see www.hauppauge.com/wing. Please refer to the
WingSE guide for information on using the Wing settings.
The items that need to be set for each event are:
● Time to Begin Program: set to the desired start time. The default
time is about 3 minutes from the current time. Click on the hour to
set the hour, the minute to set the minute and the second (if you feel
this is necessary) to set the second to start the program.
N
ote: It takes about 10 seconds to launch the WinTV and set
up for recording, so set the Time to Begin Program to 1
minute before the time your TV show actually starts.
● Time to End Program: set to the time to end this event.
N
ote: you need to leave at least 30 seconds between scheduled programs to give the recorder time to set up its disk buffers.
● Program Period: one time, daily, weekly.
● Date to Begin Program: today’s date is the default. Change this if
you want to schedule on another date.
● Source selection: leave set at WinTV2000 to bring up the WinTV at
the requested time and on the requested channel.
● Channel selection: choose one of your scanned channels.
● Recording options: click on Record to File to record your show.
Leave this button unchecked to watch TV at the requested time. You
can also name your file to record.
10. WinTV-Scheduler
The WinTV2000’s remote control software is installed automatically
during the installation of the WinTV applications.
You will see the WinTV Remote icon in the Device Tray. The installation will add a shortcut to IR.EXE to the Startup group, so that IR.EXE is
loaded every time after Windows has booted.
If you need to restart the remote control, select Restart IR from the
Start \ All Program Files \ WinTV directory.
Please ensure the following before trying to use this option:
1.Infrared Remote control - Has batteries inserted
2.Infrared-Receiver, is fully connected to the IR socket of the WinTV-Card
3.Infrared software is started - The IR icon is on the start bar
To start WinTV press the GO button and a menu will appear. Use the
scroll up and down button to select either WinTV2000 or WinTV32 and
press OK to select.
Button of the Remote control
Button Function
Go: Open WinTV-Remote Menu
Power: WinTV turn on/off
TV: Full screen TV Window on/off
Videos: No Function
Music: No Function
Pictures: No Function
Guide: No Function
Radio: Start and Stop Radio
Application
OK: Confirm selection
Back/Exit: Exit the Record/Pause; Select
previous channel
Menu: Will show the Task manager
window for active screen
Vol: Volume up/down
Prev. Ch: Select the previous channel
Mute: Sound on/off
Ch: Select the next channel
REC: Start a recording
Stop: Stop a recording; Exit pause
mode
<<: Rewind
Play: Start playing
>>: Forward
Pause: Start Pause-Mode (Timeshift)
Skip: Skip ahead (x2/x 4/x8)
0-9: Channel number
text (*): Start VTPlus teletext application
7. Installing the Remote Control software
1. Contents of the WinTV-HVR-package
Click on the Analog/Digital Config
button and select your country
(United Kindom), source
(Antenna) and video format (Pal-
BGHIDK).
Click the Scan button to search
for channels.
To scan for satellite channels click on the Config and Advanced buttons. You will now be able to select your DiSEqC support level, which
for single LNB satellite installation will be “No”. Under the Satellite list
select the satellite that your dish is receiving signal from (UK 0282
ASTRA 2A,2B,2D (28.2E).
Click the Scan button to search for channels and click Close when
complete.
Record PlayPaus e Stop
File menu (save / open)
Time counter
Skip to end
Skip back 10 sec
Video-position
Fast forward
Slow motion
Fast rewind
Skip forward 10 sec
Skip back 10 sec
Rewind Replay last 10 secPause Play
Skip ahead 10 sec
Display Counter
Skip to end
Replay last 10 sec
Video-Position
Fast forward
Play forward slow
Fast ahead 10 sec
Skip to start
Pause Buffer
The Pause buffer is space on your hard disk where video is stored
during the Pause mode. The maximum amount of time which your TV
program can be delayed is dependent upon how much storage space
you have set for the Pause buffer.
Pause
Clicking the Pause button or OTP button causes WinTV2000 to
start recording into WinTV's Replay Buffer. It takes about 10 seconds for
the Replay Buffer to be initialized and for Pause to become effective.
Unclicking the Pause button will cause the audio/video program to start
playing from the point where the button was originally clicked.
Most WinTV2000 functions are active while in the Pause or Pause Live
mode. For example, you can change volume, resize the TV window, go
into "no-title mode", etc.
While in Pause mode, the Video Position bar shows the amount of the
Replay Buffer which is filled with video. For example, if the Video
Position indicator shows halfway, it means that half of the Replay
Buffer is filled. If you find you cannot Pause as many minutes as you
would like, increase the size of the Replay Buffer.
While in Pause mode, the A/V stream is always saved in the Replay
Buffer. To stop saving the A/V stream in the Replay Buffer, you must
exit the Pause mode by clicking TV mode.
Replay button
While in the Pause mode, hitting the Replay button acts like the
Instant Replay you see on TV broadcast sporting events: the
audio/video goes back in time and you repeat what you have previously seen. Each click of the Replay button causes audio/video to go back
10 seconds. For example, if you want to repeat the audio/video you
saw 10 seconds ago, you would click the Replay button once. If you
want to see the video you saw one minute ago, you would need to
click the Replay button six times.
For extended replay times, you might find it more convenient to grab
the Video Position indicator control bar and move it to the left. Once
you let the control bar go, audio/video starts to play (it might take a
few seconds for the WinTV2000 application to start playing).
You might have to move the Video Position indicator to the left and
right to find the desired spot to start replaying audio/video.
While Replaying, your audio/video program continues to be recorded
in the Replay Buffer. Therefore, if you have clicked the Replay button 3
times (so that you are replaying the audio/video seen 30 seconds ago),
the video you see in the WinTV window will be 30 seconds behind the
"live" audio/video program.
Skip ahead button
Clicking the Skip button will skip the video ahead 10 seconds.
Rewind button
Clicking the Rewind button while playing video will rewind the
recorded video. Clicking the Rewind button again will continue the
playing.
Hauppauge Computer Works, Ltd.
10 Borough High Street
Bank Chambers
London, UK, SE1 9QQ
www.hauppauge.co.uk
Tech Support: (+44) 0207 378 0202
Telephone: (+44) 0207 378 1997
Fax: (+44) 0207 357 9171
Hauppauge Computer Works, Inc.
91 Cabot Court
Hauppauge, NY 11788
www.hauppauge.com
Tech Support: (+1) 631 434 3197
Telephone: (+1) 631 434 1600
Fax: (+1) 631 434 3198
Hauppauge Digital Asia, Pte. Ltd.
Blk 1093, Lower Delta Road #04-05
Tiong Bahru Industrial Estate
Singapore 169204
www.hauppauge.com.sg
Tech Support: (+65) 276 4412
Telephone: (+65) 276 9163
Fax: (+65) 276 9167
8. WinTV®2000
There are three buttons to control the watching, recording and pausing
of TV. Clicking on the Pause button will cause the Pause menu to roll
down from the WinTV2000 application, while clicking on the Record
button will cause the Record menu to roll down.
Record-, Pause- and TV-Mode
If you are using a external source like a Hi-8 Camcorder, Video recorder etc, then you will need to connect via the S-Video/Composite for
the Video picture and Line-Input for the sound.
If you are using a Scart to composite (RCA Yellow phono) lead, please
ensure that the signal is being sent in the correct direction from the
Scart lead to the phono connection. A scart to S-Video lead, in most
cases, will not work correctly and will only give you a black and white
picture.
Configuring a external source in WinTV2000
In the WinTV2000 application click the Menu, suite manager and sources. To add the S-Video or Composite channel highlight the entry and
then select the Video Format from the drop down list.
N
ote: Pal BGHIDK is the commonly used format in Europe.
9. Using a external source
Once the installation is complete the WinTV2000 Icon will appear on
the desktop which will allow you to run Hauppauge WinTV.
The 7 day Electronic Program Guide (EPG) for DVB-T can be downloaded and installed from the www.hauppauge.co.uk website. See website for installation instructions.
Once downloaded double click on the DVB-T_EPGService_Setup.exe
program and follow the on screen instructions.
Type in a channel “Name” e.g. Video and a Description and then click
on “Save” the channel will now be added and if you click on Close you
will be returned back to the main TV viewing window.
Page 13 Page 14 Page 15 Page 16
Page 17 Page 18 Page 19 Page 20
11. WinTV-Radio (for radio FM)
Please ensure that the FM Radio antenna is connected to the FM connection on the back of the WinTV-HVR.
N
ote: DVB-T and DVB-S Radio stations will be listed in the TV
channel list in the WinTV2000 application.
To start the WinTV-Radio, click the Start / Programs / Hauppauge
WinTV and the “Radio” application shortcut.
Using the WinTV-Radio buttons
Volume: The audio volume is adjusted by setting the Windows volume Line In.
Tune: Fine tune the current radio channels.
Seek: Search for the next active FM radio channel.
Mem: Sets an FM radio channel preset. To assign the current station
to a preset, click on MEM and then on one of the Preset buttons (1-30).
Mute: Turns off the sound.
Mono: Force mono reception. Default is stereo.
Scan: Searches for new stations until you click “Stop”. Click the Right
mouse button anywhere on the WinTV-Radio window to set the Scan
mode.
Min: Minimizes the WinTV-Radio window.
CD: Starts your systems Audio CD-player for playing back Audio-CD’s.
Closes the radio application and starts the WinTV application.
OFF: Closes the radio application.
1 to 10: Preset 1 - 30 Stations list (1..30).
Mem button now saves existing preset to new preset number or
swaps with existing: When saving presets if the target preset already
exists and the current channel is also a preset then the two presets are
swapped allowing the user to reorder the preset list. If the user saves
a current preset to a new empty preset the the original preset is
moved to the new location. If the target preset exists and the current
station is NOT an existing preset then the user is prompted before
destroying the existing preset.
Supports 30 User Defined Presets: Each Preset button holds up to 3
presets each. Press the button to go to the next preset. The Mem button cycles through FM1, FM2, and FM3 bands to specify where to
save a new preset.
User defined display names for Presets:
When the radio is tuned to a preset the user can assign a name by
clicking the mouse on the frequency display and typing in a name that
VTPlus for WinTV-HVR is a Teletext software application which is available on the analogue and DVB-S (not DVB-T) channels of the HVR.
VTPlus allows you to view multiple teletext pages, save or print teletext pages and create Dynamic Data Links so that teletext data can be
used in other applications. The WinTV application does not have to be
active while the VTPlus teletext application is running.
Please ensure that you have already scanned in your TV channels
before starting VTPlus.
To start the VTPlus application click on the Start / All Programs /
VTPlus for WinTV. Please refer to the online Help menu in the application for instructions.
12. VTPlus application
To uninstall the Driver and Software
To uninstall the software simply run the hcwclear.exe off
theHauppauge installation CD-ROM and select the last 1 option and
the entry “search all INF files etc”. If you now select “OK” a black
screen will briefly appear and once it has disappeared the software
will be removed. If you now re-start the computer you will be at Step
5 on page 3 of this document and can now re-install the software.
“Error code 10” during installation
This is caused by a failure to load the WinTV-HVR-3000 drivers.
Uninstall the software (as above) and then follow the instructions from
page 3. If this still gives you an error message move the WinTV-HVR3000 to a different PCI slot and re-install the drivers again.
Only some channels are found during DVB-T channel scan
Ensure that your antenna is capable of receiving Digital terrestrial
transmission (Most rooftop/loft antenna under 8 years old may work).
You can enter your postcode at this website address:
www.dtg.org.uk/retailer/coverage.html as this will show you what services are available in your area.
You can then enter your postcode at this website:
www.bbc.co.uk/reception/transmitters/today.shtml to see if there is
any engineering work being carried out on your transmitter as this
could affect the reception of some channels.
TV display has problems (e.g. no picture but with sound or blurred
image)
With the WinTV2000 application closed click on the WinTV program
group (Start / Programs / Hauppauge WinTV) there is a utility called
“Primary”. Set it to one of the other options and then close using the
“X” and restart the TV application. If the problem remains try another
option.
14. Troubleshooting
Radio Interference Statement:
The WinTV boards have been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and cause harmful
interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of
the following measures:
● reorient or relocate the receiving antenna.
● increase the separation between the equipment and receiver.
● connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
● consult the dealer or an experienced radio/TV technician for help.
FCC ID: H90WINTV
CAUTION: Changes or modifications not expressly approved by the
party responsible for compliance to the FCC Rules could void the
user's authority to operate the equipment.
CE Statement: This equipment has been tested and complies with EN
55013, EN 55020 and IEC 801-3 part 3 standards.
FCC Statement
The device may not be disposed of with household rubbish. This
appliance is labeled in accordance with European Directive
2002/96/EG concerning used electrical and electronic appliances
(Waste Electrical and Electronic Equipment - WEEE). The guideline
determines the framework for the return and recycling of used appliances as applicable throughout the EU. To return your used device,
please use the return and collection systems available to you.
Waste Electrical and Electronic Equipment
(WEEE)
does not begin with a number. You can use leading spaces to center
the name in the display. Hit Enter/Return to finish.
Minimize to tray; left click restores app, right click accesses context
menu
Content-Menu
If you click and hold the right hand mouse button on the Radio window
then a menu will appear.
Keyboard shortcuts
Key Function
F1-F10 Preset 1-10
Num 0,1-9 Preset 1-10
F11/12 Tune Up/Down as defined by Remote Tuning Mode
INS Add current station as preset if not already defined as preset
DEL Remove existing Preset
Pg Up/Dn Volume Up/Down
+/- Tune Up/Down
Home Seek Up
End Seek Down
Space Scan to next Preset or Station as defined in Scan Mode
O Toggle Mono/Stereo Mode
M Toggle Mute
N Minimize Radio
T Goto TV
C Goto CD Player
E Exit Radio (OFF)
S Toggle Scan Mode
R Toggle Mem state
Command line options for the WinTV32/WinTV2000 Application
To start the WinTV application with a specific command line option
you need to click on: Start / Run and type in:
“C:\Program\WinTV\WINTV2K.EXE”
You can now select some of the following options:
NoSplashScreen = -nss
WinTV32Mode = -nc
WinTV2000Mode = -cg
NoTipOfDay = -ntod
Suite = -sSuiteName
Channel = -cChannelNumber
WindowMode = -mMode ("tv", "NoTitle", "Title", or "Off" (all caseless)
(Note: ‘Off’ will cause an existing instance of the
WinTV app to exit)
13. WinTV Command line Parameter
Once these are set, click Set Program. You can add more Events, clikking Set Program after each event is set. When you are finished click
Close.
The WinTV program does not have to be running for the Scheduler to
work. If WinTV is not running, it takes about 10 seconds to start
Scheduler and to start the recording of TV.
You should see an icon close to
the Windows clock. You will reach
the menus of the 7 day EPG by a
right click on this icon. For more
information on its operation, visit www.hauppauge.co.uk
7 day EPG (for DVB-T)
Loading...