HATTORI KOGYO LG-600-100/150, LG-606T-100/150, LG-606-100, LG-606-150, LG-606T-100 Instruction Manual

...

IIIInnnnssssttttrrrruuuuccccttttiiiioooonnnn mmmmaaaannnnuuuuaaaall

GGGGaaaassss RRRRiiiicccceeee CCCCooooooookkkkeeeerr

MMMMooooddddeeeellll:::: LLLLGGGG----666600006666----111100000000////1111555500

LLLLGGGG----666600006666TTTT----111100000000////111155550000 ((((wwwwiiiitttthhhh aaaa pppprrrreeee----sssseeeetttt ttttiiiimmmmeeeerrrr))

))

Please read this manual carefully and follow instructions.

Please look after this manual.

CCCCoooonnnntttteeeennnnttttss

1. Cautions

2. Part names and specifications

3. How to cook delicious rice

4. Trouble indicators

5. Checking the combustion condition

6. Daily maintenance

7. Safekeeping

8. Troubleshooting

Hattori Kogyo K.K.

1111.... CCCCaaaauuuuttttiiiioooonnnnss

1. Check the gas you use

Use only type of gas listed on the equipment

Caution

Do not remodel the equipment.

Do not use other types of gas that arenÕt listed.

2. Installation

Requirements

Please follow these requirements. If you donÕt, it results in problems.

Items Requirements

Voltage AC 100V 10% 50/60 Hz

Temperature 5 60 shouldnÕt be frozen.

Humidity less than 90% shouldnÕt be dewing.

Ensure the equipment is installed level.

Tilted installation causes burning or uncooked rice.

You can check to see if itÕs level by using a small quantity

of water in the rice pan. It is level if the water is level.

You can also use a horizontal check.

Power supply outlet

Firmly plug a power supply cord behind the control box

into the outlet. An outlet with a breaker is ideal. Ensure

that you connect an earth cord from the power supply cord

without fail.

Notice: Do not connect the earth cord to the gas piping.

Keep out of water or oil

Do not install the equipment where it may be exposed to

water or oil. It may results in problems.

Do not block the exhaust outlets

Keep the equipment at least 150 mm(behind) and

200 mm(side) from the wall or other substances, even

if walls are inflammable.

Gas connection

Ask a local plumber for the gas piping connection.

Warning

Check that there is no gas leakage after gas

piping connection.

If you find any gas leakage;

Close the main gas cock immediately.

Check the gas connecting parts and repair.

Do not use matches or lighters, or you may cause an explosion.

Do not put objects such as fans or electrical appliances near the cooker. It may

cause sparks.

Open the window for ventilation.

Close the main gas cock after use.

2222.... PPPPaaaarrrrttttssss nnnnaaaammmmeeee aaaannnndddd ssssppppeeeecccciiiiffffiiiiccccaaaattttiiiioooonn

No. Name No. Name

1 Body 10 Burner

2 Front door 11 Thermo stand

3 Front door knob 12 Leg

4 Panel plate 13 Union connection

5 Control box 14 Insulation

6 Solenoid operated valve 15 Adjustment bolt

7 Governor 16 Damper

8 Nozzle 17 Power supply cord

9 Rice pan(with lid)

Specification

Model LG-606/606T-100 LG-606/606T-150

Spec. 2 decks 3 decks

Gas consumption 20.9kw(18,000kcal/h) 31.4kw(27,000kcal/h)

Power supply AC100V 50/60Hz AC100V 50/60Hz

Gas connection 20A 20A

Electric consumption 27W 40 W

3333.... HHHHoooowwww ttttoooo ccccooooooookkkk ddddeeeelllliiiicccciiiioooouuuussss rrrriiiiccccee

You can cook up to 7 kg per 1 rice pan. Be careful not to exceed the total amount of rice and

vegetables when you cook mixed rice.

1. Preparation

Washing

Wash the rice after taking out refuse or crushed rice.

It causes uncooked rice.

Pouring water and soaking

Put the washed rice and water (same amount of rice

or 1.1 times) into a rice pan and soak it for 40 minutes(summer) to 80 minutes(winter)

before you start cooking.

Adjust the quantity of water according to your taste.

Level the rice in a rice pan after pouring water.

2. Put the rice pan into the chamber.

Open the front door of the chamber and put the rice pan

on the front door guide rail. Push into the chamber.

3. Open the main gas cock.

warning: Be careful and avoid being burnt. The equipment is hot during and after cooking.

4. Cooking operation (Do not push the button too hard. It may cause problems or sheet

tearing)

Operation panel

LG-606 LG-606T

Indication

Plug the power supply cord into the outlet.

The model type is indicated and blinks. Power supply lamp lights.

Model indication LG-606 LG-606T

Push + button. Power supply lamp lights.

Cooking operation

Follow instructions listed below while leaving the front door open.

Push Cooking button. The Indicator indicates finish cooking temperature. (set at

125 )

LG-606 indicates last two figures

LG-606T (indicates set temperature)

Set the finish cooking temperature by pushing + or - buttons.

Refer to the cooking temperature table below. Temperature can be set from 100 to 150

by 5 increments.

Menu LG-606 LG-606T

Sushi rice 15 115

Plain rice 2 5 125

Mixed rice 3 5 135

Push Cooking button once to commence cooking.

Confirm the burner ignition then close the front door slowly.

Pre-set timer

Push the Pre-set button. Pre-set lamp will blink and indicate the pre-set time.

Set the time by pushing + or - buttons. Set the required time before cooking. Time

can be set from 30 min. to for 20h 30 min. by 30 min. increments.

Push the Cooking button.

Push the Cooking button. Pre-set and cooking lamps light and pre-set timer starts.

Pre-set time count down start.

If you want to cancel pre-set, after the pre-setting time, push the Pre-set button.

Pre-set lamp goes out and cancels.

5. During cooking

If you want to terminate the cooking process mid-way, push the Cooking button.

The burner flame will be extinguished and cooking will stop.

If you want to change the finish cooking temperature, change the temperature by pushing

+ or - buttons. Current finish cooking temperature is indicated.

You cannot change the temperature if you only have 1 minute or less left before finishing.

6. Completion of cooking

After cooking is over, the cooking lamp stops blinking stays alight. After 15 min. of steaming,

the lamp goes off.

7. ÒOidakiÓ (re-heating)

Follow instructions below while leaving a front door open.

Push the Cooking and - button at the same time. Cooking time (set value) is

indicated and cooking starts.

Push + or - buttons and set the re-heating time within 1 to 10 min.

Close the front door slowly.

8. Stirring of rice

When steaming is finished, stir the rice in order to

reduce excess steam and prevent rice from getting

cold and watery.

Warning

Be careful when handling rice pans not to get burnt, they are extremely hot after cooking.

9. Close the main gas cock after use.

About power cuts

Power cuts during cooking

Stop the cooking function and close the solenoid operated valve. After the electricity come

backs, the indicator will show the model used. (See # 3 Indication)

A power cut during pre-set

If the electricity comes back within one minute, the cooking function starts without any

problems.

If a power cut continues for more than one minute, the pre-set is canceled and the

indicator will show the model used. (See # 3 Indication)

Holding set functions

Finish cooking temperature program and pre-set time are held (memorized) even if the

power supply cord is unplugged

4444.... TTTTrrrroooouuuubbbblllleeee iiiinnnnddddiiiiccccaaaattttoooorr

The followings are trouble indicators. Please contact your local representative.

Indications Contents

E1 Extraordinal temperature (during cooking)

E2 Incomplete combustion or flame-out (during cooking)

E3 Para-fire (during ignition)

E4 Solenoid operated valve transistor short (during ignition)

E6 High-limit and cooking thermisters short circuit

E7 High-limit thermister short circuit

E8 Cooking thermister short circuit

E9 Excessively long cooking time ( over 60 min.)

By pushing the Cooking button, indication is released.

5555.... CCCChhhheeeecccckkkk tttthhhheeee ccccoooommmmbbbbuuuussssttttiiiioooonnnn ccccoooonnnnddddiiiittttiiiioooonn

1. Adjustment of the burner flame

Check the combustion condition from the looking

window. Adjust the flame till it becomes bluish.

Note) Always check the combustion condition.

Bad combustion flame causes low rice quality.

2. Examine burner holes

After use for a long time, burner holes become

clogged and the flame gets smaller. Clear clogged

holes by gimlet or similar tool.

6666.... DDDDaaaaiiiillllyyyy mmmmaaaaiiiinnnntttteeeennnnaaaannnnccccee

Daily care

Wipe off water thoroughly from rice pans and store them after use. Avoid rust.

Wipe off stains on outer frame by soft water soaked sponges or similar items.

Note: Do not wash the rice cooker using a hose. It causes electrical faults.

Maintenance

Beware of clogged burner holes. Clean them using a gimlet or similar tool.

Check if there are any cracks or rips in the power supply cord. It can cause short circuits

or electricity leakages. Contact your local representative. (Once a month)

Check the gas piping connection parts if there is any looseness. ( Once a month)

It causes gas leakage. Ask an expert for repairs.

7777.... SSSSaaaaffffeeeekkkkeeeeeeeeppppiiiinnnngggg IIIIffff nnnnooootttt iiiinnnn uuuusssseeee ffffoooorrrr eeeexxxxtttteeeennnnddddeeeedddd ppppeeeerrrriiiiooooddddss

Unplug the power supply cord from the outlet.

Close the main gas cock.

Clean stains and cover the equipment to avoid incoming of dust. Keep it in a well ventilated

place.

8888.... TTTTrrrroooouuuubbbblllleeeesssshhhhoooooooottttiiiinnnngg

In case of problems, solve or ask for repairs by following this list.

Condition Probable causes Solution

Electric power is off.

(power supply lamp doesnÕt

light)

Power supply cord is

unplugged.

Outlet is not charged with

electricity.

Fuse is cut.

Plug the cord in.

Check the main power supply.

Contact your local representative.

Main burner doesnÕt ignite. No ignition sparks. Make the distance between igniter

rod and burner 3 4 mm.

Adjust burner holes for ignition.

Check the electric discharge cord of

igniter.

If the electric discharge cord is torn

and the electricity discharges, tape it

with vinyl tape. Then contact your

local representative.

Main burner doesnÕt ignite

or goes out quickly.

Flame sensor doesnÕt hit

burner flame.

Flame sensor cord is cut.

Panel plate, solenoid

operated valve or other item

is out of order.

No gas.

Adjust the location of the flame rod

to hit the center of flame.

(Cut the power supply and adjust)

Repair the cut cord.

Contact your local representative

Open main gas cock

Cooking function is over

before rice is cooked or over

cooking occurs.

The setting time is

inappropriate.

Change the setting time after

judging room or water temperature.

Rice is too hard or too soft. Inadequate water

quantity.

Adjust the water quantity.

Rice is too sticky. Time for washing and

soaking is too long.

Steaming time insufficient.

Rice not stirred a fter

steaming.

Shorten the washing and soaking

time.

Take enough steaming time.

Release steam go by stirring rice.

Gas smell Gas leakage Close the main gas cock and contact

local gas company.

HATTORI KOGYO LG-600-100/150, LG-606T-100/150, LG-606-100, LG-606-150, LG-606T-100 Instruction Manual

Specifications and Main Features

Frequently Asked Questions

User Manual