Rhein Tech Laboratories, Inc. Client: Harris Corporation
360 Herndon Parkway Model: XL-200P (International) Portable Radio
Suite 1400 IDs: - OWDTR-0145-E/3636B-0145
Herndon, VA 20170 Standards: FCC 22/74/80/90/IC RSS-119
http://www.rheintech.com Report #: 2015216TNF
Appendix P: Manual
Please refer to the following pages for the Operator’s Manual and the Product Safety Manual.
477 of 487
Page 2
Operator’s Manual
14221-1800-2000
Rev. D, Feb/16
XL-200P
Full-Spectrum Multiband Radio
Page 3
14221-1800-2000, Rev. D
REV.
DATE
REASON FOR CHANGE
-
Sep/15
Initial release.
A
Sep/15
Added Section 3.
B
Nov/15
Added CE information.
C
Jan/16
Updated Declaration of Conformity. Added EU regulatory approval information (standards) and
EU RF exposure information.
D
Feb/16
Updated Table 1-1 and Tableau 2-1. Updated for XLP R2A and added LTE info.
This
without any warranty. Improvements and changes to this manual necessitated by typographical errors,
inaccurac ies of cu rrent in forma tion, o r improv ements to progra ms an d/or eq uipmen t, may b e made by
at any time and without notice.
Such changes will be incorporated into new editions of this manual. No part of this manual may be reproduced or transmitted in any form or by any means,
electronic or mechanical, including photocop ying and recording, for
Harris Corporation, Public Safety and Professional Communications (PSPC) Business continually evaluates its technical publications for
completeness, technical accuracy, and organization. You can assist in this process by submitting your comments and suggestions to the
following:
Harris Corporationfax your comments to: 1-434-455-6851
PSPC Business or
Technical Publications e-mail us at: PSPC_TechPubs@harris.com
221 Jefferson Ridge Parkway
Lynchburg, VA 24501
ACKNOWLEDGEMENT
This product was developed using GEOTRANS, a product of the National Geospatial Intelligence Agency and U.S. Army Engineering
Research and Development C enter. Use of this software does not indicat e endorsement or approval of the product by the Secret ary of
Defense or the National Geospatial Intelligence Agen cy.
This device made under license under one or more of the following US patents: 4,590,473; 4,636,791; 5,148,482; 5,185,796; 5,271,017;
5,377,229; 4,71 6, 4 07; 4,972,460; 5,5 02,767; 5,146,6 97 ; 5,164,986; 5,185, 79 5.
The Advanced Multi-Band Excitation implementation 2 (AMBE+2) voice coding Technology embodied in this product is protected by
intellectual property rights including patent rights, copyrights and trade secrets of Digital Voice Systems, Inc. This voice coding
Technology is licensed solely for use within this Communications Equipment. The user of this Technology is explicitly prohibited from
attempting to extract, re move, decompile, revers e engineer, o r disassemble the Ob ject Code, or in any other way co nvert the Object Code
into a human-readable form. U.S. Patent Nos. #5,870,405, #5,826,222, #5,754,974, #5,701,390, #5,715,365, #5,649,050, #5,630,011,
#5,581,656, #5,517,511, #5,491,772, #5,247,579, #5,226,084 and #5,195,166.
CREDITS
Harris, assuredcommunications, Unity, VIDA, EDACS, NetworkFirst, and OpenSky are registered trademarks of Harris Corporation.
Bluetooth is a registered trademark of Bluetooth SIG, Inc.
Motorola is a registered trademark of Motorola, Inc.
AMBE is a registered trademark and IMBE, AMBE+, and AMBE+2 are trademarks of Digital Voice Systems, Inc.
Wi-Fi is a registered trademark of
Wi-Fi Alliance.
All brand and product names are trademarks, registered trademarks, or service marks of their respective holder s.
NOTICE!
The material contained herein is subject to U.S. export approval. No export or re-export is permitted without written approval from the U.S.
Government. Rated: EAR99; in accordance with U.S. Dept. of Commerce regulations 15CFR774, Export Administration Regulations.
Information and descriptions contained herein are the property of Harris Corporation. Such information and descriptions may not be copied
or reproduced by any means, or disseminated or distributed without the express prior written permission of Harris Corporation, PSPC
Business, 221 Jefferson Ridge Parkway, Lynchburg, VA 24501.
Repairs to this equipment should be made only by an authorized service technician or facility designated by the supplier. Any repairs,
alterations or substitutions of recommended parts made by the user to this equipment not approved by the manufacturer could void the
user's authority to operate the equipment in addition to the manufacturer's warranty.
This product conforms to the European Union WEEE Directive 2012/19/EU. Do not dispose of this product in a public
landfill. Take it to a recycling center at the end of its life.
manual is published by Harris Corporation
any purpose, without the express written permission of Harris Corporation.
2
Harris Corporation
Page 4
14221-1800-2000, Rev. D
This device is a RF transceiver intended for land mobile radio applications. The device may have use restrictions, which require that the
national authority be contacted for any system licensing requirements, frequency use, al lowable power level, etc.
3
Page 5
14221-1800-2000, Rev. D
[Czech]
dalšími příslušnými ustanoveními směrnice 1999/5/ES.
[Danish]
væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
1999/5/EG befindet.
[Estonian]
põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.
requirements and other relevant provisions of Directive 1999/5/EC.
[Spanish]
esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
[Greek]
ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.
[French]
essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE.
[Italian]
essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
[Latvian]
Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.
[Lithuanian]
1999/5/EB Direktyvos nuostatas.
[Dutch]
[Maltese]
ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC.
[Hungarian]
követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.
Česky
Dansk
Deutsch
[German]
Eesti
English
Español
Ελληνική
Harris Corporation tímto prohlašuje, že tento XL-200P je ve shodě se základními požadavky a
Undertegnede Harris Corporation erklærer herved, at følgende udstyr XL-200P overholder de
Hiermit erklärt Harris Corporation, dass sich das Gerät XL-200P
grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie
Table 10-1: Displayed Error Messages, Reasons, and Resolutions .............................................................. 95
9
Page 11
14221-1800-2000, Rev. D
The WARNING symbol calls attention to a procedure, practice, or the like, which, if
orrectly performed or adhered to, could result in personal injury. Do not
proceed beyond a WARNING symbol until the conditions identified are fully
understood or met.
The Harris XL-200P portable radio generates RF electromagnetic energy during
transmit mode. This radio is designed for and classified as “Occupational Use
urse of employment by
individuals aware of the hazards and the ways to minimize such hazards. This
radio is NOT intended for use by the “General Population” in an uncontrolled
environment.
WARNING
CAUTION
NOTE
WARNING
1. REGULATORY AND SAFETY INFORMAT ION
1.1 SAFETY CONVENTIONS
The following conventions are used throughout this manual to alert the user to general safety precautions
that must be observed during all phases of operation, service, and repair of this product. Failure to comply
with these precautions or with specific warning elsewhere in this manual violates safety standards of
design, manufacture, and intended use of the product. Harris assumes no liability for the customer’s
failure to comply with these standards.
not c
The CAUTION symbol calls attention to an operating procedure, practice, or the like,
which, if not performed correctly or adhered to, could result in damage to the equipment
or severely degrade the equipment performance.
The NOTE symbol calls attention to supplemental information, which may improve
system performance or clarify a process or procedure.
1.2 SAFETY TRAINING INFORMATION
Only,” meaning it must be used only during the co
The XL-200P portable radio has been tested and complies with the FCC RF exposure limits for
“Occupational Use Only.” In addition, this Harris radio complies with the following Standards and
Guidelines with regard to RF energy and electromagnetic energy levels and evaluation of such levels for
exposure to humans:
• FCC OET Bulletin 65 Edition 97-01 Supplement C, Evaluating Compliance with FCC Guidelines for
Human Exposure to Radio Frequency Electromagnetic Fields.
• American National Standards Institute (C95.1 – 1992), IEEE Standard for Safety Levels with Respect
to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz.
• American National Standards Institute (C95.3 – 1992), IEEE Recommended Practice for the
Measurement of Potentially Hazardous Electromagnetic Fields – RF and Microwave.
• IC Standard RSS-102. Radiofrequency Exposure Compliance of Radiocommunication Apparatus
(All Frequency Bands).
• European Council Directive 89/391/EEC.
10
Page 12
14221-1800-2000, Rev. D
CAUTION
1.2.1 RF Exposure Guidelines
To ensure that exposure to RF electromagnetic energy is within the EU/AU/FCC/IC
allowable limits for occupational use, always adhere to the following guidelines:
• DO NOT operate the radio without a proper antenna attached, as this may damage the radio and may
also cause the FCC RF exposure limits to be exceeded. A proper antenna is the antenna supplied with
this radio by Harris or an antenna specifically authorized by Harris for use with this radio. (Refer to
Table 4-1.)
• DO NOT transmit for more than 50% of total radio use time (“50% duty cycle”). Transmitting more
than 50% of the time can cause FCC RF exposure compliance requirements to be exceeded. The radio
is transmitting when the “TX” indicator appears in the display. The radio will transmit by pressing the
“PTT” (Push-To-Talk) button.
• ALWAYS transmit using low power when possible. In addition to conserving battery charge, low
power can reduce RF exposure.
• ALWAYS use Harris authorized accessories (antennas, batteries, belt clips, speaker/mics, etc). Use of
unauthorized accessories may cause the FCC Occupational/Controlled Exposure RF compliance
requirements to be exceeded. (Refer to Table 1-1.)
• As noted in Table 1-1, ALWAYS keep the housing of the transmitter AT LEAST 0.47 inches (1.2
cm) from the body and at least 0.98 in (2.5 cm) from the face when transmitting to ensure
EU/AU/FCC/IC RF exposure compliance requirements are not exceeded. However, to provide the
best sound quality to the recipients of your transmission, Harris recommends you hold the
microphone at least 2 in (5 cm) from mouth, and slightly off to one side.
Minimum safe operating distances for the radio are based on the Harmonized Standards and SAR evaluation.
2
This is worst case based on the thinnest body mount accessory (belt clip).
0.47 in (1.2 cm) 0.98 in (2.5 cm)
0.47 in (1.2 cm) 0.98 in (2.5 cm)
0.47 in (1.2 cm) 0.98 in (2.5 cm)
0.47 in (1.2 cm) 0.98 in (2.5 cm)
0.47 in (1.2 cm) 0.98 in (2.5 cm)
(worst case scenario)
11
Page 13
14221-1800-2000, Rev. D
WARNING
The information in this section provides the information needed to make the user aware of RF exposure,
and what to do to assure that this radio operates within the FCC RF exposure lim it s.
1.2.2 Electromagnetic Interference/Compatibility
During transmissions, this Harris radio generates RF energy that can possibly cause interference with
other devices or systems. To avoid such interference, turn off the radio in areas where signs are posted to
do so. DO NOT operate the transmitter in areas that are sensitive to electromagnetic radiation such as
hospitals, aircraft, and blasting sites.
1.3 REGULATORY APPROVALS
1.3.1 Part 15
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired
operation.
1.3.2 Industry Canada
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
1.4 OPERATING TIPS
Antenna location and condition are important when operating a portable radio. Operating the radio in
low-lying areas or terrain, under power lines or bridges, inside of a vehicle, or in a metal framed building
can severely reduce the range of the unit. Mountains can also reduce the range of the unit.
In areas where transmission or reception is poor, some improvement may be obtained by ensuring that the
antenna is vertical. Moving a few yards in another direction or moving to a higher elevation may also
improve communications. Vehicular operation can be aided with the use of an externally mounted
antenna.
Battery condition is another important factor in the trouble free operation of a portable radio. Always
properly charge the battery.
1.4.1 Efficient Radio Operation
Keep the antenna in a vertical position when receiving or transmitting a message.
Do NOT hold onto the antenna when the radio is powered on!
12
Page 14
14221-1800-2000, Rev. D
may result if a damaged antenna comes into contact with the skin. Replace a
damaged antenna immediately. Operating a portable radio with the antenna missing
Use only the supplied or approved antenna. Unauthorized antennas, modifications, or
RF energy from portable radios may affect some electronic equipment. Most modern
Areas with potentially explosive atmospheres are often, but not always, clearly
WARNING
CAUTION
CAUTION
WARNING
WARNING
WARNING
1.4.2 Antenna Care and Replacement
Do not use the portable radio with a damaged or missing antenna. A minor burn
could cause personal injury, damage the radio, and may violate FCC regulations.
attachments could cause damage to the radio unit and may violate FCC regulations. (Refer
to Table 4-1.)
1.4.3 Electronic Devices
electronic equipment in cars, hospitals, homes, etc. is shielded from RF energy. However,
in areas in which you are instructed to turn off two-way radio equipment, always observe
the rules. If in doubt, turn it off!
1.4.4 Aircraft
• Always turn off a portable radio before boarding any aircraft!
• Use it on the ground only with crew permission.
• DO NOT us e whi le in -flight!!
1.4.5 Electric Blasting Caps
To prevent accidental detonation of electric blasting caps, DO NOT use two-way
radios within 1000 feet of blasting operations. Always obey the "Turn Off Two-Way
Radios" signs posted where electric blasting caps are being used. (OSHA Standard:
1926.900)
1.4.6 Potentially Explosive Atmospheres
marked. These may be fuelling areas, such as gas stations, fuel or chemical transfer
or storage facilities, and areas where the air contains chemicals or particles, such as
grain, dust, or metal powders.
Sparks in such areas could cause an explosion or fire resulting in bodily injury or
even death.
Turn off two-way radios when in any area with a potentially explosive atmosphere. It
is rare, but not impossible that a radio or its accessories could generate sparks.
13
Page 15
14221-1800-2000, Rev. D
MISE EN GARDE
Le symbole MISE EN GARDE attire l’attention sur une procédure ou une
correctement effectuée ou observée, pourrait
MISE EN GARDE avant que les conditions identifiées soient complètement
AVERTISSEMENT
opérationnelle qui, si elle n’est pas correctement effectuée ou observée, pourrait
REMARQUE
MISE EN GARDE
lorsqu’en mode de transmission. Cette radio est conçue et classée pour une
ue dans le cadre d’un emploi par des individus conscients des risques et des
2. RENSEIGNEMENTS SUR LA RÉGLEMENTATION ET
SÉCURITÉ
2.1 CONVENTIONS SUR LES SYMBOLES DE SÉCURI TÉ
Les conventions suivantes sont utilisées dans le présent manuel pour avertir l’utilisateur des précautions générales de
sécurité qui doivent être observée s pendant toutes les pha ses d’opération, d’entretie n et de réparatio n de ce produit.
Le non-respect de ces précautions ou d’avertissements précisés ailleurs enfreint les normes de sécurité de la
conception, de la fabrication et de l’utilisation prévue du produit. Harris n’assume aucune responsabilité pour le
non-respect de ces normes par le client.
pratique qui, si elle n’est pas
entraîner une blessure personnelle. Ne pas poursuivre au-delà d’un symbole de
comprises ou satisfaites.
Le symbole AVERTISSEMENT attire l’attention sur une procédure ou une pratique
entraîner un bris d’équipement ou une importante baisse de rendement de l’équipement.
Le symbole REMARQUE attire l’attention sur des renseignements supplémentaires qui
peuvent améliorer le rendement du système ou clarifier un processus ou une procédure.
2.2 RENSEIGNEMENTS SUR LA FORM ATIO N S UR LA SÉCURITÉ
La radio portative Harris XL-200P produit de l’énergie électromagnétique des RF
« Utilisation professionnelle seulement », ce qui signifie qu’elle ne doit être utilisée
q
moyens de limiter ceux-ci. Cette radio N’EST PAS conçue pour une utilisation par
la « Population générale » dans un environnement non contrôlé.
La radio portative XL-200P a été testée et est conforme aux limites d’exposition aux RF de la FCC pour
une « Utilisation professionnelle seulement ». De plus, cette radio Harris est conforme aux normes et
directives suivantes quant à l’énergie des RF et aux niveaux d’énergie électromagnétique, ainsi qu’à
l’évaluation de ces niveaux pour l’exposition aux humains :
• Bulletin 65 du OET de la FCC, édition 97-01, supplément C, portant sur l’évaluation de la conformité
aux directives de la FCC quant à l’exposition humaine aux champs électromagnétiques des
radiofréquences.
• American National Standards Institute (C95.1 – 1992), norme de l’IEEE sur les niveaux sécuritaires
d’exposition humaine aux champs électromagnétiques des radiofréquences, 3 kHz à 300 GHz.
• American National Standards Institute (C95.3 – 1992), pratique recommandée par l’IEEE pour la
mesure des champs électromagnétiques potentiellement dangereux – RF et micro-ondes.
14
Page 16
14221-1800-2000, Rev. D
AVERTISSEMENT
2.2.1 Directives sur l’exposition aux RF
Pour s’assurer que l’exposition à l’énergie électromagnétique des RF se situe dans les
limites acceptables de la FCC pour l’utilisation professionnelle, respectez toujours les
directives suivantes :
• N’utilisez PAS la radio sans qu’une antenne appropriée y soit connectée, car ceci peut endommager la
radio et également causer un dépassement des limites d’exposition aux RF de la FCC. Une antenne
appropriée est celle fournie par Harris avec cette radio, ou une antenne spécifiquement autorisée par
Harris pour être utilisée avec cette radio. (Reportez-vous à Tableau 2-1.)
• Ne transmettez PAS pendant plus de 50 % de la durée d’utilisation totale de la radio (« cycle de
service de 50 % »). La transmission pendant plus de 50 % du temps peut causer un dépassement des
exigences de conformité de la FCC en matière d’exposition aux RF. La radio transmet lorsque
l’indicateur « TX » apparaît sur l’affichage. La radio transmet lorsqu’on appuie sur le bouton « PTT »
(bouton de microphone).
• Transmettez TOUJOURS en basse puissance lorsque possible. En plus de préserver la charge de la
pile, une faible puissance réduit l’exposition aux RF.
• Utilisez TOUJOURS des accessoires autorisés Harris (antennes, piles, pinces de ceinture, haut-
parleurs/micros, etc.). L’utilisation d’accessoires non autorisés peut entraîner un dépassement des
exigences de conformité pour une exposition aux RF professionnelle ou contrôlée de la FCC.
(Reportez-vous à Table 4-1.)
• Tel qu’indiqué dans Tableau 2-1, conservez TOUJOURS l’appareil et son antenne à AU MOINS
1,2 cm du corps, et à au moins 2,5 cm du visage pendant la transmission, pour vous assurer de ne pas
dépasser les exigences de conformité de la FCC en matière d’exposition aux RF. Cependant, pour
offrir la meilleure qualité sonore aux auditeurs de votre transmission, Harris recommande de tenir le
microphone à au moins 5 cm (2 po) de votre bouche et légèrement déplacé sur un côté.
Tableau 2-1 : Distances de test de conformité des expositions aux RF
Ce est le pire des cas basée sur le corps plus mince monter accessoire (clip ceinture).
15
Page 17
14221-1800-2000, Rev. D
MISE EN GARDE
Dans cette section figurent les renseignements nécessaires pour sensibiliser l’utilisateur à l’exposition aux
RF et sur ce qu’il faut faire pour s’assurer que cette radio fonctionne dans les limites d’exposition aux RF
de la FCC.
Pendant les transmissions, cette radio Harris produit de l’énergie des RF qui peut causer de l’interférence
avec d’autres appareils ou systèmes. Pour éviter de telles interférences, fermez la radio dans les zones où
il est indiqué de le faire. N’utilisez PAS le transmetteur dans des zones sensibles aux radiations
électromagnétiques, com me les hôp itaux , les av ions et les sites de détonat ion.
2.3 INTERFÉRENCE DES RADIOFRÉQUENCES
2.3.1 Partie 15 de la FCC
Cet appareil est conforme à la Partie 15 de la réglementation de la FCC. Le fonctionnement est soumis
aux deux conditions suivantes :
1. Cet appareil ne doit pas causer une interférence nuisible; et
2. Cet appareil doit accepter toute interférence reçue, y compris une interférence qui peut causer un
fonctionnement non souhaité.
2.3.2 Industrie Canada
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de
brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
2.4 CONSEILS D’UTILISATION
L’emplacement et l’état de l’antenne sont importants pour l’utilisation d’une radio portative. L’utilisation
de la radio dans des zones de faible élévation, sous des lignes électriques ou des ponts, à l’intérieur d’un
véhicule ou dans un immeuble à ossature métallique, peut réduire la portée de l’appareil de manière
considérable. Les montagnes peuvent également réduire la portée de l’unité.
Dans les zones où la transmission ou la réception est insatisfaisante, certaines améliorations peuvent être
obtenues en s’assurant que l’antenne est verticale. Se déplacer de quelques mètres dans une autre
direction ou à un emplacement plus élevé peut également améliorer les communications. L’utilisation
d’une antenne fixée à l’extérieur peut facilit er le fon c ti o nnement dans un véhicule.
L’état de la pile est un autre facteur important d’une utilisation sans tracas d’une radio portative. Chargez
toujours correctement la pile.
2.4.1 Utilisation Efficace de la Radio
Gardez l’antenne dans une position verticale pendant la réception ou la transmission d’un message.
16
Ne tenez PAS l’antenne lorsque la radio est allumée!
Page 18
14221-1800-2000, Rev. D
MISE EN GARDE
agée ou absente. Une
brûlure légère peut se produire au contact d’une antenne endommagée avec la
peau. Remplacez immédiatement une antenne endommagée. L’utilisation d’une
radio portative alors que l’antenne est absente peut causer des blessures,
AVERTISSEMENT
Utilisez seulement l’antenne fournie ou une antenne approuvée. Des antennes non
AVERTISSEMENT
L’énergie des RF provenant de radios portatives peut affecter certains appareils
jorité de l’équipement électronique moderne dans les voitures, les
MISE EN GARDE
MISE EN GARDE
2.4.1.1 Entretien Et Remplacement De L’antenne
N’utilisez pas la radio portative si son antenne est endomm
endommager la radio et pourrait enfreindre la réglementation de la FCC.
autorisées, des modifications ou des ajouts à une antenne peuvent endommager la radio et
enfreindre la réglementation de la FCC. (Reportez-vous à Table 4-1.)
2.4.1.2 Appareils Électroniques
électroniques. La ma
hôpitaux, les maisons, etc. est blindé contre l’énergie des RF. Cependant, dans les zones
où l’on vous demande de fermer l’équipement de radio bidirectionnelle, respectez toujours
les règles. En cas de doute, éteignez-le!
2.4.1.3 Avion
• Éteignez toujours une radio portative avant d’embarquer à bord d’un avion!
• Ne l’utilisez au sol qu’avec la permission de l’équipage.
• NE l’utilisez PAS durant le vol!
2.4.1.4 Détonateurs Électriques
Pour prévenir la détonation accidentelle des détonateurs électriques, n’utilisez PAS
de radios bidirectionnelles à moins de 305 m (1 000 pi) des opérations de détonation.
Respectez toujours les indications « Éteindre les radios bidirectionnelles » situées là
où des détonateurs électriques sont utilisés. (Norme OSHA : 1926.900)
17
Page 19
14221-1800-2000, Rev. D
MISE EN GARDE
en carburant, comme les postes d’essence, les installations de stockage ou de
transfert de carburant ou de produits chimiques, ainsi que les zones dont l’air
ionnelles dans toute zone ayant une atmosphère
potentiellement explosive. Il est rare, mais pas impossible qu’une radio ou ses
2.4.1.5 Atmosphère Potentiellement Explosive
Les zones ayant une atmosphère potentiellement explosive sont souvent, mais pas
toujours, identifiées clairement comme telles. Il peut s’agir de zones d’alimentation
contient des produits chimiques ou des particules, comme des grains, de la poussière
ou des poudres métalliques.
Des étincelles dans de telles zones peuvent provoquer une explosion ou un incendie,
causant ainsi des blessures ou même la mort.
Éteignez les radios bidirect
accessoires produisent des étincelles.
18
Page 20
14221-1800-2000, Rev. D
EXPLOSION HAZARD – REPLACE BATTERY PACK ONLY IN AN AREA
HAZARDOUS, AND ONLY WITH HARRIS PART NO.
LES BATTERIES DOIVENT
ARRIS PORTANT
LE NUMÉRO DE PIÈCE 14035-4010-01.
EXPLOSION HAZARD – Substitution of any component may impair suit ability for
Une substitution de toute
composante pourrait compromettre la convenance pour la Classe I, Division 2.
Do not exceed maximum battery charging current of
hen heated above 100°C (212°F) or incinerated. Replace battery with Harris Part
01 only. Use of another battery may present a risk of fire or
PART NUMBER
DESCRIPTION
12082-0600-01
SPEAKER MICROPHONE
12082-0600-02
Speaker Microphone, Emergency Button
12082-0650-01
Microphone,Palm,2 Wire, Black
12082-0650-02
Microphone,Palm,2 Wire, Beige
12082-0650-03
Microphone,Mini-Lapel,3 Wire, Black
12082-0650-04
Microphone,Mini-Lapel,3 Wire, Beige
12082-0650-05
EARPHONE KIT,BLACK,XG-100P
12082-0650-06
EARPHONE KIT,BEIGE,XG-100P
WARNING
WARNING
WARNING
WARNING
WARNING
3. HAZARDOUS LOCATIONS
(APPLIED FOR CERTIFICATION)
This equipment is suitable for use in Class I, Division 2, Groups A, B, C, and D or non-hazardous
(unclassified) locations only.
Cet équipement convient pour usage en Classe I, Division 2, Groupes A, B, C et D, ou en sites nonhasardeux (non-classifiés) seulem ent
KNOWN TO BE NON14035-4010-01.
AVERTISSEMENT – RISQUE D’EXPLOSION –
ÊTRE REMPLACÉES DANS UNE ZONE RECONNUE NON-HASARDEUSE
SEULEMENT, ET SEULEMENT AVEC UNE BATTERIE H
Class I, Division 2.
AVERTISSEMENT – RISQUE D’EXPLOSION –
EXPLOSION HAZARD –
5.250 A or maximum charging voltage of 12.0 V DC at any time.
CAUTION - The battery used in this device may present a risk of fire or explosion
w
No. 14035-4010explosion.
Battery replacement instructions: Remove battery by 1) depressi ng batt ery l atch es then 2) remove battery
from radio chassis. Install replacement battery by inserting battery in radio chassis opening and
depressing battery into chassis until both battery latches are engaged. Dispose of used battery promptly.
Keep away from children. Do not disassemble and do not dispose of in fire.
EXPLOSION HAZARD – In addition to any simple single-ended coil antenna, only
the following Harris accessori es may be used with t his rad io :
19
Page 21
14221-1800-2000, Rev. D
PART NUMBER
DESCRIPTION
12082-0650-07
Headset, In-Ear, Boom Mic, In-Line PTT
12082-0650-08
Headset, Lightweight, Over-the-Head, Single Ear, In-Line PTT
12082-0650-09
Headset, Lightweight, Behind-the-Head, Dual Ear, In-Line PTT
12082-0650-10
Headset, Lightweight, Behind-the-Head, Dual Ear, Pigtail PTT
Speaker Mic, Premium, Fire (FSM), Noise Cancelling
20
Page 22
14221-1800-2000, Rev. D
4. INTRODUCTION
4.1 DESCRIPTION
The XL-200P provides the advanced connectivity that first responders require whi le addr essing e volvin g
voice and data communications. It supports VHF, UHF, and 700/800 MHz, allowing voice and data
communications across agencies using multiple frequencies and systems. The XL-200P delivers easy-touse tools in an extremely rugged radio that operates under the most adverse conditions. The XL-200P
meets MIL-STD-810G for durability and is certified to more stringent MIL-STD parameters for
contamination by fluids and explosive atmospheres. The XL-200P is available in both Full and Partial
keypad models in black and high-visibility yellow.
Standard features found on the XL-200P include:
• Extremely Rugged – exceeds the standards of other radios on the market.
• Multiband Operation – supports any combination of VHF, UHF, and 700/800 MHz frequencies. Also
allows different bands to be enabled for selected users.
• Single-key DES Encryption – provides basic secure communications without having to buy the
complete encryption option.
• Instant Recall of Received Audio – allows user to replay the last transmission received to avoid
unnecessary repetition.
• Active Noise Cancellation – with three internal microphones to transmit intelligible audio from users
in loud environments.
• Built-in GPS – for location reporting and rapid response for emergencies.
• Integrated Bluetooth
®
• Wi-Fi
• Covert Mode – allows users to quickly configure the radio for operation in a covert environment.
• Fully Programmable Keypad – each key can be programmed to a variety of functions.
• 4 position switch – provides added configuration flexibility.
• Unique User Interface – tools specially designed by first responders make radio operation simple and
intuitive. An easy-to-read multi-color front display and a monochromatic top display with optional
colored backlighting enhance communications for improved user safety.
For optional accessories, refer to Table 4-1. Additional accessories may have been added since
publication of this manual; contact Harris for more information.
Connectivity – permits simple and easy radio software and personality updates.
®
– for wireless interface to selected accessories.
4.2 STORAGE GUIDELINES
Store your XL-200P and batteries in a clean, cool (not exceeding 86 °F [+30 °C]), dry, and ventilated
storage area.
21
Page 23
14221-1800-2000, Rev. D
WARNING
CAUTION
4.3 BASIC SETUP
4.3.1 Assemble the Radio
Only use a Harris charger approved for the battery chemistry. Injury cou ld occu r
from improper charger use.
Do not over-tighten the antenna as damage could result.
1. Make sure batteries are charged per the manual supplied with the charger.
2. To attach optional belt clip, remove the existing tab from the back of the radio above the battery
compartment. Slide the belt clip into the groove.
3. Lift clip, if installed, and slide top of battery into top of battery compartment at the rear of the radio.
4. Press down on bottom side of battery until it snaps into place.
22
Figure 4-1: Radio Assembly
Page 24
14221-1800-2000, Rev. D
4.3.2 Removing the Battery
To remove, press and hold the two tabs at the bottom of the battery and then pul l ba t t e r y u p and out of the
radio.
Figure 4-2: Remove the Battery
4.3.3 Removing the Optional Belt Clip
Remove the battery before removing the belt clip. To remove the belt clip, press and hold the tab towards
the top of the battery compartment and slide the belt clip out of the groove in the back of the radio.
Figure 4-3: Remove Belt Clip
23
Page 25
14221-1800-2000, Rev. D
4.4 UNIVERSAL DEVICE CONNECTOR
The Universal Device Connector (UDC) provides connections for external accessories such as a headset,
a speaker-microphone, audio test box, audio test cables, and programming cables. The UDC is located on
the right side of the radio, opposite the PTT Button. The UDC facilitates programming and testing the
radio. The UDC pins perform different functions depending on the accessory attached to the UDC.
4.5 CLEANING
Keep the exterior of the radio, battery, antenna, and radio accessories clean.
Periodically clean using the following procedures:
1. To remove dust and dirt, clean using damp clean cloth (warm water and mild detergent soap).
2. Follow by wiping with damp (warm water) clean cloth. Wipe dry with clean cloth.
3. Remove the battery and wipe the battery and radio contacts using a soft dry cloth to remove dirt or
grease. This will ensure efficient power transfer from the battery to the radio.
4. Remove any accessories and clean the UDC contacts using a clean dry cloth. When the UDC is not
in use, cover the connector with the protective dust cap to prevent the build-up of dust or water
particles.
5. If the radio is used in a harsh environment (such as driving rain, salt fog, etc.), it may be necessary to
periodically dry and clean the battery and radio contacts with a soft dry cloth or soft-bristle nonmetallic brush.
Figure 4-4: Universal Device Connector
24
Page 26
14221-1800-2000, Rev. D
CAUTION
NOTE
For more rigorous cleaning, use the following procedure:
Do not use chemical cleaners, spray, or petroleum-based products. They may damage
the radio housing. We recommend using Chemtronics® Electro-Wash® PR (ES-1603) or
equivalent.
1. Apply the cleaning solution to a clean damp cloth and clean the radio.
Do not spray cleaning solution directly on radio. To clean the radio in the speaker and
microphone areas, carefully wipe these areas but prevent the cleaning solution from
entering the speaker or microphone openings.
2. Wipe off the radio with clean damp cloth using mild warm soapy water.
3. Follow up by wiping off the radio with clean damp cloth using warm water only.
Speaker Microphone, Premium, Fire, Noise Cancelling,
High Visibility Yellow
Microphone, Palm, 2-Wire, Black
12082-0650-01
XL-AE6G
Microphone, Palm, 2-Wire, Beige
12082-0650-02
XL-AE6M
Microphone, Mini-Lapel, 3-Wire, Black
12082-0650-03
XL-AE6H
Microphone, Mini-Lapel, 3-Wire, Beige
12082-0650-04
XL-AE6N
Earphone Kit, Black
12082-0650-05
Earphone Kit, Beige
12082-0650-06
Headset, In-Ear, Boom Mic, In-Line PTT
12082-0650-07
XL-AE2A
Headset, Light Weight, Over-the-Head, Single Ear, InLine PTT
Headset, Light Weight, Behind-the-Head, Dual Ear, InLine PTT
Headset, Light Weight, Behind-the-Head, Dual Ear, Pig
Tail PTT
Headset, Light Weight, Behind-the-Head, Dual In-Ear,
In-Line PTT
Headset, Light Weight, Behind-the-Head, Dual In-Ear,
Pig Tail PTT
Headset, Heavy Duty, Behind-the-Head, w/PTT
12082-0650-13
XL-AE1P
Headset, Heavy Duty, Over-the-Head, w/PTT
12082-0650-14
XL-AE1R
Headset, BTH Boom Mic, Earpiece, w/PTT
12082-0650-15
XL-AE2G
Headset, Tactical, Boom Mic, Earpiece, w/PTT
12082-0650-16
XL-AE1H
Skull Mic, w/Body PTT, Earcup
12082-0650-17
XL-AE1L
Throat Mic, w/Acoustic Tube, Body PTT
12082-0650-18
XL-AE1M
Throat Mic, w/Acoustic Tube, body and Ring PTT
12082-0650-19
XL-AE1N
Bluetooth, Covert, Earpiece/MIC/PTT, Radios
12082-0684-01
XL-AE1S
MISCELLANEOUS ACCESSORIES
Cable, Data Interface
12082-0445-A1
XL-CJ4A
Cable, MATQ-03424, Test
12082-0435-A1
CAUTION
4.6 OPTIONS AND ACCESSORIES
Only use Harris approved accessories. Refer to Harris’ Product and Services catalog for the complete list
of options and accessories available. Contact Harris for requirements not contained in this list:
Always use the correct options and accessories (battery, antenna, speaker/mic, etc.) for
the radio. Immersion rated options must be used with an immersion rated radio. Refer to
Table 4-1.
Table 4-1: Options and Accessories
12150-1000-05
12082-0650-08 XL-AE2B
12082-0650-09 XL-AE2C
12082-0650-10 XL-AE2D
12082-0650-11 XL-AE2E
12082-0650-12 XL-AE2F
26
Page 28
14221-1800-2000, Rev. D
DESCRIPTION
PART NUMBER
OPTION NUMBER
Cable, USB, Key Loading/Programming
12082-0410-A1
XL-CJ3A
Cable, KVL, Key Loading
12082-0400-A1
XL-CJ3B
Adapter, 6-Pin Hirose
14002-0197-01
XL-CJ4B
Holster, Leather, Radio, Premium
14035-4201-01
XL-HC4K
Belt Loop, Leather, Premium
14002-0218-01
XL-HC4A
D-Swivel
12082-3230-01
Strap, Shoulder
CC103333V1
Metal Belt Clip
12082-1290-01
XL-HC3L
Case, Leather, Premium, Shoulder Strap
14035-4201-02
XL-HC4L
27
Page 29
14221-1800-2000, Rev. D
CONTROL/INDICATOR
FUNCTION
Group/Channel Knob
Selects groups/channels.
Turn clockwise to power on radio and increase volume of audio heard from
missed calls due to a low volume setting.
A/B (Ø/O) Switch
User-programmable switch (see Section 7.4.2).
NOTE
5. BASIC OPERATION
5.1 XL-200P CONTROLS
Figure 5-1: XL-200P Controls
Table 5-1 describes the default functions of buttons, knobs, and controls. Most can be
programmed for different functions; see Section 7.4 for more information.
Table 5-1: XL-200P Controls, Indicators, and Connectors
Power/Volume Knob
28
speaker. Minimum volume levels may be programmed into the radio to prevent
Page 30
14221-1800-2000, Rev. D
CONTROL/INDICATOR
FUNCTION
When noise cancellation is enabled, the secondary and primary microphones are
for detailed information on using noise
cancellation.
User-programmable switch (see Section 7.4.3). By default, selects one of four
channel banks (see Section 5.17).
Used to select a commonly used function as an alternative to navigating menus.
See Section 7.4.1 for the options that can be programmed to these buttons.
Push-To-Talk (PTT)
Button
Battery
Battery - Refer to Section 4.3 for battery connection and removal.
Antenna Connector
Antenna connector.
Used to place radio in emergency mode (see Section 5.31). This button can be
to do so.
Indicates radio status:
•Orange = actively transmitting encrypted.
Shows summary of radio operation, including channel/talkgroup (which can be
be configured for viewing from the front or rear of the radio. (Section 6.6).
Radio speaker which can be muted (Section 6.5). Adjust volume using the
Power/Volume knob.
When noise cancellation is enabled, the primary and secondary microphones are
cancellation.
Front Display
Front display shows complete status and radio menus.
User-programmable dynamic keys that have their current function labeled on the
can be programmed to these buttons.
From the Main Display, press this button to access the menu. Also selects
highlighted menu items.
Microphone
(Secondary)
A/B/C/D Switch
User-Programmable
Buttons
Emergency Button
Indicator Light Emitting
Diode (LED)
used together to form a dual microphone system. Noise cancellation improves the
quality of transmitted voice. When noise cancellation is disabled, only the primary
microphone is used. See Section
This is configured via programming using Radio Personality Manager 2 (RPM2).
Press to transmit. Make sure Push-To-Talk (PTT) is enabled (Section 6.5).
disabled via programming using RPM2. In addition, this button can be used in
conjunction with a User Programmable Button to Clear Emergencies if configured
• Red = actively transmitting.
• Green = actively receiving.
5.7
Top Display
Speaker
Microphones (Primary)
User-Programmable
Soft Keys
Menu/Select Button
color coded), as well as a variety of programmable icons. Display orientation can
used together to form a dual microphone system. Noise cancellation improves the
quality of transmitted voice. When noise cancellation is disabled, only the primary
microphones are used. See Section
radio display directly above each button. See Section 7.4.1 for the options that
5.7 for detailed information on using noise
29
Page 31
14221-1800-2000, Rev. D
CONTROL/INDICATOR
FUNCTION
Navigates menu items.
display to display the functions assigned to
Press to end or reject an ICALL.
By default, used to enter text or numbers. Can be programmed for various
00P supports a “soft”
NOTE
In addition:
Press while on the idle display to access Channel Information (see Section
Navigation Buttons
6.4).
Press while on the idle
programmable buttons (see Section 7.4).
Press to display Missed Call info.
functions (see Section 7.4).
Keypad
5.2 SOFT DTMF KEYPAD
The partial keypad model of the XL-200P supports a “soft” DTMF keypad. This allows the radio user to
utilize a graphical DTMF keypad in place of a physical DTMF keypad.
On screens that require keypad entry, press the KEYPAD softkey to display the keypad. Use , , ,
and to navigate, press the Menu/Select button to select highl ighted di git, and then press the ENTER
softkey.
For example, when placing an Individual Call to a numeric address, the soft DTMF keypad can be used to
enter the address as shown:
The partial keypad model of the XL-2
DTMF keypad. This allows the radio user to utilize a graphical
DTMF keypad in place of a physical DTMF keypad.
Figure 5-2: Using the Soft DTMF Keypad
5.3 BEFORE FIRST USE
Make sure XL-200P has:
• Fully charged battery
• Antenna attached
30
• Personality and radio programmed using RPM2
• Encryption keys loaded if using encrypted channels
• Personality activated
Page 32
14221-1800-2000, Rev. D
The radio can be programmed to require the entry of a PIN in order to operate the radio.
NOTE
NOTE
5.4 POWER ON AND SET VOLUME
The power switch and volume control are the same knob on top of the radio (see Figure 5-1). Turn the
Power/Volume Knob clockwise to power on XL-200P and increase the volume.
A minimum volume level can be programmed into the radio to prevent missed calls due
to a low volume setting.
Check with your System Administrator if you forget your PIN. As the PIN is entered, an
asterisk is displayed for each digit; the actual value is not displayed.
5.5 RADIO DISPLAYS
5.5.1 Top Display
The top display (Figure 5-3) shows a summary of status, such as channel number/bank, channel short
name, battery, scanning, and emergency mode. The display can be configured for viewing from the front
or rear of the radio (see Section 6.6). The channel short name is programmed in RPM2.
Figure 5-3: Top Display
5.5.2 Front Display
Figure 5-4 shows a sample front display while on the idle screen. The idle screen appears after power up
or after exiting from the menus.
Figure 5-4: Sample Idle Front Display
31
Page 33
14221-1800-2000, Rev. D
ICON
DESCRIPTION
ICON
DESCRIPTION
ICON
DESCRIPTION
(Blue)
Trunked Signal Strength
(Red)
TX Power
(Blue)
Bluetooth Connected
(Green)
Receive Signal Strength
(No Color)
Channel Idle
(Orange)
Transmitting Encrypted
Battery Level
100% Capacity
Battery Level
75% Capacity
Battery Level
50% Capacity
Battery Level
(Low Battery Audio Indicator)
Battery Level
(RX-Only State)
Conventional Site
Registered
Table 5-2 describes some of the icons that may be displayed by the XL-200P. The radio menu also
contains an icon glossary in the Utility Menu (see Section 5.7). Icons and their location can be
customized using RPM2.
Table 5-2: Radio Icons
Battery Fully Charged
Battery Level
25% Capacity
Bluetooth Enabled
Encryption Enabled
Global Encryption
OTAR Disabled
OTAR Registered
OTAR Registering
OTAR Rekeying
Transmit Power Level High
Transmit Power Level Low
Monitor On
VDOC
Receiving Data
Transmitting Data
Alert(s) Present
Vote Scanning
Scanning Enabled
Emergency
RX Mail
Noise Cancellation Enabled
Fire Speaker Mic Attached
Battery Exhausted
Talkaround Enabled
32
5% Capacity
Battery Charging
Failsoft
RX Only
Speaker Muted
TX Disabled
Tones Disabled
PTT Disabled
Nuisance Channel
Conventional Site
Unregistered
Type 99 Enabled
GPS Tracking
Page 34
14221-1800-2000, Rev. D
MESSAGE
DESCRIPTION
TOP-LEVEL
MENUS
5.6 STATUS MESSAGES
The radio may display various radio Status Messages during operation. These messages are described in
Table 5-3.
Table 5-3: Status Messages
PTT DENIED
CALL QUEUED P25 Trunked only - The system has placed the call in a request queue.
SYSTEM BUSY
SCANNING The radio is scanning.
TX EMERGENCY An emergency call is being transmitted.
RX EMERGENCY An emergency call is being received. The radio displays the unit name or unit ID.
WIDE AREA SCAN
INVALID TALKGROUP
INVALID UNIT P25 Trunked only - The current unit is not valid for the current system.
REGISTERING
CTRL CHANNEL SCAN
BAND SCANNING
MISSED CALL
OTAR REKEY
COMPLETE
P25 Trunked only - The radio or talkgroup is not authorized to operate on the selected
system and/or talkgroup.
P25 Trunked only - The system is busy, no channels are currently available, the queue is
full, or an individual call is being attempted to a radio that is currently transmitting.
P25 Trunked only - The radio has entered the Wide Area Scan mode to search for a new
system.
P25 Trunked only - The current talkgroup is not valid for the current system. This could
happen if the site denies registration due to an unrecognized talkgroup ID.
P25 Trunked only - Displayed when the radio is performing a registration/affiliation on a
P25 trunking site.
P25 Trunked only - The control channel is lost and the radio has entered the Control
Channel Scan mode to search for the control channel (usually out of range indication).
P25 Trunked only - Only displayed if the P25T system is configured for "EnhancedCC"
mode of operation. When the radio cannot find a Control Channel in either the trunked
frequency set or the list of discovered adjacencies, the radio is able to perform a full
spectrum frequency scan to find a new Control Channel.
P25 Modes Only – Another user has tried to call or page this radio. The user can view
who the caller was by pressing the
OTAR Rekey operation completed successfully.
key.
5.7 MENU
Press the Menu/Select button while on the idle display to access the menu. Press the or buttons to
navigate the top-level menus, and press the or buttons to navigate the sub-menus. Refer to Figure
5-1 for button location. While in a menu, press the Menu/Select button to choose, activate, or toggle the
selected item; similar to an enter key. Table 5-4 provides a high-level overview of the menu layout.
Menu options on your radio may vary depending on available features and radio programming.
EXIT EMERGENCY Exits emergency. See Section 5.31 for more information.
TALKAROUND MODE Enable/disable talk-around. See Section 5.22 for more information.
CALL
TYPE 99 TOGGLE Enable/disable T99. See Section 5.23 for more information.
TONE ENCODE
Table 5-4: Menu Navigation
SUB-MENUS DESCRIPTION
Analog conventional only - Transmits a programmed tone sequence on the current radio
system and channel. See Section 6.19 for more information.
33
Page 35
14221-1800-2000, Rev. D
TOP-LEVEL
MENUS
SUB-MENUS DESCRIPTION
CALL
(Continued)
SCAN
SECURITY
MESSAGES
UTILITY
INDIVIDUAL CALL
CHANGE TLKGRP Change the selected talkgroup. See Section 5.13.
CALL ALERT Select a group for Call Alert transmission. See Section 5.24.
CHANNEL GUARD Select the Transmit and/or Receive Channel Guard tone. See Section 5.21.
AUDIO PLAYBACK Replays the last recorded call. See Section 5.26 for more information.
START SCAN/STOP SCAN Start or stop scan operation. See Sections 5.27 and 5.28.
SCAN LISTS View/Edit available scan lists. See Section 6.14.
ASSIGNED CUSTOM LIST Create, View, and Edit Custom Scan Lists. See Section 6.14.6.
SITE ROAMING Enable/Disable Wide Area System Scan. See Section 6.14.7.
ZEROIZE KEYS Removes all encryption keys from the radio. See Section 6.20.2.
GLOBAL ENCRYPTION Enable/Disable Global Encryption. See Section 6.20.4.
GLOBAL KEY
ACTIVE KEYSET Select the Active Keyset. See Section 6.20.5.
KEYLIST
OTAR Enable/disable Over-the-Air Rekeying (OTAR). See Section 6.20.7.
OTAR REKEY Request that the KMF updates the keys in the radio. See Section 6.20.7.
RADIO STATUS
RADIO MESSAGE
TEXTLINK MESSAGES Allows the user to send a Radio TextLink message. See Section 6.17.
TEXTLINK FORMS Allows the user to send a Radio TextLink form. See Section 6.17.
TEXTLINK MAILBOX
FAULTS/ALERTS Displays radio faults and alerts. See Section 6.18.
AUDIO SETTINGS:
• SPEAKER (MUTE/UNMUTE) Mute or unmute the speaker audio.
• NOISE CANCELLATION Enable or disable Noise Cancellation. See Section 5.16.
• PTT
• TONES Enable or disable radio side tones.
• KEYPAD TONES Enable or disable tones that sound when the radio’s keypad buttons are pressed.
DISPLAY SETTINGS:
• COLOR SCHEME
• FRONT BACKLIGHT
• FRONT BRIGHTNESS Press or to dim or brighten the display.
• FRONT TIMEOUT
• TOP BACKLIGHT
• TOP BRIGHTNESS Press or to dim or brighten the display.
• TOP TIMEOUT
Allows you to select an individual for an individual call. See Section 5.14 for more
information.
Select the Global Key. Only available if Global Encryption is Enabled. See Section
6.20.4.
View available key lists. See Section 6.20.6
Used to send a particular status condition to the site without making a voice call. See
Section 6.15.
Used to send a particular message to the site without making a voice call. See Section
6.16.
Contains received Radio TextLink messages. See Section 6.17
Enable or disable Push-To-Talk (PTT). Disable PTT to prevent accidental keying, such as
when radio is in the holster or you are getting into a car.
Press the Menu/Select button to toggle the front and top display’s COLOR SCHEME for
optimum visibility in day or night conditions (NORMAL or INVERTED).
Press the Menu/Select button to toggle the front display backlighting between
ON/OFF/MOMENTARY.
When the FRONT BACKLIGHT setting is MOMENTARY, this value specifies how long
the radio needs to be inactive before the front display’s backlight turns off. Press or
to change the time in 0.5 second increments.
Press the Menu/Select button to toggle the top display backlighting
ON/OFF/MOMENTARY.
When the TOP BACKLIGHT setting is MOMENTARY, this value specifies how long the
radio needs to be inactive before the top display’s backlight turns off. Press or to
change the time in 0.5 second increments.
.
.
34
Page 36
TOP-LEVEL
MENUS
UTILITY
(Continued)
ZONE
14221-1800-2000, Rev. D
SUB-MENUS DESCRIPTION
DISPLAY SETTINGS (Cont.)
• TOP ORIENTATION
• INDICATOR LED Press the Menu/Select button to toggle the indicator LED ON or OFF.
BLUETOOTH:
• ENABLED (YES/NO) Enable/disable Bluetooth. See Section 6.10 for more information.
• PAIRING MGMT Pair Bluetooth devices with the radio. See Section 6.10 for more information.
CLOCK SETTINGS:
• TIME FORMAT Select 12 or 24 hour time display format.
• TIME ZONE Set time zone relative to Universal Time Coordinated (UTC).
GPS SETTINGS:
• GPS (ENABLED/DISABLED) Enable/disable GPS.
• POSITION INFO Displays GPS, Latitude, Longitude, and Altitude information. From this menu, click NEXT
• ANGULAR UNITS Set unit of measurement of displayed angular units: CARDINAL, DEGREES, or MILS.
• LINEAR UNITS Set unit of measurement of displayed linear units: STATUTE, METRIC, or NAUTICAL.
• POSITION FORMAT
PROGRAM:
• ACTIVATE PLAN View/Activate a personality. See Section 6.1.
• ACTIVATE PROFILE Change current profile. See Section 5.15.
MAINTENANCE
• BATTERY INFO
• RADIO INFO Displays radio information, i.e., ESN, software revisions, and firmware revisions.
• TESTS Allows service personnel to run radio tests.
• PH2 LC DISPLAY For field service use only.
• DISPLAY RSSI
• TCXO TUNING
• FEATURE INFO Displays what features are enabled on your radio.
ICON GLOSSARY Defines icons that may be displayed by the radio.
CHANGE LANGUAGE Press the Menu/Select button to toggle between available languages.
CHANGE PIN Allows you to change your PIN.
View or change zones/systems (see Sections 5.10 and 6.3.1).
Set orientation of top display to be viewed from radio: FRONT, BACK, or AUTO. When
AUTO is selected, the radio changes the top display to be viewed from the back if an
external microphone or speaker is attached. Otherwise, the display can be viewed from
the front.
to access SA INFO (see Section 6.2).
Set format of displayed position information: Latitude/Longitude Degrees Minutes
Seconds (LAT/LONG DMS), LAT/LONG DM, Military Grid Reference System (MGRS), or
Universal Transverse Mercator (UTM).
When a smart battery is attached, displays detailed battery status information. When a
regular battery is attached, displays battery voltage.
When enabled, RSSI is displayed on the RSSI screen and in the bottom of the idle
display. -130 dBm is displayed when there is no received signal.
For field service personnel only. Improper adjustment will result in loss of
communications.
35
Page 37
14221-1800-2000, Rev. D
MENU
FULL
LIMITED
RESTRICTED
Call Menu
Exit Emergency
Talkaround
Individual Call
Change Talkgroup
Call Alert/Page
Channel Guard
Audio Playback
Tone Encode
T99
Audio Settings
Display Settings
GPS Settings
Clock Settings
Bluetooth Settings
Scan Menu
Enable/Disable Scan
View Scan List
Edit Zone Scan List
View Custom Channels
Edit Custom Scan List
Custom Scan
Site Roam
Security Menu
Encryption Enable
Zeroize
Global CKR Enable
GCKR Key Select
Active Key Set
Key List
OTAR Enable
OTAR Rekey
5.8 PREDEFINED MENU LAYOUTS
Depending on radio programming, some menu options described in this manual may not be available.
The XL-200P supports three predefined menu layouts: Full, Limited, and Restricted. Table 5-5 details
what is available in each layout:
Table 5-5: Predefined Menu Layouts
36
Page 38
14221-1800-2000, Rev. D
MENU
FULL
LIMITED
RESTRICTED
Message Menu
Radio Status
Radio Message
Textlink Messages
Textlink Forms
Textlink Mailbox
Faults
Program Menu
Activate Plan
Activate Profile
Maintenance Menu
Radio Info
Battery
TCXO Tuning
P25 Tests
RSSI Display
Phase II Display
Feature Info
Change Language
Change PIN
Icon Glossary
Zone
TONE
DESCRIPTION
SOUND/DURATION
• Trunking Channel unavailable
5.9 ALERT TONES
The XL-200P pr ovides audible Alert Tones or “beeps” to indicate various operating conditions. Some of
the most common tones are described in Table 5-6.
Ready To Talk Tone
Unencrypted (Analog FM or
P25 digital)
Ready to Talk Tone
Encrypted P25 digital
PTT Denied
After a PTT is pressed, this is an audible indication (tone) for
you to begin speaking into the microphone.
After a PTT is pressed, this is an audible indication (tone) for
you to begin speaking into the microphone.
PTT not possible. Momentary tone is present:
• Receive only
• Key not found
• PTT button disabled
• Emergency button disabled
• Emergency not supported for current channel
• Clear transmit denied
Table 5-6: Alert Tones
1000 Hz tone for 25 ms
1200 Hz tone for 25 ms
544 Hz tone for 75 ms
37
Page 39
14221-1800-2000, Rev. D
may be held to scroll repetitively, and the menu will wrap to allow quick
Select the desired zone/system using the Menu/Select button.
TONE DESCRIPTION SOUND/DURATION
Maximum transmit duration
expires
Low Battery Alarm
Emergency Call Received Radio is receiving an emergency call or priority call.
Out of Range Radio fails to find a local control channel.
Maximum transmit duration is exceeded.
Alarm sounds upon initial detection of low battery and every
30 seconds thereafter. Tone stops upon detection of a battery
charging state.
5.10 SELECT ZONE/SYSTEM
A System is a group of channels or talkgroups that share a common set of parameters as programmed in
RPM2. For example, a Trunking system defines the parameters needed to communicate on a particular
infrastructure by agency or geographical region, such as WACN, System ID, Talkgroups, etc. A
conventional system defines the channel set used and any specific signaling attributes (See RPM2 for
more information on System attributes). Systems are designated by the XX icon in the Zone/System
menu.
5 beeps of 2400 Hz tone and
then a 544 Hz tone for as long
as PTT is pressed
Sequence of tones:
• 937 Hz tone for 50 ms
• Silence for 60 ms
• 1300 Hz tone for 50 ms
600 Hz tone for 250 ms and
1800 Hz tone for 250 ms
Programmable via RPM2:
• Disabled (no tone)
• Slow (tone every 15s)
• Medium (tone every 10s)
• Fast (tone every 5s)
• Tones is 544 Hz tone for 75
ms
A Zone is an OPTIONAL container that can hold channels or talkgroups from a variety of systems (see
Section 6.3.2). In other words, each member of a Zone belongs to an underlying system. (See RPM2 for
more information on Zone attributes). Zones are always listed first in the Zone/System menu and are
designated by the icon. A button on the radio can be programmed to scroll through available
zones/systems (see Section 7.4).
Or
Select a zone/system via the menu:
1. Press the Menu/Select button to access the menus.
2. Use
or to display the ZONE menu. The currently selected zone/system
will be highligh ted. A personality can have up to 512 systems and up to 50
Zones, independent of banks or channels.
3. Use or to highlight the desired zone/system. The and buttons
access to a particular zone/system
4. Press the VIEW ZONE soft key to view channels in the zone/system, or
38
Page 40
14221-1800-2000, Rev. D
arious options that can be programmed to the radio buttons
NOTE
5.11 SELECT GROUP/CHANNEL AND BANK
The XL-200P can be programmed with 1,250 talkgroups or 1000 channels per personality. Use the
Group/Channel knob to select groups/channels 1 - 16. Use the A/B/C/D switch to set the bank. The
selected bank is indicated on the display.
• Bank A: Channel A1 - A16 (1-16)
• Bank B: Channel B1 - B16 (17-32)
• Bank C: Channel C1 - C16 (33-48)
• Bank D: Channel D1 - D16 (49-64)
If your system has more than 64 groups/channels, a button on the radio can be programmed for the SEL
CHAN/GRP option. This allows you to select a “super bank,” providing access to groups/channels
beyond the first 64.
Note that ZONES have a limit of 64 entries per zone and cannot be “superbanked.”
5.12 LOCK/UNLOCK KEYPAD
There ar e two levels of keypad lock available. Keypad lock and Radio lock. Keypad lock only locks the
navigation keys (except for use in unlock), programmable softkeys, and DTMF keypad. Radio lock
disables all physical keys and knobs except
• The 4-position switch
• PTT
• Emergency Button
• Any User Programmable Button (UPB) programmed for Monitor/Clear (This is required to allow
Monitor/Clear to function for 2-button emergency clear)
The A/B switch , ABCD switch, or a button on the radio can be programmed to lock the keypad/radio. If
the keypad was locked via a switch, moving the switch to another position will unlock the keypad. If
locked via a button, the navi gation keys must be used to enter the unlock sequence of Left, Righ t, Up
Down.
See Section 7.4 for the v
and switches.
39
Page 41
14221-1800-2000, Rev. D
the talkgroup for the selected channel may be
ress the Menu/Select button to access the main
menu.
and press the
After selecting the new talkgroup, the radio returns to
5.13 GROUP CALLS
5.13.1 Transmit a Group Call
A talkgroup is a group of radios that you want to have private conversations with. These groups can be
divided into areas such as state, region, county, or large special events. A group call can only be made on
digital channels.
Turn the Channel/Group knob to select the desired group (see Figure 5-1). Press PTT to transmit.
Or
A button on the radio can be programmed for DIRECT CHANNEL ENT RY to allow the user to enter the
talkgroup/channel number. Press PTT to transmit.
Or
1. In P25 Conventional,
overridden as follows: P
2. Press or to display the CALL menu.
3. Press or to highlight CHANGE TLKGRP and press the Menu/Select
button.
4. Press or to highlight and the desired talkgroup
Menu/Select button.
the main screen.
5. Press PTT to transmit.
5.13.2 Receive a Group Call
When receiving a group call, the status area of the idle displ ay to ggles b etwe en
the Unit Name and the Group Name of the transmitting radio. Note that if either
of those names is not programmed the corresponding ID number is displayed.
40
Page 42
14221-1800-2000, Rev. D
1. Press Menu/Select button to access the main menu.
to highlight the unit to call and press the Menu/Select button,
When transmitting an Individual Call, the radio
displays the called radio’s name or Unit ID. If the radio is programmed for
Acknowledged Individual Call, the radio displays “CALL QUEUED” until
How long the radio remains in Individual Call mode with no activity is programmable.
s the calling radio’s
), change
5.14 INDIVIDUAL CALLS
An individual call is used to make a call to one radio as opposed to a group of radios. An individual call
can only be made on a digital channel.
5.14.1 Transmit an Individual Call
2. Press or to display the CALL menu.
3. Press or to highlight INDIVIDUAL CALL and press the Menu/Select
button.
4. Use or
or select KEYPAD to enter the Unit ID.
5. Press PTT to make the call.
the callee answers or rejects the call.
6. After the callee answers, press PTT to respond.
7. Press to end the call.
5.14.2 Receiving an Individual Call
1. When receiving an Individual Call, the radio display
name or Unit ID. The radio will also display “Press to END.”
2. Press PTT to respond or to END/REJECT the call. How long the radio
remains in the Individual Call mode with no activity is programmable.
3. The radio rings and indicates a missed call if you do not respond. The ring
sounds until you press PTT, view the missed call menu (
channel/group/system, or power cycle the radio.
4. On the missed call screen, press the DISMISS soft key to clear the entry.
41
Page 43
14221-1800-2000, Rev. D
1. Press the Menu/Select button to access the menu.
5. Press or to select the desired Profile (COVERT or NONE) and press the Menu/Select button.
NOTE
5.15 PROFILES
The XL-200P supports a Covert profile. The following attributes apply when the Cov ert profile is activ e:
• The speaker is enabled.
• All tones are disabled.
• Keypad tones are disabled.
• Voice Annunciation is disabled.
• The front display backlight is disabled
• The top backlight is turned off.
• The indicator LED is disabled.
• All other attributes remain at their current value.
To change the currently selected Profile:
2. Press or until the UTILITY menu is displayed.
3. Press or to highlight PROGRAM and press the Menu/Select button.
4. Press or until the PROFILES menu is displayed.
A profile change persists across system/channel changes, power cycles, and personality changes.
A button on the radio keypad can be used to toggle profiles. See Section 7.4.1.
5.16 NOISE CANCELLATION
The XL-200P features Harris’ proprietary noise suppression capability to pr ovide clear and crisp voice
quality in high-noise environments. This can be used in any mode, including analog and digital
communications.
The XL-200P has three microphones; two located at the top of the radio (primary) and one on the bottom
(secondary). W hen noise cancellation is enabled, voice is picked up by the upper left microphone, and
noise is picked up from the bottom microphone.
In the case where noise cancellation is enabled and a speaker microphone is attached to the XL-200P, talk
into the speaker microphone. In this mode, XL-200P top left microphone is used to pick up the
surrounding noise, and the other microphones are unused. See Section 5.16.4 for more information. If the
bottom (secondary) microphone is blocked, the XL-200P operates as though noise cancellation is turned
off.
42
Page 44
14221-1800-2000, Rev. D
1. Press the Menu/Select button to access the menu.
and press the
Toggle Noise
5.16.1 Enable Noise Cancellation
To enable Noise Cancellation:
2. Press or until the UTILITY menu is displayed.
3. Press or to highlight AUDIO SETTINGS
Menu/Select button.
4. Press or to highlight NOISE CANCELLATION.
Cancellation ENABLED/DISABLED using the Menu/Select button.
Refer to Section 6.5 for more information on the Audio Settings menu.
5.16.2 Using Noise Cancellation
When using the noise cancellation feature, observe the following:
• Verify NOISE CANCELLATION is enabled (see Section 5.16.1).
• Ensure the primary and secondary microphones are not covered. See Section 5.16.4 for more
information on the primary and secondary microphones.
• Talk within two (2) inches of the primary microphones (see Figure 5-5).
• Speak clearly, loudly, and with authority.
• If possible, face the noise source when talking into the radio (see Figure 5-5).
• In very noisy environments, it is o.k. to yell into the radio. The radio can handle loud input levels.
Figure 5-5: Using Noise Cancellation
5.16.3 The Effect of Distance from the Microphone
Unlike a normal microphone system, noise cancellation makes the level of your voice diminish quickly as
you move away from the radio. In essence, the radio starts to see your voice as surrounding noise.
Whereas, you may be comfortable speaking up to a foot away under normal operation, noise cancellation
requires that you hold the radio close.
43
Page 45
14221-1800-2000, Rev. D
NOTE
5.16.4 Primary versus Secondary Microphone
5.16.4.1 Without a Speaker Microphone Attached
The primary microphones are located on top of the radio and the secondary is on the bottom of the radio
(refer to Figure 5-1 for microphone locations).
5.16.4.2 With a Speaker Microphone Attached
When a speaker microphone is attached, the radio electronically switches over to use the radio’s top left
microphone as secondary. The microphone on the attached speaker microphone becomes primary.
5.16.5 When using an SCBA Mask
When using an SCBA mask, the primary microphone can be held directly against the voice port. If the
SCBA has a voice amplifier, the same rule applies. Ensure that the secondary microphone is uncovered. If
possible, point the secondary microphone toward the noise source.
5.17 PTT OPTIONS
The radio can be programmed via RPM2 with one of the following PTT options:
• Radio and Accessory – In this mode, when the radio is PTT’d the audio source will correspond with
the PTT source.
If the source of PTT is radio, the audio is routed via the radio microphone.
If the source of PTT is an external microphone accessory, the audio is routed via the external
microphone accessory.
• Accessory Only - Any PTT input will have the audio routed through the external microphone
accessory.
The Bluetooth Speaker Mic is unaffected by this setting. PTTing the Bluetooth Speaker
Mic always results in audio being routed via the Bluetooth Speaker Mic.
5.18 VOICE ANNUNCIATION
When enabled via programming, Voice Annunciation provides audible feedback for various radio
operations. The radio can be programmed to play an audio message for any or all of the following. This
message can be a pre-recorded (canned) message or a user-recorded message.
• Zone changes
• Channel changes
• System changes
• Encryption On/Off
• Noise Cancellation On/Off
• Scan On/Off
• Talkaround On/Off
• Monitor Mode On/Off
• 2 or 4 Position switch change
44
Page 46
14221-1800-2000, Rev. D
for the various options that can be programmed to the radio buttons
1. Press the Menu/Select button to access the menus.
. Toggle encryption
enabled/disabled using the Menu/Select button. This option is grayed out if
, or if Encryption Mode in the
radio’s personality is programmed “Forced On.”
for the various options that can be programmed to the radio buttons
NOTE
NOTE
For more information on configuring the radio for Voice Annunciation, refer to the Voice Annunciation
Feature manual 14221-7200-6110.
5.19 ENABLE/DISABLE ENCRYPTION
A switch or a button on the radio can be programmed to enable/disable encryption.
See Section 7.4
and switches.
Or
Turn encryption on or off via the Security Menu:
2. Use the or button to highlight and select the SECURITY menu.
3. Use the or button to highlight ENCRYPTION
any switch is programmed for encryption
• If a channel is programmed to be encrypted, an optional key icon appears on t he main display when
encryption is enabled. The system must also be programmed for encryption.
• When encryption is enabled and you use any channel not configured for encryption, the radio allows
PTT. The signal is transmitted unencrypted.
• Systems configured for Global Encryption (enabled in the Security menu) can display an optional
Global Encryption icon in addition to or instead of a key icon (Section 6.20.3).
5.20 TRANSMIT ENABLE/DISABLE
When transmit is disabled, all forms of transmission from the radio are disabled, including Bluetooth.
This is designed for use in explosive atmospheres.
If enabled via programming, use the A/B switch to enable or disable transmit.
See Section 7.4
and switches.
45
Page 47
14221-1800-2000, Rev. D
1. Press Menu/Select button to access the main menu.
6.4 and 7.2 for more information.
A button on the radio can be programmed for Channel Guard Override (see Section
NOTE
NOTE
5.21 CHANNEL GUARD (ANALOG CONVENTIONAL ONLY)
Channel Guard is Harris’s trademark for CTCSS (tone squelch) and CDCSS (digital tone squelch).
The Channel Guard menu is only accessible if the System is setup for CG SEL in the
radio’s personality.
To select the Channel Guard tone:
2. Use or to display the CALL menu.
3. Use or to highlight CHANNEL GUARD and press the Menu/Select
button.
4. Use or to highlight RECEIVE GUARD or TRANSMIT GUARD
and press the Menu/Select button.
5. Use or to highlight the desired option from the list and select using
the Menu/Select button.
6. The Channel Guard frequency is displayed on the main display.
The Channel Info screen and Channel Edit screen will change depending on this selection. See Sections
7.4).
46
Page 48
14221-1800-2000, Rev. D
1. Press Menu/Select button to access the main menu.
appears. Calls are now made on the receive
menu. Power
NOTE
5.22 USE TALKAROUND TO BYPASS REPEATER (ANALOG AND P25
CONVENTIONAL ONLY)
You can bypass the repeater system to communicate directly with other radios on your current channel’s
receive frequency. This is useful if you are out of range of a repeater or if a repeater is busy. You will
need to be in range of the other radio.
2. Press or to display the CALL menu.
3. Press or to highlight TALKAROUND MODE.
4. Press the Menu/Select button to toggle TALKAROUND MODE to
ENABLED.
5. The optional Talkaround icon
frequency until you disable talkaround mode via the CALL
cycling the radio does not disable talkaround.
Or
A button or switch can be programmed to toggle talkaround enable/disabled. See Section 7.4 for the
various options that can be programmed to the radio buttons and switches.
If the Talk-Around Indication feature is enabled in RPM2, the radio will play a unique grant tone when a
call is placed on a simplex channel or when Talk-Around has been enabled on a duplex channel. This
feature applies to both Analog and P25 Conventional systems. It optionally allows the radio to also play
the same tone when it receives a call while operating in simplex or Talk-Around. If configured, the radio
plays the tone at the selected volume level.
The tone will not play on systems configured with MDC.
Talk-Around Indication can be specified for each individual Analog and P25 Conventional system
configured in personality. Th e following options can be selected, and apply only when the radio is on a
simplex channel or when Talk-Around has been enabled by the user:
• Disabled: (This is the default option.) When this option is selected, the radio plays the standard grant
tone when a call is placed. The radio does not play a tone when a call is received.
• Transmit Only: When this option is selected, the radio plays a different “Talk-Around” grant tone
when a call is placed. The radio does not play a tone when a call is received.
• Transmit & Receive: When this option is selected, the radio plays a different “Talk-Around” grant
tone when a call is placed, and at the beginning of a received call.
47
Page 49
14221-1800-2000, Rev. D
In the radio personality, the “Alert Tone” parameter needs to be enabled for each
1. Press Menu/Select button to access the main menu.
is displayed in the top of the radio display when Type 99 is enabled.
NOTE
channel on the Conventional Frequency Set. The “Ready To Talk Tone” parameter
must also be enabled for the Talk Around Indication tone to be played when the radio
is keyed.
5.23 TYPE 99 OPERATION
Type 99 is Harris' name for in-band, two-tone sequential signaling. It is a conventional signaling protocol
used to control the muting and unmuting of a radio. This signaling is commonly used for selective calling
of individual units or groups of units in a conventional system.
In Type 99 tone systems, calls are not heard until the radio detects the proper two-tone sequence. This, in
conjunction with squelch, prevents the user from hearing noise or undesired conversations. When the
radio detects the second tone, it sounds the appropriate Type 99 alert tone. After the second tone stops,
the receiver audio path is opened in order for the user to receive messages.
5.23.1 Enable/Disable Type 99
2. Press or to display the CALL menu.
3. Press or to highlight T99 TOGGLE.
4. Press the Menu/Select butt on to change T99 TOGGLE between ENABLED and DISABLED. T99
Or
A button or switch can be programmed to enable/disable Type 99 (see Section 7.4).
5.23.2 Disable After PTT
If this option is programmed in RPM2, Type 99 is disabled after the radio user activates the PTT. This
allows the radio user to monitor traffic on the channel (after a PTT action) without pressing the monitor
button.
Can be used in conjunction with the “Auto Reset” option (see Section 5.23.3) to disable Type 99 after a
PTT and automatically reset, or enable, Type 99 after 30 seconds.
5.23.3 Auto Reset
If this option is programmed in RPM2, Type 99 is automatically reset, or turned back on, after 30
seconds. Can be used in conjunction with the “Disable After PTT” option (see Section 5.23.2) to disable
Type 99 after a PTT and automatically reset, or enable, Type 99 after 30 seconds.
48
Page 50
14221-1800-2000, Rev. D
1. Press the Menu/Select button to access the main menu.
and press the Menu/Select
to highlight the desired unit from the list and press the
5. Press PTT to send the page.
For conventional or P25 Conventional systems, DTMF tones only play if the current
NOTE
5.24 CALL ALERT (PAGE)
5.24.1 Send Alert
2. Press or to display the CALL menu.
3. Press or to highlight CALL ALERT
button.
4. Press or
Menu/Select button, or select KEYPAD to enter the Unit ID.
5.24.2 Receive Alert
1. When receiving a Call Alert, the radio display s the calling radio’s name or Unit ID.
2. The radio rings and indicates a missed call. The ring sounds continuously until you press PTT, press
the CLR MISSED softkey, change group/system, or power cycle the radio.
5.25 DTMF
The XL-200P supports the transmission of DTMF tones corresponding to the numbers/characters on the
keypad. To overdial numbers/characters, press and hold the PTT button, and then press the corresponding
keys one at a time on the keypad. Valid keys for DTMF tones are: (1, 2, 3, 4, 5, 6, 7, 8, 9, *, 0, and #).
system is programmed for DTMF (part of general System configuration). DTMF tones
are always enabled for P25 Trunking systems.
5.26 AUDIO PLAYBACK
The Audio Playback feature allows the user to playback a previously received call. Recordings are stored
in the r a dio’ s R AM and are not persistent across power cycles. The radio stores the last five (5) recorded
calls up to 1 minute each.
A button on the radio can be programmed to replay the last recorded call. To playback the last received
call from a button:
1. Press the button programmed for audio playback. The last call received before the button was pressed
is played each time the button is pressed.
2. Additional incoming calls will be recorded in the background, but pressing the button continues to
replay the captured call until reset.
49
Page 51
14221-1800-2000, Rev. D
1. Press the Menu/Select button.
and press the
and press the Menu/Select
4. Press the BACK soft key to exit the scan menu.
NOTE
3. To reset the feature and allow a new call to be captured, press and hold the button until you hear a 2tone chirp. At this point the button can be used to capture an new incoming call.
You can also playback one of the last five calls received via the menu. To playback a previously received
call from the menu:
2. Press or to display the CALL menu.
3. Press or to highlight AUDIO PLAYBACK
Menu/Select button.
4. Select the desired call from the list (the most recent call is at the top of the
list) and press the select button. The selected call will be played.
• If a button is also programmed for Audio Playbac k, pre ssin g the button
replays the call that selected in the menu. The feature must be reset as
above in order to use the button to capture a new call.
• If a button is not programmed for Audio Playback, then you must
navigate back to the menu to play the call again.
Any incoming call that occurs during playback preempts the playback.
5.27 START SCAN
This procedure assumes that the scan list has been added and the radio is not in active scan. Refer to
Section 6.13 f or sc an se tup o r Section 5.28 for stopping scan. Refer to Section 6.14.1.1, Section 6.14.1.2,
and Section 6.14.1.3 for home and priority channel descriptions.
1. Press the Menu/Select button to access the main menu.
2. Press or to display the SCAN menu.
3. Press or to highlight START SCAN
button. START SCAN text changes to STOP SCAN.
5. The scan icon is displayed on the idle display when scanning is enabled.
50
Page 52
14221-1800-2000, Rev. D
1. Press the Menu/Select button to access the main menu.
for the various options that can be programmed to the radio buttons
1. Press the Menu/Select button to access the main menu.
1. Press the Menu/Select button to access the main menu.
NOTE
NOTE
Or
2. Press or to display the SCAN menu.
3. Press or to highlight SCAN LISTS and press the Menu/Select button.
4. Press or to highlight the desired SCAN LIST and press the START SCAN soft key.
Or
A switch or button on the radio can be programmed to start/stop scan.
If a switch is programmed for start/stop scan, the menu for starting and stopping scan
is disabled.
See Section 7.4
and switches.
5.28 STOP SCAN
2. Press or to display the SCAN menu.
3. Press or to highlight STOP SCAN and press the Menu/Select button.
4. Press the BACK soft key to exit the scan menu.
Or
2. Press or to display the SCAN menu.
3. Press or to highlight SCAN LISTS and press the Menu/Select button.
4. Press the STOP SCAN soft key.
51
Page 53
14221-1800-2000, Rev. D
starting and
s options that can be programmed to the radio buttons
NOTE
NOTE
NOTE
Or
A switch or button on the radio can be programmed to start/stop scan.
If a switch or button is programmed for start/stop scan, the menu for
stopping scan are disabled.
See Section 7.4 for the variou
and switches.
5.29 MONITOR AND SQUELCH TYPES (CONVENTIONAL ONLY)
The monitor function allows you to temporarily turn off selected squelch to monitor for traffic that may
not normally break squelch. The type of squelch used depends on an analog or digital channel. A button
or switch on the radio can be programmed to start or stop Monitor (see Section 7.4 for the various options
that can be programmed to the radio buttons and switches.).
For analog channels, there is:
• Noise squelch - any received signal breaks squelch.
• Continuous Tone Coded Squelch (CTCSS) - squelch is selective based on tone code.
• Continuous Digital Coded Squelch (CDCSS) - squelch is selective based on digital code.
For digital channels, there is:
• Monitor squelch - any received digital signal breaks squelch.
• Normal squelch - Received Network Access Code (NAC) must be correct to break squelch.
• Selective squelch - Received NAC and talkgroup Identification (ID) or unit ID must be correct to
break squelch.
During encrypted operations, the radio only unmutes when receiving with the same key.
52
Page 54
14221-1800-2000, Rev. D
1. Press the Menu/Select button to access the main menu.
an list. If you do not add the channel back
scan list when you cycle radio power
11. Press the BACK soft key to exit the scan list display.
NOTE
5.30 NUISANCE DELETE
A channel can temporarily be deleted from the scan list. The selected channel, priority 1, and priorit y 2
channels cannot be nuisance deleted.
A button or switch on the radio can be programmed for nuisance delete (see Section 7.4 for the various
options that can be programmed to the radio buttons and switches).
Nuisance delete can only be performed on the active scan list.
To perform nuisance delete from the menu:
2. Press or to display the SCAN menu.
3. Press or to highlight SCAN LISTS and press the Menu/Select button.
4. Press or to highlight the scan list and press the Menu/Select button.
When scanning is started, indicates the active scan list; when scanning is
stopped, indicates the active scan list.
5. Press or to highlight the desired channel.
6. Press the OPTIONS soft key.
7. Press or to highlight NUISANCE and press the Menu/Select button.
8. The icon appears next to the channel and it will not be scanned.
9. Highlight the channel, press the OPTIONS soft key, and select ADD BACK to add channel back to sc
to the list, the channel will return to the
or activate a personality.
10. Press the BACK soft key to exit the channel list.
53
Page 55
14221-1800-2000, Rev. D
y button on the radio or the speaker
The length of time you need to hold the button is configured in
The radio can also be programmed to send an Emergency Alarm in addition to or in place of the
the radio is transmitting or press PTT to talk.
If enabled via programming, you can clear an emergency by pressing the
Monitor/Clear function and then the emergency
button.
5.31 EMERGENCY OPERATION
The XL-200P ca n be programmed to enable emergency mode. Unit name displays on dispatcher console
if an emergency signal is received from another XL-200P on a digital channel.
5.31.1 Declaring an Emergency Call
1. Press and hold the emergenc
microphone.
RPM2.
2. The emergency icon is displayed on the idle display.
• For digital channels, the radio transmits the talkgroup or radio ID to the dispatch console and
receiving radio.
• T he radio can be programmed to have a dedicated emergency channel, which can be activated
from analog or digital channels.
•
emergency call (P25 modes).
The radio goes through transmit and receive cycles if so configured. Speak into the microphone while
3. To exit emergency, power cycle the radio or select EXIT EMERGENCY
from the CALL menu.
button programmed for the
5.31.2 Receiving an Emergency Call
When receiving an Emergency Call, an alert beep sounds (if tones are enabled) and an emergency
indication is displayed.
The unit ID and/or unit name of the unit in emergency is displayed.
While the emergency display is active, press PTT to respond to the emergency caller.
5.31.3 Stealth Emergency
The radio can be programmed with the following emergency behavior:
• No audio indications when declaring an emergency.
Or
• No visual indications when declaring an emergency.
Or
• No audio and no visual indications when declaring an emergency.
During stealth mode, the radio will not receive any type of call. Once the user presses the PTT button, the
radio display and audio return to normal.
54
Page 56
14221-1800-2000, Rev. D
5.32 MDC-1200 (ANALOG CONV E NTIONAL ONLY)
MDC-1200 is a legacy in-band signaling protocol that provides the radio with the ability to transmit and
receive a unique PTT ID. This PTT ID can be decoded by receiving radios and displayed as a
hexadecimal number or an alias string. In addition, MDC-1200 provides radios with the ability to transmit
emergency status to a console. Refer to the MDC-1200 Feature Manual, 14221-7200-6000, for complete
instructions on configuring and using this feature.
5.32.1 Normal PTT Operation
If MDC signaling on PTT press is enabled in RPM2, the radio t ransmits an MDC PTT ID message when
PTT is pressed. If the Sidetone option is enabled in RPM2, the ra dio plays a Ready-to-Talk ( RTT) to ne
after the MDC pre-signaling has been transmitted.
If MDC signaling on PTT release is enabled (in RPM2), the radio transmits post-call MDC signaling
when PTT is released.
• IF STE is enabled (in RPM2), the MDC post-call signaling is transmitted after STE is sent on PTT
release only.
• MDC post-call signaling is also sent when there is a radio unkey due to Carrier Control Timeout
(CCT). Normal CCT alert tones occur prior to unkey.
5.32.2 MDC PTT ID Receive Handling
When the radio receives an MDC PTT ID, it searches the MDC ID Alias List for an alias associated with
the ID. If one is found, it displays the alias. If none is found, the radio displays the ID in hexadecimal.
5.32.3 Emergency Declaration
Emergency declaration is accomplished by the radio generating an MDC Emergency PTT message. An
Emergency is considered acknowledged when the radio receives an “Ack To Emergency” PTT message
with an ID which matches its own ID. If Emergency Audio is enabled and the PTT Sidetone option is
enabled, the radio plays the Ready-to-Talk tone after the MDC Emergency PTT signaling is transmitted.
• If an MDC Alert on ACK is enabled, the radio plays an ACK tone when the MDC emergency is
acknowledged.
• If audio tones are enabled, the radio plays an ACK tone i f the emergency is not acknowledged within
the programmed number of retries.
55
Page 57
14221-1800-2000, Rev. D
1. At main display, press the Menu/Selec t bu tton to access the main menu.
s if
6. ADVANCED OPERATI O NS
6.1 VIEW/CHANGE PERSONALITIES
Personalities contain radio programming information such as frequencies, channels, stations, and talk
groups. Up to 10 different personalities can be stored in the radio, but only one can be activated at a time.
6.1.1 View Personalities
To view a personality:
2. Press or to display the UTILITY menu.
3. Press or to highlight PROGRAM and press the Menu/Select button.
An arrow indicates the currently active personality.
4. Press the OPTIONS soft key.
5. Select VIEW PLAN INFO to view.
6. The radio displays the plan’s filename. Personality information appear
the field was filled out in RPM2.
6.1.2 Change Active Personality
To change the active personality:
1. At main display, press the Menu/Selec t bu tton to access the main menu.
2. Press or to display the UTILITY menu.
3. Press or to highlight PROGRAM and press the Menu/Select button.
4. Press or to highlight the desired personality and press the Menu/Select
button. indicates the currently active personality .
56
Page 58
14221-1800-2000, Rev. D
prompted to enter the PIN before activation
screen is displayed while plan activation is in
You cannot activate a personality when the radio is transmitting an
in the fill or some other invalid parameter.
1. Press the Menu/Select button to access the main menu.
5. Press the YES soft key to confirm personality activation. If the personality
has a power-up PIN, you are
continues.
6. The IN PROGRESS
progress.
7. If personality is activated, the radio displays PLAN COMP LETE followed
by the name of the personality. Press the OK soft key.
•
emergency.
• A FAILED message may be displayed for errors such as invalid syntax
6.2 SITUATIONAL AWARENESS (SA) – P25 CONVENTIONAL ONLY
Situational Awareness is a feature in which the XL-200P receives SA position from other units
configured to send the SA packets. The SA display shows the positions of the other radios (units) relative
to the XL-200P. To make use of SA, all radios need to have a uniquely programmed Unit ID.
2. Press or to display the UTILITY menu.
3. Press or to select GPS and press the Menu/Select button.
4. Press or to select POSITION INFO and press the Menu/Select
button.
5. Press the NEXT soft key.
57
Page 59
14221-1800-2000, Rev. D
The color of each unit
indicates its status as follows. Only one status can be shown at a time and
8. Press or to zoom the display distance of current unit.
to display
update information, or
select EXIT.
1. Press the Menu/Select button to access the main menu.
2. Press or to display the ZONE menu.
3.
VIEW ZONE
NOTE
6. Press or to view the location of each unit.
are listed in prior ity order:
• Grey – Unselected, no status
• Red – Unselected, In Emergency
• Orange – Unselected, Low Battery
• Blue - Unselected, Scanning
• Green – Selected, no status
• Green/Red – Selected, In Emergency
• Green/Orange – Selected, Low Battery
• Green/Blue - Selected, Scanning
7. GPS of this radio is shown by the center dot as follows:
• Green – Tracking
• Orange – Last known position
• Red – Searching
9. Press the OPTIONS soft key. From here, select UNITINFO
details about the selected unit, select REFRESH to
6.3 USER-DEFINED ZONES/SYSTEMS
6.3.1 Command Tactical Zone
A Command Tactical Zone is defined at the radio.
To create a Command Tactical Zone:
Press or to highlight <USER-DEFINED> and press the
soft key.
A Command Tactical Zone is reset when a Personality is activated.
58
Page 60
14221-1800-2000, Rev. D
(up to 16 characters are
8. After adding all desired channels/groups, press the BACK soft key.
1. Press the Menu/Select button to access the main menu.
to view the groups/channels in the
4. Press the OPTIONS soft key.
5. Press or to select EDIT ZONE to create a zone, or RENAME ZONE to rename the Command Tactical Zone
allowed).
6. Press or to scroll through existing systems. Press or to
highlight desired channel/group.
7. Press the Menu/Select button to add or remove channel/group.
9. Activate the Command Tactical Zone by selecting the SET ACTIVE soft
key on the USER DEFINED screen, or by pressing the Menu/Select
button when <USER DEFINED> is highlighted on the Zone menu.
10. After a creating a Command Tactical Zone, select OPTIONS to edit the
Command Tactical Zone, delete channels/groups, clear the zone, and
rename the zone.
6.3.2 Mixed System Zone
Mixed System Zones are defined in RPM2 and cannot be edited on the radio. If a Mixed System Zone is
not configured in RPM2, it will not appear on the radio. Up to 50 Mixed System Zones can be defined.
You can view details about each channel/group. A user programmable button can be defined to scroll
through just the mixed system zones.
2. Press or to display the ZONE menu.
3. Press or to highlight the desired zone (Note: Zones are indicated by the icon) and select VIEW ZON E
zone list.
59
Page 61
14221-1800-2000, Rev. D
1. Press while on the idle display.
2.
CONVENTIONAL
3.
4.
. You may now select and change the values of the displayed channel parameters.
The password remains active until power cycle. Refer to Section 7.2 for more information.
1. Press the Menu/Select button to access the main menu.
2.
3.
and press the Menu/Select
4.
to scroll through available audio settings. Press the
.
to prevent
holster or you are
Enable or disable keypad tones. When enabled, the
5. Press the BACK soft key to exit menu.
6.4 CH INFO MENU
The Channel Information (CH INFO) menu displays information about the currently selected channel.
The information displayed varies between conventional and trunked systems.
Press or to scroll through the programmed channel settings.
OR P25 CHANNELS ONLY:
Press the EDIT soft key.
Enter the password
6.5 AUDIO SETTINGS
Set audio settings such as speaker mute, noise cancellation, PTT, and tones.
Press or to display the UTILITY menu. Press or highlight AUDIO SETTINGS
button.
Press or
Select/Menu button to change settings as desired:
• SPEAKER - Mute or Unmute the speaker audio.
• NOISE CANCELLATION - Enable or disable noise cancellation
Noise cancellation reduces background noise during transmit.
•PTT - Enable or disable Push-To-Talk (PTT). Disable PTT
accidental keying, such as when the radio is in a
getting into a car.
• TONES - Enable or disable alert tones (see Table 5-6).
• K EYPAD TONES -
radio plays a tone when a button on the keypad is pressed.
60
Page 62
14221-1800-2000, Rev. D
1. Press the Menu/Select button to access the main menu.
2.
3.
to highlight DISPLAY SETTINGS and press the
4.
Change the color scheme of the top and front
Turn front display backlight on, off, or
Set brightness level of front display. A level
Specify how long the radio needs to be inactive
Specify how long the top display’s backlight will
Set the brightness level of the top display. A
Specify how long the radio needs to be inactive
Set orientation of top display to be viewed from
200P changes top display to be
viewed from back if an external microphone or speaker is attached.
• INDICATOR LED - Toggle the indicator LED ON/OFF.
5. Press the BACK soft key to exit the menu.
6.6 DISPLAY SETTINGS
Press or to display the UTILITY Menu. Press or
Menu/Select button.
Press or and the Select/Menu button to change settings as desired:
• COLOR SCHEME -
displays for optimum viewing in day/night conditions.
• FRONT BACKLIGHT -
momentary.
• FRONT BRIGHTNESS -
of 0 has same effect as turning off backlight.
• FRONT TIMEOUT -
before the front display’s backlight turns off.
• T OP BACKLIGHT -
remain lit: MOMENTARY, ON, or OFF.
• TOP BRIGHTNESS -
level of 0 turns off top display and indicator (TX/RX) LED.
• TOP TIMEOUT -
before the top display’s backlight turns off.
• TOP ORIENTATION -
radio: FRONT, BACK, or AUTO.
When AUTO is selected, the XL-
Otherwise, the display can be viewed from the front.
61
Page 63
14221-1800-2000, Rev. D
1. Press the Menu/Select button to access the main menu.
2.
3.
and press the Menu/Select
4.
Set unit of measurement of displayed linear units:
Set unit of measurement of displayed angular
of displayed position information:
),
or
Universal Transverse Mercator (UTM).
5.
1. Press the Menu/Select button to access the main menu.
2.
3.
and press the Menu/Select
4.
NOTE
6.7 GPS SETTINGS
The GPS SETTINGS men u ite m only appears if enabled in RPM2 and the feature is
installed.
Press or to display the UTILITY menu. Press or to highlight GPS SETTINGS
button.
Use or and the Select/Menu button to change settings as desired:
• GPS - Enable or disable internal GPS.
• POSITION INFO - See Section 6.8.
• LINEAR UNITS -
STATUTE, METRIC, or NAUTICAL.
•ANGULAR UNITS units: CARDINAL, DEGREES, or MILS.
•POSITION FORMAT- Set format
Latitude/Longitude Degrees Minutes Seconds (LAT/LONG DMSLAT/LONG DM, Military Grid Reference System (MGRS),
Press the BACK soft key to exit the menu.
6.8 POSITION INFO
The Position Info screen displays the radio user’s location information. GPS must be enabled in the GPS
Settings (see Section 6.7).
Press or to display the UTILITY menu. Press or to highlight POSITION INFO
button.
Press or to scroll through available location information.
62
Page 64
6.9 WI-FI
The XL-200P supports programming via Wi-Fi. Refer to Appendix A for information on configuring WiFi.
To enable Wi-Fi programming mode on the radio:
1. Ensure the radio is powered off.
2. Press and hold the bottom side button and PTT button (see Figure 4-1).
14221-1800-2000, Rev. D
Figure 6-1: Enabling Wi-Fi
3. Power on the radio.
4. The WIFI INSTALL ACTIVE screen is displayed (Figure 6-2). The radio displays
DISCONNECTED if not connected to a wireless network, or CONNECTED if connected to a
wireless network.
Figure 6-2: Wi-Fi Install Active
63
Page 65
14221-1800-2000, Rev. D
1. Press the Menu/Select button to access the main menu.
and press the Menu/Select
1. Press the Menu/Select button to access the main menu.
and press the Menu/Select
and press the Menu/Select
ed on and has discovery mode
NOTE
6.10 BLUETOOTH
The BLUETOOTH menu i tem only appears if enabled in RPM2 and if the f eature is
installed.
6.10.1 Enable Bluetooth
2. Press or to display the UTILITY menu.
3. Press or to highlight BLUETOOTH
button.
4. Press or to highlight ENABLED and press the Menu/Select button to
toggle YES/NO.
6.10.2 Pair Devices
2. Press or to display the UTILITY menu.
3. Press or to highlight BLUETOOTH
button.
4. Press or to highlight PAIRING MGMT
button.
5. Make sure device being paired is power
enabled in order to pair with the XL-200P.
If no devices are found and Bluetooth is enabled, only the ADD NEW soft
key is available. If devices are paired, the OPTIONS soft key appears.
6. Press the ADD NEW soft key to select a device to pair.
64
Page 66
14221-1800-2000, Rev. D
9. Press or highlight the desired device and press the PAIR softkey.
10. Pairing progress is displayed.
Enter the pin code and select OK.
1. Press the Menu/Select button to access the main menu.
Set time zone relative to Universal Time Coordinated
5. Press the BACK soft key to exit.
7. A list of available Bluetooth devices appears.
8. Press the REFRESH soft key to refresh the device list if the desired device
does not appear.
• For Bluetooth 2.0 devices, a pin code screen appears.
• For Bluetooth 2.1 devices, a PASSKEY accept/deny screen appears.
Select ACCEPT.
Accept the passkey on the Bluetooth 2.1 device as well.
11. A message appears when pairing is complete. Select OK. The paired device
is then displayed in the PAIREDDEVICES list.
6.11 CLOCK SETTING S
2. Press or to display the UTILITY menu.
3. Press or to highlight CLOCK SETTINGS and press the Menu/Select
button.
4. Use or and Menu/Select button to change settings as desired:
• TIME FORMAT- Set 12 or 24 hour time display format.
• TIM E ZONE -
(UTC).
65
Page 67
14221-1800-2000, Rev. D
1. Press the Menu/Select button to access the main menu.
2. Press or to display the UTILITY menu.
and press the Menu/Select
button.
e Menu/Select
Use only Harris approved batteries. Injury could occur from using incorrect
1. Press the Menu/Select button to access the main menu.
and press the
WARNING
6.12 BATTERY SETTI NG S
3. Press or to highlight MAINTENANCE
4. Press or to highlight BATTERY INFO and press th
button.
5. Battery information is displayed (state, voltage, capacity, and chemistry).
battery.
6.13 SELECT LANGU AG E
To change the language displayed by the XL-200P:
2. Press or to display the UTILITY menu.
3. Press or to highlight CHANGE LANGUAGE
Menu/Select button.
4. Press or to hi ghlight the desired language and press the Menu/Select
button.
66
Page 68
14221-1800-2000, Rev. D
1. Press the Menu/Select button to access the main menu.
NOTE
6.14 SET UP SCAN
These procedures are used to set up the scan list, home channels, and priority channels.
2. Press or to display the SCAN menu.
3. Press or to highlight SCAN LISTS and press the Menu/Select button.
Refer to the following sections.
When using Preemptive Priority Scan, the frequencies in the list need to be unique.
6.14.1 Default, Priority 1, and Priority 2 Channels
6.14.1.1 Default Channel
This is the currently selected channel and is the channel you transmit on by default when you press PTT
while the radio is actively scanning and is not responding to a just received call. Responding to a call the
radio just received while scanning is called hang time. If hang time is set to 0 in RPM2, the radio always
transmits on the default channel in scan.
6.14.1.2 Priority 1 Channel
This channel will be scanned more often than other channels in the list and will be scanned in between
every other channel in the scan list. An example scan sequence would be P1 (priority 1), C2, P1, C3, P1,
C4, etc. In addition, the priority channel will be scanned even while actively receiving on a non-priority
channel. For example, if the radio is actively receiving on C3 and activity is detected on P1, the radio will
drop C3 and switch to P1.
6.14.1.3 Priority 2 Channel
This channel will also be scanned more often than others. An example scan sequence would be P1, C2,
P1, C3, P1, C4, P2, C5, P1, C6, P1, C7, P1, C8, P2, C9 etc. In addition, this channel will be scanned even
while actively receiving on a non-priori ty channe l. For exampl e, if the r adio is act ively rec eiving on C 3
and activity is detected on P2, the radio will drop C3 and switch to P2. Additionally, activity on P1 can
also preempt P2, but P2 cannot preempt P1.
6.14.2 Trunked/Conventional Scanning
Trunked/conventional scanning adds the ability to scan multiple conventional and P25 conventional
channels while still maintaining P25 trunked radio operation. In essence, the radio is able to scan a
conventional scan list while still receiving a P25 trunked control channel and receiving P25 trunked
calls. Selection of which conventional scan list is associated with a given trunked system is done in
RPM2 and cannot be changed on the radio. However, a user with access to the necessary menu layout
(see Section 5.8) is allowed to edit the scan list members (both trunked groups and conventional channels
on the selected Conventional Priority System). As the number of conventional channels being scanned
increases, the time between scanning each channel increases (roughly 250 milliseconds per channel), with
67
Page 69
14221-1800-2000, Rev. D
enabled, the radio is always scanning. You cannot stop scanning, start normal
1. Press the Menu/Select butt on.
CHAN
8. Press the Menu/Select button to toggle selection.
NOTE
NOTE
the consequent increase in the number of calls that will late-enter. In order to avoid missing calls, it is
recommended to keep the number of conventional channels being scanned to eight (8) or fewer.
The trunking site must have roaming set to Enhanced CC.
6.14.3 Vote Scan (Analog and P25 Conventional Only)
If vote scan is enabled via RPM2, the radio automatically selects the strongest
signal ensuring that the best audio quality is delivered to the user. If vote scan is
scanning, or monitor the channel. The scanning icon on the idle screen indicates
that the radio is vote scanning versus, regular scanning.
If Talkaround is enabled, Vote Scan is dis ab le d un t il Talkaround is disabled again.
6.14.4 Edit Scan List
Depending on the scan list options selected in RPM2, you may be able to add or remove channels/groups
from the scan list.
2. Press or to display the SCAN menu.
3. Press or to select SCAN LISTS.
4. Press or to highlight the scan list and press the Menu/Select button.
5. Press or to highlight channel/group.
6. Select OPTIONS.
7. Press or to select ADD CHAN/DELETE CHAN, SET PRI1, SET PRI2, REMOVE PRI, or NUISANCE/ADD BACK.
When a channel is not grayed out in the list, DELETE
appears. When a channel/group is grayed out (not in list), ADD CHAN
appears.
68
Page 70
14221-1800-2000, Rev. D
1. Press the Menu/Select button.
to highlight SET PRI1 or SET PRI2 and press the
Menu/Select button. A Priority 1 channel appears with a P1 and a Priority 2
6.14.5 Set or Remove Priority 1 and Priority 2 Channels
Priority channels are scanned more often than non-priority channels. Note that P1 and P2 can only be set
if configured as “Keypad” and the scan list is not set to “Fixed” in RPM2.
2. Press or to display the SCAN menu.
3. Press or to highlight SCAN LISTS and press the Menu/Select button.
4. Press or to highlight channel/group.
5. Select OPTIONS.
6. Press or
channel appears with a P2.
7. Select REMOVE PRI to remove priority.
6.14.6 Custom Scan Lists
The Mixed Zone Scan (MZS) feature gives the user the capability to scan based on a custom scan list that
is assigned at the system level. The Custom Scan (CS) list can contain System and Channel/Group
configurations across P25 Trunked, P25 Conventional, and Analog Systems. When a Custom Scan List is
assigned to a P25T system, the radio can scan P25T, P25C and Analog systems. When assigned to a
P25C or Analog system, the radio only scans conventional channels. MZS also gives the user the
capability to scan beyond the selected system group set.
• P25T Scan
When a custom scan list is assigned to a P25T system, the user has the ability to scan P25T, P25C,
and Analog groups/channels. All P25T systems must have the same WACN, System ID, and Unit ID
to be added to the custom scan list. If P25C and/or analog channels are added to the custom scan list,
the radio will scan them using the Trunked/Conventional scan feature described in section 6.14.2, and
will override any other conventional scan list that may have been programmed in RPM2.
• P25C and Analog Scan
When a custom scan lists is assigned to a P25C or Analog System, the user has the ability to scan
P25C and Analog channels. P25T systems are ignored.
Custom scan list can be created in RPM or at the radio. The radio supports up to 10 Custom Scan lists,
with up to 100 channels/groups in each.
69
Page 71
14221-1800-2000, Rev. D
1. Press the Menu/Select button.
and press the
the newly added scan list and press the
e desired group/channel and press the
From here, you can add/delete channels from the scan
NOTE
6.14.6.1 Create Custom Scan List
To create a custom scan list at the radio:
2. Press or to display the SCAN menu.
3. Press or to highlight ASSIGNED CUSTOM LIST
Menu/Select button.
4. Press the OPTIONS softkey.
5. Select ADD SCAN LIST.
6. Press or to highlight
VIEW/EDIT soft key.
7. Press or to display the desired system.
8. Press or to highlight th
OPTIONS softkey.
list, and set/remove Priority 1 and Priority 2 channels.
When a custom scan list is selected, that list is scanned any time scanning is enabled
for any Trunked, conventional, or P25 Conventional system. To scan only the channels
assigned to a particular system, custom scanning must be turned off.
70
Page 72
14221-1800-2000, Rev. D
and press the Menu/Select
4. Select BACK to exit the scan menu.
and press the Menu/Select
NOTE
6.14.7 Wide Area System Scan (P25 Trunked Only)
Wide Area System Scan (WASCAN) causes the radio to roam across mobile systems when the currently
selected system's control channel is lost. The radio will scan the control channels of other systems.
1. Press the Menu/Select button to access the main menu.
2. Press or to display the SCAN menu.
3. Press or to highlight SITE ROAMING
button to toggle Wide Area System Scan ENABLED/DISABLED.
6.15 RADIO ST ATUS
The status feature is used to send a particular status condition to the site without making a voice call.
There can be up to 10 status conditions programmed into the radio. For each status defined, there is an ID
and an alphanumeric name. The ID is sent to the site and the alphanumeric name appears on the radio
display when the ID corresponds with the information programmed at the site.
A button on the radio can be programmed to send a radio status (see Section 7.4).
1. Press the Menu/Select button to access the main menu.
2. Press or to display the MESSAGES menu.
3. Press or to highlight RADIO STATUS
button.
4. Use or and the Menu/Select button to highlight and select desired
status.
71
Page 73
14221-1800-2000, Rev. D
and press the Menu/Select
the desired
and press the
•Select TOD QUERY to get the time of day.
NOTE
6.16 RADIO MESSAGE
The message feature is used to send a particular message to the site without making a voice call. There
can be up to 10 messages programmed into the radio. For each message defined, there is an ID and an
alphanumeric name. The ID is sent to the site and the alphanumeric name appears on the radio display
when the ID corresponds with the information programmed at the site.
A button on the radio can be programmed to send a radio message (see Section 7.4).
1. Press the Menu/Select button to access the main menu.
2. Press or to display the MESSAGES menu.
3. Press or t o highlight RADIO MESS AGE
button.
4. Use or and the Menu/Select button to highlight and select
message.
6.17 RADIO TEXTLINK
Radio TextLink provides short text messaging functionality for radios. Because of the difficulty of
entering text messages on a radio, predefined "canned" messages and predefined replies can be stored in
the radio. To facilitate sending messages where information must be provided at send time, text message
forms will also be stored in the radio. A form contains up to four (4) text prompts, for which the operator
enters alphanumeric values before sending the message.
6.17.1 Radio TextLink Messages
1. Press the Menu/Select button to access the main menu.
2. Press or to display the MESSAGES menu.
3. Press or to highlight TEXTLINK MESSAGES
Menu/Select button.
4. Press or to display the desired message.
• Press the Menu/Select button to send the message.
• Select CHG CALLEE to change the destination for the message.
72
Page 74
14221-1800-2000, Rev. D
the desired message and press the Menu/Select
Enter text into blank field(s) (up to eight alphanumeric characters) and press
to change the
and press the
to delete
6.17.2 Radio TextLink Forms
Form messages are displayed and stored in the radio as a message in which each field to be filled is
indicated by a question mark (?) followed by one or more asterisks(*). The number of asterisks indicates
the maximum number of alphanumeric characters allowed for that field.
1. Press the Menu/Select button to access the main menu.
2. Press or to display the MESSAGES menu.
3. Press or to highlight TEXTLINK FORMS and press the Menu/Select
button.
4. Press or to display
button.
5.
the NEXT soft key.
6. Select SEND to send the message. Select CHG CALLEE
destination for the message. Select TOD QUERY to get the time of day.
6.17.3 View Received Messages
When the icon appears on the idle d isp lay , there are Radio TextLink messages waiting to be read.
1. Press the Menu/Select button to access the main menu.
2. Press or to display the MESSAGES menu.
3. Press or to highlight TEXTLINK MAILBOX
Menu/Select button. From the mailbox, select OPTIONS
messages, view details of messages, and reply to messages.
73
Page 75
14221-1800-2000, Rev. D
1. Press the Menu/Select button to access the main menu.
and press the Menu/Select
Check antenna and antenna connection. Try
Channel frequency programmed is not valid for
this radio.
NOTE
6.18 FAULTS/ALERTS
is displayed on the idle display when there is a fault. To view and clear faults/alerts:
2. Press or to display the MESSAGES menu.
3. Press or to highlight FAULTS/ALERTS
button.
4. Fault messages are displayed. Press or to hi ghlight the d esired f ault.
Press the OPTIONS soft key delete faults. Press the DETAILS sof t key t o
view details for the highlighted fault.
Possible faults include:
• BATTERY FAULT- Replace battery.
• EEPROM FAULT - Contact Harris.
• RF FAULT - Contact Harris.
• OVERCURRENT -
replacing antenna.
• INVALID SYSTEM - Feature not install e d.
• CH ANNEL FAULT -
5. If you view but do not delete the fault, the alert icon goes away on the idle display.
Contact Harris for assistance with diagnosing a fault.
74
Page 76
14221-1800-2000, Rev. D
and press the Menu/Select
6.19 TONE ENCODE
Tone Encode is a generic tone encoding scheme for call identification when transmitting on a
conventional system. It supports generic user-definable tone encode (up to 15 tones), Type 99 (up to 2
tones) and 5/1 Tone (up to 5 tones) encoding formats.
Tone encoding schemes are used to transmit calls to one or more target radios that have been programmed
with the correct tone decode sequence. When the receiving radio detects its tone decode sequence, it
unmutes on the call.
1. Press the Menu/Select button to access the main menu.
2. Press or to display the CALL menu.
3. Press or to highlight TONE ENCODE
button.
4. Select the desired Tone Encode option from the list.
6.20 ENCRYPTION
6.20.1 Create and Load Keys
Refer to the following documentation for advanced programming and setup instructions:
• Harris OTAR Overview Manual - MM-008069-001
• Network Key Manager Installation and Configuration Manual - MM-008070-001
KVL 3000 Plus Key Variable Loader (KVL) User's Guide
75
Page 77
14221-1800-2000, Rev. D
1. Press the Menu/Select button to access the main menu.
and press the Menu/Select
This will also remove the
1. Press the Menu/Select button to access the main menu.
2. Press or to display the SECURITY menu.
6.20.2 Zeroize Keys from Radi o
It may be necessary to remove keys because of compromise or expiration.
2. Press or to display the SECURITY menu.
3. Press or highlight ZEROIZE KEYS
button.
4. Press the YES softkey to remove the keys.
keysets.
6.20.3 Protected Keys
The Protected Keys feature transfers P25 Voice Keys, from Harris Key Loader to the radio, that have
been wrapped (AES) or encrypted (DES) with Key Protection Keys (KPKs). KPKs are nothing more than
unprotected Key Encryption Keys (KEKs). The KPKs need to be loaded into the radio before the
Protected Keys are l oaded. Once loaded into the radio, the KPKs are used to un wrap (AES) or decrypt
(DES) the Protected Keys.
6.20.4 Global Encryption
Global Encryption can be enabled when encryption keys are loaded on the radio and the selected
Zone/System is encrypted. When Globa l Encr ypti on is enabled on the radio, a Global Key is used for all
encrypted transmissions until:
• Global Encryption is disabled.
• A new personality is activated.
• The active keyset is changed.
• The system is changed.
Global Encryption behavior is available on all channels that support encrypted communications.
3. Press or to highlight GLOBAL ENCRYPTION. Press the
Menu/Select button.
76
Page 78
14221-1800-2000, Rev. D
7. The optional global key icon is displayed on the main display.
1. Press the Menu/Select button to access the main menu.
2. Press or to display the SECURITY menu.
Press the Menu/Select button
1. Press the Menu/Select button to access the main menu.
2. Press or to display the SECURITY menu.
4. Press or to highlight the desired Global Key and press the Menu/Select
button to enable Global Encryption.
5. To change the selected global key, press or to highlight GLOBAL KEY on the SECURITY menu. Press the Menu/Select key.
6. Press or to highlight the global key and press the Menu/Select button.
RPM2 allows Key Numbers to be given Key Names.
6.20.5 Select Keyset
3. Press or to select ACTIVE KEYSET.
to toggle to the inactive keyset.
6.20.6 View Key List
3. Press or to select KEY LIST and press the Menu/Select button.
4. The available key lists are displayed.
77
Page 79
14221-1800-2000, Rev. D
1. Press the Menu/Select button to access the main menu.
press the Menu/Select button to
led if the radio has successfully
NOTE
6.20.7 OTAR Configuration
OTAR is t he over-the-air-rekeying from a KMF and must be enabled for the digital only channel using
RPM2. For OTAR operation, the appropriate KEKs must be loaded into the radio using the Harris Key
Loader or a KVL device.
The KMF Configuration must include the RSI of the KMF and the appropriate Message Number Period.
2. Press or to display the SECURITY menu.
3. Press or to highlight OTAR and
toggle ENABLED/DISABLED.
4. Press or to select OTAR REKEY and press the Menu/Select button to
request that the KMF updates the keys in the radio.
OTAR REKEY is only enab
registered for data operations.
78
Page 80
14221-1800-2000, Rev. D
Ensure that the radio is turned off before connecting the programming cable. After the
if the new frequency is invalid, the display
TX POWER – Transmit power. Toggle between LOW and HIGH.
CAUTION
NOTE
CAUTION
7. PROGRAMMING
This section provides information on front panel programming. Programming can also be accomplished
by creating a plan using a computer with RPM2 installed.
7.1 PROGRAMMING VIA RPM2
Radio Personality Manager (RPM2) is used for the bulk of programmi ng t he XL-200P. With RPM2, you
can fully program the XL-200P using cable 12082-0410-A1.
Removing power during radio programming, or programming the radio with low battery
power could corrupt installation of firmware.
cable is connected, then power on the radio.
7.2 EDIT CHANNEL (ANALOG AND P25 CONVENTIONAL ONLY)
Channels can be edited from the Channel Information (CH INFO) menu display. Most of the displayed
channel parameters can be modified here. Channel edits persist across a power cycle. Loading a
personality clears any channel edits.
Available parameters vary depending on whether the channel is a P25 or analog channel.
1. From the main display, press to access the CH INFO screen.
2. Press or to scroll through the programmed channel settings.
3. Press the EDIT soft key.
Only authorized users should attempt channel editing.
4. Enter the password programmed via RPM2. You do not have to re-enter the
password until you power cycle the radio.
5. Press the ENTER soft key.
6. Highlight and select the parameter to edit. For P25 channels, modify remaining channel settings:
• CHANNEL NAME - Up to 16 alphanumeric characters are allowed.
• RX F REQUENCY - Receive frequency. Note that
reverts to the old frequency (Table 7-1).
• TX FREQUENCY - Transmit frequency.
•
79
Page 81
14221-1800-2000, Rev. D
Select type the radio uses in receive. Select NORMAL, SELECTIVE, or
Squelch type radio uses in receive. Select Noise, CTCSS, or CDCSS. For
ntional analog channel
Code radio looks to unmute the speaker on the receiving radio when CDCSS
squelch is used in conventional mode.
Tone radio uses to break selective squelch on receiving radio. This is available
uses to break selective squelch on receiving radio. This is available
Tone sent by transmitting radio to allow receiving radio to unmute when CTCSS
ow receiving radio to unmute when CDCSS
sk goes away and the channel is no longer
NOTE
NOTE
NOTE
• TALKGROUP – Select a talkgroup for the channel. Talkgroup name cannot be set here.
• RX NAC - Network Access Code (NAC) radio uses for Normal squelch in receive.
• TX NAC - NAC radio transmits to break Normal squelch on receiving radio.
• P25 SQUELCH -
MONITOR.
•RX CH AN GUARD –
a digital channel, the RX CHAN GUARD is used to receive from a Conve
that is on the same frequency and uses the selected Channel Guard.
RX CODE -
squelch is used in conventional mode.
RX TONE - Tone radio looks to unmute the speaker on the receiving radio when CTCSS
7. For analog channel, modify remaining channel settings:
• CHANNEL NAME - Up to 16 alphanumeric characters are allowed.
• TX FREQUENCY - Transmit frequency.
• TX POWER - Transmit power. Toggle between HIGH and LOW.
• RX CHAN GUARD - Squelch type radio uses in receive. Select Noise, CTCSS, or CDCSS.
RX TONE -
when RX squelch is set to CTCSS.
RX CODE - Code radio
when RX squelch is set to CDCSS.
RX CHAN GUARD is not available on this screen if it was enabled from the CALL
menu as per Section 5.21.
•TX CHAN GUARD - Squelch type radio uses in transmit. Select None, CTCSS, or CDCSS.
TX TONE -
squelch is used in conventional mode.
TX CODE - Code sent by transmitting radio to all
squelch is used in conventional mode.
TX CHAN GUARD is not available on this screen if it was enabled from the CALL
menu as per Section 5.21.
8. An asterisk is displayed in front of the CHANNEL label on the main display when a channel has been
edited. The asterisk is NOT shown for TX Power or Talkgroup changes.
When the only item edited is the TX or RX CHAN GUARD values, and then CHAN
GUARD edit is Disabled, the asteri
considered edited. This is the only editable item for which this is true.
The XL-200P supports Over-the-Air-Programming (OTAP) via ProFile Manager. RPM2 creates,
modifies and stores personality information while ProFile Manager delivers the personality over the
network to the desired radios. ProFile Manager also contains the ability to read personality information
over-the-air and save the files, so that RPM2 can modify the information if necessary.
You can interrupt the programming process, if necessary, by depressing the Push-to-Talk (PT T ) but t on o r
declaring an emergency. Once a radio personality update is successfully completed, the radio
automatically resets itself, switches to the new personality, and returns to normal operation. For more
information on using ProFile Manager, refer to software release notes AE/LZT 123 3263/1.
7.4 PROGRAMMABLE BUTTONS AND SWITCHES
7.4.1 P r ogr ammable Buttons
Press while on the main display to view the functions assigned to the programmable buttons. The
programmable buttons are programmed using RPM2. A delay of 0 to 10 seconds can be defined in RPM2
for the programmable buttons. Table 7-2 lists and describes the functions that can be programmed to the
buttons:
Table 7-2: Programmable Button Options
FUNCTION DESCRIPTION
No Operation
Monitor Toggle Toggles Monitor On/Off.
Monitor/Clear Temporarily turn off selected squelch to monitor for traffic that may not normally break
squelch. Also, press this button followed by the emergency button to clear an emergency.
Audio Playback Accesses the AUDIO PLAYBACK menu. See Section 5.26.
Lock Keypad Locks the DTMF keypad, programmable function keys and navigation keys.
Nuisance Delete Performs a Nuisance Delete. See Section 5.30 for more information.
System Up Scrolls up through the list of available systems, stopping at the top of the list.
System Down Scrolls down through the list of available systems, stopping when the end of the list is
reached.
System Up Wrap Scrolls up through the list of available systems, wrapping to the end when the beginning of
the list is reached.
System Down Wrap Scrolls down through the list of available systems, wrapping to the top when the bottom of
the list is reached.
Zone Up Scrolls up through the list of available mixed system zones, stopping at the top of the list. If
no mixed system zones are defined, or there is only one, the user will hear a deny tone
when the button is pressed.
Zone Down Scrolls down through the list of available mixed system zones, stopping when the end of the
list is reached. If no mixed system zones are defined, or there is only one, the user will hear
a deny tone when the button is pressed.
81
Page 83
14221-1800-2000, Rev. D
FUNCTION
DESCRIPTION
Zone Up Wrap Scrolls up through the list of available mixed system zones, wrapping to the end when the
beginning of the list is reached. If no mixed system zones are defined, or there is only one,
the user will hear a deny tone when the button is pressed.
Zone Down Wrap Scrolls down through the list of available mixed system zones, wrapping to the top when the
bottom of the list is reached. If no mixed system zones are defined, or there is only one, the
user will hear a deny tone when the button is pressed.
Channel/Group Bank
Select
Drop Call Drop or terminate any group call that the radio receives.
Send Status Sends a preconfigured status. See Section 6.15 for more information.
Send Message Sends a preconfigured message. See Section 6.16 for more information.
TX Power High/Low Toggle TX Power between LOW and HIGH.
Scan Enable Enable/disable scan.
Secure Enable Toggle Toggles Encryption Mode On/Off. See Sections 5.19 and 6.20 for information on
Home Goes to home channel.
Adjust Squelch Allows the user to adjust the analog squelch level.
Front Backlight Toggles front display’s backlight On/Off/Momentary.
Top Orient Toggles Top Display Front/Back.
Top Backlight Toggles the top display’s backlight On/Off/Momentary.
Flashlight Mode Press and hold to turn on the front and top display backlights. Release the button to turn off
Override
Individual Call Initiate an Individual Call.
OTAR Rekey Initiate an OTAR rekey. See Section 6.20.7.
GPS SA Info Display GPS Situational Awareness (SA) screen.
Site Roaming Enable/disable Site roaming. Site Roaming allows the radio to roam to another site.
Profile Toggle Toggles between the currently active profile (if one has been selected) and no profile.
Numeric Channel
Entry
Select the channel/group bank. If your system has more than 64 channels, this allows you to
select a channel group with channels 65 to 127, 128 to 191, etc.
Encryption.
both displays.
Allow user to pick a different Channel Guard setting for the current channel.
Allows number channel entry.
82
7.4.2 Programmable A/B (Ø/O) Switch
The programmable A/B switch can be programmed for multiple functions, including:
Sections 7.4.3.1 and 7.4.3.2 describe the various functions that can be programmed to the A/B/C/D
switch.
7.4.3.1 Single-Instance Features
Single-instance features can only be assigned to one switch position at a time. If one of these features is
programmed to the A/B/C/D switch, other means of accessing that feature are disabled (i.e., two-position
switch, programmable buttons, call menu, etc.).
Table 7-4: Single-Instance Features
No Function No function programmed to switch.
Talkaround See Section 5.22.
Scan Enables scanning.
Sets transmission power level to High.
• Changing to a Tx Power High position overrides the current personality or user setting
TX Power High
TX Power Low
Keypad Lock Locks DTMF, programmable, and navigation soft keys.
Radio Lock
for TX Power.
• Changing from a Tx Power High position restores the personality-configured Tx Power
Level.
Sets transmission power level to Low.
• Changing to a Tx Power Low position overrides the current personality or user setting
for TX Power.
• Changing from a Tx Power Low position restores the personality-configured Tx Power
Level.
When set, prevents the radio software from responding to the following physical inputs on
the radio:
• Volume Knob Change (power off is not prevented)
• 2-Position Switch
• Channel Knob
• Side User-Programmable Buttons and Keypad (DTMF, programmable, and
navigation/soft keys)
NOTE: Exception is the emergency button and if any key is programmed for Monitor/Clear, it
can be used with the emergency button to clear emergency, if so programmed.
Selects channels 1-16 in position A; 17-32 in position B; 33-48 in position C; and 49-64 in
position D.
Channel Bank
If Channel Bank is selected for any single position, all 4 positions (A, B, C,
and D) will be set to Channel Bank.
83
Page 85
14221-1800-2000, Rev. D
7.4.3.2 Indexed Features
These features can be assigned to any number of positions as long as each index value selected for it is
unique across multiple assignments of the same feature; for example, you cannot assign a Zone with a
particular index (e.g., “ZONE A”) to both positions A and B.
Table 7-5: Indexed Features
FUNCTION DESCRIPTION
Sets to the Zone index value.
•When setting the A/B/C/D switch to an indexed zone assigned position, the radio sets,
but does not “hold,” that zone. This has the resulting effects:
This sets the channel knob to be zone-based system/channel selection just like
selecting a zone from the main “Zone” menu or ramping up/down using the side
Zone Selection
•When changing away from a Zone assigned position, no actions/changes will be taken
Sets to the System index value.
•When setting the A/B/C/D switch to an indexed System assigned position, the radio
System Selection
•When changing away from a System assigned position, no actions/changes will be
user-programmable buttons.
If a user then changes to a different system or zone via another method (menu,
button, etc.), it will override the Zone selection switch setting accordingly and not
require it to remain in the zone where the switch assignment is set.
by the radio.
sets, but does not “hold,” that System. This has the resulting effects:
This sets the channel knob to be system-based channel selection, just like
selecting a system from the main “Zone” menu or ramping up/down using the side
user-programmable buttons.
If a user then changes to a different system or zone via another method (menu,
button, etc.), it will override the System selection switch setting accordingly and not
require it to remain in the system where the switch assignment is set.
taken by the radio.
7.5 PROGRAMMABLE ICONS
7.5.1 Top display
The top display has space for up to seven configurable icons, which can be programmed to display any of
the following:
• Blank
• Signal Strength
• Battery Status
• Bluetooth enabled
• Encryption enabled
• Scan/Vote Scan enabled
• Talkaround enabled
• Emergency mode active
The radio can be programmed to ch ange the color of the top displa y backlight rel ative to the cur rently
selected channel/group. The backlight remains the color programmed for the currently selected
channel/group except during an emergency, in which case the color changes to orange.
84
Page 86
14221-1800-2000, Rev. D
7.5.2 Front display
The front display has space for up to 10 configurable icons, which can be programmed to display
any of the following:
• Blank
• Signal Strength
• Battery Status
• Bluetooth enabled
• Encryption enabled
• Global Encryption
• Talkaround enabled
• TX Disabled
• Tones Disabled
• PTT Disabled
• Speaker Muted
• Monitor
• OTAR Status (Disabled, Registering, Registered, Rekeying)
• TX Power level (Low/High/RX Only)
• GPS Status
• VDOC
• Failsoft
• Data Status (TX/RX)
• Alert(s)
• RX Mail
• Noise Cancellation Enabled
• Type 99 Enabled
• Conventional Site Status (Unregistered/Registered)
85
Page 87
14221-1800-2000, Rev. D
CHANNEL
FREQUENCY
SHIP
(MHZ)
SHORE
(MHZ)
1 1
T: 156.05
R: 160.65
T: 160.65
R: 156.05
International: Public Correspondence, Port Operations
1a
T/R:
156.05
T/R:
156.05
US: Port Operations and Commercial, Vessel Traffic Service (VTS). New
Orleans/Lower Mississippi area.
2 2
T: 156.10
R: 160.70
T: 160.70
R: 156.10
International: Public Correspondence, Port Operations
3 3
T: 156.15
R: 160.75
T: 160.75
R: 156.15
International: Public Correspondence, Port Operations
4
T: 156.20
R: 160.80
T: 160.80
R: 156.20
International: Public Correspondence, Port Operations
4a
T/R:
156.20
T/R:
156.20
Canada: Department Fisheries Ocean (DFO)/Canadian Coast Guard only in
British Columbia coast area. Commercial fishing in east coast area
5
T: 156.25
R: 160.85
T: 160.85
R: 156.25
International: Public Correspondence, Port Operations
5a 5a
T/R:
156.25
T/R:
156.25
US: Port Operations or VTS in Houston, New Orleans and Seattle areas.
6 6 6
T/R:
T/R:
US: Intership Safety
and aircraft.
7
T: 156.35
R: 160.95
T: 160.95
R: 156.35
International: Public Correspondence, Port Operations
7a 7a
T/R:
156.35
T/R:
156.35
US: Commercial
8 8 8
T/R:
T/R:
US: Commercial (Intership only)
Canada: Also assigned for intership in the Lake Winnipeg area.
9 9 9
T/R:
T/R:
US: Boater Calling. Commercial and Non-Commercial.
maritime support operations.
8. REFERENCE
8.1 MARINE FREQUENCIES
Refer to Table 8-1: Marine Frequencies for a list of maritime frequencies per United States Coast Guard
(USCG), National Oceanic and Atmospheric Administration (NOAA), and Canadian Department
Fisheries and Oceans, August 2009:
• United States (US)
• International (Intl)
• Canada (CA)
Table 8-1: Marine Frequencies
US INTL CA
156.30
156.30
CHANNEL USAGE
International: Intership
Canada: May be used for search and rescue communications between ships
156.40
156.45
86
156.40
156.45
International: Intership
International: Intership, Port Operations
Canada: Commercial - British Columbia coast area.
May be used to communicate with aircraft and helicopters in predominantly
US: Environmental (Receive only). Used by Class C Emergency Position-
board communications.
16
16
16
T/R:
T/R:
US: International Distress, Safety and Calling. Ships required to carry radio,
Canada: International Distress, Safety and Calling
17
17
17
T/R:
T/R:
US: State Control
board communications.
18 T: 156.90
R: 161.50
T: 161.50
R: 156.90
International: Public Correspondence, Port Operations
18a 18a
T/R:
156.90
T/R:
156.90
US: Commercial
Canada: Towing - British Columbia coast area.
19 T: 156.95
R: 161.55*
T: 161.55*
R: 156.95
International: Public Correspondence, Port Operations
19a 19a
T/R:
T/R:
US: Commercial
area.
20
20
20
T: 157.00
T: 161.60
US: Port Operations (Duplex)
Canada: Port operations only with 1 watt maximum power.
US INTL CA
156.50
156.55
156.60
156.65
156.70
156.50
156.55
156.60
156.65
156.70
CHANNEL USAGE
International: Intership, Port Operations
Canada: Commercial - British Columbia coast area.
May also be used for communications with aircraft engaged in coordinated
International: Port Operations
Canada: VTS - British Columbia coast area.
International: Port Operations
Canada: VTS - British Columbia coast area.
maintain a listening watch on this channel in US waters.
International: Intership, Port Operations
Canada: VTS - British Columbia coast area.
International: Port Operations
Canada: VTS - British Columbia coast area.
156.75
156.80
156.85
156.95
156.75
156.80
156.85
156.95
Indicating Radio Beacons (EPIRBs).
International: Intership, Port Operations
Canada: Port operations and Ship Movement - British Columbia coast area.
All operations limited to 1-watt maximum power. May also be used for on-
US Coast Guard (USCG), and most coast stations maintain a listening watch
on this channel.
International: International Distress, Safety and Calling
International: Intership, Port Operations
Canada: Port operations and Ship Movement - British Columbia coast area.
All operations limited to 1 watt maximum power. May also be used for on-
Canada: DFO/Canadian Coast Guard. Pacific Pilots - British Columbia coast
R: 161.60
R: 157.00
International: Public Correspondence, Port Operations
87
Page 89
14221-1800-2000, Rev. D
CHANNEL
FREQUENCY
SHIP
(MHZ)
SHORE
(MHZ)
20a
T/R:
157.00
T/R:
157.00
US: Port Operations
21 T: 157.05
R: 161.65*
T: 161.65*
R: 157.05
International: Public Correspondence, Port Operations
21a 21a
T/R:
157.05
T/R:
157.05
US: US Coast Guard only
Canada: DFO/Canadian Coast Guard only.
21b
- -
T/R:
161.65
22 T: 157.10
R: 161.70
T: 161.70
R: 157.10
International: Public Correspondence, Port Operations
22a 22a
T/R:
T/R:
US: Coast Guard Liaison and Maritime Safety Information Broadcasts.
Canadian Coast Guard stations only.
23
23
T: 157.15
R: 161.75
T: 161.75
R: 157.15
International: Public Correspondence, Port Operations
International: Public Correspondence, Port Operations
61 T: 156.075
R: 160.675
T: 160.675
R: 156.075
International: Public Correspondence, Port Operations
61a 61a
T/R:
156.075
T/R:
156.075
Canada: DFO/Canadian Coast Guard only in British Columbia coast area.
62 T: 156.125
R: 160.725
T: 160.725
R: 156.125
International: Public Correspondence, Port Operations
62a
T/R:
156.125
T/R:
156.125
Canada: DFO/Canadian Coast Guard only in British Columbia coast area.
US INTL CA
157.10
157.10
CHANNEL USAGE
Broadcasts announced on channel 16.
Canada: For communications between Canadian Coast Guard and non-
R: 161.85
R: 157.25
International: Public Correspondence, Port Operations
88
Page 90
14221-1800-2000, Rev. D
CHANNEL
FREQUENCY
SHIP
(MHZ)
SHORE
(MHZ)
63 T: 156.175
R: 160.775
T: 160.775
R: 156.175
International: Public Correspondence, Port Operations
63a 63a
T/R:
T/R:
US: Port Operations and Commercial, VTS. New Orleans/Lower Mississippi
Canada: Tow Boats - British Columbia coast area.
64
64
T: 156.225
R: 160.825
T: 160.825
R: 156.225
International: Public Correspondence, Port Operations
64a 64a
T/R:
156.225
T/R:
156.225
Canada: Commercial fishing only.
65 T: 156.275
R: 160.875
T: 160.875
R: 156.225
International: Public Correspondence, Port Operations
65a 65a
T/R:
T/R:
US: Port Operations
Saskatchewan, and Alberta areas.
66 T: 156.325
R: 160.925
T: 160.925
R: 156.325
International: Public Correspondence, Port Operations
66a 66a
T/R:
T/R:
US: Port Operations
area.
67
67
67
T/R:
T/R:
US: Commercial. Used for Bridge-to-bridge communications in lower Miss.
areas. Pleasure craft - British Columbia coast area.
68
68
68
T/R:
T/R:
US: Non-Commercial
Canada: For marinas, yacht clubs and pleasure craft.
69
69
69
T/R:
T/R:
US: Non-Commercial
Pleasure craft - British Columbia coast area.
70
70
70
T/R:
T/R:
US: Digital Selective Calling (voice communications not allowed)
Canada: Digital selective calling for distress, safety and calling
71
71
71
T/R:
T/R:
US: Non-Commercial
clubs - east coast and on Lake Winnipeg.
72
72
72
T/R:
T/R:
US: Non-Commercial (Intership only)
Pleasure craft - British Columbia coast area
US INTL CA
156.175
156.275
156.325
156.175
156.275
156.325
CHANNEL USAGE
area.
Canada: Search and rescue and antipollution operations on the Great Lakes.
Towing on the Pacific Coast. Port operations only in the St. Lawrence River
areas with 1 watt maximum power. Intership in inland Manitoba,
Canada: Port operations only in the St. Lawrence River/Great Lakes areas
with 1 watt maximum power. 1 watt marina channel - British Columbia coast
156.375
156.425
156.475
156.525
156.575
156.625
156.375
156.425
156.475
156.525
156.575
156.625
River. Intership only.
International: Intership, Port Operations
Canada: May also be used for communications with aircraft engaged in
coordinated search and rescue and antipollution operations. Commercial
fishing only in east coast and inland Manitoba, Saskatchewan, and Alberta
International: Port Operations
International: Intership, Port Operations
Canada: Commercial fishing only - east coast area.
International: Digital selective calling for distress, safety and calling
International: Port Operations
Canada: Ship Movement - British Columbia coast area. Marinas and yacht
International: Intership
Canada: May be used to communicate with aircraft and helicopters in
predominantly maritime support operations.
89
Page 91
14221-1800-2000, Rev. D
CHANNEL
FREQUENCY
SHIP
(MHZ)
SHORE
(MHZ)
73
73
73
T/R:
T/R:
US: Port Operations
areas.
74
74
74
T/R:
T/R:
US: Port Operations
Canada: VTS and Ship Movement British Columbia coast area.
75
75
75
T/R:
T/R:
International: Port Operations
1 watt maximum.
76
76
76
T/R:
T/R:
International: Port Operations
1 watt maximum.
77
77
77
T/R:
T/R:
US: Port Operations (Intership only)
in the St. Lawrence River/Great Lakes areas with 1 watt maximum power.
78 T: 156.925
R: 161.525
T: 161.525
R: 156.925
International: Public Correspondence, Port Operations
78a 78a
T/R:
156.925
T/R:
156.925
US: Non-Commercial
Canada: Fishing Industry - British Columbia coast area.
79 T: 156.975
R: 161.575
T: 161.575
R: 156.975
International: Public Correspondence, Port Operations
79a 79a
T/R:
156.975
T/R:
156.975
US: Commercial. Non-Commercial in Great Lakes only
Canada: Fishing Industry - British Columbia coast area.
80 T: 157.025
R: 161.625
T: 161.625
R: 157.025
International: Public Correspondence, Port Operations
80a 80a
T/R:
157.025
T/R:
157.025
US: Commercial. Non-Commercial in Great Lakes only
Canada: Fishing Industry - British Columbia coast area.
81 T: 157.075
R: 161.675
T: 161.675
R: 157.075
International: Public Correspondence, Port Operations
81a 81a
T/R:
157.075
T/R:
157.075
US: US Government only - Environmental protection operations
Canada: DFO/Canadian Coast Guard use only.
82 T: 157.125
R: 161.725
T: 161.725
R: 157.125
International: Public Correspondence, Port Operations
82a 82a
T/R:
157.125
T/R:
157.125
US: US. Government only
Canada: DFO/Canadian Coast Guard use only.
83 T: 157.175
R: 161.775
T: 161.775
R: 157.175
International: Public Correspondence, Port Operations
83a 83a
T/R:
157.175
T/R:
157.175
US: US Coast Guard only
Canada: DFO/Canadian Coast Guard and other Government agencies.
83b
- -
T/R:
161.775
US INTL CA
156.675
156.725
156.775
156.825
156.875
156.675
156.725
156.775
156.825
156.875
CHANNEL USAGE
International: Intership, Port Operations
Canada: May also be used for communications with aircraft engaged in
coordinated search and rescue and antipollution operations. Commercial
fishing only in east coast and inland Manitoba, Saskatchewan, and Alberta
International: Port Operations
Canada: Simplex port operation, ship movement and navigation related
communication only.
Canada: Simplex port operation, ship movement and navigation related
communication only.
International: Intership
Canada: Pilotage - British Columbia coast area; 25 watts. Port operations only
90
Page 92
14221-1800-2000, Rev. D
CHANNEL
FREQUENCY
SHIP
(MHZ)
SHORE
(MHZ)
84
84
84
T: 157.225
R: 161.825
T: 161.825
R: 157.225
US: Public Correspondence (Marine Operator)
International: Public Correspondence, Port Operations
85
85
85
T: 157.275
R: 161.875
T: 161.875
R: 157.275
US: Public Correspondence (Marine Operator)
International: Public Correspondence, Port Operations
86
86
86
T: 157.325
R: 161.925
T: 161.925
R: 157.325
US: Public Correspondence (Marine Operator)
International: Public Correspondence, Port Operations
87
87
87
T: 157.375
T: 161.975
US: Automatic Identification System duplex repeater
Pleasure craft - British Columbia coast area.
87a
T/R:
157.375
T/R:
157.375
US: Public Correspondence (Marine Operator)
87b
T/R:
161.975
T/R:
161.975
Canada: Automatic Ship Identification and Surveillance System.
88
88
T: 157.425
T: 162.025
US: Commercial, Intership only.
Canada: Port operation and ship movement - British Columbia coast area.
International: Port Operations
Canada: Port operation and ship movement - east coast area.
International: Port Operations
8.2 NARROWBANDING
The FCC has mandated that all public safety radios manufactured after January 1, 2013 comply with
narrowbanding restrictions (see http://transition.fcc.gov/pshs/public-safetyspectrum/narrowbanding.html
for more information). Radios manufactured after the above date will comply with these restrictions.
Existing radio personalities that contain frequencies that violate the new FCC rules will cause an invalid
channel error indication on the radio display. The user will need to change the radio personality to comply
with the new rules. Note that there are multiple exceptions to the narrowbanding mandate, including the
Marine Frequencies listed in Section
8.1.
91
Page 93
14221-1800-2000, Rev. D
9. GLOSSARY
-A-
AES Advanced Encryption Standard
AES-256 Advanced Encryption Standard, 256-bit
AMBE+2 Advanced Multi-Band Excitation implementation 2
ANSI American National Standards Institute
ASCII American Standard Code for Information Interchange
-B-
-C-
C Celsius
CA Canada
CDCSS Continuous Digital Coded Squelch System
CH INFO Channel Information
CKR Common Key References
CMB Continuous Marine Broadcast
CTCSS Continuous Tone Coded Squelch System
-D-
DES Digital Encryption Standard
DES-OFB Digital Encryption Standard Output Feedback
DFO Department Fisheries Ocean
DMS Degrees Minutes Seconds
-E-
EPIRB Emergency Position-Indicating Radio Beacons
-F-
F Fahrenheit
FCC Federal Communications Commission
FM Frequency Modulation
-G-
GHz Giga (10
GEOTRANS Geographic Translator
GPS Global Positioning System
Hz Hertz
HKL Harris Key Loader
ID Identification
IEEE Institute of Electrical & Electronics Engineers
INTL International
MHz Megahertz
mm Millimeter
MR Mobile Radio
ms milli (10
-3
) seconds
-N-
NAC Network Access Code
Ni-MH Nickel Metal Hydride
NOAA National Oceanic and Atmospheric Administration
-O-
OET Office of Engineering and Technology
OTAR Over The Air Rekey
-P-
P25 Project 25
POS Position
PRI Priority (Channel)
PTT Push-to-Talk
-Q-
-R-
RF Radio Frequency
RPM2 Radio Personality Manager 2
RSI Radio Set Identifier
RSM Remote Speaker Microphone
RX Receive
-S-
SA Situational Awareness
SMA Subminiature version A
-T-
TIA Telecommunications Industry Association
TX Transmit
93
Page 95
14221-1800-2000, Rev. D
-U-
UHF Ultra High Frequency
UKEK Unique Key Encryption Key
US United States
USCG United States Coast Guard
UTC Universal Tim e Coor d inated
UTM Universal Transverse Mercator
-V-
VDC Volts, Direct Current
VHF Very High Frequency
VIDA Voice Interoperability Data Access
VTS Vessel Traffic Service
-W-
WEEE Waste from Electric and Electronic Equipment
-X-
-Y-
-Z-
94
Page 96
14221-1800-2000, Rev. D
Table 10-1: Displayed Error Messages, Reasons, and Resolutions
Ensure device is discoverable and attempt
arris
Ensure frequency follows band spacing
Ensure frequency follows band spacing
Transfer file again and reattempt install.
Transfer file again and reattempt install.
Attempt install again and contact Harris if
to ensure plan validity.
power cycle and contact
10. BASIC TROUBLESHO OTING
10.1 ERROR MESSAGES
This section provides a list of error messages, as well as possible causes and solutions.
SCREEN/
MENU
Top-Level
Screen
Bluetooth
Pairing
Screen
Channel
Edit
Screen
Install
Operations
Mission Plan
In Progress
Screen
Security
Menu
Utilities
Menu
Channel Info
Screen
DISPLAYED
ERROR MESSAGE
INVALID KEYSTORE
ZEROIZE NEEDED
PAIRING FAILED
EDIT FAILED
INVALID RX FREQUENCY
INVALID TX FREQUENCY
INSTALL FAILED
ZEROIZE FAILED
NO KEYS TO ZEROIZE
INCORRECT PASSWORD
INCORRECT PASSWORD
REASON RESOLUTION
Corrupt key database or
incorrect database
configuration.
Bluetooth pairing failed.
Unable to modify P25
Channel.
Entered Rx frequency is
invalid.
Entered Tx frequency is
invalid.
Error during install process.
Extraction of compressed file
failed.
Removal of existing SW
failed.
Mission plan activation failed.
Radio could not zeroize.
Key database empty. Nothing to zeroize.
Maintenance password
invalid.
Channel edit password
invalid.
Zeroize database.
to re-pair the device.
Power cycle and try again--contact H
if problem persists.
rules.
rules.
Contact Harris if problem persists.
Contact Harris if problem persists.
problem persists.
Use RPM2
Contact Harris if failures persist.
Radio problem—
Harris if problem persists.
Enter valid maintenance password.
Enter valid channel edit password.
95
Page 97
14221-1800-2000, Rev. D
10.2 OTAR ERRORS/I NFO RMATION
WORKAROUNDS:
1. Zeroize.
2. Load proper KEK from the Harris Key Loader or Motorola KVL.
IF RADIO INDICATES:
1. INVALID KEYSTORE ZEROIZE NEEDED - This occurs if the radio’s keys were loaded by the
Harris Key Loader followed by an attempt to load UKEKs with the Key Loader or keys with the
Motorola KVL.
- Fix by performing workaround 1, followed by 2.
2. NO UKEK – Displayed during a zeroize performed from the radio or a zeroize initiated from the
KMF.
- Fix by performing workaround 2.
3. Zeroize Complete – KMF has zeroized the radio.
- Fix by performing workaround 2.
4. Disabled OTAR Icon (red slash) – OTAR is disabled while in scan, talkaround, emergency, and
monitor.
- Fix by disabling these features. Icon will be corrected (no red slash).
5. Gray OTAR Icon (no red slash) – OTAR has not registered with tower (Conventional or Trunked
system).
- Fix by verifying proper frequencies.
- If the radio is turned to the OTAR channel out of range of a conventional tower, and then comes
in range after 3 minutes, fix by issuing an OTAR. Rekey, leaving and re-enter the OTAR channel.
6. Green OTAR Icon – OTAR is registered, all is well.
- If update fails, verify you are in range of the tower and the KEK is correct.
7. Blue OTAR Icon – OTAR is attempting to rekey.
- If rekey fails, verify you are in range of the tower and the KE K is correct.
96
Page 98
14221-1800-2000, Rev. D
11. TECHNICAL ASSIST A NCE
The Technical Assistance Center's (TAC) resources are available to help with overall system operation,
maintenance, upgrades and product support. TAC is the point of contact when answers are needed to
technical questions.
Product specialists, with detailed knowledge of product operation, maintenance and repair provide
technical support via a toll-free (in North America) telephone number. Support is also available through
mail, fax and e-mail.
For more information about technical assistance services, contact your sales representative, or contact the
Technical Assistance Center directly:
North America: 1-800-528-7711
International: 1-434-385-2400
Fax: 1-434-455-6712
E-mail: PSPC_tac@harris.com
12. WARRANTY
Please register this product within 10 days of purchase. Registration validates the warranty coverage, and
enables Harris to contact you in case of any safety notifications issued for this product.
Registration can be made on-line at the Customer Care center webpage:
While on the webpage, please review the applicable battery and/or product warranty literature.
.
97
Page 99
14221-1800-2000, Rev. D
ion, and how to connect devices. If you are unfamiliar with the terms and/or
procedures mentioned in these instructions, please contact your IT department for help
In order for XL-200P radios to be discoverable on the Wi-Fi network, your wireless
mDNS/Multicast.
NOTE
NOTE
APPENDIX A WI-FI PROGRAMMING
These instructions assume the user has a basic familiarity with Wi-Fi Networks, their
configurat
before attempting to configure Wi-Fi programming.
A.1 NETWORK CONFIGURATION
• In order to program t he XL-200P over Wi-Fi, you need to have a wireless network available. This
wireless network will be used by RPM2 and the radio for Wi-Fi functionality. RPM2 and the XL200P come with a default Wi-Fi configuration, but they can be customized to match an existing Wi-Fi
configuration.
• For default operation, setup a wireless network (access point) as follows:
SSID (or networking name) is set to the radio def au lt of “harrisradios”
Password of “password”
Encryption type of either WPA or WPA2
• Ensure your wireless router supports mDNS/Multicast
router must be configured to allow mDNS/Multicast. This varies by router
manufacturer; refer to your router’s documentation for specific settings needed to enable
A.2 RADIO/RPM CO NFIG URATION
Ensure that Enable WIFI is enabled (checked) on the RPM 2 Preferences screen as shown in Figure
12-1. This is disabled (unchecked) by default.
Figure 12-1: Enable WIFI in RPM 2
For def a ul t o p er ation usin g t h e ne t w or k a s described in Secti o n A.1, no other configura t ion of the radio or
RPM is required.
98
Page 100
14221-1800-2000, Rev. D
Radios should start to appear in this area once
network.
Make sure this button is selected to
get into Wi-Fi discovery mode.
A.3 PC CONFIGURATION
Configure the PC to connect to the same Wireless network as the radio. For Windows 7, this can be done
through the Network and Sharing Center.
A.4 CONNECTION
1. For default operation, power on radio while pressing and holding the bottom side and PTT buttons.
This places the radio into Wi-Fi programming mode. A screen appears on the front panel indicating
the radio is in Wi-Fi programming mode.
Figure 12-2: Enable Wi-Fi on XL-200P
2. Start RPM2.
3. Select the Connection tab (the one with the radio icon) and click the Wi-Fi connection button as
shown below. You should see any radios tha t are in Wi-Fi mode appear.
RPM2 and the radio(s) are on the same
99
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.