HARRIS TR 0144 E, TR 0146 E User Manual

14221-1800-2000, Rev. G

MANUAL REVISION HISTORY

REV.

DATE

REASON FOR CHANGE

Sep/15

Initial release.

Sep/15

Added Section 3.

Nov/15

Added CE information.

Jan/16

Updated Declaration of Conformity. Added EU regulatory approval information (standards) and EU RF exposure information.

Jul/16

Updated Table 1-1 and Tableau 2-1. Updated for XLP R2A. Added note to Section 4.3.1 regarding charging the battery before first use. Updated Appendix A. Updated Section 4.3.3.

Jan/17

Updated Sections 1.2, 4.1, 4.6, 5.8, 5.12, 10, included XLP R3A features, and added Sections

4.3.4, 5.35, and 5.6.

Apr/17

Updated to add XLP R4A features.

Jul/17

Added XL-185P, XLP R5A features, and C1D1 information.

ACKNOWLEDGEMENT

This product was developed using GEOTRANS, a product of the National Geospatial Intelligence Agency and U.S. Army Engineering Research and Development Center. Use of this software does not indicate endorsement or approval of the product by the Secretary of Defense or the National Geospatial Intelligence Agency.

This device made under license under one or more of the following US patents: 4,590,473; 4,636,791; 5,148,482; 5,185,796; 5,271,017; 5,377,229; 4,716,407; 4,972,460; 5,502,767; 5,146,697; 5,164,986; 5,185,795.

The Advanced Multi-Band Excitation implementation 2 (AMBE+2) voice coding Technology embodied in this product is protected by intellectual property rights including patent rights, copyrights and trade secrets of Digital Voice Systems, Inc. This voice coding Technology is licensed solely for use within this Communications Equipment. The user of this Technology is explicitly prohibited from attempting to extract, remove, decompile, reverse engineer, or disassemble the Object Code, or in any other way convert the Object Code into a human-readable form. U.S. Patent Nos. #5,870,405, #5,826,222, #5,754,974, #5,701,390, #5,715,365, #5,649,050, #5,630,011, #5,581,656, #5,517,511, #5,491,772, #5,247,579, #5,226,084 and #5,195,166.

CREDITS

Harris, Unity, VIDA, EDACS, NetworkFirst, and OpenSky are registered trademarks of Harris Corporation. TECHNOLOGY TO CONNECT, INFORM AND PROTECT is a trademark of Harris Corporation. Bluetooth is a registered trademark of Bluetooth SIG, Inc. Motorola is a registered trademark of Motorola, Inc. AMBE is a registered trademark and IMBE, AMBE+, and AMBE+2 are trademarks of Digital Voice Systems, Inc. Wi-Fi is a registered trademark of Wi-Fi Alliance. All brand and product names are trademarks, registered trademarks, or service marks of their respective holders.

NOTICE!

The material contained herein is subject to U.S. export approval. No export or re-export is permitted without written approval from the U.S. Government. Rated: EAR99; in accordance with U.S. Dept. of Commerce regulations 15CFR774, Export Administration Regulations. Information and descriptions contained herein are the property of Harris Corporation. Such information and descriptions may not be copied or reproduced by any means, or disseminated or distributed without the express prior written permission of Harris Corporation, PSPC Business, 221 Jefferson Ridge Parkway, Lynchburg, VA 24501. Repairs to this equipment should be made only by an authorized service technician or facility designated by the supplier. Any repairs, alterations or substitutions of recommended parts made by the user to this equipment not approved by the manufacturer could void the user's authority to operate the equipment in addition to the manufacturer's warranty.

This product conforms to the European Union WEEE Directive 2012/19/EU. Do not dispose of this product in a public landfill. Take it to a recycling center at the end of its life.

Harris products comply with the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment (RoHS) Directive.

This manual is published by Harris Corporation without any warranty. Improvements and changes to this manual necessitated by typographical errors, inaccuracies of current information, or improvements to programs and/or equipment, may be made by Harris Corporation at any time and without notice. Such changes will be incorporated into new editions of this manual. No part of this manual may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, for any purpose, without the express written permission of Harris Corporation.

14221-1800-2000, Rev. G

This device is a RF transceiver intended for land mobile radio applications. The device may have use restrictions, which require that the national authority be contacted for any system licensing requirements, frequency use, allowable power level, etc.

14221-1800-2000, Rev. G

DECLARATION OF CONFORMITY

Česky [Czech]

Harris Corporation tímto prohlašuje, že tento XL-200P je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.

Dansk [Danish]

Undertegnede Harris Corporation erklærer herved, at følgende udstyr XL-200P overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.

Deutsch [German]

Hiermit erklärt Harris Corporation, dass sich das Gerät XL-200P in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.

Eesti [Estonian]

Käesolevaga kinnitab Harris Corporation seadme XL-200P vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.

English

Hereby, Harris Corporation, declares that this XL-200P is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

Español [Spanish]

Por medio de la presente Harris Corporation declara que el XL-200P cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.

Ελληνική

[Greek]

ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Harris Corporation ΔΗΛΩΝΕΙ ΟΤΙ XL-200P ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.

Français [French]

Par la présente Harris Corporation déclare que l'appareil XL-200P est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE.

Italiano [Italian]

Con la presente Harris Corporation dichiara che questo XL-200P è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.

Latviski [Latvian]

Ar šo Harris Corporation deklarē, XG 25P UHF-L (378-470 MHz), 7/800 (764-870MHz) atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.

Lietuvių

[Lithuanian]

Šiuo Harris Corporation deklaruoja, kad šis XL-200P atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.

Nederlands [Dutch]

Hierbij verklaart Harris Corporation dat het toestel XL-200P in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.

Malti [Maltese]

Hawnhekk, Harris Corporation, jiddikjara li dan XL-200P jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC.

Magyar [Hungarian]

Alulírott, Harris Corporation nyilatkozom, hogy a XL-200P megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.

Polski [Polish]

Niniejszym Harris Corporation oświadcza, że XL-200P jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.

Português [Portuguese]

Harris Corporation declara que este XL-200P está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE.

Slovensko [Slovenian]

Harris Corporation izjavlja, da je ta XL-200P v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES.

Slovensky [Slovak]

Harris Corporation týmto vyhlasuje, že XL-200P spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES.

Suomi [Finnish]

Harris Corporation vakuuttaa täten että XL-200P tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.

Svenska [Swedish]

Härmed intygar Harris Corporation att denna XL-200P står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.

Íslenska [Icelandic]

Hér með lýsir Harris Corporation yfir því að XL-200P er í samræmi við grunnkröfur og aðrar kröfur, sem gerðar eru í tilskipun 1999/5/EC.

Norsk [Norwegian]

Harris Corporation erklærer herved at utstyret XL-200P er i samsvar med de grunnleggende krav og øvrige relevante krav i direktiv 1999/5/EF.

14221-1800-2000, Rev. G

TABLE OF CONTENTS

Section Page

1. REGULATORY AND SAFETY INFORMATION ........................................................................... 11

1.1 SAFETY CONVENTIONS ........................................................................................................ 11

1.2 SAFETY TRAINING INFORMATION .................................................................................... 11

1.2.1 RF Exposure Guidelines ................................................................................................ 12

1.2.2 Electromagnetic Interference/Compatibility .................................................................. 13

1.3 REGULATORY APPROVALS ................................................................................................. 14

1.3.1 Part 15 ............................................................................................................................ 14

1.3.2 Industry Canada ............................................................................................................. 14

1.4 OPERATING TIPS .................................................................................................................... 14

1.4.1 Efficient Radio Operation .............................................................................................. 14

1.4.2 Antenna Care and Replacement ..................................................................................... 14

1.4.3 Electronic Devices ......................................................................................................... 15

1.4.4 Aircraft ........................................................................................................................... 15

1.4.5 Electric Blasting Caps .................................................................................................... 15

1.4.6 Potentially Explosive Atmospheres ............................................................................... 15

2. RENSEIGNEMENTS SUR LA RÉGLEMENTATION ET SÉCURITÉ ....................................... 16

2.1 CONVENTIONS SUR LES SYMBOLES DE SÉCURITÉ ...................................................... 16

2.2 RENSEIGNEMENTS SUR LA FORMATION SUR LA SÉCURITÉ ...................................... 16

2.2.1 Directives sur l’exposition aux RF ................................................................................ 17

2.2.2 Interférence/Compatibilité Électromagnétique .............................................................. 18

2.3 INTERFÉRENCE DES RADIOFRÉQUENCES ....................................................................... 18

2.3.1 Partie 15 de la FCC ........................................................................................................ 18

2.3.2 Industrie Canada ............................................................................................................ 18

2.4 CONSEILS D’UTILISATION ................................................................................................... 18

2.4.1 Utilisation Efficace de la Radio ..................................................................................... 18

3. HAZARDOUS LOCATIONS .............................................................................................................. 21

3.1 CLASS 1, DIVISION 2 OPTION ............................................................................................... 21

3.2 CLASS 1, DIVISION 1 OPTION ............................................................................................... 22

4. INTRODUCTION ................................................................................................................................ 25

4.1 DESCRIPTION .......................................................................................................................... 25

4.2 STORAGE GUIDELINES ......................................................................................................... 25

4.3 BASIC SETUP ........................................................................................................................... 26

4.3.1 Assemble the Radio ....................................................................................................... 26

4.3.2 Removing the Battery .................................................................................................... 27

4.3.3 Removing the Optional Belt Clip or D-Post .................................................................. 27

4.3.4 Install the SIM Card ....................................................................................................... 28

4.4 UNIVERSAL DEVICE CONNECTOR ..................................................................................... 29

4.5 CLEANING ................................................................................................................................ 29

4.6 OPTIONS AND ACCESSORIES .............................................................................................. 30

4.7 RELATED PUBLICATIONS .................................................................................................... 33

5. BASIC OPERATION ........................................................................................................................... 34

5.1 RADIO CONTROLS .................................................................................................................. 34

5.2 SOFT DTMF KEYPAD ............................................................................................................. 36

5.3 BEFORE FIRST USE ................................................................................................................. 36

5.4 POWER ON AND SET VOLUME ............................................................................................ 37

5.5 RADIO DISPLAYS .................................................................................................................... 37

5.5.1 Top Display ................................................................................................................... 37

14221-1800-2000, Rev. G

TABLE OF CONTENTS

Section Page

5.5.2 Front Display ................................................................................................................. 38

5.6 MANDOWN............................................................................................................................... 40

5.7 STATUS MESSSAGES ............................................................................................................. 40

5.8 PREDEFINED MENU LAYOUTS............................................................................................ 41

5.9 MENU ........................................................................................................................................ 42

5.10 ALERT TONES.......................................................................................................................... 45

5.11 SELECT ZONE/SYSTEM ......................................................................................................... 46

5.12 SELECT GROUP/CHANNEL AND BANK ............................................................................. 47

5.13 LOCK/UNLOCK KEYPAD....................................................................................................... 47

5.14 GROUP CALLS ......................................................................................................................... 48

5.14.1 Transmit a Group Call ................................................................................................... 48

5.14.2 Receive a Group Call ..................................................................................................... 48

5.15 INDIVIDUAL CALLS ............................................................................................................... 49

5.15.1 Transmit an Individual Call ........................................................................................... 49

5.15.2 Receiving an Individual Call ......................................................................................... 49

5.16 USER PROFILES ....................................................................................................................... 50

5.17 NOISE CANCELLATION ......................................................................................................... 51

5.17.1 Enable Noise Cancellation ............................................................................................. 51

5.17.2 Using Noise Cancellation .............................................................................................. 52

5.17.3 The Effect of Distance from the Microphone ................................................................ 52

5.17.4 Primary versus Secondary Microphone ......................................................................... 52

5.17.5 When using an SCBA Mask .......................................................................................... 52

5.18 PTT OPTIONS ........................................................................................................................... 53

5.19 VOICE ANNUNCIATION ........................................................................................................ 53

5.20 ENABLE/DISABLE ENCRYPTION ........................................................................................ 54

5.21 TRANSMIT ENABLE/DISABLE ............................................................................................. 54

5.22 CHANNEL GUARD (ANALOG CONVENTIONAL ONLY) ................................................. 55

5.23 USE TALKAROUND TO BYPASS REPEATER (ANALOG AND P25 CONVENTIONAL

ONLY) ........................................................................................................................................ 56

5.24 TYPE 99 OPERATION .............................................................................................................. 57

5.24.1 Enable/Disable Type 99 ................................................................................................. 57

5.24.2 Disable After PTT.......................................................................................................... 58

5.24.3 Auto Reset ..................................................................................................................... 58

5.25 CALL ALERT (PAGE) .............................................................................................................. 58

5.25.1 Send Alert ...................................................................................................................... 58

5.25.2 Receive Alert ................................................................................................................. 58

5.26 DTMF ......................................................................................................................................... 58

5.27 AUDIO PLAYBACK ................................................................................................................. 59

5.28 START SCAN ............................................................................................................................ 60

5.29 STOP SCAN ............................................................................................................................... 61

5.30 MONITOR AND SQUELCH TYPES (CONVENTIONAL ONLY) ........................................ 62

5.31 NUISANCE DELETE ................................................................................................................ 63

5.32 CONVENTIONAL FAILSOFT (EDACS ONLY) .................................................................... 64

5.33 EMERGENCY OPERATION .................................................................................................... 65

5.33.1 Declaring an Emergency Call ........................................................................................ 65

5.33.2 Receiving an Emergency Call ....................................................................................... 65

5.33.3 Stealth Emergency ......................................................................................................... 66

5.34 MDC-1200 (ANALOG CONVENTIONAL ONLY) ................................................................. 66

14221-1800-2000, Rev. G

TABLE OF CONTENTS

Section Page

5.34.1 Normal PTT Operation .................................................................................................. 66

5.34.2 MDC PTT ID Receive Handling ................................................................................... 66

5.34.3 Emergency Declaration ................................................................................................. 66

5.35 BEON OPERATION .................................................................................................................. 67

6. ADVANCED OPERATIONS .............................................................................................................. 68

6.1 VIEW/CHANGE PERSONALITIES ......................................................................................... 68

6.1.1 View Personalities ......................................................................................................... 68

6.1.2 Change Active Personality ............................................................................................ 69

6.2 SITUATIONAL AWARENESS (SA) – P25 CONVENTIONAL ONLY ................................. 70

6.3 USER-DEFINED ZONES/SYSTEMS ....................................................................................... 71

6.3.1 Command Tactical Zone ................................................................................................ 71

6.3.2 Mixed System Zone ....................................................................................................... 72

6.4 CH INFO MENU ........................................................................................................................ 73

6.5 AUDIO SETTINGS .................................................................................................................... 73

6.6 DISPLAY SETTINGS ................................................................................................................ 74

6.7 GPS SETTINGS ......................................................................................................................... 75

6.8 POSITION INFO ........................................................................................................................ 75

6.9 WI-FI .......................................................................................................................................... 76

6.10 BLUETOOTH ............................................................................................................................ 77

6.10.1 Enable Bluetooth ........................................................................................................... 77

6.10.2 Pair Devices ................................................................................................................... 78

6.11 CLOCK SETTINGS ................................................................................................................... 79

6.12 BATTERY INFO ........................................................................................................................ 79

6.13 SELECT LANGUAGE............................................................................................................... 80

6.14 SET UP SCAN ........................................................................................................................... 80

6.14.1 Default, Priority 1, and Priority 2 Channels .................................................................. 81

6.14.2 Trunked/Conventional Scanning ................................................................................... 81

6.14.3 Vote Scan (Analog and P25 Conventional Only) .......................................................... 82

6.14.4 Edit Scan List ................................................................................................................. 82

6.14.5 Set or Remove Priority 1 and Priority 2 Channels ......................................................... 83

6.14.6 Custom Scan Lists ......................................................................................................... 84

6.14.7 Wide Area System Scan (P25 Trunked and EDACS) ................................................... 86

6.15 RADIO STATUS ........................................................................................................................ 86

6.16 RADIO MESSAGE .................................................................................................................... 87

6.17 RADIO TEXTLINK ................................................................................................................... 87

6.17.1 Radio TextLink Messages ............................................................................................. 88

6.17.2 Radio TextLink Forms ................................................................................................... 88

6.17.3 View Received Messages .............................................................................................. 89

6.18 FAULTS/ALERTS ..................................................................................................................... 89

6.19 TONE ENCODE ........................................................................................................................ 90

6.20 ENCRYPTION ........................................................................................................................... 90

6.20.1 Create and Load Keys .................................................................................................... 90

6.20.2 Zeroize Keys from Radio ............................................................................................... 91

6.20.3 Protected Keys ............................................................................................................... 91

6.20.4 Global Encryption .......................................................................................................... 91

6.20.5 Select Keyset ................................................................................................................. 92

6.20.6 View Key List ................................................................................................................ 92

6.20.7 Delete Individual Keys .................................................................................................. 93

14221-1800-2000, Rev. G

TABLE OF CONTENTS

Section Page

6.20.8 OTAR Configuration ..................................................................................................... 94

6.21 SITE ALIAS AND SITE LOCK (P25 TRUNKED ONLY) ...................................................... 94

7. PROGRAMMING ................................................................................................................................ 95

7.1 PROGRAMMING VIA RPM2 .................................................................................................. 95

7.2 EDIT CHANNEL (ANALOG AND P25 CONVENTIONAL ONLY) ..................................... 95

7.3 OTAP .......................................................................................................................................... 97

7.4 PROGRAMMABLE BUTTONS AND SWITCHES ................................................................. 97

7.4.1 Programmable Buttons .................................................................................................. 97

7.4.2 Programmable A/B (Ø/O) Switch ................................................................................. 99

7.4.3 Programmable A/B/C/D Switch .................................................................................... 99

7.5 PROGRAMMABLE ICONS .................................................................................................... 100

7.5.1 Top display .................................................................................................................. 100

7.5.2 Front display ................................................................................................................ 101

8. REFERENCE ...................................................................................................................................... 103

8.1 MARINE FREQUENCIES ...................................................................................................... 103

8.2 NARROWBANDING .............................................................................................................. 108

9. GLOSSARY ........................................................................................................................................ 109

10. BASIC TROUBLESHOOTING ........................................................................................................ 112

10.1 ERROR MESSAGES ............................................................................................................... 112

10.2 OTAR ERRORS/INFORMATION .......................................................................................... 113

11. TECHNICAL ASSISTANCE ............................................................................................................ 114

12. WARRANTY ...................................................................................................................................... 114

APPENDIX A WI-FI PROGRAMMING ......................................................................................... 115

LIST OF FIGURES

Page

Figure 4-1: Radio Assembly .......................................................................................................................... 26

Figure 4-2: Remove the Battery ..................................................................................................................... 27

Figure 4-3: Remove Belt Clip ........................................................................................................................ 27

Figure 4-4: SIM Card Installation .................................................................................................................. 28

Figure 4-5: Universal Device Connector ....................................................................................................... 29

Figure 5-1: Radio Controls ............................................................................................................................ 34

Figure 5-2: Using the Soft DTMF Keypad .................................................................................................... 36

Figure 5-3: Top Display ................................................................................................................................. 37

Figure 5-4: Sample Idle Front Display .......................................................................................................... 38

Figure 5-5: Using Noise Cancellation ............................................................................................................ 52

Figure 6-1: Enabling Wi-Fi ............................................................................................................................ 76

Figure 6-2: Wi-Fi Install Active ..................................................................................................................... 77

Figure A-1: Options  Network Configuration .......................................................................................... 116

Figure A-2: Wi-Fi Configuration ................................................................................................................. 116

Figure A-3: Service Name ........................................................................................................................... 117

Figure A-4: Enable Wi-Fi in RPM2 ............................................................................................................. 117

Figure A-5: Enable Wi-Fi Programming Mode on Radio ........................................................................... 118

Figure A-6: RPM2 Radio Tab: Wi-Fi .......................................................................................................... 119

14221-1800-2000, Rev. G

LIST OF TABLES

Page

Table 1-1: RF Exposure Compliance Tested Distances (Worst Case Scenario) ............................................ 12

Table 1-2: Simultaneous Transmission Scenarios ......................................................................................... 13

Tableau 2-1 : Distances de test de conformité des expositions aux RF (pire des scénarios) ......................... 17

Table 4-1: Options and Accessories ............................................................................................................... 30

Table 5-1: Radio Controls, Indicators, and Connectors ................................................................................. 34

Table 5-2: Radio Icons ................................................................................................................................... 38

Table 5-3: Status Messages ............................................................................................................................ 40

Table 5-4: Predefined Menu Layouts ............................................................................................................. 41

Table 5-5: Menu Navigation ......................................................................................................................... 42

Table 5-6: Alert Tones ................................................................................................................................... 45

Table 7-1: Valid Frequency Ranges ............................................................................................................... 97

Table 7-2: Programmable Button Options ..................................................................................................... 98

Table 7-3: Programmable Ø/O Switch Options ............................................................................................. 99

Table 7-4: Single-Instance Features ............................................................................................................... 99

Table 7-5: Indexed Features ......................................................................................................................... 100

Table 8-1: Marine Frequencies .................................................................................................................... 103

Table 10-1: Displayed Error Messages, Reasons, and Resolutions ............................................................ 112

Table 12-1: Wi-Fi Feature Support .............................................................................................................. 119

Harris Corporation, Public Safety and Professional Communications (PSPC) Business continually evaluates its technical publications for completeness, technical accuracy, and organization. You can assist in this process by submitting your comments and suggestions to the following: Harris Corporation fax your comments to: 1-434-455-6851 PSPC Business or

Technical Publications e-mail us at: PSPC_TechPubs@harris.com 221 Jefferson Ridge Parkway Lynchburg, VA 24501

14221-1800-2000, Rev. G

1. REGULATORY AND SAFETY INFORMATION

1.1 SAFETY CONVENTIONS

The following conventions are used throughout this manual to alert the user to general safety precautions that must be observed during all phases of operation, service, and repair of this product. Failure to comply with these precautions or with specific warning elsewhere in this manual violates safety standards of design, manufacture, and intended use of the product. Harris assumes no liability for the customer’s failure to comply with these standards.

The WARNING symbol calls attention to a procedure, practice, or the like, which, if not correctly performed or adhered to, could result in personal injury. Do not proceed beyond a WARNING symbol until the conditions identified are fully understood or met.

The CAUTION symbol calls attention to an operating procedure, practice, or the like, which, if not performed correctly or adhered to, could result in damage to the equipment or severely degrade the equipment performance.

The NOTE symbol calls attention to supplemental information, which may improve system performance or clarify a process or procedure.

1.2 SAFETY TRAINING INFORMATION

The Harris XL-200P/XL-185P portable radio generates RF electromagnetic energy

during transmit mode. This radio is designed for and classified as “Occupational Use Only,” meaning it must be used only during the course of employment by

individuals aware of the hazards and the ways to minimize such hazards. This

radio is NOT intended for use by the “General Population” in an uncontrolled

environment.

The XL-200P/XL-185P portable radio has been tested and complies with the FCC RF exposure limits for “Occupational Use Only.” In addition, this Harris radio complies with the following Standards and Guidelines with regard to RF energy and electromagnetic energy levels and evaluation of such levels for exposure to humans:

• FCC KDB Publication 447498 General RF Exposure Guidance

• American National Standards Institute (C95.1 – 1992

), IEEE Standard for Safety Levels with

Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz.

• American National Standards Institute (C95.3 – 1992), IEEE Recommended Practice for the

Measurement of Potentially Hazardous Electromagnetic Fields – RF and Microwave.

• IC Standard RSS-102. Radiofrequency Exposure Compliance of Radiocommunication Apparatus

(All Frequency Bands).

• European Council Directive 89/391/EEC.

Tested to ANSI C95.1-1992 in compliance with 47 CFR 2.1093. Meets or exceeds safety requirements of ANSI C95.1-2005.

WARNING

CAUTION

NOTE

WARNING

14221-1800-2000, Rev. G

1.2.1 RF Exposure Guidelines

To ensure that exposure to RF electromagnetic energy is within the EU/AU/FCC/IC allowable limits for occupational use, always adhere to the following guidelines:

• DO NOT operate the radio without a proper antenna attached, as this may damage the radio and may

also cause the FCC RF exposure limits to be exceeded. A proper antenna is the antenna supplied with this radio by Harris or an antenna specifically authorized by Harris for use with this radio. (Refer to Table 4-1.)

• DO NOT transmit for more than 50% of total radio use time (“50% duty cycle”). Transmitting more

than 50% of the time can cause FCC RF exposure compliance requirements to be exceeded. The radio is transmitting when the “TX” indicator appears in the display. The radio will transmit by pressing the “PTT” (Push-To-Talk) button.

• ALWAYS transmit using low power when possible. In addition to conserving battery charge, low

power can reduce RF exposure.

• ALWAYS use Harris authorized accessories (antennas, batteries, belt clips, speaker/mics, etc.). Use

of unauthorized accessories may cause the FCC Occupational/Controlled Exposure RF compliance requirements to be exceeded. (Refer to Table 1-1.)

• As noted in Table 1-1, ALWAYS keep the housing of the transmitter AT LEAST 0.47 inches (1.2

cm) from the body and at least 0.98 in (2.5 cm) from the face when transmitting to ensure EU/AU/FCC/IC RF exposure compliance requirements are not exceeded. However, to provide the best sound quality to the recipients of your transmission, Harris recommends you hold the microphone at least 2 in (5 cm) from mouth, and slightly off to one side.

• Refer to Standard EN 62311:2008.

Table 1-1: RF Exposure Compliance Tested Distances (Worst Case Scenario)

RADIO FREQUENCY

Body2

Face

VHF

(136 - 174 MHz)

0.47 in (1.2 cm)

0.98 in (2.5 cm)

UHF

(378 - 522 MHz)

0.47 in (1.2 cm)

0.98 in (2.5 cm)

700/800 MHz (768 - 776 MHz) (798 - 806 MHz) (806 - 824 MHz) (851 - 870 MHz)

0.47 in (1.2 cm)

0.98 in (2.5 cm)

900 MHz (935-944 MHz) (896-902 MHz)

0.47 in (1.2 cm)

0.98 in (2.5 cm)

2400 MHz

(2412 - 2472 MHz)

0.47 in (1.2 cm)

0.98 in (2.5 cm)

5 GHz

(5.18 - 5.825 GHz)

0.47 in (1.2 cm)

0.98 in (2.5 cm)

This is worst case based on the thinnest body mount accessory (belt clip).

CAUTION

14221-1800-2000, Rev. G

SAR Evaluation: 1g averaged, 50% PTT Duty Factor, Occupational/Controlled Exposure.

This device contains multiple transmitters that may operate simultaneously, see Table 1-2 Simultaneous Transmission Scenarios for the capable transmit configurations.

Table 1-2: Simultaneous Transmission Scenarios

NO.

CAPABLE TRANSMIT CONFIGURATION

HEAD

BODY-WORN ACCESSORY

LTE B13/14/4 + VHF

YES

LTE B13/14/4 + UHF

YES

LTE B14 + 800 MHz

YES

LTE B13/14/4 + Bluetooth

YES

LTE B13/14/4 + 2.4 GHz WLAN

YES

LTE B13/14/4 + 5 GHz WLAN

YES

LTE B13/14/4 + VHF + Bluetooth

YES

LTE B13/14/4 + UHF + Bluetooth

YES

LTE B14 + 800 MHz + Bluetooth

YES

LTE B13/14/4 + VHF + WLAN

YES

LTE B13/14/4 + UHF + WLAN

YES

LTE B14 + 800 MHz + WLAN

YES

LTE B13/14/4 + 900 MHz (XL-185P Only)

YES

LTE B13/14/4 + 900 MHz + Bluetooth

YES

LTE B13/14/4 + 900 MHz + WLAN

YES

LTE B13/14/4 + 700 MHz simultaneous transmission is not supported by this device. LTE B13/4 + 800 MHz simultaneous transmission is not supported by

LTE is not supported by the XL Portable with the C1D1 option.

The information in this section provides the information needed to make the user aware of RF exposure, and what to do to assure that this radio operates within the FCC RF exposure limits.

1.2.2 Electromagnetic Interference/Compatibility

During transmissions, this Harris radio generates RF energy that can possibly cause interference with other devices or systems. To avoid such interference, turn off the radio in areas where signs are posted to do so. DO NOT operate the transmitter in areas that are sensitive to electromagnetic radiation such as hospitals, aircraft, and blasting sites.

NOTE

14221-1800-2000, Rev. G

1.3 REGULATORY APPROVALS

Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.

1.3.1 Part 15

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause undesired

operation.

1.3.2 Industry Canada

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

1.4 OPERATING TIPS

Antenna location and condition are important when operating a portable radio. Operating the radio in low-lying areas or terrain, under power lines or bridges, inside of a vehicle, or in a metal framed building can severely reduce the range of the unit. Mountains can also reduce the range of the unit.

In areas where transmission or reception is poor, some improvement may be obtained by ensuring that the antenna is vertical. Moving a few yards in another direction or moving to a higher elevation may also improve communications. Vehicular operation can be aided with the use of an externally mounted antenna.

Battery condition is another important factor in the trouble-free operation of a portable radio. Always properly charge the battery.

1.4.1 Efficient Radio Operation

Keep the antenna in a vertical position when receiving or transmitting a message.

Do NOT hold onto the antenna when the radio is powered on!

1.4.2 Antenna Care and Replacement

Do not use the portable radio with a damaged or missing antenna. A minor burn may result if a damaged antenna comes into contact with the skin. Replace a damaged antenna immediately. Operating a portable radio with the antenna missing could cause personal injury, damage the radio, and may violate FCC regulations.

WARNING

14221-1800-2000, Rev. G

Use only the supplied or approved antenna. Unauthorized antennas, modifications, or attachments could cause damage to the radio unit and may violate FCC regulations. (Refer to Table 4-1.)

1.4.3 Electronic Devices

RF energy from portable radios may affect some electronic equipment. Most modern electronic equipment in cars, hospitals, homes, etc. is shielded from RF energy. However, in areas in which you are instructed to turn off two-way radio equipment, always observe the rules. If in doubt, turn it off!

1.4.4 Aircraft

• Always turn off a portable radio before boarding any aircraft!

• Use it on the ground only with crew permission.

• DO NOT use while in-flight!!

1.4.5 Electric Blasting Caps

To prevent accidental detonation of electric blasting caps, DO NOT use two-way radios within 1000 feet of blasting operations. Always obey the "Turn Off Two-Way Radios" signs posted where electric blasting caps are being used (OSHA Standard:

1926.900).

1.4.6 Potentially Explosive Atmospheres

Areas with potentially explosive atmospheres are often, but not always, clearly marked. These may be fueling areas, such as gas stations, fuel or chemical transfer or storage facilities, and areas where the air contains chemicals or particles, such as grain, dust, or metal powders.

Sparks in such areas could cause an explosion or fire resulting in bodily injury or even death.

Turn off two-way radios when in any area with a potentially explosive atmosphere. It is rare, but not impossible that a radio or its accessories could generate sparks.

CAUTION

WARNING

14221-1800-2000, Rev. G

2. RENSEIGNEMENTS SUR LA RÉGLEMENTATION ET SÉCURITÉ

2.1 CONVENTIONS SUR LES SYMBOLES DE SÉCURITÉ

Les conventions suivantes sont utilisées dans le présent manuel pour avertir l’utilisateur des précautions générales de sécurité qui doivent être observées pendant toutes les phases d’opération, d’entretien et de réparation de ce produit. Le non-respect de ces précautions ou d’avertissements précisés ailleurs enfreint les normes de sécurité de la conception, de la fabrication et de l’utilisation prévue du produit. Harris n’assume aucune responsabilité pour le

non-respect de ces normes par le client.

Le symbole MISE EN GARDE attire l’attention sur une procédure ou une pratique qui, si elle n’est pas correctement effectuée ou observée, pourrait

entraîner une blessure personnelle. Ne pas poursuivre au-delà d’un symbole de MISE EN GARDE avant que les conditions identifiées soient complètement comprises ou satisfaites.

Le symbole AVERTISSEMENT attire l’attention sur une procédure ou une pratique opérationnelle qui, si elle n’est pas correctement effectuée ou observée, pourrait entraîner un bris d’équipement ou une importante baisse de rendement de l’équipement.

Le symbole REMARQUE attire l’attention sur des renseignements supplémentaires qui peuvent améliorer le rendement du système ou clarifier un processus ou une procédure.

2.2 RENSEIGNEMENTS SUR LA FORMATION SUR LA SÉCURITÉ

La radio portative Harris XL-200P/XL-185P produit de l’énergie électromagnétique des RF lorsqu’en mode de transmission. Cette radio est conçue et classée pour une « Utilisation professionnelle seulement », ce qui signifie qu’elle ne doit être utilisée que dans le cadre d’un emploi par des individus conscients des

risques et des moyens de limiter ceux-ci. Cette radio N’EST PAS conçue pour une utilisation par la « Population générale » dans un environnement non contrôlé.

La radio portative XL-200P/XL-185P a été testée et est conforme aux limites d’exposition aux RF de la FCC pour une « Utilisation professionnelle seulement ». De plus, cette radio Harris est conforme aux normes et directives suivantes quant à l’énergie des RF et aux niveaux d’énergie électromagnétique, ainsi qu’à l’évaluation de ces niveaux pour l’exposition aux humains:

• FCC KDB 447498

• American National Standards Institute (C95.1 – 1992), norme de l’IEEE sur les niveaux sécuritaires

d’exposition humaine aux champs électromagnétiques des radiofréquences, 3 kHz à 300 GHz.

• American National Standards Institute (C95.3 – 1992), pratique recommandée par l’IEEE pour la

mesure des champs électromagnétiques potentiellement dangereux – RF et micro-ondes.

MISE EN GARDE

AVERTISSEMENT

REMARQUE

MISE EN GARDE

14221-1800-2000, Rev. G

2.2.1 Directives sur l’exposition aux RF

Pour s’assurer que l’exposition à l’énergie électromagnétique des RF se situe dans les limites acceptables de la FCC pour l’utilisation professionnelle, respectez toujours les directives suivantes :

• N’utilisez PAS la radio sans qu’une antenne appropriée y soit connectée, car ceci peut endommager la

radio et également causer un dépassement des limites d’exposition aux RF de la FCC. Une antenne appropriée est celle fournie par Harris avec cette radio, ou une antenne spécifiquement autorisée par Harris pour être utilisée avec cette radio. (Reportez-vous à Tableau 2-1.)

• Ne transmettez PAS pendant plus de 50 % de la durée d’utilisation totale de la radio (« cycle de

service de 50 % »). La transmission pendant plus de 50 % du temps peut causer un dépassement des exigences de conformité de la FCC en matière d’exposition aux RF. La radio transmet lorsque l’indicateur « TX » apparaît sur l’affichage. La radio transmet lorsqu’on appuie sur le bouton « PTT » (bouton de microphone).

• Transmettez TOUJOURS en basse puissance lorsque possible. En plus de préserver la charge de la

pile, une faible puissance réduit l’exposition aux RF.

• Utilisez TOUJOURS des accessoires autorisés Harris (antennes, piles, pinces de ceinture, haut-

parleurs/micros, etc.). L’utilisation d’accessoires non autorisés peut entraîner un dépassement des exigences de conformité pour une exposition aux RF professionnelle ou contrôlée de la FCC. (Reportez-vous à Table 4-1.)

• Tel qu’indiqué dans Tableau 2-1, conservez TOUJOURS l’appareil et son antenne à AU MOINS

1,2 cm du corps, et à au moins 2,5 cm du visage pendant la transmission, pour vous assurer de ne pas dépasser les exigences de conformité de la FCC en matière d’exposition aux RF. Cependant, pour offrir la meilleure qualité sonore aux auditeurs de votre transmission, Harris recommande de tenir le microphone à au moins 5 cm (2 po) de votre bouche et légèrement déplacé sur un côté.

Tableau 2-1 : Distances de test de conformité des expositions aux RF (pire des scénarios)

RADIOFRÉQUENCES

Corps3

Visage

VHF

(136 - 174 MHz)

1,2 cm

2,5 cm

UHF

(378 - 522 MHz)

1,2 cm

2,5 cm

700/800 MHz (768 - 776 MHz) (798 - 806 MHz) (806 - 824 MHz) (851 - 870 MHz)

1,2 cm

2,5 cm

900 MHz (935-944 MHz) (896-902 MHz)

1,2 cm

2,5 cm

2400 MHz

(2412 - 2472 MHz)

1,2 cm

2,5 cm

Ce est le pire des cas basée sur le corps plus mince monter accessoire (clip ceinture).

AVERTISSEMENT

14221-1800-2000, Rev. G

RADIOFRÉQUENCES

Corps3

Visage

5 GHz

(5.18 - 5.825 GHz)

1,2 cm

2,5 cm

Dans cette section figurent les renseignements nécessaires pour sensibiliser l’utilisateur à l’exposition aux RF et sur ce qu’il faut faire pour s’assurer que cette radio fonctionne dans les limites d’exposition aux RF de la FCC.

2.2.2 Interférence/Compatibilité Électromagnétique

Pendant les transmissions, cette radio Harris produit de l’énergie des RF qui peut causer de l’interférence avec d’autres appareils ou systèmes. Pour éviter de telles interférences, fermez la radio dans les zones où il est indiqué de le faire. N’utilisez PAS le transmetteur dans des zones sensibles aux radiations électromagnétiques, comme les hôpitaux, les avions et les sites de détonation.

2.3 INTERFÉRENCE DES RADIOFRÉQUENCES

2.3.1 Partie 15 de la FCC

Cet appareil est conforme à la Partie 15 de la réglementation de la FCC. Le fonctionnement est soumis aux deux conditions suivantes :

1. Cet appareil ne doit pas causer une interférence nuisible; et

2. Cet appareil doit accepter toute interférence reçue, y compris une interférence qui peut causer un

fonctionnement non souhaité.

2.3.2 Industrie Canada

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

2.4 CONSEILS D’UTILISATION

L’emplacement et l’état de l’antenne sont importants pour l’utilisation d’une radio portative. L’utilisation de la radio dans des zones de faible élévation, sous des lignes électriques ou des ponts, à l’intérieur d’un véhicule ou dans un immeuble à ossature métallique, peut réduire la portée de l’appareil de manière considérable. Les montagnes peuvent également réduire la portée de l’unité.

Dans les zones où la transmission ou la réception est insatisfaisante, certaines améliorations peuvent être obtenues en s’assurant que l’antenne est verticale. Se déplacer de quelques mètres dans une autre direction ou à un emplacement plus élevé peut également améliorer les communications. L’utilisation d’une antenne fixée à l’extérieur peut faciliter le fonctionnement dans un véhicule.

L’état de la pile est un autre facteur important d’une utilisation sans tracas d’une radio portative. Chargez toujours correctement la pile.

2.4.1 Utilisation Efficace de la Radio

Gardez l’antenne dans une position verticale pendant la réception ou la transmission d’un message.

14221-1800-2000, Rev. G

Ne tenez PAS l’antenne lorsque la radio est allumée!

2.4.1.1 Entretien Et Remplacement De L’antenne

N’utilisez pas la radio portative si son antenne est endommagée ou absente. Une brûlure légère peut se produire au contact d’une antenne endommagée avec la peau. Remplacez immédiatement une antenne endommagée. L’utilisation d’une radio portative alors que l’antenne est absente peut causer des blessures,

endommager la radio et pourrait enfreindre la réglementation de la FCC.

Utilisez seulement l’antenne fournie ou une antenne approuvée. Des antennes non autorisées, des modifications ou des ajouts à une antenne peuvent endommager la radio et enfreindre la réglementation de la FCC. (Reportez-vous à Table 4-1.)

2.4.1.2 Appareils Électroniques

L’énergie des RF provenant de radios portatives peut affecter certains appareils électroniques. La majorité de l’équipement électronique moderne dans les voitures, les hôpitaux, les maisons, etc. est blindé contre l’énergie des RF. Cependant, dans les zones où l’on vous demande de fermer l’équipement de radio bidirectionnelle, respectez toujours

les règles. En cas de doute, éteignez-le!

2.4.1.3 Avion

• Éteignez toujours une radio portative avant d’embarquer à bord d’un avion!

• Ne l’utilisez au sol qu’avec la permission de l’équipage.

• NE l’utilisez PAS durant le vol!

2.4.1.4 Détonateurs Électriques

Pour prévenir la détonation accidentelle des détonateurs électriques, n’utilisez PAS

de radios bidirectionnelles à moins de 305 m (1 000 pi) des opérations de détonation. Respectez toujours les indications « Éteindre les radios bidirectionnelles » situées là où des détonateurs électriques sont utilisés. (Norme OSHA : 1926.900)

MISE EN GARDE

AVERTISSEMENT

MISE EN GARDE

14221-1800-2000, Rev. G

2.4.1.5 Atmosphère Potentiellement Explosive

Les zones ayant une atmosphère potentiellement explosive sont souvent, mais pas

toujours, identifiées clairement comme telles. Il peut s’agir de zones d’alimentation en carburant, comme les postes d’essence, les installations de stockage ou de transfert de carburant ou de produits chimiques, ainsi que les zones dont l’air

contient des produits chimiques ou des particules, comme des grains, de la poussière ou des poudres métalliques.

Des étincelles dans de telles zones peuvent provoquer une explosion ou un incendie, causant ainsi des blessures ou même la mort.

Éteignez les radios bidirectionnelles dans toute zone ayant une atmosphère potentiellement explosive. Il est rare, mais pas impossible qu’une radio ou ses accessoires produisent des étincelles.

MISE EN GARDE

14221-1800-2000, Rev. G

3. HAZARDOUS LOCATIONS

3.1 CLASS 1, DIVISION 2 OPTION

Radios ordered with the Class 1, Division 2 option are suitable for use in Class 1, Division 2, Groups A, B, C, and D or non-hazardous (unclassified) locations only.

Les radios commandées avec l’option Classe 1, Division 2 sont adéquates pour utilisation en Classe 1,

Division 2, Groupes A, B, C et D, ou en lieux non-hasardeux (non-classifiés) seulement

EXPLOSION HAZARD – REPLACE BATTERY PACK ONLY IN AN AREA KNOWN TO BE NON-HAZARDOUS, AND ONLY WITH HARRIS PART NO. 14035-4010-01.

AVERTISSEMENT – RISQUE D’EXPLOSION – LES BATTERIES DOIVENT ÊTRE REMPLACÉES DANS UNE ZONE RECONNUE NON-HASARDEUSE SEULEMENT, ET SEULEMENT AVEC UNE BATTERIE HARRIS PORTANT LE NUMÉRO DE PIÈCE 14035-4010-01.

EXPLOSION HAZARD – Substitution of any component may impair suitability for Class I, Division 2.

AVERTISSEMENT – RISQUE D’EXPLOSION – Une substitution de toute composante pourrait compromettre la convenance pour la Classe I, Division 2.

EXPLOSION HAZARD – Do not exceed maximum battery charging current of

5.250 A or maximum charging voltage of 12.0 V DC at any time.

CAUTION - The battery used in this device may present a risk of fire or explosion when heated above 100°C (212°F) or incinerated. Replace battery with Harris Part No. 14035-4010-01 only. Use of another battery may present a risk of fire or explosion.

Battery replacement instructions: Remove battery by 1) depressing battery latches then 2) remove battery from radio chassis. Install replacement battery by inserting battery in radio chassis opening and depressing battery into chassis until both battery latches are engaged. Dispose of used battery promptly. Keep away from children. Do not disassemble and do not dispose of in fire.

EXPLOSION HAZARD – In addition to any simple single-ended coil antenna and carrying case option, only the following Harris accessories may be used with this radio:

PART NUMBER

DESCRIPTION

12082-0600-01

Speaker Microphone

12082-0600-02

Speaker Microphone, Emergency Button

12082-0650-01

Microphone, Palm,2 Wire, Black

12082-0650-02

Microphone, Palm, 2 Wire, Beige

12082-0650-03

Microphone, Mini-Lapel,3 Wire, Black

12082-0650-04

Microphone, Mini-Lapel,3 Wire, Beige

12082-0650-05

Earphone Kit, Black

12082-0650-06

Earphone Kit, Beige

WARNING

14221-1800-2000, Rev. G

PART NUMBER

DESCRIPTION

12082-0650-07

Headset, In-Ear, Boom Mic, In-Line PTT

12082-0650-08

Headset, Lightweight, Over-the-Head, Single Ear, In-Line PTT

12082-0650-09

Headset, Lightweight, Behind-the-Head, Dual Ear, In-Line PTT

12082-0650-10

Headset, Lightweight, Behind-the-Head, Dual Ear, Pigtail PTT

12082-0650-13

Headset, Heavy Duty, Behind-the-Head, w/PTT

12082-0650-14

Headset, Heavy Duty, Over-the-Head, w/PTT

12082-0650-15

Headset, Behind-the-Head, Boom Mic, Earpiece, w/PTT

12082-0650-16

Headset, Tactical, Boom Mic, Earpiece, w/PTT

12082-0650-17

Skull Mic, w/Body PTT and Earcup

12082-0650-18

Throat Mic, W/Acoustic Tube & Body PTT

12082-0650-19

Throat Mic, w/Acoustic Tube, Body and Ring PTT

LS103239V1

Earphone, Lapel Microphone, 2.5mm

LS103239V2

Earphone, Lapel Microphone, 2.5mm, RT Angle

12150-1000-01

Speaker Mic, Premium, Fire (FSM), Noise Cancelling

3.2 CLASS 1, DIVISION 1 OPTION (APPLIES TO XL-200P C1D1 NONREBANDED AND XL-200P C1D1 REBANDED)

Radios ordered with the Class 1, Division 1 option are considered “intrinsically safe apparatus” and are

suitable for use in the following locations:

US:

Class I, Division 1, Groups C and D; Class II, Division 1, Groups E, F and G; Class III, Division 1 hazardous locations; Class 1, Division 2, Groups A, B, C and D or non-hazardous (unclassified) locations only.

Classe I, Division 1 , Groupes C et D; Classe II , Division 1, Groupes E , F et G; Classe III, Division 1 emplacements dangereux; Classe 1, Division 2, Groupes A, B , C et D, ou en sites non-hasardeux (nonclassifiés) seulement.

Canada:

Class 1, Division 2, Groups A, B, C, and D or non-hazardous (unclassified) locations only. Classe 1, Division 2 sont adéquates pour utilisation en Classe 1, Division 2, Groupes A, B, C et D, ou en

lieux non-hasardeux (non-classifiés) seulement

EXPLOSION HAZARD – REPLACE BATTERY PACK ONLY IN AN AREA KNOWN TO BE NON-HAZARDOUS, AND ONLY WITH HARRIS PART NO. 14035-4045-01.

EXPLOSION HAZARD – Substitution of any component may impair suitability for Class I, Division 1; Class II, Division 1; Class III, Division 1; or Class 1, Division 2.

AVERTISSEMENT – RISQUE D’EXPLOSION – Une substitution de toute composante pourrait compromettre la convenance pour la Classe I, Division 1; Classe II , Division 1; Classe III , Division 1; ou Classe 1 , Division 2.

WARNING

14221-1800-2000, Rev. G

EXPLOSION HAZARD – Do not exceed maximum battery charging current of 1.7 A or maximum charging voltage of 8.4 V DC at any time.

CAUTION - The battery used in this device may present a risk of fire or explosion when heated above 100°C (212°F) or incinerated. Replace battery with Harris Part No. 14035-4045-01 only. Use of another battery may present a risk of fire or explosion.

EXPLOSION HAZARD – In addition to any simple single-ended coil antenna and carrying case option, only the following Harris accessories may be used with this radio:

PART NUMBER

DESCRIPTION

Approved Hazardous Locations

12082-0600-01

Standard Speaker Mic – Non-Antenna

US: Class I, Division 1, Groups C and D; Class II, Division 1, Groups E, F and G; Class III, Division 1 hazardous locations; Class 1, Division 2, Groups A, B, C and D

Canada: Class 1, Division 2, Groups A, B, C and D

12082-0600-02

Speaker Microphone, Emergency Button

US: Class I, Division 1, Groups C and D; Class II, Division 1, Groups E, F and G; Class III, Division 1 hazardous locations; Class 1, Division 2, Groups A, B, C and D

Canada: Class 1, Division 2, Groups A, B, C and D

12082-0600-03

Speaker Microphone, Emergency Button, Antenna, 18”

US: Class I, Division 1, Groups C and D; Class II, Division 1, Groups E, F and G; Class III, Division 1 hazardous locations; Class 1, Division 2, Groups A, B, C and D

Canada: Class 1, Division 2, Groups A, B, C and D

12082-0650-13

Headset, Heavy Duty, Behind-theHead, w/PTT

US: Class I, Division 1, Groups C and D; Class II, Division 1, Groups E, F and G; Class III, Division 1 hazardous locations; Class 1, Division 2, Groups A, B, C and D

Canada: Class 1, Division 2, Groups A, B, C and D

12082-0650-14

Headset, Heavy Duty, Over-the-Head, w/PTT

US: Class I, Division 1, Groups C and D; Class II, Division 1, Groups E, F and G; Class III, Division 1 hazardous locations; Class 1, Division 2, Groups A, B, C and D

Canada: Class 1, Division 2, Groups A, B, C and D

WARNING

14221-1800-2000, Rev. G

PART NUMBER

DESCRIPTION

Approved Hazardous Locations

LS103239V1

Earphone for speaker/mic

US: Class I, Division 1, Groups C and D; Class II, Division 1, Groups E, F and G; Class III, Division 1 hazardous locations; Class 1, Division 2, Groups A, B, C and D

Canada: Class 1, Division 2, Groups A, B, C and D

LS103239V2

Earphone for speaker/mic, Right Angle

US: Class I, Division 1, Groups C and D; Class II, Division 1, Groups E, F and G; Class III, Division 1 hazardous locations; Class 1, Division 2, Groups A, B, C and D

Canada: Class 1, Division 2, Groups A, B, C and D

12082-0600-04

Speaker Microphone, Emergency Button, Antenna, 25.6”

US: Class I, Division 1, Groups C and D; Class II, Division 1, Groups E, F and G; Class III, Division 1 hazardous locations; Class 1, Division 2, Groups A, B, C and D

Canada: Class 1, Division 2, Groups A, B, C and D

12082-0600-05

Speaker Microphone, Emergency Button, Antenna, 30”

US: Class I, Division 1, Groups C and D; Class II, Division 1, Groups E, F and G; Class III, Division 1 hazardous locations; Class 1, Division 2, Groups A, B, C and D

Canada: Class 1, Division 2, Groups A, B, C and D

14221-1800-2000, Rev. G

4. INTRODUCTION

4.1 DESCRIPTION

The XL-Series portable radios provide the advanced connectivity that first responders require while addressing evolving voice and data communications. They meet MIL-STD-810G for durability and are certified to more stringent MIL-STD parameters for contamination by fluids and explosive atmospheres. XL portable radios support P25 Trunking, P25 Conventional, Enhanced Digital Access Communications System (EDACS), analog conventional, and BeOn® over a Wi-Fi® or LTE network.

EDACS operation is not supported in UHF or VHF. Refer to Feature Manual 14221-7200-6130 for details on configuring and using BeOn on

the XL Series radios.

Radio features include:

• Extremely Rugged – exceeds the standards of other radios on the market.

• Multiband Operation – supports any combination of VHF, UHF, and 700/800 MHz frequencies.

Also, allows different bands to be enabled for selected users.

• Single-key DES Encryption – provides basic secure communications without having to buy the

complete encryption option.

• Instant Recall of Received Audio – allows user to replay the last transmission received to avoid

unnecessary repetition.

• Active Noise Cancellation – with three internal microphones to transmit intelligible audio from users

in loud environments.

• Built-in GPS – for location reporting and rapid response for emergencies.

• Integrated Bluetooth® – for wireless interface to selected accessories.

• Wi-Fi Connectivity – permits simple and easy radio software and personality updates.

• Wi-Fi Access Point – Radios that include the LTE option can be configured via RPM2 to act as a Wi-

Fi access point and/or router, providing access to broadband data for Wi-Fi devices. Refer to RPM2’s online help when configuring the radio for these functions.

• Covert Mode – allows users to quickly configure the radio for operation in a covert environment.

• Fully Programmable Keypad – each key can be programmed to a variety of functions.

• 4-position switch – provides added configuration flexibility.

• Unique User Interface – tools specially designed by first responders make radio operation simple and

intuitive. An easy-to-read multi-color front display and a monochromatic top display with optional colored backlighting enhance communications for improved user safety.

For optional accessories, refer to Table 4-1. Additional accessories may have been added since publication of this manual; contact Harris for more information.

4.2 STORAGE GUIDELINES

Store your radio and batteries in a clean, cool (not exceeding 86 °F [+30 °C]), dry, and ventilated storage area.

NOTE

14221-1800-2000, Rev. G

4.3 BASIC SETUP

4.3.1 Assemble the Radio

Only use a Harris charger approved for the battery chemistry. Injury could occur from improper charger use.

Do not over-tighten the antenna as damage could result.

Please charge battery fully before first use. Due to government regulations, batteries ship in a discharged state and may require up to two (2) minutes in a charger for successful initialization. During initialization, the charger will not show any charge indication. After this initialization period, charging will resume normally.

1. Make sure batteries are charged per the manual supplied with the charger.

2. To attach optional belt clip, remove the existing tab from the back of the radio above the battery

compartment. Slide the belt clip into the groove.

3. Lift clip, if installed, and slide top of battery into top of battery compartment at the rear of the radio.

4. Press down on bottom side of battery until it snaps into place.

Figure 4-1: Radio Assembly

WARNING

CAUTION

NOTE

14221-1800-2000, Rev. G

4.3.2 Removing the Battery

To remove, press and hold the two tabs at the bottom of the battery and then pull battery up and out of the radio.

Figure 4-2: Remove the Battery

4.3.3 Removing the Optional Belt Clip or D-Post

Remove the battery before removing the belt clip or D-Post. To remove the belt clip, pry up on the metal spring towards the top of the battery compartment (see Figure 4-3) using a flat head screwdriver and slide the belt clip or D-Post out of the groove in the back of the radio.

Figure 4-3: Remove Belt Clip

14221-1800-2000, Rev. G

4.3.4 Install the SIM Card

Figure 4-4 shows how to install the SIM card in the LTE version of the radio.

Figure 4-4: SIM Card Installation

14221-1800-2000, Rev. G

4.4 UNIVERSAL DEVICE CONNECTOR

The Universal Device Connector (UDC) provides connections for external accessories such as a headset, a speaker-microphone, audio test box, audio test cables, and programming cables. The UDC is located on the right side of the radio, opposite the PTT Button. The UDC facilitates programming and testing the radio. The UDC pins perform different functions depending on the accessory attached to the UDC.

Figure 4-5: Universal Device Connector

4.5 CLEANING

Keep the exterior of the radio, battery, antenna, and radio accessories clean.

Periodically clean using the following procedures:

1. To remove dust and dirt, clean using damp clean cloth (warm water and mild detergent soap).

2. Follow by wiping with damp (warm water) clean cloth. Wipe dry with clean cloth.

3. Remove the battery and wipe the battery and radio contacts using a soft dry cloth to remove dirt or

grease. This will ensure efficient power transfer from the battery to the radio.

4. Remove any accessories and clean the UDC contacts using a clean dry cloth. When the UDC is not

in use, cover the connector with the protective dust cap to prevent the build-up of dust or water particles.

5. If the radio is used in a harsh environment (such as driving rain, salt fog, etc.), it may be necessary to

periodically dry and clean the battery and radio contacts with a soft dry cloth or soft-bristle nonmetallic brush.

14221-1800-2000, Rev. G

For more rigorous cleaning, use the following procedure:

Do not use chemical cleaners, spray, or petroleum-based products. They may damage the radio housing. We recommend using Chemtronics® Electro-Wash® PR (ES-1603) or equivalent.

1. Apply the cleaning solution to a clean damp cloth and clean the radio.

Do not spray cleaning solution directly on radio. To clean the radio in the speaker and microphone areas, carefully wipe these areas but prevent the cleaning solution from entering the speaker or microphone openings.

2. Wipe off the radio with clean damp cloth using mild warm soapy water.

3. Follow up by wiping off the radio with clean damp cloth using warm water only.

4. Wipe dry with clean cloth.

4.6 OPTIONS AND ACCESSORIES

Only use Harris approved accessories. Refer to Harris’ Product and Services catalog for the complete list of options and accessories available. Contact Harris for requirements not contained in this list:

Always use the correct options and accessories (battery, antenna, speaker/mic, etc.) for the radio. Immersion rated options must be used with an immersion rated radio. Refer to Table 4-1.

ONLY accessories marked with an asterisk (*) are approved for use with C1D1 radios.

Table 4-1: Options and Accessories

DESCRIPTION

PART NUMBER

OPTION NUMBER

ANTENNAS

Antenna, Full Spectrum XL-200P Only*

14035-4000-01*

XL-NC5Z*

Antenna, Whip Wideband 378-520 MHz, 762-870 MHz XL-200P Only*

14035-4420-01*

XL-NC8E*

Antenna, Whip, 1/4 Wave, 762-870 MHz XL-200P Only*

14035-4440-02*

XL-NC8F*

Antenna, Whip, 1/2 Wave, 762-870 MHz XL-200P Only*

14035-4440-01*

XL-NC8D*

Antenna, Whip, 1/4 Wave, 762-944 MHz XL-185P Only (Not approved w/LTE Option)

14035-4450-02

XL-NC9F

Antenna, Whip, 1/2 Wave, 762-944 MHz XL-185P Only (Approved w/LTE Option)

14035-4450-01

XL-NC9D

Antenna, 896-941 MHz XL-185P Only (Not approved w/LTE Option)

KRE1011223/02

MAEX-NNC1Z

BATTERIES/CHARGERS

Battery, Lithium, Standard Capacity

14035-4010-01

XL-PA3V

Battery, Li-Ion, 3100 mAH

14035-4010-04

XL-PA3V

Approved for use with C1D1 radios.

CAUTION

NOTE

CAUTION

+ 92 hidden pages

HARRIS TR 0144 E, TR 0146 E User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual