Hashima i500 Series User Manual
The i500 Series
Professional Steam
Products
INSTRUCTION MANUAL
USER INSTRUCTIONS i500
Thank you for purchasing the Reliable™ i500 series iron system. Please
follow the instructions carefully. With proper care and maintenance, your
steamer will provide years of dependable service.
1. Remove the ironing station from its packing and make sure all packing
parts have been taken off (including the protection bags). Lay the
station on a flat and steady surface fitted to support it next to a wall
socket (max. mt. 1,5).
2. It is recommended to lay the iron on the supplied pad.
3. Insert in the right seat (2) the small supplied wand to hold the hose up
and hook it with the spring up to the iron-boiler connecting wire.
4. Unscrew the safety cap (1) and let the internal air out. Fill the boiler
with: Max. 2,0 litres of water for model i500
Use the funnel supplied, making sure you do not overfill the tank.
5. Insert the plug into the main supply point; switch on boiler (4) and iron
button (3). If the two buttons come on, iron and boiler are working.
6. Turn the iron plate’s temperature regulating knob (6) to the position
“cotton °°°” (indicated on the iron knob).
7. Wait that the boiler button’s red light (4) goes off (it takes about 10
minutes). While ironing, the boiler button’s red light normally comes on.
8. The machine is ready for use.
9. Push the steam button (7).
10. It is possible to regulate the quantity of steam by the steam knob (8).
11. In case the steam stops during ironing and the water button’s red light
(5) comes on, it means that there is not enough water in the tank. To
start ironing again, switch off the boiler button (4); press the steam iron
button (7) to ensure there is no more steam in the boiler, slowly open
the pressure cap (1) and refill to the required level with warm water.
Replace the cap and wait for it to build up pressure again.
12. When you first press the steam button (after having turned the boiler
on and depressed the steam button on the iron) you might notice a
decrease in pressure. This is because the tank has air in it. In order to
have plenty of steam (after you have depressed the iron) wait until the
pressure goes back up to the maximum level before you begin.
IMPORTANT
When you are finished using the boiler for the day, unscrew the fill cap oneturn on the unit to release the steam/air from the tank. This will eliminate the
vacuum that may cause damage to the pressure gauge.
COMPONENTS
1. Safety cap
2. Wand to hold mono-hose up
3. Iron power button
4. Boiler power button
5. Low water level light indicator
6. Temperature regulating knob
7. Steam button
8. Steam regulation knob
9. Manometer / pressure gauge
CAUTION
• Do not leave the machine unattended while the plug is connected to
the socket.
• The iron reaches very high temperatures and it keeps being very hot
even 15 minutes after it’s been switching off. Be careful not to burn
yourself.
• For complete safety, before filling the boiler, please disconnect the
plug.
• While using the machine, never unscrew or remove the cap while
under pressure (1). Before removing it, make sure that it does not
give off steam anymore by shutting the boiler off, and pressing the
steam iron button (7) to release all remaining steam.
• The machine has a special heating element. Only qualified
technician should replace it.
• The safety cap (1) must be replaced with original parts only.
TECHNICAL DATA
Adjustable iron thermostat set from 60°C to 215°C
Bimetallic safety iron thermostat with manual reset at 275°C
Full aluminium-plated heating element at 800W – 120V
Boiler power i500: 1000W
Working pressure i500: 3,5 bar
Tank nominal capacity of model i500: 2.5 litres
TROUBLESHOOTING
PROBLEM
EXPLANATION
SOLUTION
Does
steam go
out from
the boiler?
It may happen that, while filling the
tank, some water overfills the cap and
flows inside the boiler wetting the
insulating material
In order to solve the problem, we suggest
using the machine as usual so that the
insulating material dries up in about one
hour through the heat of the machine. In
case you still have this problem after one
working hour, please contact the service
centre.
Does the
steam iron
leak steam
mixed with
water?
1) While filling the tank you may have
poured too much water into it.
2) The iron plate has to be hot before
the steam passage
1) The problem will go on until the excess
water is emptied. Keep the steam button
depressed until the water in the tank is at
the correct level.
2) Please check that the temperature knob
is on the right position: “cotton °°°)”
There is
no steam
coming out
of the
iron?
1) The steam knob (where supplied)
might be closed
2) The iron switch might be off
3) The boiler switch might be off
4) The water might be used up.
1) Open the steam knob anticlockwise.
2) After the iron switch comes on, wait for 4
minutes so that the iron plate gets hot.
3) After the boiler switch comes on, wait for
10 minutes so the boiler produces steam.
4) Fill it following the instructions carefully.
Does the
ironing
board get
wet?
1) The ironing board cover might not
be able to absorb the steam
completely
2) The steam iron leaks steam mixed
with water (Check by spraying some
steam on a dry cloth)
1) You might use a thicker cover (or two
covers) so to create a thicker surface to
absorb the steam better. In case you are
using a vacuum table, switch on the
vacuum function each time you are using
the steam
2) See # 2
Does the
steam leak
dirty
water?
Some dirty might have gone into the
tank with the water and it is given off
from the iron.
Fill the empty tank with 1 liter of water,
screw the cap up, shake it, unscrew the
cap and empty the tank. Repeat the action
until the water is cleaned. We do not
recommend the use of any additive to pour
in the tank. Before ironing again spray
some steam on a cloth until clean steam
comes out.
i500 SPARE PARTS LISTS
ITEM
NR
DESCRIPTION
AC004
1
BOX
AST114
2
FAIRLEAD FOR HEATING ELEMENT
CD332
1
HANDLE
CD332/2
1
HEXAGONAL HEADED SCREW FOR HANDLE
CD338/1
1
NUT FOR WAND SUPPOR T
CD338/2
1
WASHER FOR STICK SUPPORT
CD338/3
1
WAND SUPPORT
CD339/1
1
TANK
CD343/110
1
COPPER HEATING ELEMENT 1000 W - 120V
CD342
1
TEFLON O-RING FOR THE HEATING ELEMENT
CD346/35
1
PRESSURE SWITCH WITH RESET SET 2,5 BAR
CD347
1
FAIRLEAD FOR CAP CONNECTION
CD347/7000
1
SOLENOID VALVE FAIRLEAD
CD348
1
BULB THERMOSTAT 165°
CD348/1
1
SCREW FOR BULB THERMOSTAT
CD349
1
BIPOLAR SWITCH 16A
CD350
1
RED PILOT LIGHT 120/240V
CD351
1
CONNECTOR
CD353
4
4 POLE TERMINAL BOARD PA 21 TO FASTON
CD356
1
MONOHOSE MT. 2,2 5X10
CD360
1
FAIRLEAD STOP 6W-1
CD361
1
FAIRLEAD STOP 6N3
CD364
1
IRON PAD
CD365/4
1
MALE SAFETY CAP 3/8
CD366/6
1
O-RING FOR SAFETY CAP
CD367
1
DYN SMALL FOOT
CD368
1
STICK FOR MONOHOSE
CD368/1
1
SPRING
CD368/2
1
CLAMP FOR SPRING
CD369
1
FUNNEL DIAMETER 10 FOR ITEM 013
GV028/84/110
1
ADJUSTABLE SOLENOID VALVE 120V
CD374
1
GAUGE FOR 06-09/D
CD376
1
MUSHROOM-SHAPED SMALL CAP FOR IRON REST
CD377
1
ANTI-UNSCREWING SCREW 35x5
CD378
1
HOSE CLAMP 10/12
CD378/1
1
HOSE CLAMP 9/1
CD380/110
1
WIRING 120V
CD382
1
GLASS WOOL INSULATING
CD384
1
3 WAY RECEPTACLE 1/4 CONICAL 1/4 FEMALE 1/8 FEMALE
CD458
4
TECHNICAL DATA LABEL
CD458/1
1
SMALL TECHNICAL DATA LABEL
CD471
1
LOWER STAINLESS CHASSIS
CD473/1
1
FRONT STAINLESS CHASSIS
CD476
1
BACK STAINLESS CHASSIS
CD477
1
STAINLESS UPPER BODY
CD490
1
ANGLE CONNECTION
CD492
1
INSTRUCTIONS MANUAL
CV103
1
NUT 1/4 FOR SOLENOID VALVE 7000
CV114
1
IRON PACKING
CV177
1
KNOB 120V
FS002/110
1
PLATE
FS003
1
ADJUSTABLE THERMOSTAT
FS004
1
THERMOSTAT WITH MANUAL RESET
FS005
1
KORK HANDLE
FS006
1
BRACKET
ITEM
NR
DESCRIPTION
FS007
1
IRON COVER
FS009
1
WIRING 16AWG
FS011
1
INSERTION
FS012
1
SCREW FOR THERMOSTAT
FS012
5
SCREW FOR THERMOSTAT
FS014
3
SCREW FOR BACK HANDLE
FS015
2
SCREW FOR MICRO SWITCH
FS016
1
SCREW FOR MICRO SWITCH CASE
FS017
2
SCREW FOR HANDLE FIXING
FS018
3
SCREW FOR TERMINAL BLOCK STOP
FS019
1
HANDLE COVER
FS020
1
BACK HANDLE
FS021
1
BUTTON HOLDER
FS022
1
BUTTON CASE
FS023
1
UPPER IRON BUTTON
FS024
1
LOWER IRON BUTTON
FS025
1
PLAQUE FOR BRACKET
FS026
1
CABLE PRESS
FS027
1
FRONT HANDLE HOLDER
FS028
1
BACK HANDLE HOLDER
FS030
2
SCREW CAPS
FS031
2
BRASS WASHER
FS032
2
BRASS SPACER
FS033
1
MICRO SWITCH
FS035
4
UNDER SCREW
FS037
1
SPHERE FOR KNOB
FS038
2
WASHER FOR HANDLE
FS039
1
WASHER FOR KNOB
FS041
1
FAIRLEAD FOR POWER CORD
FS057
1
SPRING
FS058
0,03
COATED
FS060
2
WASHER
GV025/23
8
NUT
GV025/27
7
WASHER
GV025/51
1
COPPER PIPE
GV026/7
1
FEMALE QUICK RELEASE
GV026/9
1
QUICK RELEASE
GV028/30
1
L. JOINT
GV028/31
1
L. JOINT
GV028/36
1
ILME FEMALE SOCKET GROUP
GV028/38
1
ILME MALE SOCKET GROUP
GV028/39
1
REMOVABLE COVER
GV028/40
1
CABLE PRESS
GV028/45
1
COVER WITH ROD
GV028/52
6
SCREW
GV028/6
1
L. JOINT
GV669
1
BOX
GV671
1
INSTRUCTIONS MANUAL
MC016/110
1
POWER CORD 110V
RIC003
1
TERMINAL BLOCK
RIC003/2
1
CERAMIC TERMINAL BOARD 120V
i500 PARTS DRAWING
~
I
AR
T. i
500/i30
~,,,,.
~
~RELIABLE
~,.~
~
~
~
I
0/110
Cllli.lilO
CD.160
M
I
~
Loading...