Hatco GRPWSM-1001 User Manual

GLO-RAY

®

Pizza Warmer

GRPWS Series

Installation &

Operating Manual

I&W #07.05.102.00

This manual contains important safety information
concerning the maintenance, use and operation of
this product. Failure to follow the instructions
contained in this manual may result in serious injury.
If you are unable to understand the contents of this
manual, please bring it to the attention of your
supervisor. Do not operate this equipment unless you
have read and understood the contents of this
manual.

Este manual contiene importante información sobre
seguridad concerniente al mantenimiento, uso
y operación de este producto. Cualquier falla en el
seguimiento de las instrucciones contenidas en este
manual puede resultar en un serio daño. Si usted no
puede entender el contenido de este manual por
favor pregunte a su supervisor. No opere este equipo
al menos que haya leído y comprendido el contenido
de este manual.

i

INTRODUCTION

The Hatco Glo-Ray®GRPWS Pizza Warmers are
perfect for holding boxed or bagged pizza on a buffet
line or at temporary serving areas. These warmers
hold hot wrapped pizzas and keep them at optimum
serving temperatures without affecting quality. A
thermostatically controlled heated base extends the
holding times of most wrapped food. These units also
feature incandescent lights along with a cord and
plug set(s).

This manual provides the installation, safety and
operating instructions for the Glo-Ray Pizza Warmers.
We recommend all installation, operating and safety
instructions appearing in this manual be read prior to
installation or operation of your Hatco Pizza Warmer.

Safety instructions that appear in this manual after a
warning symbol and the words WARNING or

CAUTION printed in bold face are very important.

WARNING means there is the possibility of serious

injury or death to yourself or others. CAUTION
means there is the possibility of minor or moderate
injury. CAUTION without the symbol signifies the
possibility of equipment or property damage only.

Hatco Glo-Ray Pizza Warmers are a product of extensive
research and field testing. The materials used were
selected for maximum durability, attractive appearance
and optimum performance. Every unit is thoroughly
inspected and tested prior to shipment.

CONTENTS

Important Owner Information.....................................i

Introduction ...................................................................i

Important Safety Instructions .....................................1

Model Descriptions .......................................................2

All Models ..............................................................2

Specifications.................................................................2

Plug Configurations ................................................2

Electrical Rating Chart - Dual Shelf.......................3

Electrical Rating Chart - Triple Shelf.....................3

Electrical Rating Chart - Quadruple Shelf..............3

Dimensions..............................................................4

Installation.....................................................................5

All Models ..............................................................5

Location ..................................................................6

Operation.......................................................................6

Maintenance ..................................................................7

General ....................................................................7

Cleaning ..................................................................7

Display Light Bulb Replacement............................7

Accessories.....................................................................8

Temperature Indicating Display (TID) ...................8

Hatco Limited Warranty .............................................9

Authorized Parts Distributors....................Back Cover

IMPORTANT OWNER INFORMATION

Record the model number, serial number (identification
plate located on the top rear of of the unit), voltage and
purchase date of your Glo-Ray Pizza Warmer in the
spaces below. Please have this information available
when calling Hatco for service assistance.

Model No. ____________________________________

Serial No. ____________________________________

Voltage ______________________________________

Date of Purchase ______________________________

Business 8:00 a.m. to 5:00 p.m.
Hours: Central Standard Time

(Summer Hours: June to September –
8:00 a.m. to 5:00 p.m. C.D.T.
Monday through Thursday
8:00 a.m. to 2:30 p.m. C.D.T. Friday)

Telephone: [phone]

Fax: [phone] (Parts & Service)

[phone] (International)

Additional information can be found by visiting our

web site at www.hatcocorp.com.

Form No. GRPWSM-1001

IMPORTANT SAFETY INSTRUCTIONS

1

Form No. GRPWSM-1001

IMPORTANT! Read the following important safety instructions to avoid personal injury or death,
and to avoid damage to the equipment or property.

WARNINGS

Plug unit into an electrical outlet of the correct
voltage, size and plug configuration. If the plug
and receptacle do not match, contact a qualified
electrician to determine the proper voltage and
size and install the proper electrical outlet.

To avoid any injury, turn the power switch off,
unplug the unit from the power source and allow
to cool before performing any maintenance.

For safe and proper operation, the unit must be
located a reasonable distance from combustible
walls and materials. If safe distances are not
maintained, discoloration or combustion
could occur.

Unit is not waterproof. DO NOT submerge in
water. Do not operate if it has been submerged
in water.

To avoid electrical shock or personal injury, do
not steam clean or use excessive water on the unit.

Only light bulbs which meet or exceed N.S.F.
standards, specifically designed for food holding
areas must be used. Breakage of light bulbs not
specially coated could result in personal injury
and/or food contamination.

If service is required on this unit, contact your
Authorized Hatco Service Agent, or contact the
Hatco Service Department at 800-558-0607 or
414-671-6350; fax [phone] or International
fax [phone].

This product has no “user” serviceable parts. To
avoid damage to the unit or injury to personnel,
use only Authorized Hatco Service Agents and
Genuine Hatco Replacement Parts when service
is required.

Genuine Hatco Replacement Parts are specified to
operate safely in the environments in which they
are used. Some aftermarket or generic
replacement parts do not have the characteristics
that will allow them to operate safely in Hatco
equipment. It is essential to use Hatco
Replacement Parts when repairing Hatco
equipment. Failure to use Hatco Replacement
Parts may subject operators of the equipment to
hazardous electrical voltage, resulting in electrical
shock or burn.

CAUTIONS

Some exterior surfaces on the unit will get
hot. Use caution when touching these areas to
avoid injury.

Locate the unit at the proper counter height, in an
area that is convenient for use. The location
should be level to prevent the unit or its contents
from accidentally falling, and strong enough to
support the weight of the unit.

The National Sanitation Foundation (NSF)
requires that GRPWS Series units over 36"
(91 cm) in length or weighing more than 80 lbs.
(36 kg) to be either sealed or raised on the
installation surface. If this unit cannot be sealed at
the point of use, 4" (10 cm) legs are included to
allow for proper cleaning access below unit. See
Hatco Accessories for installation instructions.

CAUTIONS

Use only non-abrasive cleaners. Abrasive cleaners
could scratch the finish marring its appearance
and making it susceptible to dirt accumulation.

MODEL DESCRIPTIONS

SPECIFICATIONS

2

ALL MODELS

All models are constructed of aluminum and stainless
steel, and feature tempered glass side panels, a separate
on/off switch and thermostat for each heat zone,
incandescent display lights, stainless steel box stops,
legs and a cord and plug set.

These models can be ordered in various widths of 24",
36", and 48" (61, 91, 122 cm), and in depths of 18" or
24" (46 to 61 cm). The unit is available in dual, triple or
quadruple shelf models.

Figure 1. Glo-Ray Model GRPWS - 4818T

Form No. GRPWSM-1001

PLUG CONFIGURATIONS

Units are supplied from the factory with an electrical
cord and plug. See Figure 2.

WARNING
Plug unit into an electrical outlet of the correct
voltage, size and plug configuration. If the plug and
receptacle do not match, contact a qualified
electrician to determine the proper voltage and size
and install the proper electrical outlet.

Figure 2. Plug Configurations

NEMA 5-15P NEMA 5-20P

NEMA 14-20P AS 3112

BS 1363 CEE 7/7 Schuko

SPECIFICATIONS

3

Form No. GRPWSM-1001

Model Voltage Watts Amps Plug Configuration Shipping Weight

GRPWS-2418D 120 750 6.3 NEMA 5-15P 76 lbs. (35 kg)

GRPWS-3618D 120 1068 8.9 NEMA 5-15P 106 lbs. (48 kg)

GRPWS-4818D 120 1370 11.4 NEMA 5-15P 136 lbs. (62 kg)

GRPWS-2424D 120 950 7.9 NEMA 5-15P 96 lbs. (44 kg)

GRPWS-3624D 120 1342 11.2 NEMA 5-15P 136 lbs. (62 kg)

GRPWS-4824D 120 1716 14.3 NEMA 5-15P* 177 lbs. (81 kg)

ELECTRICAL RATING CHART – GRPWS MODELS - DUAL SHELF

* NEMA 5-20P for Canada

* NEMA 5-20P for Canada

* NEMA 5-20P for Canada

ELECTRICAL RATING CHART – GRPWS MODELS - TRIPLE SHELF

Model Voltage Watts Amps Plug Configuration Shipping Weight

GRPWS-2418Q 120 1500 12.5 NEMA 5-15P* 119 lbs. (54 kg)

GRPWS-3618Q 120 2136 17.8 NEMA 5-20P 167 lbs. (76 kg)

120/208-240 2136 8.9 NEMA 14-20P 167 lbs. (76 kg)

GRPWS-4818Q 120/208-240 2740 11.4 NEMA 14-20P 214 lbs. (97 kg)

GRPWS-2424Q 120 1900 15.8 NEMA 5-20P 151 lbs. (69 kg)

GRPWS-3624Q 120/208-240 2684 11.2 NEMA 14-20P 214 lbs. (97 kg)

GRPWS-4824Q 120/208-240 3432 14.3 NEMA 14-20P 277 lbs. (126 kg)

ELECTRICAL RATING CHART – GRPWS MODELS - QUADRUPLE SHELF

Model Voltage Watts Amps Plug Configuration Shipping Weight

GRPWS-2418T 120 1125 9.4 NEMA 5-15P 98 lbs. (45 kg)

GRPWS-3618T 120 1602 13.4 NEMA 5-15P* 136 lbs. (62 kg)

GRPWS-4818T 120 2055 17.1 NEMA 5-20P 175 lbs. (80 kg)

120/208-240 2055 11.4 NEMA 14-20P 175 lbs. (80 kg)

GRPWS-2424T 120 1425 11.9 NEMA 5-15P 123 lbs. (56 kg)

220-230 (CE) 1276-1395 5.8-6.1 CEE 7/7 Schuko 123 lbs. (56 kg)

230-240 (CE) 1395-1518 6.1-6.3 BS-1363 123 lbs. (56 kg)

GRPWS-3624T 120 2013 16.8 NEMA 5-20P 175 lbs. (80 kg)

120/208-240 2013 11.2 NEMA 14-20P 175 lbs. (80 kg)

200 1776 8.9 AS 3112 175 lbs. (80 kg)

220-230 (CE) 1800-1967 8.2-8.6 CEE 7/7 Schuko 175 lbs. (80 kg)

230-240 (CE) 1967-2143 8.6-8.9 BS-1363 175 lbs. (80 kg)

GRPWS-4824T 120/208-240 2574 14.3 NEMA 14-20P 227 lbs. (103 kg)

220-230 (CE) 2301-2514 10.5-10.9 CEE 7/7 Schuko 227 lbs. (103 kg)

230-240 (CE) 2514-2738 10.9-11.4 BS-1363 227 lbs. (103 kg)

DUAL SHELF

Model Width Depth Height†

(A) (B) (C)

GRPWS-2418D 24" 18" 22½"

(61 cm) (46 cm) (57 cm)

GRPWS-3618D 36" 18" 22½"

(91 cm) (46 cm) (57 cm)

GRPWS-4818D 48" 18" 22½"

(122 cm) (46 cm) (57 cm)

GRPWS-2424D 24" 24" 23½"

(61 cm) (61 cm) (60 cm)

GRPWS-3624D 36" 24" 23½"

(91 cm) (61 cm) (60 cm)

GRPWS-4824D 48" 24" 23½"

(122 cm) (61 cm) (60 cm)

SPECIFICATIONS

4

Form No. GRPWSM-1001

TRIPLE SHELF

Model Width Depth Height†

(A) (B) (C)

GRPWS-2418T 24" 18" 29¾"

(61 cm) (46 cm) (76 cm)

GRPWS-3618T 36" 18" 29¾"

(91 cm) (46 cm) (76 cm)

GRPWS-4818T 48" 18" 29¾"

(122 cm) (46 cm) (76 cm)

GRPWS-2424T 24" 24" 30¾"

(61 cm) (61 cm) (78 cm)

GRPWS3624T 36" 24" 30¾"

(91 cm) (61 cm) (78 cm)

GRPWS4824T 48" 24" 30¾"

(122 cm) (61 cm) (78 cm)

A

B

C

† Height includes 4" (10 cm) for legs.

† Height includes 4" (10 cm) for legs.

DIMENSIONS - GRPWS MODELS

A

B

C

SPECIFICATIONS

INSTALLATION

5

Form No. GRPWSM-1001

† Height includes 4" (10 cm) for legs.

QUADRUPLE SHELF

Model Width Depth Height†

(A) (B) (C)

GRPWS-2418Q 24" 18" 36¾"

(61 cm) (46 cm) (93 cm)

GRPWS-3618Q 36" 18" 36¾"

(91 cm) (46 cm) (93 cm)

GRPWS-4818Q 48" 18" 36¾"

(122 cm) (46 cm) (93 cm)

GRPWS-2424Q 24" 24" 37¾"

(61 cm) (61 cm) (96 cm)

GRPWS-3624Q 36" 24" 37¾"

(91 cm) (61 cm) (96 cm)

GRPWS-4824Q 48" 24" 37¾"

(122 cm) (61 cm) (96 cm)

A

B

C

ALL MODELS

Glo-Ray Pizza Warmers are shipped with most
components pre-assembled. Care should be taken when
unpacking shipping carton to avoid damage to unit and
components enclosed.

1. Remove unit from box.

2. Remove information packet. To prevent delay in

obtaining warranty coverage, fill out and mail in
the warranty card.

3. Remove tape and protective packaging from all
surfaces of unit.

4. Carefully lay unit on its side and install the four legs
as shown in Figure 3. Hand tighten legs until snug.

CAUTION
The National Sanitation Foundation (NSF) requires
that GRPWS Series units over 36" (91 cm) in length
or weighing more than 80 lbs. (36 kg) to be either
sealed or raised on the installation surface. If this
unit cannot be sealed at the point of use, 4" (10 cm)
legs are included to allow for proper cleaning
access below unit. See Hatco Accessories for
installation instructions.

Figure 3. Leg Installation

MODELS WITH 4" (10 CM) ADJUSTABLE LEGS

5. Carefully lay unit on its side. Install legs to bottom
of unit as shown in Figure 3. Hand tighten legs until
snug. Do not overtighten. Return unit to the upright
position.

INSTALLATION

OPERATION

6

Form No. GRPWSM-1001

NOTE: Legs are adjustable for leveling the unit. Use a
5/8" (16 mm) open-end wrench to make leveling
adjustments once the unit is placed in final position.

6. Slide each side glass panel into the upper channel,
then lower the panel into the lower channel.
See Figure 4.

7. Each unit is supplied with a stainless steel box stop
for each shelf. To install, place the box stop in the
holding brackets and twist down until secure.
See Figure 5.

LOCATION

NOTE: The unit must be transported in the
upright position.

For proper operation and maximum performance, locate
the Pizza Warmer in an area where the ambient air
temperature is constant and is a minimum of 70° F
(21° C). Areas which are susceptible to active air
movements or currents should be avoided, i.e., near
exhaust fans or hoods and air conditioning ducts.

WARNING
For safe and proper operation, the unit must be
located a reasonable distance from combustible walls
and materials. If safe distances are not maintained,
discoloration or combustion could occur.

CAUTION
Locate the unit at the proper counter height, in an
area that is convenient for use. The location should
be level to prevent the unit or its contents from
accidentally falling, and strong enough to support
the weight of the unit and food displayed.

Figure 4. Side Glass Panel Installation

Figure 5. Box Stop Installation

Each shelf on the unit is controlled by an ON/OFF
switch and thermostat control. See Figure 6. The switch
for each shelf must be in the ON position for that shelf
to function. The thermostat control for each shelf can be
set to any desired heating level as indicated on the
control plate.

CAUTION
Some exterior surfaces on the unit will get hot. Use
caution when touching these areas to avoid injury.

ON/OFF Switch

Thermostat Control

Figure 6. Controls

MAINTENANCE

7

Form No. GRPWSM-1001

GENERAL

Hatco Glo-Ray Pizza Warmers are designed for
maximum durability and performance, with
minimum maintenance.

WARNING
To avoid any injury, turn the power switches off,
unplug the unit from the power source and allow to
cool before performing any maintenance.

WARNING
To avoid electrical shock or personal injury, do not
steam clean or use excessive water on the unit.

WARNING
Unit is not waterproof. DO NOT submerge in water.
Do not operate if it has been submerged in water.

CLEANING

CAUTION
Use only non-abrasive cleaners. Abrasive cleaners
could scratch the finish marring its appearance and
making it susceptible to dirt accumulation.

To preserve the bright finish of the Glo-Ray Pizza
Warmer, it is recommended that the exterior and interior
surfaces be wiped daily with a damp cloth. Stubborn
stains may be removed with a good non-abrasive
cleaner. Hard to reach areas should be cleaned with a
small brush and mild soap.

Clean the glass sides using a common glass cleaner.

DISPLAY LIGHT BULB REPLACEMENT

The display light is an incandescent light bulb which
illuminated the warming area. The bulb has a special
coating to guard against injury and food contamination
in the event of breakage.

1. To replace a light bulb, disconnect the power supply
and wait until the unit has cooled.

2. Light bulbs have a threaded base. Unscrew the light
bulb from the unit and replace it with a new
specially coated incandescent light bulb.

NOTE: Hatco shatter-resistant light bulbs meet N.S.F.
standards for food holding and display areas. For 120,
120/208 and 120/240 Volt applications, use Hatco part
#02.30.043.00. For 220-230 or 230-240 Volt
applications, use Hatco part #02.30.058.00.

WARNING
Only light bulbs which meet or exceed N.S.F.
standards, specifically designed for food holding
areas must be used. Breakage of light bulbs not
specially coated could result in personal injury
and/or food contamination.

WARNING
If service is required on this unit, contact your
Authorized Hatco Service Agent, or contact the
Hatco Service Department at 800-558-0607 or
414-671-6350; fax [phone] or International
fax [phone].

WARNING
This product has no “user” serviceable parts. To
avoid damage to the unit or injury to personnel, use
only Authorized Hatco Service Agents and Genuine
Hatco Replacement Parts when service is required.

WARNING
Genuine Hatco Replacement Parts are specified to
operate safely in the environments in which they are
used. Some aftermarket or generic replacement parts
do not have the characteristics that will allow them
to operate safely in Hatco equipment. It is essential
to use Hatco Replacement Parts when repairing
Hatco equipment. Failure to use Hatco Replacement
Parts may subject operators of the equipment to
hazardous electrical voltage, resulting in electrical
shock or burn.

ACCESSORIES

8

Form No. GRPWSM-1001

TEMPERATURE INDICATING
DISPLAY (TID)

NOTE: This accessory is factory installed only, not
available for retrofit.

Units maybe equipped with temperature indicating
displays which show the current base temperature of
each shelf.

BOTTOM

MIDDLE

TOP

Figure 7. Controls for Triple Shelf Unit with TID.

ON/OFF Switch

Temperature Indicating Display

Thermostat Control

HATCO LIMITED WARRANTY

9

Form No. GRPWSM-1001

1. PRODUCT WARRANTY

Hatco warrants the products that it manufactures (the
“Products”) to be free from defects in materials and
workmanship, under normal use and service, for a
period of one (1) year from the date of purchase
when installed and maintained in accordance with
Hatco’s written instructions. Buyer must establish the
product’s purchase date by returning Hatco’s
Warranty Registration Card or by other means
satisfactory to Hatco in its sole discretion.

Hatco warrants the following Product components to
be free from defects in materials and workmanship
from the date of purchase (subject to the foregoing
conditions) for the period(s) of time and on the
conditions listed below:

a) One (1) Year Parts and Labor PLUS One (1)

Additional Year Parts-Only Warranty:

Toaster Elements (metal sheathed)
Drawer Warmer Elements (metal sheathed)
Drawer Warmer Drawer Rollers and Slides
Food Warmer Elements (metal sheathed)
Infra-Black®Elements (metal sheathed)
Display Warmer Elements (metal sheathed air heating)
Holding Cabinet Elements (metal sheathed air heating)
Cook and Hold Oven Elements (metal sheathed)

b) One (1) Year Parts and Labor PLUS Four (4)

Additional Years Parts-Only Warranty on
pro-rated terms that Hatco will explain at
Buyer’s Request:

Powermite

®

Gas Booster Heater Tanks
Mini Compact Tanks (stainless steel)
3CS and FR Tanks

c) One (1) Year Parts and Labor PLUS Four (4)

Additional Years Parts-Only Warranty PLUS
Five (5) Year Parts-Only Warranty on pro­rated terms that Hatco will explain at Buyer’s
Request:

Booster Heater Tanks (Castone

®

)

d) One (1) Year Parts-Only Warranty for

components not installed by Hatco:

Accessory Components (including but not
limited to valves, gauges and remote switches)

THE FOREGOING WARRANTIES ARE
EXCLUSIVE AND IN LIEU OF ANY OTHER
WARRANTY, EXPRESSED OR IMPLIED,
INCLUDING BUT NOT LIMITED TO ANY
IMPLIED WARRANTY OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE OR
PATENT OR OTHER INTELLECTUAL
PROPERTY RIGHT INFRINGEMENT. Without
limiting the generality of the foregoing, SUCH
WARRANTIES DO NOT COVER: Coated
incandescent light bulbs, fluorescent lamps, lamp
warmer heat bulbs, glass components or Product
failure in booster tank and fin tube heat exchanger
caused by liming, sediment buildup, chemical attack
or freezing in tanks, Product misuse, tampering or
misapplication, improper installation, application of
improper voltage, or recalibration of thermostats or
high limit switches.

2. LIMITATION OF REMEDIES AND
DAMAGES

Hatco’s liability and Buyer’s exclusive remedy
hereunder will be limited solely, at Hatco’s option,
to repair or replacement by a Hatco-authorized
service agency (other than where Buyer is located
outside of the United States or Canada, in which case
Hatco’s liability and Buyer’s exclusive remedy
hereunder will be limited solely to replacement of
part under warranty) with respect to any claim made
within the applicable warranty period referred to
above. Without limiting the generality of the
foregoing, all portable Products (as defined in N.S.F.
4-4.28.4) shall be delivered by Buyer, at its sole
expense, to the nearest Hatco-authorized service
agency for replacement or repair. Hatco reserves the
right to accept or reject any such claim in whole or in
part. Hatco will not accept the return of any Product
without prior written approval from Hatco, and all
such approved returns shall be made at Buyer’s sole
expense. HATCO WILL NOT BE LIABLE, UNDER
ANY CIRCUMSTANCES, FOR CONSEQUENTIAL
OR INCIDENTAL DAMAGES, INCLUDING BUT
NOT LIMITED TO LABOR COSTS OR LOST
PROFITS RESULTING FROM THE USE OF OR
INABILITY TO USE THE PRODUCTS OR FROM
THE PRODUCTS BEING INCORPORATED IN OR
BECOMING A COMPONENT OF ANY OTHER
PRODUCT OR GOODS.

HATCO CORPORATION

P.O. Box 340500, Milwaukee, WI 53234-0500 U.S.A.

[phone] [phone]

Parts & Service Fax [phone] Int’l. Fax [phone]

www.hatcocorp.com

Part No. 07.04.315.00 Form No. GRPWSM-1001

Printed in U.S.A. October 2001

HATCO AUTHORIZED PARTS DISTRIBUTORS

ALABAMA

Jones McLeod Appl. Svc.
Birmingham 205-251-0159

ARIZONA

Auth. Comm. Food Equip.
Phoenix 602-234-2443

Byassee Equipment Co.
Phoenix 602-252-0402

CALIFORNIA

Industrial Electric
Huntington Beach 714-379-7100

Chapman Appl. Service
San Diego 619-298-7106

P & D Appliance
S. San Francisco 650-635-1900

COLORADO

All City Service
Denver 303-454-9500

Hawkins Commercial Appliance
Englewood 303-781-5548

DELA

WARE

Food Equipment Service
Wilmington 302-996-9363

FLORIDA

Whaley Foodservice Repair
Jacksonville 904-725-7800
Nass Service Co., Inc.
Orlando 407-425-2681
B.G.S.I.
Pompano Beach 954-971-0456
Comm. Appliance Service
Tampa 813-663-0313

GEORGIA

Southeastern Rest. Svc.
Norcross 770-446-6177

HA

W

AII

Burney’s Comm. Service, Inc.
Honolulu 808-848-1466

Food Equip Parts & Service
Honolulu 808-847-4871

ILLINOIS

Parts Town
Broadview 708-865-7278

Eichenauer Elec. Service
Decatur 217-429-4229
Midwest Elec. Appl. Service
Elmhurst 630-279-8000
Cone’s Repair Service
Moline 309-797-5323

INDIANA

Comm. Parts & Service, Inc.
Indianapolis 317-545-9655

IOW

A

Electric Motor Service Co.
Davenport 319-323-1823

KENTUCKY

Comm. Parts & Service, Inc.
Louisville 502-367-1788

LOUISIANA

Chandlers Parts & Service
Baton Rouge 225-272-6620

LOUISIANA (Continued)

Bana Comm. Parts, Inc.
Shreveport 318-631-6550

MAR

YLAND

Electric Motor Service
Baltimore 410-467-8080

GCS Service, Inc.
Silver Spring 301-585-7550

MASSACHUSETTS

Ace Service Co., Inc.
Needham 781-449-4220

MICHIGAN

Commercial Kitchen Service
Bay City 517-893-4561

Bildons Appliance Service
Detroit 248-478-3320

Midwest Food Equip. Service
Grandville 616-261-2000

MINNESOT

A

GCS Service
Minneapolis 612-546-4221

MISSOURI

GCS Service, Inc.
Kansas City 816-920-5999

Commercial Kitchen Services
St. Louis 314-890-0700

Kaemmerlen Parts & Service
St. Louis 314-535-2222

NEBRASKA

Anderson Electric
Omaha 402-341-1414

NEV

ADA

Burney’s Commercial
Las Vegas 702-736-0006
Hi. Tech Commercial Service
N. Las Vegas 702-649-4616

NEW JERSEY

Jay Hill Repair
Fairfield 973-575-9145

Service Plus
Flanders 973-691-6300

NEW YORK

Acme American Repairs, Inc.
Brooklyn 718-456-6544
Alpro Service Co.
Brooklyn 718-386-2515
Appliance Installation
Buffalo 716-884-7425
Northern Parts Dist.
Plattsburgh 518-563-3200
J. B. Brady, Inc.
Syracuse 315-422-9271

NORTH CAROLINA

Authorized Appliance
Charlotte 704-377-4501

OHIO

Akron/Canton Comm. Svc. Inc.
Akron 330-753-6635

Certified Service Center
Cincinnati 513-772-6600

GCS Service
Columbus 614-476-3225

OHIO (Continued)

Electrical Appl. Repair Service
Independence 216-459-8700
E. A. Wichman Co.
Toledo 419-385-9121

OKLAHOMA

Hagar Rest. Service, Inc.
Oklahoma City 405-235-2184

Krueger, Inc.
Oklahoma City 405-528-8883

OREGON

Bressie Electric Co.
Portland 503-231-7171

Ron’s Service, Inc.
Portland 503-624-0890

PENNSYL

VANIA

Authorized Factory Service
Coraopolis 412-262-2330

FAST Comm. Appl. Service
Philadelphia 215-288-4800

GCS Service, Inc.
Pittsburgh 412-787-1970

K & D Service Co.
Harrisburg 717-236-9039

Elmer Schultz Services
Philadelphia 215-627-5401

Electric Repair Co.
Reading 610-376-5444

RHODE ISLAND

Marshall Electric Co.
Providence 401-331-1163

SOUTH CAROLINA

Whaley Foodservice Repair
W. Columbia 803-791-4420

TENNESSEE

Camp Electric
Memphis 901-527-7543

TEXAS

City Kitchen Service Co.
Austin 512-719-4445

Stove Parts Supply
Fort Worth 817-831-0381

Armstrong Repair Service
Houston 713-666-7100

Commercial Kitchen Repair Co.
San Antonio 210-735-2811

San Antonio Rest. Equip.
San Antonio 210-532-1660

UT

AH

Peterson’s Commercial Parts & Svc.
Salt Lake City 801-487-3653

VIRGINIA

Daubers
Norfolk 757-855-4097

Daubers
Springfield 703-866-3600

W

ASHINGTON

Restaurant Appl. Service
Seattle 206-524-8200

WISCONSIN

A.S.C., Inc.
Madison 608-246-3160

A.S.C., Inc.
Milwaukee 414-543-6460