Hasbro LAZER TAG BLAST User Manual
GETTING STARTED
STEP 1: BATTERY INSTALLATION
1)To install batteries, use a Phillips head screwdriver to open the battery door.
SCREW (coin types plus phillips head)
2)Insert 6 x 1.5V "AA" batteries (or equivalent) making sure to align the "+" and "-" as shown. Tiger recommends DURACELL® Batteries for optimum performance.
1
3)To ensure proper function:
a)Do not mix old and new batteries
b)Do not mix alkaline, standard or rechargeable batteries
c)Battery insertion should be done by an adult
d)Non-rechargeable batteries are not to be recharged
e)Rechargeable batteries are to be removed from the toy before being charged (if removable)
f)Rechargeable batteries are only to be charged under adult supervision (if removable)
g)Only batteries of the same or equivalent type as recommended are to be used
h)Batteries are to be inserted with the correct polarity
i)Exhausted batteries are to be removed from the toy
j)The supply terminals are not to be short-circuited
2
STEP 2: USING YOUR B.LA.S.T. UNIT
Your Lazer TagTM B.L.A.S.T. has been designed with performance and features to ensure exciting actionpacked games.
LAZER TAGTM B.L.A.S.T.
On/Off switch
LED Sight
Mute Button
Trigger |
|
LED Score |
|
|
Display |
Folding Stock |
|
|
|
||
Super Strike |
TM |
Force FieldTM |
|
|
Button |
|
|
Button |
|
Integrated 360˚ |
|
|
|
Lazer sensor
Mortar Trigger
Retractable
Mortar Legs
3
1)On/Off switch: Turns the B.L.A.S.T. on and off.
2)Mute Button: Toggles the warning beeps on and off. Turn them off for Stealth attacks.
3)Integrated 360 degree Lazer sensor (can detect a tag from 360 degrees). This detects the incoming Lazer beams from your opponent’s weapons.
4)Trigger: Squeeze once for a single shot, hold it down for rapid fire.
5)Mortar Trigger: Use to fire the B.L.A.S.T. when it’s in Mortar Mode. When you press it the Mortar will fire, a few seconds later its beams will be emitted. These few seconds are all the time your enemy has to run for cover. Note; the other trigger is not used in Mortar mode.
6)LED Score Display: This counter shows how many tags you have remaining. When the B.L.A.S.T. is turned on, you will have ten tags remaining, this is displayed as “0”. Each time your are hit you lose one tag. The B.L.A.S.T.’s voice warning system will tell you when you have two tags or one tag remaining. When you have been tagged ten times, you are out of the game. Turn the B.L.A.S.T. on and off again to reset it.
4
7)Retractable Mortar Legs: When in Rifle and Bazooka Mode, the Retractable Mortar legs must be folded and locked against the body of the B.L.A.S.T.. In Mortar Mode they should be folded out and locked in order to support the Blast.
8)Folding Stock: In Rifle mode the folding stock should be down, in Bazooka mode it should be folded and flush with the body of the B.L.A.S.T.. The folding Stock is not used in Mortar mode.
9)LED Sight: Gives you pinpoint accuracy. Line up the red dot in the sight with your opponent’s target and fire away.
10)Force FieldTM Button: Activating the B.L.A.S.T.’s ForceFieldTM will momentarily protect you from being tagged by the enemy. You will hear the ForceFieldTM’s sound effect while it is on. You get three ForceFieldsTM per game (10 Tags).
11) Super StrikeTM Button: One SuperStrikeTM has the power of ten tags. Score a direct hit on an opponent with the SuperStrikeTM and that player is out of the game. You get one SuperStrikeTM per game (10 tags) so use it wisely.
5
CONFIGURATIONS
The B.L.A.S.T. can be configured three different ways; Rifle mode, Bazooka mode, and Mortar mode. You can use these different modes to assure victory in All Situations Tactical. Do not turn the B.L.A.S.T. on and off when changing configurations, it should be left on so your number of tags is retained.
Rifle Mode
When in Rifle Mode, the B.L.A.S.T. emits a highly accurate beam with which you can tag opponents at ranges up to 350 feet. Use Rifle mode for long range attacks and sniper operations. To configure the B.L.A.S.T. for rifle mode;
6
Loading...