Hatco LFST-48 Series Installation Manual

FLAV-R-SAVOR

®

Large Capacity Holding Cabinet

LFST-48 Series

Installation & Operating Manual

I&W #07.05.186.00

This manual contains important safety information
concerning the maintenance, use and operation of this
product. Failure to follow the instructions contained in
this manual may result in serious injury. If you’re unable
to understand the contents of this manual, please bring
it to the attention of your supervisor. Do not operate this
equipment unless you have read and understood the
contents of this manual.

Este manual contiene importante información sobre
seguridad concerniente al mantenimiento, uso y
operación de este producto. Cualquier falla en el
seguimiento de las instrucciones contenidas en este
manual puede resultar en un serio daño. Si usted no
puede entender el contenido de este manual por favor
pregunte a su supervisor. No opere este equipo al
menos que haya leído y comprendido el contenido de
este manual.

CONTENT

Form No. LFSTM-0807

i

Important Owner Information...............................i

Introduction ...........................................................i

Important Safety Information..............................1

Model Description................................................3

Model Designation ...............................................3

Specifications.......................................................4

Electrical Rating Chart ....................................4

Plug Configuration...........................................4

Overall Dimensions .........................................4

Cabinet Opening Dimensions .........................4

Rack Dimensions ............................................4

Installation ............................................................5

Unpacking .......................................................5

Location...........................................................6

Operation ..............................................................6

Maintenance .........................................................7

General............................................................7

Cleaning ..........................................................7

Light Bulb Replacement ..................................7

Troubleshooting...................................................8

Hatco Limited Warranty.......................................9

Authorized Parts Distributors ............Back Cover

Record the model number, serial number (located on
the side of the unit), voltage and purchase date of
your Flav-R-Savor®Large Capacity Holding Cabinet
in the spaces below. Please have this information
available when calling Hatco for service assistance.

Model No. ________________________________

Serial No. ________________________________

Voltage __________________________________

Date of Purchase __________________________

Business 8:00 a.m. to 5:00 p.m.
Hours: Central Standard Time

(Summer Hours: June to September –
8:00 a.m. to 5:00 p.m. C.S.T.
Monday through Thursday
8:00 a.m. to 2:30 p.m. C.S.T. Friday)

Telephone: [phone]

Fax: [phone] (Parts & Service)

[phone] (International)

24-Hour 7-Day Parts & Service
Assistance available in the United
States and Canada by calling
[phone].

Additional information can be found by visiting our
web site at www.hatcocorp.com

The Hatco Flav-R-Savor Large Capacity Holding
Cabinet is designed to hold prepared foods for
prolonged periods of time while maintaining that
“just-made” quality.

Hatco Large Capacity Holding Cabinets provide the
best environment for wrapped foods and
sandwiches by regulating the air temperature.

Flav-R-Savor air flow pattern is designed to maintain
consistent cabinet temperature. The left and right
side heat sources create a “blanket” effect around
the food. The air flow rate enables the cabinet to
rapidly recover temperature after opening and
closing the door.

Front and rear access doors and adjustable shelves
make the Hatco Flav-R-Savor Large Capacity Holding
Cabinet perfect for any food service application.

This manual provides the installation, safety and
operating information for the Flav-R-Savor Large

Capacity Holding Cabinet. We recommend all
installation, operating and safety information
appearing in this manual be read prior to installation or
operation of your Hatco Large Capacity Holding
Cabinet. Safety information that appears in this
manual after a warning symbol and the words
WARNING or CAUTION printed in bold face are
very important. Warning means there is the
possibility of serious personal injury or death to
yourself or others. Caution means there is the
possibility of minor or moderate injury. NOTICE
signifies the possibility of equipment or property
damage only.

Your Large Capacity Holding Cabinet is a product of
extensive research and field testing. The materials
used were selected for maximum durability,
attractive appearance and optimum performance.
Every unit is thoroughly inspected and tested prior to
shipment.

IMPORTANT OWNER INFORMATION

INTRODUCTION

IMPORTANT SAFETY INFORMATION

Form No. LFSTM-0807

1

WARNINGS

To assure safe and proper operation, plug
unit into a properly grounded electrical
outlet of the correct voltage, size and plug
configuration. If the plug and receptacle do
not match, contact a qualified electrician to
determine the proper voltage and size and
install the proper electrical outlet.

For safe and proper operation, the unit must
be located a minimum of 1" (25.4 mm) from
combustible walls and materials. If safe
distances are not maintained, discoloration
or combustion could occur.

Some exterior surfaces on the unit will get
hot. Use caution when touching these areas
to avoid injury.

To prevent any injury or damage to the unit
do not pull unit by power cord.

To prevent any injury, discontinue use if
power cord is frayed or worn.

To avoid any injury, turn the power switch
OFF, unplug the unit from the power source
and allow to cool completely before
performing any maintenance or cleaning.

To avoid electrical shock or personal injury,
do not steam clean or use excessive water
on the unit.

To avoid electrical shock or personal injury,
DO NOT submerge in water. Unit is not
waterproof. Do not operate if it has been
submerged in water.

WARNINGS

Only light bulbs which meet or exceed NSF
standards, specifically designed for food
holding areas must be used. Breakage of
light bulbs not specially coated or covered
could result in personal injury and/or food
contamination.

If service is required on this unit, contact
your Authorized Hatco Service Agent, or
contact the Hatco Service Department at
800-558-0607 or 414-671-6350; fax 800-690­2966 or International fax [phone].

This product has no “user” serviceable
parts. To avoid damage to the unit or injury
to personnel, use only Authorized Hatco
Service Agents and Genuine Hatco Parts
when service is required.

Genuine Hatco Replacement Parts are
specified to operate safely in the
environments in which they are used. Some
aftermarket or generic replacement parts do
not have the characteristics that will allow
them to operate safely in Hatco equipment.
It is essential to use Hatco Replacement
Parts when repairing Hatco equipment.
Failure to use Hatco Replacement Parts may
subject operators of the equipment to
hazardous electrical voltage, resulting in
electrical shock or burn.

IMPORTANT! Read the following important safety information to avoid personal injury or
death, and to avoid damage to the equipment or property.

IMPORTANT SAFETY INFORMATION

Form No. LFSTM-0807

2

CAUTIONS

To avoid any injury or damage, locate the
Large Capacity Holding Cabinet at the
proper counter height, in an area that is
convenient for use. The location should be
level to prevent the unit or its contents from
accidentally falling, and strong enough to
support the weight of the unit and food.

Unit is not weatherproof. For safe and
proper operation the unit must be located
indoors where the ambient air temperature
is a minimum of 70°F (21°C) and a maximum
of 85°F (29°C).

NOTICE

Use only non-abrasive cleaners. Abrasive
cleaners could scratch the finish of your
unit marring its appearance and making it
susceptible to soil accumulation.

IMPORTANT! Read the following important safety information to avoid personal injury or
death, and to avoid damage to the equipment or property.

ALL MODELS

Flav-R-Savor®Large Capacity Holding Cabinets are
standard in black or any of five other optional
Designer colors. Painted surfaces are powder­coated painted steel and aluminum. Cabinet
contains four tempered glass doors for easy access
and visibility from front or back. Cabinet sides are
tempered glass for good visibility and heat retention.
Cabinet interior top and bottom are made of easy-to­clean stainless steel. Dual heaters and fans create a
dry heat system that is suitable for all boxed or
wrapped food products.

The three shelves have product stops and are
inclined toward the service area for excellent product
visibility. Cabinet has incandescent lighting to
heighten product awareness.

MODEL DESCRIPTION

Form No. LFSTM-0807

3

Figure 1. Model LFST-48

Figure 2. Model Designation

L FS T - 48

MODEL DESIGNATION

Large

Flav-R-Savor

Tall

Width (Inches)

PLUG CONFIGURATION

Units are supplied from the factory with a 6'
(1829 mm) electrical cord and NEMA L14-20P plug
installed. (See Figure 3.)

WARNING
To assure safe and proper operation, plug unit
into a properly grounded electrical outlet of the
correct voltage, size and plug configuration. If
the plug and receptacle do not match, contact a
qualified electrician to determine the proper
voltage and size and install the proper electrical
outlet.

Form No. LFSTM-0807

4

SPECIFICATIONS

ELECTRICAL RATING CHART

Model Voltage Watts Amps Plug Configuration/Wiring Shipping Weight

LFST-48 120/208 2150 14.6 NEMA L14-20P 190 lbs (86 kg)

LFST-48 120/240 2150 14.6 NEMA L14-20P 190 lbs (86 kg)

Figure 3. Plug Configuration

*

Receptacle not supplied by Hatco.

Figure 4. Dimensions

NEMA L14-20P

30"

(762 mm)

47-11/16" (1211 mm)

27-1/8" (689 mm)

OVERALL DIMENSIONS

*

48-7/8" (1241 mm)

24-1/4" (616 mm)

CABINET OPENING DIMENSIONS

42-7/8" (1089 mm) x 21-7/8" (556 mm)

RACK DIMENSIONS

A chrome-plated three-shelf rack is included to hold
and display the wrapped foods. Shelves are slanted
on the wire rack.

Rack Rack Rack

Width Depth Height

42-1/4" 17-1/2" 21-1/4"

(1073 mm) (445 mm) (540 mm)

Figure 5. Rack with Three Shelves

UNPACKING

The Flav-R-Savor® Large Capacity Holding Cabinet
is shipped with most components installed and ready
for operation. The following installation instructions
must be performed before plugging in and operating
the cabinet.

WARNING
To prevent any injury or damage to the unit, do
not pull unit by power cord.

1. Remove unit from box. Two people are required.

2. Remove information packet. To prevent delay in
obtaining warranty coverage, fill out and mail in
the warranty card.

3. Remove tape and protective film from all surfaces
of unit.

4. The stainless steel floor in all units is protected
during shipping with a sheet of corrugated
cardboard. This protection must be removed prior
to cabinet operation.

5. The shelves have packing material and
cardboard attached for protection during
shipping. This protection must be removed prior
to cabinet operation.

6. When placing shelf rack inside the cabinet, rods
on bottom of rack must be inside floor pins. (See
Figure 6.)

7. When installing wire shelves, set directly on top
of rack shelf pins. Insert shelves with
reinforcement to the front. (See Figure 6.)

8. Cabinet comes with sign holders attached on all
four sides, with clear plastic inserts. Signs not
included. (See Figure 7).

Figure 6. Shelf Rack and Floor Pins (Back View)

Figure 6. Shelf Rack and Floor Pins (Back View)

INSTALLATION

Form No. LFSTM-0807

5

Rack
Shelf
Pin

Locate rods on bottom
rack inside floor pins

Locate rack side walls
outside floor pins

Floor Pin

Sign Dimensions

Control Side

3-1/2" (89 mm) high x 31-15/16" (811 mm) wide

Customer Side

3-1/2" (89 mm) high x 45" (1143 mm) wide

Ends

3-1/2" (89 mm) high x 22-5/8" (575 mm) wide

INSTALLATION (CONTINUED)

Form No. LFSTM-0807

6

WARNING
Some exterior surfaces on the unit will get hot.
Use caution when touching these areas to avoid
injury.

WARNING
To prevent any injury, discontinue use if power
cord is frayed or worn.

CAUTION
Unit is not weatherproof. For safe and proper
operation the unit must be located indoors
where the ambient air temperature is a minimum
of 70°F (21°C) and a maximum of 85°F (29°C).

1. Plug unit into an electrical outlet of the correct
voltage, size and plug configuration. See
SPECIFICATIONS for details.

2. Turn the Power Switch on the control panel to the
ON position. (See Figure 9).

3. To set the temperature, turn the red Mode Switch
counterclockwise to the SP-1 position indicated
on the controller.

4. Adjust the Setpoint Screw to the desired
temperature.

5. Turn the red Mode Switch to the TEMP position.
The cabinet temperature range is room
temperature to 180°F.

6. Allow 20 to 30 minutes for unit to reach operating
temperature.

Figure 9. Control Panel

TEMP.

F

SP1

Power
Switch

Setpoint

Screw

Mode Switch

OPERATION

9. Install door handles to top of doors on front and
back of cabinet, using the screws supplied.
(See Figure 8.)

LOCATION

WARNING
For safe and proper operation, the unit must be
located a minimum of 1" (25 mm) from
combustible walls and materials. If safe distances
are not maintained, discoloration or combustion
could occur.

CAUTION
To avoid any injury or damage, locate the Large
Capacity Holding Cabinet at the proper counter
height, in an area that is convenient for use. The
location should be level to prevent the unit or its
contents from accidentally falling, and strong
enough to support the weight of the unit and food.

NOTE: The unit must be transported in the upright
position.

Figure 8. Door Handle Installation

MAINTENANCE

Form No. LFSTM-0807

7

GENERAL

The Hatco Flav-R-Savor Large Capacity Holding
Cabinet is designed for maximum durability and
performance, with minimum maintenance.

WARNING
To avoid any injury, turn the power switch OFF,
unplug the unit from the power source and allow
to cool completely before performing any
maintenance or cleaning.

CLEANING

WARNING
To avoid electrical shock or personal injury, do
not steam clean or use excessive water on the
unit.

WARNING
To avoid electrical shock or personal injury, DO
NOT submerge in water. Unit is not waterproof.
Do not operate if it has been submerged in water.

To preserve the finish of the Flav-R-Savor Large
Capacity Holding Cabinet, it is recommended that
the exterior and interior surfaces be wiped daily with
a damp cloth. Hard to reach areas should be
cleaned with a small brush and mild soap.

Shelves should be removed and washed. Stubborn
stains should be removed from the shelves with a
good stainless steel cleaner or a non-abrasive
cleaner.

NOTICE
Use only non-abrasive cleaners. Abrasive
cleaners could scratch the finish of your unit
marring its appearance and making it
susceptible to soil accumulation.

Clean the glass sides using a common glass
cleaner. In almost all cases, glass panels should be
cleaned while remaining in the unit.

LIGHT BULB REPLACEMENT

The display lights are shatter-resistant incandescent
light bulbs which illuminate the warming area. These
bulbs have a special coating to guard against injury
and food contamination in the event of breakage.

1. To replace a bulb, disconnect the power supply
from the unit and wait until the unit has cooled.

2. Bulbs have a threaded base. Unscrew the light
bulb from the unit and replace it with a new
specially coated incandescent bulb.

NOTE: Hatco shatter-resistant light bulbs meet NSF
standards for food holding and display areas. For
120/280 and 120/240 volt applications, use Hatco
part #02.30.043.00.

WARNING
Only light bulbs which meet or exceed NSF
standards, specifically designed for food
holding areas, must be used. Breakage of light
bulbs not specially coated or covered could
result in personal injury and/or food
contamination.

WARNING
If service is required on this unit, contact your
Authorized Hatco Service Agent, or contact the
Hatco Service Department at 800-558-0607 or
414-671-6350; fax [phone] or International
fax [phone].

WARNING
This product has no “user” serviceable parts. To
avoid damage to the unit or injury to personnel,
use only Authorized Hatco Service Agents and
Genuine Hatco Parts when service is required.

WARNING
Genuine Hatco Replacement Parts are specified
to operate safely in the environments in which
they are used. Some aftermarket or generic
replacement parts do not have the
characteristics that will allow them to operate
safely in Hatco equipment. It is essential to use
Hatco Replacement Parts when repairing Hatco
equipment. Failure to use Hatco Replacement
Parts may subject operators of the equipment to
hazardous electrical voltage, resulting in
electrical shock or burn.

TROUBLESHOOTING

Form No. LFSTM-0807

8

WARNINGS

To avoid any injury, turn the power switch OFF,
unplug the unit from the power source and allow
to cool completely before performing any
maintenance or cleaning.

WARNINGS

This product has no “user” serviceable parts. To
avoid damage to the unit or injury to personnel,
use only Authorized Hatco Service Agents and
Genuine Hatco Parts when service is required.

SYMPTOM PROBABLE CAUSE CORRECTIVE ACTION

Light bulb not working. Light bulb defective.

Power turned OFF.

Replace light bulb.

Turn unit ON.

Food cavity not hot enough. Temperature control set too low.

Heating element(s) not working.

Temperature control not working
properly.

Air circulating fan not working
properly.

Adjust temperature control to a
higher setting.

Contact Authorized Service
Agent or Hatco for assistance.

Contact Authorized Service
Agent or Hatco for assistance.

Contact Authorized Service
Agent or Hatco for assistance.

Food cavity too hot. Temperature control set too high.

Temperature control not working
properly.

Adjust temperature control to a
lower setting.

Contact Authorized Service
Agent or Hatco for assistance.

No heat, but light works. Temperature control set too low.

Heating element(s) not working.

Temperature control not working
properly.

Adjust temperature control to a
higher setting.

Contact Authorized Service
Agent or Hatco for assistance.

Contact Authorized Service
Agent or Hatco for assistance.

No heat and no light. Unit turned OFF.

Circuit breaker tripped.

Turn unit ON.

Reset circuit breaker. If circuit
breaker continues to trip contact
Authorized Service Agent or
Hatco for assistance.

Form No. LFSTM-0807

9

HATCO LIMITED WARRANTY

1. PRODUCT WARRANTY

Hatco warrants the products that it manufactures
(the “Products”) to be free from defects in materials
and workmanship, under normal use and service, for
a period of one (1) year from the date of purchase
when installed and maintained in accordance with
Hatco’s written instructions or 18 months from the
date of shipment from Hatco. Buyer must establish
the product’s purchase date by returning Hatco’s
Warranty Registration Card or by other means
satisfactory to Hatco in its sole discretion.

Hatco warrants the following Product components to
be free from defects in materials and workmanship
from the date of purchase (subject to the foregoing
conditions) for the period(s) of time and on the
conditions listed below:

a) One (1) Year Parts and Labor PLUS One (1)

Additional Year Parts-Only Warranty:

Toaster Elements (metal sheathed)
Drawer Warmer Elements (metal sheathed)
Drawer Warmer Drawer Rollers and Slides
Food Warmer Elements (metal sheathed)
Display Warmer Elements (metal sheathed
air heating)
Holding Cabinet Elements (metal sheathed
air heating)

b) One (1) Year Parts and Labor PLUS Four

(4) Years Parts-Only Warranty on pro-rated
terms that Hatco will explain at Buyer’s
request:

3CS and FR Tanks

c) One (1) Year Parts and Labor PLUS Nine

(9) Years Parts-Only Warranty on:

Electric Booster Heater Tanks
Gas Booster Heater Tanks

THE FOREGOING WARRANTIES ARE EXCLUSIVE
AND IN LIEU OF ANY OTHER WARRANTY,
EXPRESSED OR IMPLIED, INCLUDING BUT NOT
LIMITED TO ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE OR PATENT OR
OTHER INTELLECTUAL PROPERTY RIGHT
INFRINGEMENT. Without limiting the generality of
the foregoing, SUCH WARRANTIES DO NOT
COVER: Coated incandescent light bulbs,
fluorescent lights, lamp warmer heat bulbs, glass
components, Product failure in booster tank, fin tube
heat exchanger, or other water heating equipment,
caused by liming, sediment buildup, chemical attack
or freezing, Product misuse, tampering or
misapplication, improper installation or application of
improper voltage.

2.LIMITATION OF REMEDIES AND
DAMAGES

Hatco’s liability and Buyer’s exclusive remedy
hereunder will be limited solely, at Hatco’s option, to
repair or replacement by a Hatco-authorized service
agency (other than where Buyer is located outside of
the United States, Canada, United Kingdom or
Australia in which case Hatco’s liability and Buyer’s
exclusive remedy hereunder will be limited solely to
replacement of part under warranty) with respect to
any claim made within the applicable warranty
period referred to above. Hatco reserves the right to
accept or reject any such claim in whole or in part.
Hatco will not accept the return of any Product
without prior written approval from Hatco, and all
such approved returns shall be made at Buyer’s sole
expense. HATCO WILL NOT BE LIABLE, UNDER
ANY CIRCUMSTANCES, FOR CONSEQUENTIAL
OR INCIDENTAL DAMAGES, INCLUDING BUT
NOT LIMITED TO LABOR COSTS OR LOST
PROFITS RESULTING FROM THE USE OF OR
INABILITY TO USE THE PRODUCTS OR FROM
THE PRODUCTS BEING INCORPORATED IN OR
BECOMING A COMPONENT OF ANY OTHER
PRODUCT OR GOODS.

HATCO CORPORATION

P.O. Box 340500, Milwaukee, WI 53234-0500 U.S.A.

[phone] [phone]

Parts & Service Fax [phone] Int’l. Fax [phone]

www.hatcocorp.com

HATCO AUTHORIZED PARTS DISTRIBUTORS

Printed in U.S.A. August 2007 Part No. 07.04.417.00 Form No. LFSTM-0807

ALABAMA

Jones McLeod Appl. Svc.
Birmingham 205-251-0159

ARIZONA

Auth. Comm. Food Equip.
Phoenix 602-234-2443

Byassee Equipment Co.
Phoenix 602-252-0402

CALIFORNIA

Industrial Electric
Commercial Parts & Service, Inc.
Huntington Beach 714-379-7100

Chapman Appl. Service
San Diego 619-298-7106

P & D Appliance
Commercial Parts & Service, Inc.
S. San Francisco 650-635-1900

COLORADO

Hawkins Commercial Appliance
Englewood 303-781-5548

FLORIDA

Whaley Foodservice Repair
Jacksonville 904-725-7800

Nass Service Co., Inc.
Orlando 407-425-2681

B.G.S.I.
Pompano Beach 954-971-0456

Comm. Appliance Service
Tampa 813-663-0313

GEORGIA

TWC Services
Smyrna 770-438-9797

Heritage Service Group
Norcross 866-388-9837

Southeastern Rest. Svc.
Norcross 770-446-6177

HAWAII

Burney’s Comm. Service, Inc.
Honolulu 808-848-1466

Food Equip Parts & Service
Honolulu 808-847-4871

ILLINOIS

Parts Town
Lombard 708-865-7278

Eichenauer Elec. Service
Decatur 217-429-4229

Midwest Elec. Appl. Service
Elmhurst 630-279-8000

Cone’s Repair Service
Moline 309-797-5323

INDIANA

GCS Service
Indianapolis 317-545-9655

IOWA

Electric Motor Service Co.
Davenport 319-323-1823

Goodwin Tucker Group
Des Moines 515-262-9308

KENTUCKY

Certified Service Center
Lexington 859-254-8854

Certified Service Center
Louisville 502-964-7007

LOUISIANA

Chandlers Parts & Service
Baton Rouge 225-272-6620

MARYLAND

Electric Motor Service
Baltimore 410-467-8080

GCS Service
Silver Spring 301-585-7550

MASSACHUSETTS

Ace Service Co., Inc.
Needham 781-449-4220

MICHIGAN

Commercial Kitchen Service
Bay City 517-893-4561

Bildons Appliance Service
Detroit 248-478-3320

Midwest Food Equip. Service
Grandville 616-261-2000

MINNESOTA

GCS Service
Minneapolis 612-546-4221

MISSOURI

General Parts
Kansas City 816-421-5400

Commercial Kitchen Services
St. Louis 314-890-0700

Kaemmerlen Parts & Service
St. Louis 314-535-2222

NEBRASKA

Anderson Electric
Omaha 402-341-1414

NEVADA

Burney’s Commercial
Las Vegas 702-736-0006

Hi. Tech Commercial Service
N. Las Vegas 702-649-4616

NEW JERSEY

Jay Hill Repair
Fairfield 973-575-9145

Service Plus
Flanders 973-691-6300

NEW YORK

Acme American Repairs, Inc.
Brooklyn 718-456-6544

Alpro Service Co.
Brooklyn 718-386-2515

Appliance Installation
Buffalo 716-884-7425

Northern Parts Dist.
Plattsburgh 518-563-3200

J.B. Brady, Inc.
Syracuse 315-422-9271

NORTH CAROLINA

Authorized Appliance
Charlotte 704-377-4501

OHIO

Akron/Canton Comm. Svc. Inc.
Akron 330-753-6635

Certified Service Center
Cincinnati 513-772-6600

Commercial Parts and Service
Columbus 614-221-0057

Electrical Appl. Repair Service
Independence 216-459-8700

E. A. Wichman Co.
Toledo 419-385-9121

OKLAHOMA

Hagar Rest. Service, Inc.
Oklahoma City 405-235-2184

Krueger, Inc.
Oklahoma City 405-528-8883

OREGON

Ron’s Service, Inc.
Portland 503-624-0890

PENNSYLVANIA

Elmer Schultz Services
Philadelphia 215-627-5401

FAST Comm. Appl. Service
Philadelphia 215-288-4800

Appliance Installation & Service
Pittsburgh 412-809-0244

K & D Service Co.
Harrisburg 717-236-9039

Electric Repair Co.
Reading 610-376-5444

RHODE ISLAND

Marshall Electric Co.
Providence 401-331-1163

SOUTH CAROLINA

Whaley Foodservice Repair
W. Columbia 803-791-4420

TENNESSEE

Camp Electric
Memphis 901-527-7543

TEXAS

GCS Service

Fort Worth 817-831-0381

Armstrong Repair Service

Houston 713-666-7100

Commercial Kitchen Repair Co.

San Antonio 210-735-2811

UTAH

La Monica’s Rest. Equip. Service

Murray 801-263-3221

VIRGINIA

Daubers

Norfolk 757-855-4097

Daubers

Springfield 703-866-3600

WASHINGTON

Restaurant Appl. Service

Seattle 206-524-8200

WISCONSIN

A.S.C., Inc.

Madison 608-246-3160

A.S.C., Inc.

Milwaukee 414-543-6460

CANADA

ALBERTA

Key Food Equipment Service

Edmonton 780-438-1690

BRITISH COLUMBIA

Key Food Equipment Service

Vancouver 604-433-4484

MANITOBA

Air Rite, Inc.

Winnepeg 204-895-2300

NEW BRUNSWICK

EMR Services, Ltd.

Moncton 506-855-4228

ONTARIO

R.G. Henderson Ltd.

Toronto 416-422-5580

Choquette CKS

Ottawa 613-739-8458

QUEBEC

Choquette CKS

Montreal 514-722-2000

Choquette CKS
Québec City 418-681-3944