Hasbro 79037, 79040 User Manual

CR2032
A76/LR44
PRODUCTS THAT DO NOT INCLUDE BATTERIES:
Products that do NOT include but require AAA, AA, C, D, 9V batteries should declare that alkaline ("LR") type batteries are recommended.
Motorized products that do NOT include but require AAA, AA, C, D, batteries should declare that alkaline ("LR") type batteries
are required.
PRODUCTS THAT INCLUDE BATTERIES:
Products that include AAA, AA, C, D, 9V batteries should declare that batteries are included and recommend replacement with alkaline batteries.
Motorized products that include AAA, AA, C, D, 9V batteries should declare that batteries are included and replacement with alkaline
batteries is required.
BATTERIES REQUIRED
x3
1.5VA AA R03 size
Alkaline batteries recommended. Phillips/cross head screwdriver (not included) needed to insert batteries.
NOT INCLUDED
x3
BATTERIES REQUIRED
1.5VA AA/R03 size
Alkaline batteries recommended.Phillips/cross head screwdriver (not included) needed to insert batteries.
NOT INCLUDED
BATTERIES REQUIRED
x3
1.5VA AA/R03 size
Alkaline batteries recommended. Phillips/cross head screwdriver (not included) needed to insert batteries.
NOT INCLUDED
BATTERIES REQUIRED
x3
1.5VA AA R03 size
Alkaline batteries recommended. Phillips/cross head screwdriver (not included) needed to insert batteries.
NOT INCLUDED
BATTERIES INCLUDED
x3
1.5VA AA/R03 size
Replace with 3 x 1.5V AAA or R03 size batteries. Alkaline batteries recommended. Phillips/cross head screwdriver (not included) needed to insert batteries.
x3
BATTERIES INCLUDED
1.5VA AA/R03 size
Replace with 3 x 1.5V AAA or R03 size batteries. Alkaline batteries recommended. Phillips/cross head screwdriver (not included) needed to insert batteries.
x2
BATTERIES INCLUDED
1.5VAA/R6 size
Replace with 2 x 1.5V AA or R6 size batteries. Alkaline batteries recommended. Phillips/cross head screwdriver (not included) needed to insert batteries.
BATTERIES INCLUDED
x3
1.5VA AA/R03 size
Replace with 3 x 1.5V AAA or R03 size batteries. Alkaline batteries recommended. Phillips/cross head screwdriver (not included) needed to insert batteries.
BATTERIES INCLUDED
Replace with 3 x
1.5V AAA or R03 size batteries. Alkaline batteries recommended. Phillips/cross head screwdriver (not included) needed to insert batteries.
1.5VA AA
x2
BATTERIES
ALKALINE
REQUIRED
1.5VA A/LR6 size
Phillips/cross head screwdriver (not included) needed to insert batteries.
NOT INCLUDED
Not suitable for children
under 3 years because of
small parts, choking hazard.
IMPORTANT: BATTERY INFORMATION
Please retain this information for future reference. Batteries should be replaced by an adult.
To install batteries:
1. Using a Phillips/cross head
TM
Bump & Go Chopper
screwdriver (not included), unscrew battery cover.
2. Insert 2 fresh 1.5 V “AA” or LR6 batteries. See diagram for polarity.
3. Replace battery cover and tighten screw.
CAUTION: TO AVOID BATTERY LEAKAGE
1. Be sure to insert the batteries correctly and always follow the toy and battery manufacturers’ instructions;
2. Do not mix old and new batteries or alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries;
3. Always remove weak or dead batteries from the product.
*
®
Class 1 LED product.
AGES
3+
CAUTION:
1. Always follow the instructions carefully. Use only batteries specified and be sure to insert item correctly by matching the + and – polarity markings.
2.
Do not mix old batteries and new batteries or standard (carbon-zinc) with alkaline batteries.
3. Remove exhausted or dead batteries from the product.
4. Remove batteries if product is not to be played with for a long time.
5. Do not short circuit the supply terminals.
6. Should this product cause, or be affected by, local electrical interference, move it away from other electrical equipment. Reset (switching off and back on again or removing and re-inserting batteries) if necessary.
7. RECHARGEABLE BATTERIES: Do not mix these with any other types of battery. Always remove from the product before recharging. Recharge batteries under adult supervision. DO NOT RECHARGE OTHER TYPES OF BATTERIES.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Consult the dealer or an experienced radio/TV technician for help.
Product and colors may vary. Spider-Man and all related characters: TM & © 2006 Marvel Characters, Inc. Spider-Man movie elements: © 2002-2006 Columbia Pictures Industries, Inc. All rights reserved. Licensed by Spider-Man Merchandising L.P. ®* and/or TM* & © 2006 Hasbro. All Rights Reserved. TM & ® denote U.S. Trademarks. Hasbro Canada, Longueuil, QC, Canada J4G 1G2
FCC STATEMENT
P/N: 6613440000
Loading...