Hatco GRSSR20-DLH Installation Manual

GLO-RAY

®

Round Heated Stone Shelf

with Display Lamp

GRSSR20-DL & GRSSR20-DLH

Series

Installation & Operating Manual

I&W #07.05.179.00

This manual contains important safety information
concerning the maintenance, use and operation of this
product. Failure to follow the instructions contained in
this manual may result in serious injury. If you’re unable
to understand the contents of this manual, please bring
it to the attention of your supervisor. Do not operate this
equipment unless you have read and understood the
contents of this manual.

Este manual contiene importante información sobre
seguridad concerniente al mantenimiento, uso y
operación de este producto. Cualquier falla en el
seguimiento de las instrucciones contenidas en este
manual puede resultar en un serio daño. Si usted no
puede entender el contenido de este manual por favor
pregunte a su supervisor. No opere este equipo al
menos que haya leído y comprendido el contenido de
este manual.

Form No. GRSSRDLM-0607

i

CONTENTS

Important Owner Information...............................i

Introduction ...........................................................i

Important Safety Information..............................1

Model Description................................................3

All Models........................................................3

GRSSR20-DL (Standard Wattage)..................3

GRSSR20-DLH (High Wattage)......................3

Model Designation ...............................................3

Specifications.......................................................4

Electrical Rating Chart ....................................4

Plug Configuration...........................................4

Dimensions......................................................4

Installation ............................................................5

Unpacking .......................................................5

Location...........................................................5

Operation ..............................................................6

Maintenance .........................................................7

General............................................................7

Cleaning ..........................................................7

Cleaning for Swanstone Solid Surface ...........7

Cleaning for Decorative Lamp ........................7

Heat Bulb Replacement ..................................8

Accessories..........................................................9

Cutting Board/Carving Station.........................9

Troubleshooting.................................................10

Hatco Limited Warranty.....................................11

Authorized Parts Distributors ............Back Cover

Record the model number, serial number (located on
the side of the unit), voltage and purchase date of
your Round Heated Stone Shelf with Display Lamp
in the spaces below. Please have this information
available when calling Hatco for service assistance.

Model No. ________________________________

Serial No. ________________________________

Voltage __________________________________

Date of Purchase __________________________

Business 8:00 a.m. to 5:00 p.m.
Hours: Central Standard Time

(Summer Hours: June to September –
8:00 a.m. to 5:00 p.m. C.D.T.
Monday through Thursday
8:00 a.m. to 2:30 p.m. C.D.T. Friday)

Telephone: [phone]

Fax: [phone] (Parts & Service)

[phone] (International)

24-Hour 7-Day Parts & Service
Assistance available in the United
States and Canada by calling
[phone].

Additional information can be found by visiting our
web site at www.hatcocorp.com

Hatco Glo-Ray®Round Heated Stone Shelf with
Display Lamp is designed to keep hot food at optimum
serving temperatures and to enhance restaurant
decor. Heat is focused directly above and below,
providing effective insulation for prolonged serving
times.

Hatco foodwarmers are quality built to meet the
demands of foodservice operations and provide
years of trouble-free performance.

This manual provides the installation, safety and
operating instructions for the Glo-Ray Round Heated
Stone Shelf with Display Lamp. We recommend all
installation, operating and safety instructions
appearing in this manual be read prior to installation
or operation of your foodwarmer. Safety instructions

that appear in this manual after a warning symbol

and the words WARNING or CAUTION printed in

bold face are very important. WARNING means
there is the possibility of serious personal injury or
death to yourself or others. CAUTION means
there is the possibility of minor or moderate injury.
NOTICE without the symbol signifies the possibility
of equipment or property damage only.

Hatco Glo-Ray Round Heated Stone Shelf with
Display Lamp is a product of extensive research and
field testing. The materials used were selected for
maximum durability, attractive appearance and
optimum performance. Every unit is thoroughly
inspected and tested prior to shipment.

IMPORTANT OWNER INFORMATION

INTRODUCTION

Form No. GRSSRDLM-0607

1

IMPORTANT SAFETY INFORMATION

WARNINGS

For safe and proper operation, plug unit into
a properly grounded electrical outlet of the
correct voltage, wire size and plug
configuration. If the plug and receptacle do
not match, contact a qualified electrician to
determine the proper voltage and size and to
install the proper electrical outlet.

The Glo-Ray®Round Heated Stone Shelf
with Display Lamp is not waterproof. To
avoid electrical shock or personal injury DO
NOT submerge in water. Do not operate if it
has been submerged in water. Do not steam
clean.

To avoid any injury, turn the power switch
OFF, unplug the unit from the power source
and allow to cool completely before
performing any maintenance or cleaning.

To avoid any injury, turn the power supply
OFF to the mounting location before
installing.

For safe and proper operation, the unit must
be located at 1" (25.4 mm) distance from
combustible walls and materials. If safe
distances are not maintained, discoloration
or combustion could occur.

To prevent any injury or damage to the unit
do not pull unit by power cord.

To prevent any injury, discontinue use if
power cord is frayed or worn.

Some exterior surfaces on the unit will get
hot. Use caution when touching these areas
to avoid injury.

WARNINGS

GRSSR20-DL standard watt heat lamps
(250 watt bulb) must have a minimum of
16" (406 mm) above a flammable surface.
If safe distances are not maintained,
discoloration or combustion could occur.

GRSSR20-DLH high watt heat lamps
(375 watt bulb) must have a minimum of
27" (686 mm) above a flammable surface. If
safe distances are not maintained,
discoloration or combustion could occur.

For safe and proper operation, do not install
a 375 watt bulb into a GRSSR20-DL standard
watt unit.

If service is required on this unit, contact
your Authorized Hatco Service Agent, or
contact the Hatco Service Department at
800-558-0607 or 414-671-6350; fax 800-690­2966 or International fax [phone].

This product has no “user” serviceable
parts. To avoid damage to the unit or injury
to personnel, use only Authorized Hatco
Service Agents and Genuine Hatco
Replacement Parts when service is required.

Genuine Hatco Replacement Parts are
specified to operate safely in the
environments in which they are used. Some
aftermarket or generic replacement parts do
not have the characteristics that will allow
them to operate safely in Hatco equipment.
It is essential to use Hatco Replacement
Parts when repairing Hatco equipment.
Failure to use Hatco Replacement Parts may
subject operators of the equipment to
hazardous electrical voltage, resulting in
electrical shock or burn.

IMPORTANT! Read the following important safety information to avoid personal injury or
death, and to avoid damage to the equipment or property.

Form No. GRSSRDLM-0607

2

IMPORTANT SAFETY INFORMATION

CAUTIONS

Damage to the countertop material caused
by heat generated from Hatco equipment is
not covered under the Hatco Warranty.
Contact the manufacturer of the base
material for application information.

To avoid any injury or damage locate the
unit at the proper counter height, in an area
that is convenient for use. The location
should be level to prevent the unit or its
contents from accidentally falling, and
strong enough to support the weight of the
unit and food.

CAUTIONS

Unit is not weatherproof. For safe and
proper operation locate the unit indoors
where the ambient air temperature is
constant and is a minimum of 70°F (21°C).

Some exterior surfaces on the unit will get
hot. Use caution when touching these areas
to avoid injury.

NOTICES
Use only non-abrasive cleaners. Abrasive
cleaners could scratch the finish of your
unit, marring its appearance and making it
susceptible to dirt accumulation.

IMPORTANT! Read the following important safety information to avoid personal injury or
death, and to avoid damage to the equipment or property.

Form No. GRSSRDLM-0607

3

MODEL DESCRIPTION

ALL MODELS

Hatco’s Glo-Ray®Round Heated Shelf with Display
Lamp features a thermostatically controlled
Swanstone®base available in stone colors of Gray
Granite, Bermuda Sand, Night Sky and Sawgrass;
and display lamp offering Designer colors in Warm
Red, Black, Gray Granite, White Granite, Navy Blue
and Hunter Green.

Each foodwarmer comes equipped with an On/Off
(lighted) rocker switch, adjustable thermostat and 6'
(1829 mm) power cord with attached plug.

GRSSR20-DL (Standard Wattage)

Standard wattage models (DL) feature a 250 watt
upper infrared heat bulb.

GRSSR20-DLH (High Wattage)

High wattage models (DLH) feature a 375 watt upper
infrared heat bulb.

Figure 1. Model GRSSR20-DL

Figure 2. Model Designation

GR SS R 20 - DL H 775 16

MODEL DESIGNATION

Glo-Ray

Stone Shelf

Round

Shade Style

Distance between Upper

Lamp and Heated Base

Shelf Diameter – Inches

High Watt

Decorative Lamp

Form No. GRSSRDLM-0607

4

SPECIFICATIONS

PLUG CONFIGURATION

Units are supplied from the factory with a 6' (1.8 m)
electrical cord and plug installed. (See Figure 3.)

WARNING
For safe and proper operation, plug unit into a
properly grounded electrical outlet of the correct
voltage, wire size and plug configuration. If the
plug and receptacle do not match, contact a
qualified electrician to determine the proper
voltage and size and install the proper electrical
outlet.

ELECTRICAL RATING CHART

Figure 3. Plug Configuration

*

Receptacle not supplied by Hatco.

Figure 4. Dimensions

NEMA 5-15P

Dia. 20"

(508 mm)

2-5/8"

(65 mm)

DIMENSIONS

*

34-1/2" (876 mm) Standard Watt

45-1/2" (1156 mm) High Watt

Model Voltage Wattage Amperage Plug Configuration Shipping Weight

GRSSR20-DL 120 650 5.4 NEMA 5-15P

40 lbs.
(18 kg)

GRSSR20-DLH 120 775 6.5 NEMA 5-15P

40 lbs.
(18 kg)

16" (406 mm) Standard Watt

27" (686 mm) High Watt

Form No. GRSSRDLM-0607

5

INSTALLATION

UNPACKING

The Glo-Ray® Round Heated Stone Shelf with
Display Lamp is shipped pre-assembled and ready
for operation. Care should be taken when unpacking
shipping carton to avoid damage to unit and
components enclosed.

WARNING
To prevent any injury or damage to the unit do
not pull unit by power cord.

WARNING
To prevent any injury, discontinue use if power
cord is frayed or worn.

1. Remove unit from box.

2. Remove information packet. To prevent delay in

obtaining warranty coverage, fill out and mail
in the warranty card.

3. Remove protective paper from all surfaces before
placing into service.

LOCATION

NOTE: Unit must be transported in the upright
position.

For proper operation and maximum performance,
locate the Glo-Ray Round Heated Stone Shelf with
Display Lamp in an area where the ambient air
temperature is constant and is a minimum of 70°F
(21°C). Areas which are susceptible to active air
movements or currents should be avoided, i.e., near
exhaust fans or hoods and air conditioning ducts.

CAUTION
Unit is not weatherproof. For safe and proper
operation the unit must be located indoors
where the ambient air temperature is a minimum
of 70°F (21°C) and a maximum of 85°F (29°C).

WARNING
For safe and proper operation, the unit must
be located at 1" (25.4 mm) distance from
combustible walls and materials. If safe
distances are not maintained, discoloration or
combustion could occur.

CAUTION
To avoid any injury or damage locate the unit at
the proper counter height, in an area that is
convenient for use. The location should be level
to prevent the unit or its contents from
accidentally falling, and strong enough to
support the weight of the unit and food.

WARNING
To avoid any injury or damage to the unit(s)
connect to a properly grounded electrical
supply. Contact a qualified electrician to
determine the proper voltage, wire size and
installation method.

WARNING
The Glo-Ray Round Heated Stone Shelf with
Display Lamp must have a minimum of 1" (25 mm)
clearance along the sides of combustible walls
and materials. If safe distances are not
maintained, discoloration or combustion could
occur.

Figure 5. Minimum Clearance from Combustibles

1" (25.4 mm)1" (25.4 mm)

Form No. GRSSRDLM-0607

6

OPERATION

WARNING
Plug unit into a properly grounded electrical
outlet of the correct voltage, size and plug
configuration. If the plug and receptacle do not
match, contact a qualified electrician to
determine the proper voltage and size and install
the proper electrical outlet.

CAUTION
Some exterior surfaces on the unit will get hot.
Use caution when touching these areas to avoid
injury.

CAUTION
Unit is not weatherproof. For safe and proper
operation locate the unit indoors

where the
ambient air temperature is a minimum of 70°F
(21°C).

WARNING

The Glo-Ray

®

Round Heated Stone Shelf with
Display Lamp is not waterproof. To avoid
electrical shock or personal injury DO NOT
submerge in water. Do not operate if it has been
submerged in water.

1. Plug unit into a properly grounded electrical outlet
of the correct voltage, size and plug
configuration. See SPECIFICATIONS for details.

2. Place the Power ON/OFF Switch in the ON
position. See Figure 6. The heat bulb will light
when the unit is energized.

3. Turn the thermostat to the desired heated stone
base temperature setting. Base temperature
range is 100° – 200°F (38° – 93°C).

4. Allow unit 30 minutes to reach operating
temperature.

Figure 6. Controls

Power ON/OFF

Switch

Shelf

Thermostat

Power

Cord

Form No. GRSSRDLM-0607

7

MAINTENANCE

GENERAL

The Hatco Glo-Ray®Round Heated Stone Shelf with
Display Lamp is designed for maximum durability
and performance, with minimum maintenance.

WARNING
To avoid any injury or damage to the unit turn the
power switch OFF, unplug the unit and allow to
cool before performing any maintenance or
cleaning.

CLEANING

General

To preserve the finish of the Glo-Ray Round Heated
Stone Shelf with Display Lamp, it is recommended
that the surfaces be wiped daily with a damp cloth.

WARNING
The Glo-Ray Round Heated Stone Shelf with
Display Lamp is not waterproof. To avoid
electrical shock or personal injury or damage to
the unit DO NOT submerge or saturate with
water. Do not operate if it has been submerged
or saturated with water.

CLEANING FOR SWANSTONE SOLID
BASE SURFACE

Use of the following products will not damage the
Swanstone®Solid Surface. Follow the directions on
the product labels. If these methods fail to produce
acceptable results, contact the Swanstone
representative in your area.

Hard to Remove Stains

For hard to remove stains, abrasive cleaners
recommended include Ajax, Comet, Bon Ami, or Bar
Keeper’s Friend. Also, the use of an abrasive pad
such as “Scotch-Brite.”

NOTE: Do not use steel wool or met

al scouring

pads.

Mineral Based Stains

For a mineral based stain, cleaners designed to
remove iron or rust are recommended and should
not harm Swanstone.

Scratches

For scratches use sandpaper starting with coarsest
grit and going to finest grit until scratch disappears.
Blend area in with abrasive finishing pad.

WARNING
If service is required on this unit, contact your
Authorized Hatco Service Agent, or contact the
Hatco Service Department at 800-558-0607 or
414-671-6350; fax [phone] or International
fax [phone].

WARNING
This product has no “user” serviceable parts. To
avoid damage to the unit or injury to personnel,
use only Authorized Hatco Service Agents and
Genuine Hatco Replacement Parts when service
is required.

WARNING
Genuine Hatco Replacement Parts are specified
to operate safely in the environments in which
they are used. Some aftermarket or generic
replacement parts do not have the
characteristics that will allow them to operate
safely in Hatco equipment. It is essential to use
Hatco Replacement Parts when repairing Hatco
equipment. Failure to use Hatco Replacement
Parts may subject operators of the equipment to
hazardous electrical voltage, resulting in
electrical shock or burn.

CLEANING FOR DECORATIVE LAMP

To preserve the finish of the upper Decorative Heat
Lamp it is recommended that the lamp shade
surface be wiped daily with a soft damp cloth.
Stubborn stains can be removed with a mild non­abrasive cleaner.

WARNING
To avoid electrical shock or personal injury, do
not steam clean or use excessive water on the
unit.

WARNING
To avoid any injury or electrical shock, turn
the power switch and the fuse disconnect
switch/circuit breaker off. Allow to cool
completely before performing any maintenance
or cleaning.

NOTICE
Use only non-abrasive cleaners. Abrasive
cleaners could scratch the finish of your
Decorative Heat Lamp, marring its appearance
and making it susceptible to dirt accumulation.

Form No. GRSSRDLM-0607

8

MAINTENANCE

HEAT BULB REPLACEMENT

Each standard wattage Decorative Heat Lamp (DL)
is supplied with one clear, uncoated infrared heat
bulb rated at 250 watts. Each high wattage
Decorative Heat Lamp (DLH) is supplied with one
clear, uncoated infrared heat bulb rated at 375 watts.
250 watt bulbs may also be used in DLH units.

WARNING
For safe and proper operation, do not install a
375 watt bulb into a DL standard watt lamp.

1. To replace a bulb, place the switch in the OFF
position and allow the bulb to cool completely.

2. Bulbs have a threaded base. Unscrew the heat
bulb counterclockwise from the unit and replace
with a new bulb.

The following replacement bulbs are available from
the factory or Hatco Authorized Parts Distributor.

DL (standard wattage)

250 Watt 120V Red Coated 02.30.068.00
250 Watt 120V Clear Coated 02.30.069.00
250 Watt 120V Red Uncoated 02.30.070.00
250 Watt 120V Clear Uncoated 02.30.071.00

DLH (high wattage)

375 Watt 120V Clear Uncoated 02.30.093.00
375 Watt 120V Red Uncoated 02.30.094.00
375 Watt 120V Clear Coated 02.30.097.00
375 Watt 120V Red Coated 02.30.098.00

Form No. GRSSRDLM-0607

9

ACCESSORIES

CUTTING BOARD/CARVING STATION

Made of NSF Approved food safe materials.

Installation

Cutting board comes with rubber feet on bottom to fit
right on top of base.

Material

Made of same material as Swanstone

®

base.

Colors

Available in the same colors as the base, Gray
Granite, Bermuda Sand, Night Sky and Sawgrass.

Size

21" (533 mm) wide by 15-3/4" (400 mm) deep

CLEANING FOR SWANSTONE CUTTING BOARD
SURFACE

Use of the following products will not damage the
Swanstone Solid Surface. Follow the directions on
the product labels. If these methods fail to produce
acceptable results, contact the Swanstone
representative in your area.

Hard to Remove Stains

For hard to remove stains, abrasive cleaners
recommended include Ajax, Comet, Bon Ami, or Bar
Keeper’s Friend. Also, the use of an abrasive pad
such as “Scotch-Brite.”

NOTE: Do not use steel wool or met

al scouring

pads.

Mineral Based Stains

For a mineral based stain, cleaners designed to
remove iron or rust are recommended and should
not harm Swanstone.

Scratches

For scratches use sandpaper starting with coarsest
grit and going to finest grit until scratch disappears.
Blend area in with abrasive finishing pad.

Figure 7. Cutting Board

Cutting Board

Form No. GRSSRDLM-0607

10

SYMPTOM PROBABLE CAUSE CORRECTIVE ACTION

Unit too hot. Base thermostat control set too high. Adjust thermostat control to a lower

setting.

Base thermostat control stuck in the
ON position.

Contact Authorized Service Agency
for repair.

Unit plugged into an incorrect power
supply.

Verify with qualified personnel that
power supply matches unit
specification.

Unit not hot enough. Base thermostat control set too low. Adjust thermostat control to a higher

setting.

Location of unit is susceptible to air
currents (air conditioning ducts or
exhaust fans).

Block air currents or relocate unit.

Upper infrared heat bulb does not light. Bulb is defective. Replace heat bulb.

Unit not working at all. Unit not plugged in. Plug unit into proper power supply.

Unit not turned on. Place ON/OFF switch in the ON

position.

ON/OFF switch is not functioning. Contact Authorized Service Agent for

repair.

Base heating element is burned out. Contact Authorized Service Agent for

repair.

Base thermostat control is defective. Contact Authorized Service Agent for

repair.

WARNING
To avoid any injury or damage, the Heated Stone
Shelf must only be serviced by qualified
personnel.

WARNING
To avoid any injury or damage to the unit turn the
power switch OFF, unplug the unit and allow to
cool before performing any maintenance or
cleaning.

TROUBLESHOOTING

Form No. GRSSRDLM-0607

11

HATCO LIMITED WARRANTY

1. PRODUCT WARRANTY

Hatco warrants the products that it manufactures
(the “Products”) to be free from defects in materials
and workmanship, under normal use and service, for
a period of one (1) year from the date of purchase
when installed and maintained in accordance with
Hatco’s written instructions or 18 months from the
date of shipment from Hatco. Buyer must establish
the product’s purchase date by returning Hatco’s
Warranty Registration Card or by other means
satisfactory to Hatco in its sole discretion.

Hatco warrants the following Product components to
be free from defects in materials and workmanship
from the date of purchase (subject to the foregoing
conditions) for the period(s) of time and on the
conditions listed below:

a) One (1) Year Parts and Labor PLUS One (1)

Additional Year Parts-Only Warranty:

Toaster Elements (metal sheathed)
Drawer Warmer Elements (metal sheathed)
Drawer Warmer Drawer Rollers and Slides
Food Warmer Elements (metal sheathed)
Display Warmer Elements (metal sheathed
air heating)
Holding Cabinet Elements (metal sheathed
air heating)
Built-In Heated Well Elements (metal sheathed)

b) One (1) Year Parts and Labor PLUS Four

(4) Years Parts-Only Warranty on pro-rated
terms that Hatco will explain at Buyer’s
request:

3CS and FR Tanks

c) One (1) Year Parts and Labor PLUS Nine

(9) Years Parts-Only Warranty on:

Electric Booster Heater Tanks
Gas Booster Heater Tanks

THE FOREGOING WARRANTIES ARE EXCLUSIVE
AND IN LIEU OF ANY OTHER WARRANTY,
EXPRESSED OR IMPLIED, INCLUDING BUT NOT
LIMITED TO ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE OR PATENT OR
OTHER INTELLECTUAL PROPERTY RIGHT
INFRINGEMENT. Without limiting the generality of
the foregoing, SUCH WARRANTIES DO NOT
COVER: Coated incandescent light bulbs,
fluorescent lights, lamp warmer heat bulbs, glass
components, Product failure in booster tank, fin tube
heat exchanger, or other water heating equipment,
caused by liming, sediment buildup, chemical attack
or freezing, Product misuse, tampering or
misapplication, improper installation or application of
improper voltage.

2. LIMITATION OF REMEDIES AND
DAMAGES

Hatco’s liability and Buyer’s exclusive remedy
hereunder will be limited solely, at Hatco’s option, to
repair or replacement by a Hatco-authorized service
agency (other than where Buyer is located outside of
the United States, Canada, United Kingdom or
Australia in which case Hatco’s liability and Buyer’s
exclusive remedy hereunder will be limited solely to
replacement of part under warranty) with respect to
any claim made within the applicable warranty
period referred to above. Hatco reserves the right to
accept or reject any such claim in whole or in part.
Hatco will not accept the return of any Product
without prior written approval from Hatco, and all
such approved returns shall be made at Buyer’s sole
expense. HATCO WILL NOT BE LIABLE, UNDER
ANY CIRCUMSTANCES, FOR CONSEQUENTIAL
OR INCIDENTAL DAMAGES, INCLUDING BUT
NOT LIMITED TO LABOR COSTS OR LOST
PROFITS RESULTING FROM THE USE OF OR
INABILITY TO USE THE PRODUCTS OR FROM
THE PRODUCTS BEING INCORPORATED IN OR
BECOMING A COMPONENT OF ANY OTHER
PRODUCT OR GOODS.

Form No. GRSSRDLM-0607

12

NOTES:

HATCO CORPORATION

P.O. Box 340500, Milwaukee, WI 53234-0500 U.S.A.

[phone] [phone]

Parts & Service Fax [phone] Int’l. Fax [phone]

www.hatcocorp.com

HATCO AUTHORIZED PARTS DISTRIBUTORS

ALABAMA

Jones McLeod Appl. Svc.
Birmingham 205-251-0159

ARIZONA

Auth. Comm. Food Equip.
Phoenix 602-234-2443

Byassee Equipment Co.
Phoenix 602-252-0402

CALIFORNIA

Industrial Electric
Commercial Parts & Service, Inc.
Huntington Beach 714-379-7100

Chapman Appl. Service
San Diego 619-298-7106

P & D Appliance
Commercial Parts & Service, Inc.
S. San Francisco 650-635-1900

COLORADO

Hawkins Commercial Appliance
Englewood 303-781-5548

FLORIDA

Whaley Foodservice Repair
Jacksonville 904-725-7800

Nass Service Co., Inc.
Orlando 407-425-2681

B.G.S.I.
Pompano Beach 954-971-0456

Comm. Appliance Service
Tampa 813-663-0313

GEORGIA

TWC Services
Smyrna 770-438-9797

Heritage Service Group
Norcross 866-388-9837

Southeastern Rest. Svc.
Norcross 770-446-6177

HA

WAII

Burney’s Comm. Service, Inc.
Honolulu 808-848-1466

Food Equip Parts & Service
Honolulu 808-847-4871

ILLINOIS

Parts Town
Lombard 708-865-7278

Eichenauer Elec. Service
Decatur 217-429-4229

Midwest Elec. Appl. Service
Elmhurst 630-279-8000

Cone’s Repair Service
Moline 309-797-5323

INDIANA

GCS Service
Indianapolis 317-545-9655

IOW

A

Electric Motor Service Co.
Davenport 319-323-1823

Goodwin Tucker Group
Des Moines 515-262-9308

KENTUCKY

Certified Service Center
Lexington 859-254-8854

Certified Service Center
Louisville 502-964-7007

LOUISIANA

Chandlers Parts & Service
Baton Rouge 225-272-6620

MAR

YLAND

Electric Motor Service
Baltimore 410-467-8080

GCS Service
Silver Spring 301-585-7550

MASSACHUSETTS

Ace Service Co., Inc.
Needham 781-449-4220

MICHIGAN

Commercial Kitchen Service
Bay City 517-893-4561

Bildons Appliance Service
Detroit 248-478-3320

Midwest Food Equip. Service
Grandville 616-261-2000

MINNESOT

A

GCS Service
Minneapolis 612-546-4221

MISSOURI

General Parts
Kansas City 816-421-5400

Commercial Kitchen Services
St. Louis 314-890-0700

Kaemmerlen Parts & Service
St. Louis 314-535-2222

NEBRASKA

Anderson Electric
Omaha 402-341-1414

NEV

ADA

Burney’s Commercial
Las Vegas 702-736-0006

Hi. Tech Commercial Service
N. Las Vegas 702-649-4616

NEW JERSEY

Jay Hill Repair
Fairfield 973-575-9145

Service Plus
Flanders 973-691-6300

NEW

YORK

Acme American Repairs, Inc.
Brooklyn 718-456-6544

Alpro Service Co.
Brooklyn 718-386-2515

Appliance Installation
Buffalo 716-884-7425

Northern Parts Dist.
Plattsburgh 518-563-3200

J.B. Brady, Inc.
Syracuse 315-422-9271

NORTH CAROLINA

Authorized Appliance
Charlotte 704-377-4501

OHIO

Akron/Canton Comm. Svc. Inc.
Akron 330-753-6635

Certified Service Center
Cincinnati 513-772-6600

Commercial Parts and Service
Columbus 614-221-0057

Electrical Appl. Repair Service
Independence 216-459-8700

E. A. Wichman Co.
Toledo 419-385-9121

OKLAHOMA

Hagar Rest. Service, Inc.
Oklahoma City 405-235-2184

Krueger, Inc.
Oklahoma City 405-528-8883

OREGON

Ron’s Service, Inc.
Portland 503-624-0890

PENNSYL

VANIA

Elmer Schultz Services
Philadelphia 215-627-5401

FAST Comm. Appl. Service
Philadelphia 215-288-4800

Appliance Installation & Service
Pittsburgh 412-809-0244

K & D Service Co.
Harrisburg 717-236-9039

Electric Repair Co.
Reading 610-376-5444

RHODE ISLAND

Marshall Electric Co.
Providence 401-331-1163

SOUTH CAROLINA

Whaley Foodservice Repair
W. Columbia 803-791-4420

TENNESSEE

Camp Electric
Memphis 901-527-7543

TEXAS

GCS Service
Fort Worth 817-831-0381

Armstrong Repair Service
Houston 713-666-7100

Commercial Kitchen Repair Co.
San Antonio 210-735-2811

UT

AH

La Monica’s Rest. Equip. Service
Murray 801-263-3221

VIRGINIA

Daubers
Norfolk 757-855-4097

Daubers
Springfield 703-866-3600

WASHINGTON

Restaurant Appl. Service
Seattle 206-524-8200

WISCONSIN

A.S.C., Inc.
Madison 608-246-3160

A.S.C., Inc.
Milwaukee 414-543-6460

CANADA

ALBERT

A

Key Food Equipment Service
Edmonton 780-438-1690

BRITISH COLUMBIA

Key Food Equipment Service
Vancouver 604-433-4484

MANIT

OBA

Air Rite, Inc.
Winnepeg 204-895-2300

NEW BRUNSWICK

EMR Services, Ltd.
Moncton 506-855-4228

ONT

ARIO

R.G. Henderson Ltd.
Toronto 416-422-5580

Choquette CKS
Ottawa 613-739-8458

QUÉBEC

Choquette CKS
Montreal 514-722-2000

Choquette CKS
Québec City 418-681-3944

Printed in U.S.A. June 2007 Part No. 07.04.409.00 Form No. GRSSRDLM-0607