8' HOT SHOT SKEEBALL TABLE
ASSEMBLY INSTRUCTIONS
NG2015
THANK YOU!
Thank you for purchasing this product.
We work around the clock and around the globe to ensure that our products
maintain the highest possible quality. However, in the rare instance that your
product is defective or missing parts, contact your retailer, or call 800-759-0977,
to submit parts requests or warranty claims. Please read the warranty
information at the back of these assembly instructions for further details.
IMPORTANT! PLEASE READ THESE ASSEMBLY INSTRUCTIONS IN
ENTIRETY BEFORE ASSEMBLING YOUR PRODUCT.
2
PARTS IDENTIFIER (NOT TO SCALE)
H1 - 1-1/4” Screw (36) H2 - 5/16” x 1-1/8”
Bolt (12)
H5 - 1/4” x 1” Bolt (4) H6 - 1/4” Washer (4) H7 - 1/4” Washer (8) H8 - 3/4” Screw (3)
H9 - 3/8” Screw (4) H10 - 1-1/4” Flat Screw (6) H11 - 1-1/2” Screw (3) H12 - 3/4” Flat Screw (4)
T1 - Allen Wrench (1)
H3 - 5/16” Washer (12)
H4 - 1/4” x 1-1/4”
Bolt (4)
P1L - Left Front Leg (1)
P6L - Left Front
Side Apron (1)
P1R - Right Front Leg (1) P2L - Left Middle Leg (1)
P3R - Right Back Leg (1)P3L - Left Back Leg (1)
P6R - Right Front
Side Apron (1)
P4 - Spreader (3) P5 - Front End Apron (1)
P7L - Left Back
Side Apron (1)
P2R - Right Middle Leg (1)
P7R - Right Back
Side Apron (1)
3
PARTS IDENTIFIER (NOT TO SCALE)
P8A - Crossbeam (1)
P11 - Back Upper
Panel (1)
P15 - Target
Board (1)
P8B - Crossbeam (2)
P12 - Back Bottom
Panel (1)
(Attaches to Side Apron)
P16 - Connect Hinge Set (2)
P9 - Front
Top Panel (1)
P13 - Back
Board (1)
P17 - Net (1)
P10 - Front
Bottom Panel (1)
P14 - Electronic
Scorer (1)
(Attaches to Side Apron)
Larger
P18 - Net Frame Front (1)
Smaller
P19 - Net Frame Back (1)
P22 - “L”Support Panel (1) P23 - Cover Panel (1)
P20 - Net Spacer Bar (2)
Please see Parts List at end of manual for part number when ordering parts.
For replacement parts please call 800-759-0977.
P21A - Support
Panel (1)
P21B - Support
Panel (1)
A1 - Ball (6)
4
ASSEMBLY TIPS
1. Find a clean, level surface to begin the assembly of your game table. The table will be
partially assembled upside down and then turned over onto its legs. This is a heavy game
and turning it over will require at least two strong adults.
2. Remove all of the contents from box and verify that you have all of the parts shown on
Note: Some parts may be pre-installed
or pre-assembled.
understand the text before beginning each assembly step.
4. When installing parts that have more than one screw or bolt, hand tighten all
5. Electric screwdrivers may be helpful during assembly; however, please set a low torque
and use extreme caution because screws may be stripped or overtightened, resulting in
damaged parts, if the electric screwdriver’s torque is set too high.
WARNINGS!
READ AND FOLLOW ALL ASSEMBLY, OPERATION AND SAFETY INSTRUCTIONS CAREFULLY.
CHOKE HAZARD - THIS TABLE CONTAINS SMALL BALLS AND PARTS
NOT SUITABLE FOR CHILDREN UNDER 3 YEARS OF AGE.
5
ASSEMBLY INSTRUCTIONS
1. Find a clean, level place to begin the assembly of your game. We recommend building the unit on the shipping carton to
protect the parts during assembly. Note: The two main units are assembled upside down then turned over for final assembly.
2. Attach the SUPPORT PANEL, P21B, to the FRONT BOTTOM PANEL, P10, using (2) SCREWS, H8, through the two
outer holes as shown in Figure 1. The middle hole will be used in a later step. Note: The P10 panel and P21B support
panel both have pre-drilled holes for screws.
H8
Unfinished Side Up
Black Side Down
P21B
P10
Figure 1
3. Place the LEFT FRONT SIDE APRON, P6L, and RIGHT FRONT SIDE APRON, P6R, upside down and approx. 2 feet
apart, as shown in Figure 2.
4. Insert FRONT TOP PANEL, P9, with finished white side down, into lower grooves of SIDE APRONS, P6L and P6R.
Make sure the end of P9 with the cutouts is on the same end as gear hinge as shown in Figure 2. Slide P9 forward until
the end with cutouts is flush with SIDE APRON ends above gear hinges. With help from another adult, hold this assembly
firmly and attach pieces together using (2) SCREWS, H1, and pre-drilled holes on each side.
5. Attach FRONT END APRON, P5, with groove facing in, using (2) SCREWS, H1, and pre-drilled holes on each side.
Note: Don’t tighten screws all the way until you complete Step 6. This will make it easier to get P10 into P5 groove.
6. Insert FRONT BOTTOM PANEL, P10, with unfinished side up, into upper grooves of SIDE APRONS, P6L and P6R.
Slide P10 forward until the end is flush with SIDE APRON ends above gear hinges, even with panel P9. Tighten P5 Screws.
P6R
P5
White
Side Down
Note: This unit is assembled
upside down.
Note: Location
of gear hinge
H1
P6L
H1
Note: Location
of gear hinge
Figure 2
Unfinished
Side Up
P9
Note: Location
of these cutouts
Slide both
panels in grooves
P10
6
ASSEMBLY INSTRUCTIONS (CONT.)
7. Attach CROSSBEAM, P8B, with cutout opening facing down and to the left, using (2) SCREWS, H1, and pre-drilled
holes on each side. Use (1) SCREW, H11, to attach center of crossbeam through P10 and into P21B, as shown in Figure 3.
8. Attach LEFT and RIGHT FRONT LEGS, P1L and P1R, using (2) BOLTS, H2, and (2) WASHERS, H3, on each leg, as
shown in Figure 3. Note: Hand tighten for now, and then do final tightening with ALLEN WRENCH, T1, once P4 Spreader
is attached in next step.
9. Attach SPREADER, P4, using (4) SCREWS, H1, as shown in figure 3. Note: Hand place screws in all four pre-drilled
holes to align panel before tightening.
CAUTION:
P4 SPREADER MUST BE CENTERED
CORRECTLY ONTO PRE-DRILLED HOLES
IN LEGS BEFORE ATTACHING WITH H1
P1R
SCREWS.
H1
Figure 3
P4
P1L
P8B
H11
H1
H3
H2
H1
NOTE: Location
of gear hinge
7
THANK YOU!ASSEMBLY INSTRUCTIONS (CONT.)
10. Attach the SUPPORT PANEL, P21A, to the FRONT BOTTOM PANEL, P10, using (1) SCREW, H8, through the
center hole as shown in Figure 4. The outer two holes will be used in a later step. Note: The P12 panel and P21A support
panel both have pre-drilled holes for screws.
H8
P12
Figure 4
11. Place the LEFT BACK SIDE APRON, P7L, and RIGHT BACK SIDE APRON, P7R, upside down and approx. 2 feet
apart, as shown in Figure 5.
12. Insert BACK TOP PANEL, P11, with finished white side down, into lower grooves of SIDE APRONS, P7L and P7R.
Make sure the end of P11 with the cutouts is on the same end as gear hinge as shown in Figure 5. Slide P11 forward until
the end with cutout is flush with SIDE APRON ends above gear hinges. With help from another adult, hold this assembly
firmly and attach pieces together using (3) SCREWS, H1, and pre-drilled holes on each side.
13. Insert BACK BOTTOM PANEL, P12, with unfinished side up, into upper grooves of SIDE APRONS, P7L and P7R.
Slide P12 forward until the end is flush with SIDE APRON ends above gear hinges, even with panel P11.
P12
P21A
P7L
Note: This unit is assembled
upside down.
Unfinished Side Up
Black Side Down
P7R
H1
Figure 5
Slide both
panels in grooves
Note: Location
of gear hinge
Unfinished
Side Up
White
P11
Side Down
H1
Note: Location
of these cutouts
8
ASSEMBLY INSTRUCTIONS (CONT.)
14. Attach CROSSBEAMS, P8A and P8B, with cutout openings facing down and to the right, using (2) SCREWS, H1, and
pre-drilled holes on each side. Use (1) SCREW, H11, to attach center of CROSSBEAM, P8B, through P12 and into P21A,
assembled in Step 10. Note: Cutouts used as wiring guides in future step. See Figure 6 for correct locations of P8A and P8B.
15. Assemble LEFT and RIGHT MIDDLE LEGS, P2L and P2R, together with SPREADER, P4, using (4) SCREWS, H1,
as shown in Figure 6. Note: Hand place screws in all four pre-drilled holes to align panel before tightening. Attach “L”
SUPPORT PANEL, P22, in same manner using (6) SCREWS, H10, as shown.
16. Attach Middle Leg Assembly between assembled sides, P7L and P7R, using (2) BOLTS, H2, and (2) WASHERS, H3,
on each leg, as shown in Figure 6. Attach “L” SUPPORT PANEL, P22, to table using SCREW, H11, in middle pre-drilled
hole. Note: Velcro will be used as wire harness in future step.
17. Attach LEFT and RIGHT BACK LEGS, P3L and P3R, using (2) BOLTS, H2, and (2) WASHERS, H3, on each leg, as
shown in Figure 4. Note: Hand tighten for now, and then do final tightening with ALLEN WRENCH, T1, once P4 Spreader
is attached in next step.
18. Attach SPREADER, P4, between Legs using (4) SCREWS, H1, as shown in figure 6.
Note: Hand place screws in all four pre-drilled holes to align panel before tightening.
P4
P2R
P2L
H3
H1
P22
H10
H1
P3R
P4
CAUTION:
P4 SPREADER MUST BE CENTERED
CORRECTLY ONTO PRE-DRILLED HOLES
IN LEGS BEFORE ATTACHING WITH H1
SCREWS.
P3L
P8A
H11
H2
Figure 6
H1
P8B
H2 H3
P22
Velcro
Note: Correct location
of Support Panel to Legs
9
ASSEMBLY INSTRUCTIONS (CONT.)
19. With the help of another adult, set both completed assemblies upright and position so gears face each other as shown
in Figure 7. Using (2) HINGE SETS, P16, connect assemblies using BOLT, H5, and Washer, H7, as shown in Figure 7.
The bolts should be snug, but NOT over tightened as this is a pivot area. Note: Hinge gear assemblies must mesh together,
per diagram, and there should be no gap between playfields. Also, only one hinge plate per set is threaded and must be
installed on the inside of each playfield side.
20. Place TARGET BOARD, P15, with red hole at the top, into position with the sides resting in the grooves of the braces
on the side panels and against the front of the ramp.
21. Attach the RESET BUTTON, with the long white wire, through the hole in the FRONT END APRON, P5, by removing
the washer and nut on the back of the Reset Button, feeding the Reset Button and wire through the hole from the front and
re-attaching the washer and nut. Note: Be careful not to damage or break wire connections while attaching Reset Button.
P15
Note: This Hinge is Threaded and Must Be on Inside
Note: This Hinge is NOT Threaded
and Must Be on Outside
H5 Bolt
Reset Button (this ships
pre-wired to
Target Board)
Bundle of
White Wire
P7R
Back Side
Apron
P16
Hinge Set
H7
Washer
Ligature
Figure 7
No Gap
CAUTION:
Pinch Point
Note: Hinge Gear Assemblies Must Mesh
P16
Hinge Set
No Gap
P6R
Front Side
Apron
H7
Washer
CAUTION:
Pinch Point
P5
Reset Button
P5
Reset
Button
10
ASSEMBLY INSTRUCTIONS (CONT.)
22. Feed the long white wire through the cutouts in all CROSSBEAMS, P8A and P8B, and the Velcro on P22, toward the
back and up through the hole in the BACK BOTTOM PANEL, P12. This will connect to the short white wire on the wiring
harness.
23. Feed the Target Board’s Wiring Harness through the round hole in the BACKBOARD, P13, and attach the Backboard
between the SIDE APRONS using (4) SCREWS, H1, as shown in figure 8. Note: Hand place screws in all four pre-drilled
holes to align panel before tightening.
24. Attach ELECTRONIC SCORER, P14, to Backboard using (4) SCREWS, H9, as shown. Connect the Wiring Harness
from the Electronic Scorer to the Target Board’s Wiring Harness.
25. Attach COVER PANEL, P23, over Wiring Harness and to Backboard using (4) SCREWS, H12, as shown in Figure 8.
26. Insert 4 AA batteries (not included) into back of Electronic Scorer. Note: this game does NOT come with an AC adapter.
Remove protective plastic film from face of Electronic Scorer.
P14
H9
H12
P23
Figure 8
P13
H1
11
ASSEMBLY INSTRUCTIONS (CONT.)
27. Loosely attach NET FRAME FRONT, P18, and NET FRONT BACK, P19, to the Back Side Aprons using (4) BOLTS,
H4, and WASHERS, H6, through the eye hole at the bottom of the frames.
28. Attach (2) NET SPACER BARS, P20, between the Front and Back Frames, on either side, by inserting the curved
ends into the frame receptacle as shown in Figure 9.
29. Drape the NET, P17, over the frame with the longest side, and corner rivets, running side to side. The net will angle
down toward the front. Now remove Bolts loosely attached in Step 27, one at a time, and re-insert Bolt through Corner
Rivets and back through Frame Eye Hole until all four are securely attached. Use Velcro on Net to secure Net to Frame.
P20
Spacer Bars
P19
Frame
H4
H6
Back
(Smaller)
P17
Net
P18
Frame
Front
(Larger)
H4
Figure 9
H4
H6
FINAL SET-UP & HOW TO PLAY
1. Using two adults, set the unit in a suitable location in your game room.
2. Install four (4) “AA” batteries (not included) into the backside of the Electronic Scorer, P14.
3. Turn the power switch to the ON position.
4. When all “zeroes” are showing on the score board, press the reset button on the front of the
unit. You are now ready to play.
5. Each player rolls six (6) balls per game trying to reach the highest score. If a ball is rolled
and it doesn’t score, you may roll that ball again. The player with the highest score wins.
6. After both players have rolled their six balls, press the Reset Button to play again.
7. Turn the power OFF when not in use.
CAUTION: DO NOT THROW the ball at the target board as this may cause damage to the
game. The correct and safe way is to always ROLL the ball along the runway.
12
CONGRATULATIONS!
You have now assembled your Game Table.
Please note the Care and Use instructions below to
ensure years of trouble free use of your game table.
1. This product is intended for INDOOR use only.
2. Do NOT sit, climb or lean on the table.
3. Do NOT drag the table when moving it as this will damage the legs.
CARE AND USE
13
180-DAY LIMITED WARRANTY
This product is warranted to the original purchaser to be free from defects in material or workmanship
for a period of 180 days from the date of the original retail purchase.
This warranty does not cover defects or damage due to improper installation, alteration, accident or
any other event beyond the control of the manufacturer. Defects or damage resulting from misuse,
abuse or negligence will void this warranty. This warranty does not cover scratching or damage that
may result from normal usage.
This product is not intended for institutional or commercial use; the manufacturer does not assume
any liability for such use. Institutional or commercial use will void this warranty.
This warranty is nontransferable and is expressly limited to the repair or replacement of the defective
product. During the warranty period, the manufacturer shall repair or replace defective parts at no
cost to the purchaser. Shipping charges and insurance are not covered and are the responsibility of
the purchaser. Labor charges and related expenses for removal, installation or replacement of the
product or components are not covered under this warranty.
The manufacturer reserves the right to make substitutions to warranty claims if parts are unavailable
or obsolete.
The manufacturer shall not be liable for loss of use of the product or other consequential or incidental
costs, expenses or damages incurred by the consumer of any other use. The user assumes all risk of
injury resulting from the use of this product.
This warranty is expressly in lieu of all other warranties, expressed or implied, including warranties of
. Neither the manufac-
turer nor any of its representatives assumes any other liability in connection with this product.
All warranty claims must be made through the retailer where the product was originally
purchased. A purchase receipt or other proof of date of purchase will be required to process
all warranty claims. The model number and part numbers found within the assembly
instructions will be required when submitting any parts requests or warranty claims.
For further warranty information or inquiries, please call 800-759-0977
14
8’ HOT SHOT SKEEBALL TABLE - NG2015
Parts List
PARTS
P7L
P23
P19
P3L
P14
P4
P13
P20
P17
P18
P15
P3R
P11
P7R
A1
P16
P2R
P6R
P9
P10
P1R
P6L
P1L
RIGHT MIDDLE
LEG
P4
LEFT BACK LEG
P5
RIGHT BACK
LEG
P1L NGP5856
LEFT FRONT LEG
P2L
P1R NGP5857 P2L NGP5858 P2R NGP5859 P3L NGP5860 P3R NGP5861 P4 NGP5862
RIGHT FRONT
LEG
LEFT MIDDLE
LEG
P5 NGP5863 P6L NGP5864 P6R NGP5865 P7L NGP5866 P7R NGP5867 P8A NGP5868
FRONT END
APRION
P9 NGP5870
FRONT TOP
PANEL
P16 NGP5877
LEFT FRONT
SIDE APRON
RIGHT FRONT
SIDE APRON
LEFT BACK
SIDE APRON
P10 NGP5871 P11 NGP5872 P12 NGP5873
FRONT BOTTOM
PANEL
BACK UPPER
PANEL
BACK BOTTOM
PANEL
P17 NGP5878 P18 NGP5879 P19 NGP5880
RIGHT BACK
SIDE APRON
P13 NGP5874
BACKBOARD
P20 NGP5881
CROSSBEAM
P14 NGP5875
ELECTRONIC
SCORER
SPREADER
P8B NGP5869
CROSSBEAM
P15 NGP5876
TARGET BOARD
P21B NGP5883P21A NGP5882
CONNECT HINGE
SET
P22 NGP5884
“L” SUPPORT
PANEL
NET
NET FRAME
FRONT
P23 NGP5885 A1 NGP5886
COVER PANEL
BALL
NET FRAME
BACK
NGP5888
RUBBER
GEAR HINGE
NET SPACER
BAR
NGP5890
RESET BUTTON
SUPPORT PANEL
SUPPORT PANEL
11/13
HARDWARE PACK - NGP5887
H1 H2 H3 H4 H5 H6
1-1/4” SCREW
H8
3/4” SCREW
5/16” BOLT
H9
3/8” SCREW
5/16” WASHER
1/4”X1-1/4” BOLT
H10 H11 H12 T1
1-1/4” FLAT
SCREW
1-1/2” SCREW
1/4”X1” BOLT
3/4” FLAT
SCREW
ALLEN WRENCH
1/4” FLAT
WASHER
H7
1/4” FLAT
WAS HER
ADDITIONAL EQUIPMENT
REQUIRED:
PHILLIPS HEAD
SCREWDRIVER
9/13
Loading...