Harris Semiconductor CA3162E, CA3162AE Datasheet

SEMICONDUCTOR

CA3162

December 1993

Features

• Dual Slope A/D Conversion

• Multiplexed BCD Display

• Ultra Stable Internal Band Gap Voltage Reference

• Capable of Reading 99mV Below Ground with Single
Supply

• Differential Input

• Internal Timing - No External Clock Required

• Choice of Low Speed (4Hz) or High Speed (96Hz)
Conversion Rate

• “Hold” Inhibits Conversion but Maintains Delay

• Overrange Indication

- “EEE” for Reading Greater than +999mV, “-” for

Reading More Negative than -99mV When Used
With CA3161E

• BCD-to-Seven-Segment Decoder/Driver

• Extended Temperature Range Version Available

A/D Converter for 3-Digit Display

Description

The CA3162E and CA3162AE are I2L monolithic A/D con­verters that provide a 3 digit multiplexed BCD output. They
are used with the CA3161E BCD-to-Seven-Segment
Decoder/Driver* and a minimum of external parts to imple­ment a complete 3 digit display. The CA3162AE is identical
to the CA3162E except for an extended operating tempera­ture range.

* The CA3161E is described in Display Drivers section of this data

book.

Ordering Information

PART

NUMBER

CA3162E 0oC to +70oC 16 Lead Plastic DIP

CA3162AE -40oC to +85oC 16 Lead Plastic DIP

TEMPERATURE

RANGE PACKAGE

Pinout

BCD

OUTPUTS

DIGIT

SELECT

OUTPUTS

ZERO ADJ

NSD

MSD

LSD

HOLD/

BYPASS

GND

1

1

2

0

2

2

3

4

5

6

7

8

CA3162 (PDIP)

TOP VIEW

3

16

2

2

15

2

14

V+

13

GAIN ADJ
INTEGRATING

12

CAP

11

HIGH INPUT

10

LOW INPUT

9

ZERO ADJ

BCD
OUTPUTS

CAUTION: These devices are sensitive to electrostatic discharge. Users should follow proper I.C. Handling Procedures.
Copyright

© Harris Corporation 1993

2-5

File Number

1080.1

Functional Block Diagram

ZERO

ADJ

8 9 12 1 2 15 16 14

HIGH INPUT

LOW INPUT

11

10

V/I

CONVERTER

CA3162, CA3162A

V+V+

INTEGRATING
CAP

CONTROL LOGIC

COUNTERS & MULTIPLEX

THRESHOLD
DET.

BCD OUTPUTS

2120222

÷2048

3

DIGIT

DRIVE

V+

3

4

5

DIGIT SELECT
OUTPUTS †

4

= MSD

5

= LSD

3

= NSD

÷96

†

MSD = MOST SIGNIFICANT DIGIT
NSD = NEXT SIGNIFICANT DIGIT
LSD = LEAST SIGNIFICANT DIGIT

REFERENCE

CURRENT

GENERATOR

BAND GAP

REFERENCE

GAIN

ADJ

OSC

HOLD/

BYPASS

GATES

CONVERSION

6

CONTROL

713

GND

2-6

Specifications CA3162, CA3162A

Absolute Maximum Ratings Thermal Information

DC Supply Voltage (Between Pins 7 & 14). . . . . . . . . . . . . . . . . +7V

Input Voltage (Pin 10 or 11 to Ground). . . . . . . . . . . . . . . . . . . . . ±15V

Storage Temperature Range . . . . . . . . . . . . . . . . . -65oC to +150oC

Lead Temperature (Soldering 10s). . . . . . . . . . . . . . . . . . . . +300oC

CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.

Thermal Resistance θ

JA

Plastic DIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . 90oC/W

Operating Temperature Range

CA3162E. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0 to +75oC

CA3162AE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40oC to +85oC

Maximum Power Dissipation

Plastic DIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.67W

Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +150oC

Electrical Specifications T

= +25oC, V+ = 5V, Zero Pot Centered, Gain Pot = 2.4kΩ Unless Otherwise Specified

A

PARAMETERS TEST CONDITIONS MIN TYP MAX UNITS

Operating Supply Voltage Range, V+ 4.5 5 5.5 V

Supply Current, I+ 100kΩ to V+ on Pins 3, 4, 5 - - 17 mA

Input Impedance, Z

Input Bias Current, I

I

IB

Pins 10 and 11 - -80 - nA

- 100 - MΩ

Unadjusted Zero Offset V11-V10 = 0V, Read Decoded Output -12 - +12 mV

Unadjusted Gain V11-V10 = 900mV, Read Decoded Output 846 - 954 mV

Linearity Notes 1 and 2 -1 - +1 Count

Conversion Rate

Slow Mode Pin 6 = Open or GND - 4 - Hz

Fast Mode Pin 6 = 5V - 96 - Hz

Conversion Control Voltage (Hold Mode)

0.8 1.2 1.6 V

at Pin 6

Common Mode Input Voltage Range, V

ICR

Notes 3, 4 -0.2 - +0.2 V

BCD Sink Current at Pins 1, 2, 15, 16 V

Digit Select Sink Current at Pins 3, 4, 5 V

≥ 0.5V, at Logic Zero State 0.4 1.6 - mA

BCD

Select = 4V at Logic Zero State 1.6 2.5 - mA

DIGIT

Zero Temperature Coefficient VI = 0V, Zero Pot Centered - 10 - µV/oV

Gain Temperature Coefficient VI = 900mV, Gain Pot = 2.4kΩ - 0.005 - %/oC

NOTES:

1. Apply zero volts across V11 to V10. Adjust zero potentiometer to give 000mV reading. Apply 900mV to input and adjust gain potentiometer
to give 900mV reading.

2. Linearity is measured as a difference from a straight line drawn through zero and positive full scale. Limits do not include ±0.5 count bit
digitizing error.

3. For applications where low input pin 10 is not operated at pin 7 potential, a return path of not more than 100kΩ resistance must be provided
for input bias currents.

4. The common mode input voltage above ground cannot exceed +0.2V if the full input signal range of 999mV is required at pin 11. That is,
pin 11 may not operate higher than 1.2V positive with respect to ground or 0.2V negative with respect to ground. If the maximum input
signal is less than 999mV, the common mode input voltage may be raised accordingly.

2-7