Hatco FTB-1 User Manual
Drop-In Frost Tops
Models: FTB-1, -2, -3, -S2, -S3
Hatco Drop-in Frost Tops keep pre-chilled beverages,
snacks, hors d’oeuvres and side dishes cool and ready to
serve. Also available in a Slim Line Series, providing wider
access to your customer, regardless of the
sneeze guards.
Standard features
• Available in one-, two and three-pan models, as well as twoand three-pan slim congurations
• Accommodates full-size and half-size sheet pans
• NSF 7 approved cold wall construction utilizes R-404A
refrigerant keeping food product cold without drying it out
• Auto-defrost is activated through an advanced electronic
controller programmed at the customer location
• 1" NPT drain (excluding FTB-1)
• Matches the Hatco line of Heated Wells for an integrated look
• The condensing unit, mounted on the center of the unit, rotates
180° (movable in some models)
• Electronic adjustable temperature control is available to mount
on either side of the condensing unit or remotely mounted up to
4' (1219 mm) from the unit (cannot be mounted over the
condensing coil)
• Mobile condensing unit can be moved in 3" (76 mm) increments
in the FTB-2 and 6.5" (165 mm) increments in the FTB-3, -S2,
-S3 (see drawing on page 2)
• Long, exible refrigerant line (ability to pullout condensing unit)
for service
Project
Item #
Quantity
FTB-S2 with
accessory sheet pans
FTB-2
FTB-3 with accessory
sheet pans
Options
c
Additional Four-Year Parts Only Warranty on Compressor
(available at time of purchase only)
Accessories
c
Full-Size Pan (18"W x 13"D [457 x 330 mm])
c
Half-Size Pan (18"W x 26"D [457 x 660 mm])
HATCO CORPORATION
(800) 558-0607
Form No. FTB Spec Sheet Page 1 of 3 August 2015
(414) 671- 6 3 50
l
l
www.hatcocorp.com
l
P.O. Box 340500 Milwaukee, WI 53234-0500 U.S.A.
l
equipsales@hatcocorp.com
intlsales@hatcocorp.com
l
Condensing unit
rotates up to 180°
if located at center of
unit or closer to coil inlet.
Condensing Unit:
FTB-1 is not moveable
FTB-2 moveable from
left to right in 3" (76 mm)
increments and FTB-3 in
6.5" (165 mm) increments.
Control Assembly may
be moved to any area
within 48" (1219 mm)
of compressor
No drain on FTB-1
.84"
(21 mm)
16.71"
(424 mm)
.5"
(13 mm)
3.06"
(77 mm)
FTB-1: 21.06" (535 mm)
FTB-2: 39" (991 mm)
FTB-3: 57" (1448 mm)
.84"
(21 mm)
FTB-1,-2,-3: 28.94" (735 mm)
17.21"
(437 mm)
FRONT VIEW
SIDE VIEW
Drop-In Frost Tops
Models: FTB-1, FTB-2, FTB-3, FTB-S2, FTB-S3
Ordering Instructions:
Please specify the following with
each order:
1. Desired Voltage:
120 or 220-240V
2. Number of Full-Size
Sheet Pans Accommodated:
1-, 2-, 3-pan as rectangular,
sheet pans with Slim or Standard conguration
Model FTB-1, -2, -3
17.21"
(437 mm)
.84"
(21 mm)
16.71"
(424 mm)
Model FTB-S2, -S3
17.21"
(437 mm)
(424 mm)
16.71"
.84"
(21 mm)
3. Electronic Control Assembly can be
mounted on either side of the Condensing
Unit or remotely mounted up tp 4 feet
(1219 mm) from the unit (cannot be
mounted over the condensing unit)
FTB-1: 21.06" (535 mm)
FTB-2: 39" (991 mm)
FTB-3: 57" (1448 mm)
FRONT VIEW
FTB-S2: 54.94" (1395 mm)
FTB-S3: 80.81" (2053 mm)
No drain on FTB-1
FRONT VIEW
3.06"
(77 mm)
.5"
(13 mm)
Control Assembly may
be moved to any area
within 48" (1219 mm)
of compressor
Condensing unit
rotates up to 180°
if located at center of
unit or closer to coil inlet.
Condensing Unit:
FTB-1 is not moveable
FTB-2 moveable from
left to right in 3" (76 mm)
increments and FTB-3 in
6.5" (165 mm) increments.
Note: Condensing unit
moveable from
left to right in 6.5"
(165 mm) increments.
Condensing Unit
rotates up to 180°
if located at center or unit
or closer to coil inlet
3.06"
(77 mm)
.5"
(13 mm)
Control Assembly may
be moved to any area
within 48" (1219 mm)
of compressor
FTB-1,-2,-3: 28.94" (735 mm)
FTB-S2,-S3: 21.06" (535 mm)
SIDE VIEW
.84"
(21 mm)
.84" (21 mm)
SIDE VIEW
(800) 558-0607
HATCO CORPORATION
(414) 671- 6 3 50
l
l
www.hatcocorp.com
l
P.O. Box 340500 Milwaukee, WI 53234-0500 U.S.A.
l
equipsales@hatcocorp.com
intlsales@hatcocorp.com
l
Form No. FTB Spec Sheet Page 2 of 3 August 2015
Loading...