Updated Declaration of Conformity. Added EU regulatory approval information (standards) and
EU RF exposure information.
Updated Table 1-1 and Tableau 2-1. Updated for XLP R2A. Added note to Secti on 4.3.1
regarding charging the battery before first use. Updated Appendix A. Updated Section 4.3.3.
Updated Sections 1.2, 4.1, 4.6, 5.8, 5.12, 10, included XLP R3A features, and added Sections
4.3.4, 5.35, and 5.6.
F
Feb/17
Updated to add XLP R4A features. Added XL-185.
MANUAL REVISION HISTORY
C Jan/16
D Jul/16
E Jan/17
ACKNOWLEDGEMENT
This product was developed using GEOTRANS, a product of the National Geospatial Intelligence Agency and U.S. Army Engineering
Research and Development C enter. Use of this software does not indicat e endorsement or approval of the product by the Secret ary of
Defense or the National Geospatial Intelligence Agency.
This device made under license under one or more of the following US patents: 4,590,473; 4,636,791; 5,148,482; 5,185,796; 5,271,017;
5,377,229; 4,71 6, 4 07; 4,972,460; 5,502,767; 5,146,697 ; 5,164,986; 5,185,795.
The Advanced Multi-Band Excitation implementation 2 (AMBE+2) voice coding Technology embodied in this product is protected by
intellectual property rights including patent rights, copyrights and trade secrets of Digital Voice Systems, Inc. This voice coding
Technology is licensed solely for use within this Communications Equipment. The user of this Technology is explicitly prohibited from
attempting to extract, re move, decompile, revers e engineer, o r disassemble the Ob ject Code, or in any other way convert the Object Code
into a human-readable form. U.S. Patent Nos. #5,870,405, #5,826,222, #5,754,974, #5,701,390, #5,715,365, #5,649,050, #5,630,011,
#5,581,656, #5,517,511, #5,491,772, #5,247,579, #5,226,084 and #5,195,166.
CREDITS
Harris, Unity, VIDA, EDACS, NetworkFirst, and OpenSky are registered trademarks of Harris Corporation. TECHNOLOGY TO
CONNECT, INFORM AND PROTECT is a trademark of Harris Corp orati on .
Bluetooth is a registered trademark of Bluetooth SIG, Inc.
Motorola is a registered trademark of Motorola, Inc.
AMBE is a registered trademark and IMBE, AMBE+, and AMBE+2 are trademarks of Digital Voice Systems, Inc.
Wi-Fi is a registered trademark of
All brand and product names are trademarks, registered trademarks, or service marks of their respective holders.
The material contained herein is subject to U.S. export approval. No export or re-export is permitted without written approval from the U.S.
Government. Rated: EAR99; in accordance with U.S. Dept. of Commerce regulations 15CFR774, Export Administration Regulations.
Information and descriptions contained herein are the property of Harris Corporation. Such information and descriptions may not be copied
or reproduced by any means, or disseminated or distributed without the express prior written permission of Harris Corporation, PSPC
Business, 221 Jefferson Ridge Parkway, Lynchburg, VA 24501.
Repairs to this equipment should be made only by an authorized service technician or facility designated by the supplier. Any repairs,
alterations or substitutions of recommended parts made by the user to this equipment not approved by the manufacturer could void the
user's authority to operate the equipment in addition to the manufacturer's warranty.
Wi-Fi Alliance.
NOTICE!
This product conforms to the European Union WEEE Directive 2012/19/EU. Do not dispose of this product in a public
landfill. Take it to a recycling center at the end of its life.
Harris products comply with the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic
Equipment (RoHS) Directive.
This manual is published by Harris Corporation without any warranty. Improvements and changes to this manual necessitated by typographical errors,
inaccuracies of current information, or improvements to programs an d/or equipment, may be made by Harris Corporation at any time and without notice.
Such changes will be incorporated into new editions of this manual. No part of this manual may be reproduc ed or transmitted in any form or by any means,
electronic or mechanical, including photocopying and recording, for any purpose, without the express written permission of Harris Corporation.
This device is a RF transceiver intended for land mobile radio applications. The device may have use restriction s, which require th at the
national authority be contacted for any system licensing requi r ements, frequency use, allowable power l evel , etc.
3
14221-1800-2000, Rev. F
4
14221-1800-2000, Rev. F
DECLARATION OF CONFORMITY
Česky [Czech]
Harris Corporation tímto prohlašuje, že tento XL-200P je ve shodě se základními požadavky a
dalšími příslušnými ustanoveními směrnice 1999/5/ES.
væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Hiermit erklärt
dass sich das Gerät XL-200P in Übereinstimmung mit den
1999/5/EG befindet.
põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.
Hereby,
, declares that this
is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.
Español
[Spanish]
Por medio de la presente Harris Corporation declara que el XL-200P cumple con los requisitos
esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
Ελληνική
[Greek]
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Harris Corporation ΔΗΛΩΝΕΙ ΟΤΙ XL-200P ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ
ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.
Français
[French]
Par la présente Harris Corporation déclare que l'appareil XL-200P est conforme aux exigences
essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE.
essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
Latviski
[Latvian]
Ar šo Harris Corporationdeklarē, XG 25P UHF-L(378-470 MHz), 7/800 (764-870MHz) atbilst
Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.
Lietuvių
[Lithuanian]
Šiuo Harris Corporation deklaruoja, kad šis XL-200P atitinka esminius reikalavimus ir kitas
1999/5/EB Direktyvos nuostatas.
[Dutch]
essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.
Malti [Maltese]
Hawnhekk, Harris Corporation, jiddikjara li dan XL-200P jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC.
Magyar
[Hungarian]
Alulírott, Harris Corporation nyilatkozom, hogy a XL-200P megfelel a vonatkozó alapvetõ
követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.
Polski [Polish]
Niniejszym Harris Corporationoświadcza, że XL-200P jest zgodny z zasadniczymi wymogami
oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.
[Portuguese]
outras disposições da Directiva 1999/5/CE.
[Slovenian]
izjavlja, da je ta
v skladu z bistvenimi zahtevami in ostalimi
relevantnimi določili direktive 1999/5/ES.
Slovensky
[Slovak]
Harris Corporation týmto vyhlasuje, že XL-200P spĺňa základné požiadavky a všetky príslušné
ustanovenia Smernice 1999/5/ES.
Suomi [Finnish]
Harris Corporation vakuuttaa täten että XL-200P tyyppinen laite on direktiivin 1999/5/EY
oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.
[Swedish]
väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.
[Icelandic]
kröfur, sem gerðar eru í tilskipun 1999/5/EC.
Norsk
[Norwegian]
Harris Corporation erklærer herved at utstyret XL-200P er i samsvar med de grunnleggende krav
og øvrige relevante krav i direktiv 1999/5/EF.
Dansk [Danish] Undertegnede Harris Corporation erklærer herved, at følgende uds tyr XL-200P overholder de
Deutsch
[German]
Eesti [Estonian]
English
Italiano [Italian] Con la presente Harris Corporation dichiara che questo XL-200P è conforme ai requisiti
Nederlands
grundlegenden Anforderu n gen und den übrigen einschlägigen Bestimm ungen der Richtlinie
Figure A-3: Service Name ........................................................................................................................... 111
Figure A-4: Enable Wi-Fi in RPM2 ............................................................................................................. 111
Figure A-5: Enable Wi-Fi Programming Mode on XL-200P ...................................................................... 112
Figure A-6: RPM2 Radio tab - Wi-Fi .......................................................................................................... 113
Table 1-2: Worst Case Reported SAR Level ................................................................................................. 13
Table 10-1: Displayed Error Messages, Reasons, and Resolutions ............................................................ 106
Table 12-1: Wi-Fi Feature Support .............................................................................................................. 113
Harris Corporation, Public Safety and Professional Communications (PSPC) Business continually evaluates its technical publications for
completeness, technical accuracy, and organization. You can assist in this process by submitting your comments and suggestions to the
following:
Harris Corporationfax your comments to: 1-434-455-6851
PSPC Business or
Technical Publications e-mail us at: PSPC_TechPubs@harris.com
221 Jefferson Ridge Parkway
Lynchburg, VA 24501
10
14221-1800-2000, Rev. F
The WARNING symbol calls attention to a procedure, practice, or the like, which, if
personal injury. Do not
proceed beyond a WARNING symbol until the conditions identified are fully
understood or met.
The Harris XL-200P/XL-185P portable radio generates RF electromagnetic energy
Use Only,” meaning it must be used only during the course of employment by
he hazards and the ways to minimize such hazards. This
radio is NOT intended for use by the “General Population” in an uncontrolled
environment.
WARNING
CAUTION
NOTE
WARNING
1. REGULATORY AND SAFETY INFORMATION
1.1 SAFETY CONVENTIONS
The following conventions are used throughout this manual to alert the user to general safety precautions
that must be observed during all phases of operation, service, and repair of this product. Failure to comply
with these precautions or with specific warning elsewhere in this manual violates safety standards of
design, manufacture, and intended use of the product. Harris assumes no liability for the customer’s
failure to comply with these standards.
not correctly performed or adhered to, could result in
The CAUTION symbol calls attention to an operating procedure, practice, or the like,
which, if not performed correctly or adhered to, could result in damage to the equipment
or severely degrade the equipment performance.
The NOTE symbol calls attention to supplemental information, which may improve
system performance or clarify a process or procedure.
1.2 SAFETY TRAINING INFORMATION
during transmit mode. This radio is designed for and classified as “Occupational
individuals aware of t
The XL-200P/XL-185P portable radio has been tested and complies with the FCC RF exposure limits for
“Occupational Use Only.” In addition, this Harris radio complies with the following Standards and
Guidelines with regard to RF energy and electromagnetic energy levels and evaluation of such levels for
exposure to humans:
• FCC KDB Publication 447498 General RF Exposure Guidance
• American National Standards Institute (C95.1 – 1992), IEEE Standard for Safety Levels with Respect
to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz.
• American National Standards Institute (C95.3 – 1992), IEEE Recommended Practice for the
Measurement of Potentially Hazardous Electromagnetic Fields – R F and Microw a v e.
• IC Standard RSS-102. Radiofrequency Exposure Compliance of Radiocommunication Apparatus
(All Frequency Bands).
• European Council Directive 89/391/EEC.
11
14221-1800-2000, Rev. F
CAUTION
1.2.1 RF Exposure Guidelines
To ensure that exposure to RF electromagnetic energy is within the EU/AU/FCC/IC
allowable limits for occupational use, always adhere to the following guidelines:
• DO NOT operate the radio without a proper antenna attached, as this may damage the radio and may
also cause the FCC RF exposure limits to be exceeded. A proper antenna is the antenna supplied with
this radio by Harris or an antenna specifically authorized by Harris for use with this radio. (Refer to
Table 4-1.)
• DO NOT transmit for more than 50% of total radio use time (“50% duty cycle”). Transmitting more
than 50% of the time can cause FCC RF exposure compliance requirements to be exceeded. The radio
is transmitting when the “TX” indicator appears in the display. The radio will transmit by pressing the
“PTT” (Push-To-Talk) button.
• ALWAYS transmit using low power when possible. In addition to conserving battery charge, low
power can reduce RF exposure.
• ALWAYS use Harris authorized accessories (antennas, batteries, belt clips, speaker/mics, etc.). Use
of unauthorized accessories may cause the FCC Occupational/Controlled Exposure RF compliance
requirements to be exceeded. (Refer to Table 1-1.)
• As noted in Table 1-1, ALWAYS keep the housing of the transmitter AT LEAST 0.47 inches (1.2
cm) from the body and at least 0.98 in (2.5 cm) from the face when transmitting to ensure
EU/AU/FCC/IC RF exposure compliance requirements are not exceeded. However, to provide the
best sound quality to the recipients of your transmission, Harris recommends you hold the
microphone at least 2 in (5 cm) from mouth, and slightly off to one side.
Minimum safe operating distances for the radio are based on the Harmonized Standards and SAR evaluation.
2
This is worst case based on the thinnest body mount accessory (belt clip).
Body2 Face
0.47 in (1.2 cm) 0.98 in (2.5 cm)
0.47 in (1.2 cm) 0.98 in (2.5 cm)
0.47 in (1.2 cm) 0.98 in (2.5 cm)
0.47 in (1.2 cm) 0.98 in (2.5 cm)
TESTED DISTANCES
(worst case scenario)
12
14221-1800-2000, Rev. F
Body2
Face
(2412 - 2472 MHz)
ACCESSORY
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
NOTE
RADIO FREQUENCY
5 GHz
(5.18 - 5.825 GHz)
0.47 in (1.2 cm) 0.98 in (2.5 cm)
TESTED DISTANCES
(worst case scenario)
Table 1-2: Worst Case Reported SAR Level
LMR STANDALONE SIMULTANEOUS LMR AND LTE
Head 1.88 W/kg 2.25 W/kg
Body-worn 5.63 W/kg 5.93 W/kg
FCC SAR Limit 8.0 W/kg 8.0 W/kg
SAR Evaluation: 1g averaged, 50% PTT Duty Factor, Occupational/Controlled Exposure.
This device contains multiple transmitters that may operate simultaneously, see Table 1-3 Simultaneous
Transmission Scenarios for the capable transmit configurations.
LTE B13/14 + 700 MHz combination is not supported by this device.
The information in this section provides the information needed to make the user aware of RF exposure,
and what to do to assure that this radio operates within the FCC RF exposure limits.
1.2.2 Electromagnetic Interference/Compatibility
During transmissions, this Harris radio generates RF energy that can possibly cause interference with
other devices or systems. To avoid such interference, turn off the radio in areas where signs are posted to
do so. DO NOT operate the transmitter in areas that are sensitive to electromagnetic radiation such as
hospitals, aircraft, and blasting sites.
1.3 REGULATORY APPROVALS
Changes or modifications not expressly approved by the manufacturer could void the user’s authority to
operate the equipment.
1.3.1 Part 15
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired
operation.
1.3.2 Industry Canada
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
1.4 OPERATING TIPS
Antenna location and condition are important when operating a portable radio. Operating the radio in
low-lying areas or terrain, under power lines or bridges, inside of a vehicle, or in a metal framed building
can severely reduce the range of the unit. Mountains can also reduce the range of the unit.
In areas where transmission or reception is poor, some improvement may be obtained by ensuring that the
antenna is vertical. Moving a few yards in another direction or moving to a higher elevation may also
improve communications. Vehicular operation can be aided with the use of an externally mounted
antenna.
Battery condition is another important factor in the trouble free operation of a portable radio. Always
properly charge the battery.
1.4.1 Efficient Radio Operation
Keep the antenna in a vertical position when receiving or transmitting a message.
14
14221-1800-2000, Rev. F
Do not use the portable radio with a damaged or missing antenna. A minor burn
may result if a damaged antenna comes into contact with the skin. Replace a
Use only the supplied or approved antenna. Unauthorized antennas, modifications, or
RF energy from portable radios may affect some electronic equipment. Most modern
WARNING
WARNING
CAUTION
CAUTION
WARNING
WARNING
Do NOT hold onto the antenna when the radio is powered on!
1.4.2 Antenna Care and Replacement
damaged antenna immediately. Operating a portable radio with the antenna missing
could cause personal injury, damage the radio, and may violate FCC regulations.
attachments could cause damage to the radio unit and may violate FCC regulations. (Refer
to Table 4-1.)
1.4.3 Electronic Devices
electronic equipment in cars, hospitals, homes, etc. is shielded from RF energy. However,
in areas in which you are instructed to turn off two-way radio equipment, always observe
the rules. If in doubt, turn it off!
1.4.4 Aircraft
• Always turn off a portable radio before boarding any aircraft!
• Use it on the ground only with crew permission.
• DO NOT use while in-flight!!
1.4.5 Electric Blasting Caps
To prevent accidental detonation of electric blasting caps, DO NOT use two-way
radios within 1000 feet of blasting operations. Always obey the "Turn Off Two-Way
Radios" signs posted where electric blasting caps are being used (OSHA Standard:
1926.900).
15
14221-1800-2000, Rev. F
Areas with potentially explosive atmospheres are often, but not always, clearly
WARNING
1.4.6 Potentially Explosive Atmospheres
marked. These may be fueling areas, such as gas stations, fuel or chemical transfer
or storage facilities, and areas where the air contains chemicals or particles, such as
grain, dust, or metal powders.
Sparks in such areas could cause an explosion or fire resulting in bodily injury or
even death.
Turn off two-way radios when in any area with a potentially explosive atmosphere. It
is rare, but not impossible that a radio or its accessories could generate sparks.
16
14221-1800-2000, Rev. F
Le symbole MISE EN GARDE attire l’attention sur une procédure ou une
pratique qui, si elle n’est pas correctement effectuée ou observée, pourrait
ant que les conditions identifiées soient complètement
opérationnelle qui, si elle n’est pas correctement effectuée ou observée, pourrait
produit de l’énergie
MISE EN GARDE
AVERTISSEMENT
REMARQUE
MISE EN GARDE
2. RENSEIGNEMENTS SUR LA RÉGLEMENTATION ET
SÉCURITÉ
2.1 CONVENTIONS SUR LES SYMBOLES DE SÉCURITÉ
Les conventions suivantes sont utilisées dans le présent manuel pour avertir l’utilisateur des précautions générales de
sécurité qui doivent être observées pendant toutes les phases d’opération, d’entretien et de réparation de ce produit.
Le non-respect de ces précautions ou d’avertissements précisés ailleurs enfreint les normes de sécurité de la
conception, de la fabrication et de l’utilisation prévue du produit. Harris n’assume aucune responsabilité pour le
non-respect de ces normes par le client.
entraîner une blessure personnelle. Ne pas poursuivre au-delà d’un symbole de
MISE EN GARDE av
comprises ou satisfaites.
Le symbole AVERTISSEMENT attire l’attention sur une procédure ou une pratique
entraîner un bris d’équipement ou une importante baisse de rendement de l’équipement.
Le symbole REMARQUE attire l’attention sur des renseignements supplémentaires qui
peuvent améliorer le rendement du système ou clarifier un processus ou une procédure.
2.2 RENSEIGNEMENTS SUR LA FORM ATIO N S UR LA SÉCURITÉ
La radio portative Harris XL-200P/XL-185P
électromagnétique des RF lorsqu’en mode de transmission. Cette radio est conçue
et classée pour une « Utilisation professionnelle seulement », ce qui signifie qu’elle
ne doit être utilisée que dans le cadre d’un emploi par des individus co ns cien ts des
risques et des moyens de limiter ceux-ci. Cette radio N’EST PAS conçue pour une
utilisation par la « Population générale » dans un environnement non contrôlé.
La radio portative XL-200P/XL-185P a été testée et est conforme aux limites d’exposition aux RF de la
FCC pour une « Utilisation professionnelle seulement ». De plus, cette radio Harris est conforme aux
normes et directives suivantes quant à l’énergie des RF et aux niveaux d’énergie électromagnétique, ainsi
qu’à l’évaluation de ces niveaux pour l’exposition aux humains:
• FCC KDB 447498
• American National Standards Institute (C95.1 – 1992), norme de l’IEEE sur les niveaux sécuritaires
d’exposition humaine aux champs électromagnétiques des radiofréquences, 3 kHz à 300 GHz.
• American National Standards Institute (C95.3 – 1992), pratique recommandée par l’IEEE pour la
mesure des champs électromagnétiques potentiellement dangereux – R F et m icro -ondes.
17
14221-1800-2000, Rev. F
AVERTISSEMENT
2.2.1 Directives sur l’exposition aux RF
Pour s’assurer que l’exposition à l’énergie électromagnétique des RF se situe dans les
limites acceptables de la FCC pour l’utilisation professionnelle, respectez toujours les
directives suivantes :
• N’utilisez PAS la radio sans qu’une antenne appropriée y soit connectée, car ceci peut endommager la
radio et également causer un dépassement des limites d’exposition aux RF de la FCC. Une antenne
appropriée est celle fournie par Harris avec cette radio, ou une antenne spécifiquement autorisée par
Harris pour être utilisée avec cette radio. (Reportez-vous à Tableau 2-1.)
• Ne transmettez PAS pendant plus de 50 % de la durée d’utilisation totale de la radio (« cycle de
service de 50 % »). La transmission pendant plus de 50 % du temps peut causer un dépassement des
exigences de conformité de la FCC en matière d’exposition aux RF. La radio transmet lorsque
l’indicateur « TX » apparaît sur l’affichage. La radio transmet lorsqu’on appuie sur le bouton « PTT »
(bouton de microphone).
• Transmettez TOUJOURS en basse puissance lorsque possible. En plus de préserver la charge de la
pile, une faible puissance réduit l’exposition aux RF.
• Utilisez TOUJOURS des accessoires autorisés Harris (antennes, piles, pinces de ceinture, haut-
parleurs/micros, etc.). L’utilisation d’accessoires non autorisés peut entraîner un dépassement des
exigences de conformité pour une exposition aux RF professionnelle ou contrôlée de la FCC.
(Reportez-vous à Table 4-1.)
• Tel qu’indiqué dans Tableau 2-1, conservez TOUJOURS l’appareil et son antenne à AU MOINS
1,2 cm du corps, et à au moins 2,5 cm du visage pendant la transmission, pour vous assurer de ne pas
dépasser les exigences de conformité de la FCC en matière d’exposition aux RF. Cependant, pour
offrir la meilleure qualité sonore aux auditeurs de votre transmission, Harris recommande de tenir le
microphone à au moins 5 cm (2 po) de votre bouche et légèrement déplacé sur un côté.
Tableau 2-1 : Distances de test de conformité des expositions aux RF
Ce est le pire des cas basée sur le corps plus mince monter accessoire (clip ceinture).
18
14221-1800-2000, Rev. F
(2412 - 2472 MHz)
RADIOFRÉQUENCES
5 GHz
(5.18 - 5.825 GHz)
1,2 cm 2,5 cm
DISTANCES TESTÉES
(pire des scénarios)
Dans cette section figurent les renseignements nécessaires pour sensibiliser l’utilisateur à l’exposition aux
RF et sur ce qu’il faut faire pour s’assurer que cette radio fonctionne dans les limites d’exposition aux RF
de la FCC.
Pendant les transmissions, cette radio Harris produit de l’énergie des RF qui peut causer de l’interférence
avec d’autres appareils ou systèmes. Pour éviter de telles interférences, fermez la radio dans les zones où
il est indiqué de le faire. N’utilisez PAS le transmetteur dans des zones sensibles aux radiations
électromagnétiques, com me les hôp itaux , les av ions et les sites de détonat ion.
2.3 INTERFÉRENCE DES RADIOFRÉQUENCE S
2.3.1 Partie 15 de la FCC
Cet appareil est conforme à la Partie 15 de la réglementation de la FCC. Le fonctionnement est soumis
aux deux conditions suivantes :
1. Cet appareil ne doit pas causer une interférence nuisible; et
2. Cet appareil doit accepter toute interférence reçue, y compris une interférence qui peut causer un
fonctionnement non souhaité.
2.3.2 Industrie Canada
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de
brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en com p rom ettre le fonctionnement.
2.4 CONSEILS D’UTILIS ATION
L’emplacement et l’état de l’antenne sont importants pour l’utilisation d’une radio portative. L’utilisation
de la radio dans des zones de faible élévation, sous des lignes électriques ou des ponts, à l’intérieur d’un
véhicule ou dans un immeuble à ossature métallique, peut réduire la portée de l’appareil de manière
considérable. Les montagnes peuvent également réduire la portée de l’unité.
Dans les zones où la transmission ou la réception est insatisfaisante, certaines améliorations peuvent être
obtenues en s’assurant que l’antenne est verticale. Se déplacer de quelques mètres dans une autre
direction ou à un emplacement plus élevé peut également améliorer les communications. L’utilisation
d’une antenne fixée à l’extérieur peut faciliter le fonctionnement dans un véhicule.
L’état de la pile est un autre facteur important d’une utilisation sans tracas d’une radio portative. Chargez
toujours correctement la pile.
2.4.1 Utilisation Efficace de la Radio
Gardez l’antenne dans une position verticale pendant la réception ou la transmission d’un message.
19
14221-1800-2000, Rev. F
N’utilisez pas la radio portative si son antenne est endommagée ou absente. Une
brûlure légère peut se produire au contact d’une antenne endommagée avec la
peau. Remplacez immédiatement une antenne endommagée. L’utilisation d’une
radio portative alors que l’antenne est absente peut causer des blessures,
Utilisez seulement l’antenne fournie ou une antenne approuvée. Des antennes non
autorisées, des modifications ou des ajouts à une antenne peuvent endommager la radio et
L’énergie des RF provenant de radios portatives peut affecter certains appareils
l’équipement électronique moderne dans les voitures, les
MISE EN GARDE
MISE EN GARDE
AVERTISSEMENT
AVERTISSEMENT
MISE EN GARDE
MISE EN GARDE
Ne tenez PAS l’antenne lorsque la radio est allumée!
2.4.1.1 Entretien Et Remplacement De L’antenne
endommager la radio et pourrait enfreindre la réglementation de la FCC.
enfreindre la réglementation de la FCC. (Reportez-vous à Table 4-1.)
2.4.1.2 Appareils Électroniques
électroniques. La majorité de
hôpitaux, les maisons, etc. est blindé contre l’énergie des RF. Cependant, dans les zones
où l’on vous demande de fermer l’équipement de radio bidirectionnelle, respectez toujours
les règles. En cas de doute, éteignez-le!
2.4.1.3 Avion
• Éteignez toujours une radio portative avant d’embarquer à bord d’un avion!
• Ne l’utilisez au sol qu’avec la permission de l’équipage.
• NE l’utilisez PAS durant le vol!
2.4.1.4 Détonateurs Électriques
Pour prévenir la détonation accidentelle des détonateurs électriques, n’utilisez PAS
de radios bidirectionnelles à moins de 305 m (1 000 pi) des opérations de détonation.
Respectez toujours les indications « Éteindre les radios bidirectionnelles » situées là
où des détonateurs électriques sont utilisés. (Norme OSHA : 1926.900)
20
14221-1800-2000, Rev. F
en carburant, comme les postes d’essence, les installations de stockage ou de
transfert de carburant ou de produits chimiques, ainsi que les zones dont l’air
Éteignez les radios bidirectionnelles dans toute zone ayant une atmosphère
nt explosive. Il est rare, mais pas impossible qu’une radio ou ses
MISE EN GARDE
2.4.1.5 Atmosphère Potentiellement Explosive
Les zones ayant une atmosphère potentiellement explosive sont souvent, mais pas
toujours, identifiées clairement comme telles. Il peut s’agir de zones d’al imentati on
contient des produits chimiques ou des particules, comme des grains, de la poussière
ou des poudres métalliques.
Des étincelles dans de telles zones peuvent provoquer une explosion ou un incendie,
causant ainsi des blessures ou même la mort.
potentielleme
accessoires produisent des étincelles.
21
14221-1800-2000, Rev. F
EXPLOSION HAZARD – REPLACE BATTERY PACK ONLY IN AN AREA
HAZARDOUS, AND ONLY WITH HARRIS PART NO.
LES BATTERIES DOIVENT
BATTERIE HARRIS PORTANT
LE NUMÉRO DE PIÈCE 14035-4010-01.
EXPLOSION HAZARD – Substitution of any component may impair suitability for
Une substitution de toute
composante pourrait compromettre la convenance pour la Classe I, Division 2.
Do not exceed maximum battery charging current of
when heated above 100°C (212°F) or incinerated. Replace battery with Harris Part
01 only. Use of another battery may present a risk of fire or
PART NUMBER
DESCRIPTION
12082-0600-01
SPEAKER MICROPHONE
12082-0600-02
Speaker Microphone, Emergency Button
12082-0650-01
Microphone,Palm,2 Wire, Black
12082-0650-02
Microphone,Palm,2 Wire, Beige
12082-0650-03
Microphone,Mini-Lapel,3 Wire, Black
12082-0650-04
Microphone,Mini-Lapel,3 Wire, Beige
12082-0650-05
EARPHONE KIT, BL AC K,XG-100P
12082-0650-06
EARPHONE KIT, BEIGE,XG-100P
12082-0650-07
Headset, In-Ear, B oom Mic, In-Line PTT
12082-0650-08
Headset, Lightweight, Over-the-Head, Single Ear, In-Line PTT
WARNING
WARNING
WARNING
WARNING
WARNING
3. HAZARDOUS LOCATIONS
Radios ordered with the Class 1, Division 2 option are suitable for use in Class 1, Division 2, Groups A,
B, C, and D or non-hazardous (unclassified) locations only.
Les radios commandées avec l’option Classe 1, Division 2 sont adéquates pour utilisation en Classe 1,
Division 2, Groupes A, B, C et D, ou en lieux non-hasardeux (non-classifiés) seulement
KNOWN TO BE NON14035-4010-01.
AVERTISSEMENT – RISQUE D’EXPLOSION –
ÊTRE REMPLACÉES DANS UNE ZONE RECONNUE NON-HASARDEUSE
SEULEMENT, ET SEULEMENT AVEC UNE
Class I, Division 2.
AVERTISSEMENT – RISQUE D’EXPLOSION –
EXPLOSION HAZARD –
5.250 A or maximum charging voltage of 12.0 V DC at any time.
CAUTION - The battery used in this device may present a risk of fire or explosion
No. 14035-4010-
explosion.
Battery replacement instructions: Remove battery by 1) depress ing b atter y latc hes t hen 2) remove battery
from radio chassis. Install replacement battery by inserting battery in radio chassis opening and
depressing battery into chassis until both battery latches are engaged. Dispose of used battery promptly.
Keep away from children. Do not disassemble and do not dispose of in fire.
EXPLOSION HAZARD – In addition to any simple single-ended coil antenna, only
the following Harris accessori es may be used with t his rad io :
22
14221-1800-2000, Rev. F
PART NUMBER
DESCRIPTION
12082-0650-09
Headset, Lightweight, Behind-the-Head, Dual Ear, In-Line PTT
12082-0650-10
Headset, Lightweight, Behind-the-Head, Dual Ear, Pigtail PTT
Speaker Mic, Premium, Fire (FSM), Noise Cancelling
23
14221-1800-2000, Rev. F
NOTE
NOTE
4. INTRODUCTION
4.1 DESCRIPTION
The XL-200P and XL-185P provide the advanced connectivity that first responders require while
addressing evolving voice and data communications. They support VHF, UHF, and 700/800 MHz,
allowing voice and data communications across agencies using multiple frequencies and systems. The
XL-200P and XL-185P meet MIL-STD-810G for durability and is certified to more stringent MIL-STD
parameters for contamination by fluids and explosive atmospheres. The XL-200P and XL-185P support
P25 Trunking, P25 Conventional, Enhanced Digital Access Communications System (EDACS), analog
conventional, and BeOn
EDACS operation is not supported in UHF or VHF.
Refer to Feature Manual 14221-7200-6130 for details on configuring and using BeOn on
the XL Series radios.
®
over a Wi-Fi® or LTE network.
Radio features include:
• Extremely Rugged – exceeds the standards of other radios on the market.
• Multiband Operation – supports any combination of VHF, UHF, and 700/800 MHz frequencies. Also
allows different bands to be enabled for selected users.
• Single-key DES Encryption – provides basic secure communications without having to buy the
complete encryption option.
• Instant Recall of Received Audio – allows user to replay the last transmission received to avoid
unnecessary repetition.
• Active Noise Cancellation – with three internal microphones to transmit intelligible audio from users
in loud environments.
• Built-in GPS – for location reporting and rapid response for emergencies.
• Integrated Bluetooth
®
– for wireless interface to selected accessories.
• Wi-Fi Connectivity – permits simple and easy radio software and personality updates.
• Wi-Fi Access Point – XL-200P radios that include the LTE option can be configured via RPM2 to act
as a Wi-Fi access point and/or router, providing access to broadband data for Wi-Fi devices. Refer to
RPM2’s online help when configuring the XL-200P for these functions.
• Covert Mode – allows users to quickly configure the radio for operation in a covert environment.
• Fully Programmable Keypad – each key can be programmed to a variety of functions.
• Unique User Interface – tools specially designed by first responders make radio operation simple and
intuitive. An easy-to-read multi-color front display and a monochromatic top display with optional
colored backlighting enhance communications for improved user safety.
14221-1800-2000, Rev. F
Please charge battery fully before first use. Due to government regulations, batteries
minutes in a charger for
indication. After this initialization period, charging will resume normally.
WARNING
CAUTION
NOTE
For optional accessories, refer to Table 4-1. Additional accessories may have been added since
publication of this manual; contact Harris for more information.
4.2 STORAGE GUIDELINES
Store your XL-200P and batteries in a clean, cool (not exceeding 86 °F [+30 °C]), dry, and ventilated
storage area.
4.3 BASIC SETUP
4.3.1 Assemble the Radio
Only use a Harris charger approved for the battery chemistry. Injury could occur
from improper charger use.
Do not over-tighten the antenna as damage could result.
ship in a discharged state and may require up to two (2)
successful initialization. During initialization, the charger will not show any charge
1. Make sure batteries are charged per the manual supplied with the charger.
2. To attach optional belt clip, remove the existing tab from the back of the radio above the battery
compartment. Slide the belt clip into the groove.
3. Lift clip, if installed, and slide top of battery into top of battery compartment at the rear of the radio.
4. Press down on bottom side of battery until it snaps into place.
25
14221-1800-2000, Rev. F
Figure 4-1: Radio Assembly
4.3.2 Removing the Battery
To remove, press and hold the two tabs at the bottom of the battery and then pull battery up and out of the
radio.
Figure 4-2: Remove the Battery
4.3.3 Removing the Optional Belt Clip or D-Post
Remove the battery before removing the belt clip or D-Post. To remove the belt clip, pry up on the metal
spring towards the top of the battery compartment (see Figure 4-3) using a flat head screwdriver and slide
the belt clip or D-Post out of the groove in the back of the radio.
26
14221-1800-2000, Rev. F
Figure 4-3: Remove Belt Clip
27
14221-1800-2000, Rev. F
4.3.4 Install the SIM Card
Figure 4-4 shows how to install the SIM card in the LTE version of XL-200P.
Figure 4-4: SIM Card Installation
28
14221-1800-2000, Rev. F
4.4 UNIVERSAL DEVICE CONNECTOR
The Universal Device Connector (UDC) provides connections for external accessories such as a headset,
a speaker-microphone, audio test box, audio test cables, and programming cables. The UDC is located on
the right side of the radio, opposite the PTT Button. The UDC facilitates programming and testing the
radio. The UDC pins perform different functions depending on the accessory attached to the UDC.
4.5 CLEANING
Keep the exterior of the radio, battery, antenna, and radio accessories clean.
Periodically clean using the following procedures:
1. To remove dust and dirt, clean using damp clean cloth (warm water and mild detergent soap).
2. Follow by wiping with damp (warm water) clean cloth. Wipe dry with clean cloth.
3. Remove the battery and wipe the battery and radio contacts using a soft dry cloth to remove dirt or
grease. This will ensure efficient power transfer from the battery to the radio.
4. Remove any accessories and clean the UDC contacts using a clean dry cloth. When the UDC is not
in use, cover the connector with the protective dust cap to prevent the build-up of dust or water
particles.
5. If the radio is used in a harsh environment (such as driving rain, salt fog, etc.), it may be necessary to
periodically dry and clean the battery and radio contacts with a soft dry cloth or soft-bristle nonmetallic brush.
Figure 4-5: Universal Device Connector
29
14221-1800-2000, Rev. F
CAUTION
NOTE
For more rigorous cleaning, use the following procedure:
Do not use chemical cleaners, spray, or petroleum-based products. They may damage
the radio housing. We recommend using Chemtronics® Electro-Wash® PR (ES-1603) or
equivalent.
1. Apply the cleaning solution to a clean damp cloth and clean the radio.
Do not spray cleaning solution directly on radio. To clean the radio in the speaker and
microphone areas, carefully wipe these areas but prevent the cleaning solution from
entering the speaker or microphone openings.
2. Wipe off the radio with clean damp cloth using mild warm soapy water.
3. Follow up by wiping off the radio with clean damp cloth using warm water only.
Speaker Microphone, Premium, Fire, Noise Cancelling,
High Visibility Yellow
Microphone, Palm, 2-Wire, Black
12082-0650-01
XL-AE6G
Microphone, Palm, 2-Wire, Beige
12082-0650-02
XL-AE6M
Microphone, Mini-Lapel, 3-Wire, Black
12082-0650-03
XL-AE6H
Microphone, Mini-Lapel, 3-Wire, Beige
12082-0650-04
XL-AE6N
Earphone Kit, Black
12082-0650-05
Earphone Kit, Beige
12082-0650-06
Headset, In-Ear, Boom Mic, In-Line PTT
12082-0650-07
XL-AE2A
Headset, Light Weight, Over-the-Head, Single Ear, InLine PTT
Headset, Light Weight, Behind-the-Head, Dual Ear, InLine PTT
Headset, Light Weight, Behind-the-Head, Dual Ear, Pig
Tail PTT
Headset, Light Weight, Behind-the-Head, Dual In-Ear,
In-Line PTT
Headset, Light Weight, Behind-the-Head, Dual In-Ear,
Pig Tail PTT
Headset, Heavy Duty, Behind-the-Head, w/PTT
12082-0650-13
XL-AE1P
Headset, Heavy Duty, Over-the-Head, w/PTT
12082-0650-14
XL-AE1R
Headset, BTH Boom Mic, Earpiece, w/PTT
12082-0650-15
XL-AE2G
Headset, Tactical, Boom Mic, Earpiece, w/PTT
12082-0650-16
XL-AE1H
Skull Mic, w/Body PTT, Earcup
12082-0650-17
XL-AE1L
Throat Mic, w/Acoustic Tube, Body PTT
12082-0650-18
XL-AE1M
Throat Mic, w/Acoustic Tube, body and Ring PTT
12082-0650-19
XL-AE1N
CAUTION
4.6 OPTIONS AND ACCESSORIES
Only use Harris approved accessories. Refer to Harris’ Product and Services catalog for the complete list
of options and accessories available. Contact Harris for requirements not contained in this list:
Always use the correct options and accessories (battery, antenna, speaker/mic, etc.) for
the radio. Immersion rated options must be used with an immersion rated radio. Refer to
Table 4-1.
14221-2100-3000
14221-1100-8170 Radio Personality Manager 2 (RPM2) Software Release Notes
14221-7200-6130 BeOn Configuration and Use Feature Manual
Advanced Access Control and Radio Personality Manager Overview
Manual
32
14221-1800-2000, Rev. F
The product safety manual and the quick guide are included with the radio equipment package when the
radio ships from the factory. All publications listed above are available at www.pspc.harris.com
Information Center login and Tech Link.
via an
33
14221-1800-2000, Rev. F
CONTROL/INDICATOR
FUNCTION
Group/Channel Knob
Selects groups/channels.
Turn clockwise to power on radio and increase volume of audio heard from
missed calls due to a low volume setting.
A/B (Ø/O) Switch
User-programmable switch (see Section 7.4.2).
NOTE
5. BASIC OPERATION
5.1 XL-200P CONTROLS
Figure 5-1: XL-200P Controls
Table 5-1 describes the default functions of buttons, knobs, and controls. Most can be
programmed for different functions; see Section 7.4 for more information.
Table 5-1: XL-200P Controls, Indicators, and Connectors
Power/Volume Knob
34
speaker. Minimum volum e levels may be programmed into the radio to prevent
14221-1800-2000, Rev. F
CONTROL/INDICATOR
FUNCTION
When noise cancellation is enabled, the secondary and primary microphones are
for detailed information on using noise
cancellation.
User-programmable switch (see Section 7.4.3). By default, selects one of four
channel banks (see Section 5.12).
Used to select a comm only used function as an alter native to navigating m enus.
See Section 7.4.1 for the options that can be programmed to these buttons.
Push-To-Talk (PTT)
Button
Battery
Battery - Refer to Section 4.3 for battery connection and removal.
Antenna Connector
Antenna connector.
Used to place radio in emergenc y mode (see Section 5.32). This button can be
to do so.
Indicates radio status:
•Orange = actively transmitting encrypted.
Shows summary of radio operation, including channel/talkgroup (which can be
be configured for viewing from the front or rear of the radio. (Section 6.6).
Radio speaker which can be muted (Section 6.5). Adjust volume using the
Power/Volume knob.
When noise cancellation is enabled, the primar y and secondary microphones are
for detailed information on using noise
cancellation.
Front Display
Front display shows complete status and radio menus.
User-programm able dynamic keys that have their curr ent function labeled on the
can be programmed to these buttons.
From the Main Display, press this button to access the menu. Also selects
highlighted menu items.
Microphone
(Secondary)
A/B/C/D Switch
User-Programmable
Buttons
Emergency Button
Indicator Light Emitting
Diode (LED)
used together to form a dual microphone system. Noise c ancellatio n im proves th e
quality of transm itted voice. When no ise cance llation is disable d, onl y the primary
microphone is used. See Section
This is configured via prog ramming using Radio Persona lity Manager 2 (RPM2).
Press to transmit. Make sure Push-To-Talk (PTT) is enabled (Section 6.5).
disabled via progr amming using RPM2. In a ddition, this button can be used in
conjunction with a User-Program mable Button to clear emergencies if configur ed
• Red = actively transmitting.
• Green = actively receiving.
5.17
Top Display
Speaker
Microphone (Primary)
User-Programmable
Soft Keys
Menu/Select Button
color code d), as well as a v ariety of pr ogramm able icons. D isplay orient ation can
used together to form a dual m icr ophone s ystem. Nois e cancella tion im proves t he
quality of transm itted voic e. When noise cancellation is disab led, on l y the primary
microphone is used. See Section
radio display directl y above each button. See Section 7.4.1 for the opt ions that
5.8
35
14221-1800-2000, Rev. F
CONTROL/INDICATOR
FUNCTION
Navigates menu items.
display to display the functions assigned to
Press to end or reject an I-Call.
By default, used to enter text or numbers. Can be programmed for various
In addition:
Press while on the idle display to access Channel Information (see Section
Navigation Buttons
6.4).
Press while on the idle
programmable buttons (see Section 7.4).
Press to display Missed Call info.
Keypad
functions (see Section 7.4).
5.2 SOFT DTMF KEYPAD
The partial keypad model of the XL-200P supports a “soft” DTMF keypad. This allows the radio user to
utilize a graphical DTMF keypad in place of a physical DTMF keypad.
On screens that require keypad entry, press the KEYPAD softkey to display the keypad. Use , , ,
and to navigate, press the Menu/Select button to select highl ighted d igit, and then press the ENTER
softkey.
For example, when placing an Individual Call to a numeric address, the soft DTMF keypad can be used to
enter the address as shown:
Figure 5-2: Using the Soft DTMF Keypad
5.3 BEFORE FIRST USE
Make sure XL-200P has:
• Fully charged battery
• Antenna attached
• Personality and radio programmed using RPM2
• Encryption keys loaded if using encrypted channels
• Personality activated
36
14221-1800-2000, Rev. F
The radio can be programmed to require the entry of a PIN in order to operate the radio.
NOTE
NOTE
5.4 POWER ON AND SET VOLUME
The power switch and volume control are the same knob on top of the radio (see Figure 5-1). Turn the
Power/Volume Knob clockwise to power on XL-200P and increase the volume.
A minimum volume level can be programmed into the radio to prevent missed calls due
to a low volume setting.
Check with your System Administrator if you forget your PIN. As the PIN is entered, an
asterisk is displayed for each digit; the actual value is not displayed.
5.5 RADIO DISPLAYS
5.5.1 Top Display
The top display (Figure 5-3) shows a summary of status, such as channel number/bank, channel short
name, battery, scanning, and emergency mode. The display can be configured for viewing from the front
or rear of the radio (see Section 6.6). The channel short name is programmed using RPM2.
Figure 5-3: Top Display
37
14221-1800-2000, Rev. F
200P can be programmed to display the User ID on the System line of the
ICON
DESCRIPTION
ICON
DESCRIPTION
ICON
DESCRIPTION
(Blue)
Trunked Signal Strength
(Red)
TX Power
(Blue)
Bluetooth Connected
(Green)
Receive Signal Strength
(No Color)
Channel Idle
(Orange)
Transmitting Encrypted
Battery Level
100% Capacity
Battery Level
75% Capacity
NOTE
5.5.2 Front Display
Figure 5-4 shows a sample front display while on the idle screen. The idle screen appears after power up
or after exiting from the menus.
Figure 5-4: Sample Idle Front Display
The XLdisplay.
Table 5-2 describes some of the icons that may be displayed by the XL-200P. The radio menu also
contains an icon glossary in the Utility Menu (see Section 5.8). Icons and their location can be
customized using RPM2.
Table 5-2: Radio Icons
Battery Fully Charged
Bluetooth Enabled
Encryption Enabled
Global Encryption
OTAR Disabled
OTAR Registered
OTAR Registering
Monitor On
VDOC
Receiving Data
Transmitting Data
Alert(s) Present
Vote Scanning
Scanning Enabled
38
OTAR Rekeying
Emergency
14221-1800-2000, Rev. F
ICON
DESCRIPTION
ICON
DESCRIPTION
ICON
DESCRIPTION
Battery Level
50% Capacity
Battery Level
25% Capacity
Battery Level
(Low Battery Audio Indicator)
Battery Level
(RX-Only State)
Conventional Site
Unregistered
Conventional Site
Registered
LTE – Registered
Foreign Network
LTE – Denied or Unknown
Registration Status
5% Capacity
Battery Exhausted
Battery Charging
Talkaround Enabled
Failsoft
LTE – Registered Home
Transmit Power Level High
Transmit Power Level Low
RX Only
Speaker Muted
TX Disabled
Tones Disabled
PTT Disabled
LTE – No Signal
RX Mail
Noise Cancellation Enabled
Fire Speaker Mic Attached
Nuisance Channel
Type 99 Enabled
GPS Tracking
Wi-Fi Clients Connected
39
14221-1800-2000, Rev. F
5.6 MANDOWN
If enabled via radio programming, the following conditions can be configured to trigger a Mandown
condition:
• MOTION - Mandown is declared with lack of motion.
• TILT - Mandown is declared when the radio is tilted.
• BOTH - Mandown is declared by radio tilting and lack of motion.
This can be useful if, f or example, a radio user is in danger and has not moved for a certain amount of
time. If the user’s movement falls below the confi gured le vel
, then a tone begins playing. An Emergency
is declared on the channel/group based on the radio’s Emergency configuration.
5.7 STATUS MESSSAGES
The radio may display various radio Status Messages during operation. These messages are described in
Table 5-3.
Table 5-3: Status Messages
MESSAGE DESCRIPTION
PTT DENIED
CALL QUEUED P25 Trunked and EDACS - The system has placed the call in a request queue.
SYSTEM BUSY
SCANNING The radio is scanning.
TX EMERGENCY An em ergency call is being transmitted.
RX EMERGENCY An emergency call is bei ng recei ved. The radio dis pl ays the unit name or unit ID.
WIDE AREA SC AN
INVALID TALKGROUP
INVALID UNIT P25 Trunked and EDACS - The current unit is not valid for the current system.
REGISTERING
P25 Trunked and EDACS - The radio or talkgroup is not authorized to operate on the selected
system and/or talkgroup.
P25 Trunked and EDACS - The system is busy, no channels are currently available, the queue is
full, or an individual call is being attempted to a radio that is currently transmitting.
P25 Trunked and EDACS - The radio has entered the Wide Area Scan mode to search for a new
system.
P25 Trunked and EDACS - The current talkgroup is not valid for the current system. This could
happen if the site denies registration due to an unrecognized talkgroup ID.
P25 Trunked only - Displayed when the radio is performing a registration/affiliation on a P25
trunking site.
P25 Trunked and EDACS - The control channel is lost and the radio has entered the Control
Channel Scan mode to search for the control channel (usually out of range indication).
P25 Trunked and EDACS - Only displayed if the system is configured for "EnhancedCC" mode of
operation. When the radio cannot find a Control Channel in either the trunked frequency set or the
list of discovered adjacencies, the radio is able to perform a full spectrum frequency scan to find a
new Control Channel.
P25 Modes and EDACS - Another user has tried to call or page this radio. The user can view who
the caller was by pressing the key.
40
14221-1800-2000, Rev. F
The Custom predefined menu layout allows the administrator to customize the list of
CUSTOM
(Default Settings)
Call Menu
Exit Emergency
Talkaround
Individual Call
Change Talkgroup
Call Alert/Page
Channel Guard
Audio Playback
Tone Encode
T99
Audio Settings
Display Settings
GPS Settings
Clock Settings
Bluetooth Settings
Scan Menu
Enable/Disable Scan
View Scan List
Edit Zone Scan List
View Custom Channels
Edit Custom Scan List
Custom Scan
Site Roam
Security Menu
Encryption Enable
Zeroize
Global CKR Enable
GCKR Key Select
Active Key Set
Key List
OTAR Enable
OTAR Rekey
NOTE
5.8 PREDEFINED MENU LAYOUTS
Depending on radio programming, some menu options described in this manual may not be available.
The XL-200P supports three predefined menu layouts: Full, Custom, and Restricted. Table 5-4 details
what is available in each layout:
menu items that are available to the radio user. Table 5-4 lists the default settings.
Table 5-4: Predefined Menu Layouts
MENU FULL
RESTRICTED
41
14221-1800-2000, Rev. F
CUSTOM
(Default Settings)
Message Menu
Radio Status
Radio Message
Textlink Messages
Textlink Forms
Textlink Mailbox
Faults
Program Menu
Activate Plan
Activate Profile
Maintenance Menu
Radio Info
Battery
TCXO Tuning
P25 Tests
RSSI Display
Phase II Display
Feature Info
WiFi Access Point
Change Language
Change PIN
Icon Glossary
Install GPP Software x
Zone
TOP-LEVEL
MENUS
TALKAROUND MODE
Enable/disable talk-around. See Section 5.23 for more information.
TYPE 99 TOGGLE
Enable/disable T99. See Section 5.24 for more information.
TONE ENCODE
Analog conventional only - Transmits a programmed tone sequence on the current
radio system and channel. See Section 6.19 for more information.
information.
CALL ALERT
Select a group for Call Alert transmission. See Section 5.25.
CHANNEL GUARD
Select the Transmit and/or Receive Channel Guard tone. See Section 5.22.
AUDIO PLAYBACK
Replays the last recorded call. See Section 5.27 for more information.
MENU FULL
RESTRICTED
5.9 MENU
Press the Menu/Select button while on the idle display to access the menu. Press the or buttons to
navigate the top-level menus, and press the or buttons to navigate the sub-menus. Refer to Figure
5-1 for button location. While in a menu, press the Menu/Select button to choose, activate, or toggle the
selected item; similar to an enter key. Table 5-5 provides a high-level overview of the menu layout.
Menu options on your radio may vary depending on available features and radio programming.
EXIT EMERGENCY Exits emergency. See Section 5.32 for more information.
CALL
INDIVIDUAL CALL
CHANGE TLKGRP Change the selected talkgroup. See Section 5.14.
Table 5-5: Menu Navigation
SUB-MENUS DESCRIPTION
Allows you to select an individual for an individual call. See Section 5.15
for more
42
TOP-LEVEL
MENUS
SCAN
SCAN LISTS
View/Edit available scan lists. See Section 6.14.
ASSIGNED CUSTOM LIST
Create, View, and Edit Custom Scan Lists. See Section 6.14.6.
ZEROIZE KEYS
Removes all encryption keys from the radio. See Section 6.20.2.
ENCRYPTION
Enable/Disable encryption. See Section 5.20.
GLOBAL ENCRYPTION
Enable/Disable Global Encryption. See Section 6.20.4.
Select the Global Key. Only available if Global Encryption is Enabled. See Section
ACTIVE KEYSET
Select the Active Keyset. See Section 6.20.5.
KEY LIST
View available key lists. See Section 6.20.6.
OTAR
Enable/disable Over-the-Air Rekeying (OTAR). See Section 6.20.7.
OTAR REKEY
Request that the KMF updates the keys in the radio. See Section 6.20.7.
Used to send a particular message to the site without making a voice call. See
TEXTLINK MESSAGES
Allows the user to send a Radio TextLink message. See Section 6.17.
TEXTLINK FORMS
Allows the user to send a Radio TextLink form. See Section 6.17.
TEXTLINK MAILBOX
FAULTS/ALERTS
Displays radio faults and alerts. See Section 6.18.
AUDIO SETTINGS:
• SPEAKER (MUTE/UNMUTE)
Mute or unmute the speaker audio.
• NOISE CANCELLATION
Enable or disable Noise Cancellation. See Section 5.17.
• TONES
Enable or disable radio side tones.
• KEYPAD TONES
Enable or disable tones that sound when the radio’s keypad buttons are pressed.
DISPLAY SETTINGS:
Press the Menu/Select button to toggle the front and top display’s COLOR
INVERTED).
ON/OFF/MOMENTARY/MOMENTARY (OFF).
• FRONT BRIGHTNESS
Press or to dim or brighten the display.
• FRONT TIMEOUT
When the FRONT BACKLIGHT setting is MOMENTARY, this value specifies how
• FRONT DISPLAY OFF
Turns the front display off completely. Press the Menu/Select button to turn the
front display back on.
• TOP BACKLIGHT
Press the Menu/Select button to toggle the top display backlighting
ON/OFF/MOMENTARY.
• TOP BRIGHTNESS
Press or to dim or brighten the display.
• TOP TIMEOUT
When the TOP BACKLIGHT setting is MOMENTARY, this value specifies how
Press or to change the time in 0.5 second increments.
• TOP ORIENTATION
Set orientation of top display to be viewed from radio: FRONT, BACK, or AUTO.
be viewed from the front.
• INDICATOR LED
Press the Menu/Select button to toggle the indicator LED ON or OFF.
14221-1800-2000, Rev. F
SUB-MENUS DESCRIPTION
START SCAN/STOP SCAN Start or stop scan operation. See Sections 5.28 and 5.29.
SITE ROAMING Enable/Disable Wide Area System Scan. See Section 6.14.7.
SECURITY
MESSAGES
GLOBAL KEY
RADIO STATUS
RADIO MESSAGE
• PTT
• COLOR SCHEME
• FRONT BACKLIGHT
6.20.4.
Used to send a particular status condition to the site without making a voice call.
See Section 6.15.
Section 6.16.
Contains received Radio TextLink messages. See Section 6.17.
Enable or disable Push-To-Talk (PTT). Disable PTT to prevent accidental keying,
such as when radio is in the holster or you are getting into a car.
SCHEME for optimum visibility in day or night conditions (NORMAL or
Press the Menu/Select button to toggle the front display backlighting between
UTILITY
long the radio needs to be inactive before the front display’s backlight turns off.
Press or to change the time in 0.5 second increments.
long the radio needs to be inactive before the top display’s backlight turns off.
When AUTO is selected, the radio changes the top display to be viewed from the
back if an external microphone or speaker is attached. Otherwise, the display can
43
14221-1800-2000, Rev. F
TOP-LEVEL
MENUS
BLUETOOTH:
• ENABLED (YES/NO)
Enable/disable Bluetooth. See Section 6.10 for more information.
CLOCK SETTINGS:
• TIME FOR MAT
Select 12 or 24 hour time display format.
• TIME ZONE
Set time zone relative to Universal Time Coordinated (UTC).
• GPS (ENABLED/DISABLED)
Enable/disable GPS.
• POSITION INFO
Displays GPS, Latitude, Longitude, and Altitude information. From this menu, click
NEXT to access SA INFO (see Section 6.2).
• ANGULAR UNITS
Set unit of measurement of displayed angular units: CARDINAL, DEGREES, or
MILS.
• LINEAR UNITS
Set unit of measurement of displayed linear units: STATUTE, METRIC, or
NAUTICAL.
(MGRS), or Universal Transverse Mercator (UTM).
PROGRAM:
• ACTIVATE PLAN
View/Activate a personality. See Section 6.1.
• PROFILES
Change current profile. See Section 5.16.
MAINTENANCE:
• RADIO INFO
Displays radio information, i.e., ESN, software revisions, and firmware revisions.
• TESTS
Allows service personnel to run radio tests.
• PH2 LC DISPLAY
For field service use only.
display. -130 dBm is displayed when there is no received signal.
For field service personnel only. Improper adjustment will result in loss of
• FEATURE INFO
Displays what features are enabled on your radio.
WIFI ACCESS POINT:
• POWER
Power Wi-Fi On/Off.
When the radio is configured as a Wi-Fi access point, displays the number of
connected clients.
LTE:
Signal Strength:
• Registration Status:
Indicates whether or not you are registered (connected) to the LTE network.
NGLM:
Displays the Next Generation LTE Module’s software revision.
Displays the International Mobile Equipment Identity. The IMEI is used to identify
devices on a network.
cellular networks.
INSTALL GPP SOFTWARE:
Select a GPP package to install.
CHANGE LANGUAGE
Press the Menu/Select button to toggle between available languages.
CHANGE PIN
Allows you to change your PIN.
ZONE
View or change zones/systems (see Sections 5.11 and 6.3.1).
SUB-MENUS DESCRIPTION
• PAIRING MGMT Pair Bluetooth devices with the radio. See Section 6.10 for more information.
GPS SETTINGS:
UTILITY
(Continued)
• POSITION FORMAT
• BATTERY INFO
• DISPLAY RSSI
• TCXO TUNING
• CLIENT COUNT
• PLMN (MCC/MNC):
•
•
• IMEI:
Set format of displayed position information: Latitude/Longitude Degrees Minutes
Seconds (LAT/LONG DMS), LAT/LONG DM, Military Grid Reference System
When a smart battery is attached, displays detailed battery status information.
When a regular battery is attached, displays battery voltage.
When enabled, RSSI is displayed on the RSSI screen and in the bottom of the idle
communications.
Displays the Public Land Mobile Network (Mobile Country Code/Mobile Network
Code).
Displays the LTE signal strength.
• IMSI:
ICON GLOSSARY Defines icons displayed by the radio.
Displays the International Mobile Subscriber Identity. The IMSI is used to identify
the user of a cellular network and is a unique identification associated with all
44
14221-1800-2000, Rev. F
5.10 ALERT TONES
The XL-200P pr ovides audible Alert Tones or “beeps” to indicate various operating conditions. Some of
the most common tones are described in Table 5-6.
TONE DESCRIPTION SOUND/DURATION
Table 5-6: Alert Tones
Ready To Talk Tone
Unencrypted (Analog FM or
P25 digital)
Ready to Talk Tone
Encrypted P25 digital
PTT Denied
Maximum transmit duration
expires
Low Battery Alarm
Emergency Call Received Radio is receiving an emergency call or priority call.
After a PTT is pressed, this is an audible indication (tone) for
you to begin speaking into the microphone.
After a PTT is pressed, this is an audible indication (tone) for
you to begin speaking into the microphone.
PTT not possible. Momentary tone is present:
• Receive only
• Key not found
• PTT button disabled
• Emergency button disabled
• Emergency not supported for current channel
• Clear transmit denied
• Trunking Channel unavailable
Maximum transmit duration is exceeded.
Alarm sounds upon initial detection of low battery and every
30 seconds thereafter. Tone stops upon detection of a battery
charging state.
1000 Hz tone for 25 ms
1200 Hz tone for 25 ms
544 Hz tone for 75 ms
5 beeps of 2400 Hz tone and
then a 544 Hz tone for as long
as PTT is pressed
Sequence of tones:
• 937 Hz tone for 50 ms
• Silence for 60 ms
• 1300 Hz tone for 50 ms
600 Hz tone for 250 ms and
1800 Hz tone for 250 ms
Out of Range Radio fails to find a local control channel.
5.11 SELECT ZONE/SYSTEM
A System is a group of channels or talkgroups that share a common set of parameters as programmed
using RPM2. For example, a Trunking system defines the parameters needed to communicate on a
particular infrastructure by agency or geographical region, such as WACN, System ID, Talkgroups, etc. A
conventional system defines the channel set used and any specific signaling attributes (See RPM2 for
more information on System attributes). Systems are designated by the XX icon in the Zone/System
menu.
A Zone is an OPTIONAL container that can hold channels or talkgroups from a variety of systems (see
Section 6.3.2). In other words, each member of a Zone belongs to an underlying system. (See RPM2 for
Programmable via RPM2:
• Disabled (no tone)
• Slow (tone every 15s)
• Medium (tone every 10s)
• Fast (tone every 5s)
• Tones is 544 Hz tone for 75
ms
45
14221-1800-2000, Rev. F
The currently selected
may be held to scroll repetitively, and the menu will wrap to allow quick
Select the desired zone/system using the Menu/Select button.
more information on Zone attributes). Zones are always listed first in the Zone/System menu and are
designated by the icon. A button on the radio can be programmed to scroll through available
zones/systems (see Section 7.4).
Or
To select a zone/system via the menu:
1. Press the Menu/Select button to access the menus.
2. Use or to display the ZONE menu.
zone/system will be highlighted. A personality can have up to 512 systems
and up to 50 Zones, independent of banks or channels.
3. Use or to highlight the desired zone/system. The and buttons
access to a particular zone/system,
4. Press the VIEW ZONE soft key to view channels in the zone/system, or
46
14221-1800-2000, Rev. F
various options that can be programmed to the radio buttons
NOTE
5.12 SELECT GROUP/CHANNEL AND BANK
The XL-200P can be programmed with 1,250 talkgroups or 1000 channels per personality. Use the
Group/Channel knob to select groups/channels 1 - 16. Use the A/B/C/D switch to set the bank. The
selected bank is indicated on the display.
• Bank A: Channel A1 - A16 (1-16)
• Bank B: Channel B1 - B16 (17-32)
• Bank C: Channel C1 - C16 (33-48)
• Bank D: Channel D1 - D16 (49-64)
If your system has more than 64 groups/channels, a button on the radio can be programmed for the SEL
CHAN/GRP option. This allows you to select a “super bank,” providing access to groups/channels
beyond the first 64.
Note that ZONES have a limit of 64 entries per zone and cannot be “superbanked.”
Direct Channel Entry
A button on the radio can be programmed for Direct Channel Entry, which allows the user to enter the
talkgroup/channel number directly from the keypad.
The radio can be programmed for one of the following Direct Channel Entry options:
• When a Zone is selected on the radio, Direct Channel Entry performs a lookup using the currently
selected system’s group list
Or
• When a Zone is selected on the radio, Direct Channel Entry performs a lookup using the currently
selected Zone’s system/group list.
5.13 LOCK/UNLOCK KEY PAD
There ar e two levels of keypad lock available. Keypad lock and Radio lock. Keypad lock only locks the
navigation keys (except for use in unlock), programmable softkeys, and DTMF keypad. Radio lock
disables all physical keys and knobs except:
• The 4-position switch
• PTT
• Emergency Button
• Any User Programmable Button (UPB) programmed for Monitor/Clear. (This is required to allow
Monitor/Clear to function for 2-button emergency clear.)
The A/B switch , ABCD switch, or a button on the radio can be programmed to lock the keypad/radio. If
the keypad was locked via a switch, moving the switch to another position will unlock the keypad. If
locked via a button, the navi gation keys must be used to enter the unlock sequence of Left, Right, Up
Down.
See Section 7.4 for the
and switches.
47
14221-1800-2000, Rev. F
To transmit a group call:
the talkgroup for the selected channel may be
ress the Menu/Select button to access the main
menu.
and press the
After selecting the new talkgroup, the radio returns to
Receiving a group call:
5.14 GROUP CALLS
5.14.1 Transmit a Group Call
A talkgroup is a group of radios that you want to have private conversations with. These groups can be
divided into areas such as state, region, county, or large special events. A group call can only be made on
digital channels.
Turn the Channel/Group knob to select the desired group (see Figure 5-1). Press PTT to transmit.
Or
A button on the radio can be programmed for DIRECT CHANNEL ENTRY to allow the user to enter the
talkgroup/channel number. Press PTT to transmit.
Or
1. In P25 Conventional,
overridden as follows: P
2. Press or to display the CALL menu.
3. Press or to highlight CHANGE TLKGRP and press the Menu/Select
button.
4. Press or to highlight and the desired talkgroup
Menu/Select button.
the main screen.
5. Press PTT to transmit.
5.14.2 Receive a Group Call
When receiving a group call, the status area of the idle display toggles between
the Unit Name and the Group Name of the transmitting radio. Note that if either
of those names is not programmed the corresponding ID number is displayed.
48
14221-1800-2000, Rev. F
To transmit an ind iv id ual call:
1. Press Menu/Select button to access the main menu.
to highlight the unit to call and press the Menu/Select button,
When transmitting an Individual Call, the radio
displays the called radio’s name or Unit ID. If the radio is programmed for
Acknowledged Individual Call, the radio displays “CALL QUEUED” until
How long the radio remains in Individual Call mode with no activity is programmable.
Receiving an individual call:
the radio displays the calling radio’s
), change
5.15 INDIVIDUAL CALLS
An individual call is used to make a call to one radio as opposed to a group of radios. An individual call
can only be made on a digital channel.
5.15.1 Transmit an Individual Call
2. Press or to display the CALL menu.
3. Press or to highlight INDIVIDUAL CALL and press the Menu/Select
button.
4. Use or
or select KEYPAD to enter the Unit ID.
5. Press PTT to make the call.
the callee answers or rejects the call.
6. After the callee answers, press PTT to respond.
7. Press to end the call.
5.15.2 Receiving an Individual Call
1. When receiving an Individual Call,
name or Unit ID. The radio will also display “Press to END.”
2. Press PTT to respond or to END/REJECT the call. How long the radio
remains in the Individual Call mode with no activity is programmable.
3. The radio rings and indicates a missed call if you do not respond. The ring
sounds until you press PTT, view the missed call menu (
channel/group/system, or power cycle the radio.
4. On the missed call screen, press the DISMISS soft key to clear the entry.
49
14221-1800-2000, Rev. F
To change the currently selected Profile:
1. Press the Menu/Select button to access the menu.
5. Press or to select the desired Profile and press the Menu/Select button.
NOTE
5.16 PROFILES
The XL-200P supports User Profiles. A User Profile is a grouping of preset configurations that allow the
user to change radio operation based on current activity/scenario. For example, the radio can be
programmed profiles named Noisy, Fire, etc., and the radio user can switch profiles on the radio
depending on the environment they are entering. User Profile selection persists across system/group
changes and power cycles. Up to 10 profiles can be programmed to the XL200P. When you activate a
new personality, the selected Profile changes to None.
A "Covert" Profile is installed on the XL-200P by default. This profile cannot be modified or deleted.
The following attributes apply when the Covert profile is active:
• The speaker is enabled.
• All tones are disabled.
• Keypad tones are disabled.
• Voice Annunciation is disabled.
• The front display backlight is disabled
• The top backlight is turned off.
• The indicator LED is disabled.
• All other attributes remain at their current value.
2. Press or until the UTILITY menu is displayed.
3. Press or to highlight PROGRAM and press the Menu/Select button.
4. Press or until the PROFILES menu is displayed.
A profile change persists across system/channel changes, and power cy cles.
A button on the radio keypad can be used to toggle profiles. See Section 7.4.1.
50
14221-1800-2000, Rev. F
To enable Noise Cancellation:
1. Press the Menu/Select button to access the menu.
and press the
Toggle Noise
5.17 NOISE CANCELLATION
The XL-200P features Harris’ proprietary noise suppression capability to provide clear and crisp voice
quality in high-noise environments. This can be used in any mode, including analog and digital
communications.
The XL-200P has three microphones; two located at the top of the radio (primary) and one on the bottom
(secondary). When noise cancellation is enabled, voice is picked up by the upper left microphone, and
noise is picked up from the bottom microphone.
In the case where noise cancellation is enabled and a speaker microphone is attached to the XL-200P, talk
into the speaker microphone. In this mode, XL-200P top left microphone is used to pick up the
surrounding noise, and the other microphones are unused. See Section 5.17.4 for more information. If the
bottom (secondary) microphone is blocked, the XL-200P operates as though noise cancellation is turned
off.
5.17.1 Enable Noise Cancellation
2. Press or until the UTILITY menu is displayed.
3. Press or to highlight AUDIO SETTINGS
Menu/Select button.
4. Press or to highlight NOISE CANCELLATION.
Cancellation ENABLED/DISABLED using the Menu/Select button.
Refer to Section 6.5 for more information on the Audio Settings menu.
5.17.2 Using Noise Cancellation
When using the noise cancellation feature, observe the following:
• Verify NOISE CANCELLATION is enabled (see Section 5.17.1).
• Talk within two (2) inches of the primary microphone (see Figure 5-5).
• Ensure the primary and secondary microphones are not covered. See Section 5.17.4 for more
information on the primary and secondary microphones.
• Speak clearly, loudly, and with authority.
• In very noisy environments, it is o.k. to yell into the radio. The radio can handle loud input levels.
51
14221-1800-2000, Rev. F
Figure 5-5: Using Noise Cancellation
5.17.3 The Effect of Distance from the Microphone
Unlike a normal microphone system, noise cancellation makes the level of your voice diminish quickly as
you move away from the radio. In essence, the radio starts to see your voice as surrounding noise.
Whereas, you may be comfortable speaking up to a foot away under normal operation, noise cancellation
requires that you hold the radio close.
5.17.4 Primary versus Secondary Microphone
5.17.4.1 Without a S peaker Microphone Attached
The primary microphone is located on top of the radio and the secondary is on the bottom of the r adio
(refer to Figure 5-1 for microphone locations).
5.17.4.2 With a Speaker Microphone Attached
When a speaker microphone is attached, the radio electronically switches over to use the radio’s top left
microphone as secondary. The microphone on the attached speaker microphone becomes primary.
5.17.5 When using an SCBA Mask
When using an SCBA mask, the primary microphone can be held directly against the voice port. If the
SCBA has a voice amplifier, the same rule applies. Ensure that the secondary microphone is uncovered. If
possible, point the secondary microphone toward the noise source.
5.18 PTT OPTIONS
The radio can be programmed via RPM2 with one of the following PTT options:
• Radio and Accessory - In this mode, when the radio is PTT’d the audio source will correspond with
the PTT source.
If the source of PTT is radio, the audio is routed via the radio microphone.
52
If the source of PTT is an external microphone accessory, the audio is routed via the external
microphone accessory.
• Accessory Only - Any PTT input will have the audio routed through the external microphone
accessory.
14221-1800-2000, Rev. F
Turn encryption on or off via the Security Menu:
1. Press the Menu/Select button to access the menus.
. Toggle encryption
enabled/disabled using the Menu/Select button. This option is grayed out if
is programmed for encryption, or if Encryption Mode in the
radio’s personality is programmed “Forced On.”
NOTE
NOTE
The Bluetooth Speaker Mic is unaffected by this setting. PTTing the Bluetooth Speaker
Mic always results in audio being routed via the Bluetooth Speaker Mic.
5.19 VOICE ANNUNCIATION
When enabled via programming, Voice Annunciation provides audible feedback for various radio
operations. The radio can be programmed to play an audio message for any or all of the following. This
message can be a pre-recorded (canned) message or a user-recorded message.
• Zone changes
• Channel changes
• System changes
• Encryption On/Off
• Noise Cancellation On/Off
• Scan On/Off
• Talkaround On/Off
• Monitor Mode On/Off
• 2 or 4 Position switch change
For more information on configuring the radio for Voice Annunciation, refer to the Voice Annunciation
Feature manual 14221-7200-6110.
5.20 ENABLE/DISABLE ENCRYPTION
A switch or a button on the radio can be programmed to enable/disable encryption.
See Section 7.4 for the various options that can be programmed to the radio buttons
and switches.
Or
2. Use the or button to highlight and select the SECURITY menu.
3. Use the or button to highlight ENCRYPTION
any switch
• If a channel is programmed to be encrypted, an optional key icon appears on the main display when
encryption is enabled. The system must also be programmed for encryption.
• When encryption is enabled and you use any channel not configured for encryption, the radio allows
PTT. The signal is transmitted unencrypted.
53
14221-1800-2000, Rev. F
for the various options that can be programmed to the radio buttons
To select the Channel Guard tone:
1. Press Menu/Select button to access the main menu.
TRANSMIT GUARD
6.4 and 7.2 for more information.
NOTE
NOTE
• Systems configured for Global Encryption (enabled in the Security menu) can display an optional
Global Encryption icon in addition to or instead of a key icon (Section 6.20.3).
5.21 TRANSMIT EN ABLE/ DISABLE
When transmit is disabled, all forms of transmission from the radio are disabled, including Bluetooth.
This is designed for use in explosive atmosp here s.
If enabled via programming, use the A/B switch to enable or disable transmit.
See Section 7.4
and switches.
5.22 CHANNEL GUARD (ANALOG CONVENTIONAL ONLY)
Channel Guard is Harris’s trademark for CTCSS (tone squelch) and CDCSS (digital tone squelch).
The Channel Guard menu is only accessible if the System is setup for CG SEL in the
radio’s personality.
2. Use or to display the CALL menu.
3. Use or to highlight CHANNEL GUARD and press the Menu/Select
button.
4. Use or to highlight RECEIVE GUARD or
and press the Menu/Select button.
5. Use or to highlight the desired option from the list and select using the
Menu/Select button.
6. The Channel Guard frequency is displayed on the main display.
The Channel Info screen and Channel Edit screen will change depending on this selection. See Sections
54
14221-1800-2000, Rev. F
A button on the radio can be programmed for Channel Guard Override (see Section
To enable talkaround:
1. Press Menu/Select button to access the main menu.
Talkaround icon appears. Calls are now made on the receive
menu. Power
NOTE
NOTE
7.4).
5.23 USE TALKAROUND TO BYPASS REPEATER (ANALOG AND P25
CONVENTIONAL ONLY)
You can bypass the repeater system to communicate directly with other radios on your current channel’s
receive frequency. This is useful if you are out of range of a repeater or if a repeater is busy. You will
need to be in range of the other radio.
2. Press or to display the CALL menu.
3. Press or to highlight TALKAROUND MODE.
4. Press the Menu/Select button to toggle TALKAROUND MODE to
ENABLED.
5. The optional
frequency until you disable talkaround mode via the CALL
cycling the radio does not disable talkaround.
Or
A button or switch can be programmed to toggle talkaround enable/disabled. See Section 7.4 for the
various options that can be programmed to the radio buttons and switches.
If the Talk-Around Indication feature is enabled using RPM2, the radio will play a unique grant tone
when a call is placed on a simplex channel or when Talk-Around has been enabled on a duplex
channel. This feature applies to both Analog and P25 Conventional systems. It optionally allows the
radio to also play the same tone when it receives a call while operating in simplex or Talk-Around. If
configured, the radio plays the tone at the selected volume level.
The tone will not play on systems configured with MDC.
Talk-Around Indication can be specified for each individual Analog and P25 Conventional system
configured in personality. The following options can be selected, and apply only when the radio is on a
simplex channel or when Talk-Around has been enabled by the user:
• Disabled: (This is the default option.) When this option is selected, the radio plays the standard grant
tone when a call is placed. The radio does not play a tone when a call is received.
55
14221-1800-2000, Rev. F
In the radio personality, the “Alert Tone” parameter needs to be enabled for each
To enable Type 99:
1. Press Menu/Select button to access the main menu.
is displayed in the top of the radio display when Type 99 is enabled.
NOTE
• Transmit Only: When this option is selected, the radio plays a different “Talk-Around” grant tone
when a call is placed. The radio does not play a tone when a call is received.
• Transmit & Receive: When this option is selected, the radio plays a different “Talk-Around” grant
tone when a call is placed, and at the beginning of a received call.
channel on the Conventional Frequency Set. The “Ready To Talk Tone” parameter
must also be enabled for the Talk Around Indication tone to be played when the radio
is keyed.
5.24 TYPE 99 OPERATION
Type 99 is Harris' name for in-band, two-tone sequential signaling. It is a conventional signaling protocol
used to control the muting and unmuting of a radio. This signaling is commonly used for selective calling
of individual units or groups of units in a conventional system.
In Type 99 tone systems, calls are not heard until the radio detects the proper two-tone sequence. This, in
conjunction with squelch, prevents the user from hearing noise or undesired conversations. When the
radio detects the second tone, it sounds the appropriate Type 99 alert tone. After the second tone stops,
the receiver audio path is opened in order for the user to receive messages.
5.24.1 Enable/Disable Type 99
2. Press or to display the CALL menu.
3. Press or to highlight T99 TOGGLE.
4. Press the Menu/Select button to change T99 TOGGLE between ENABLED and DISABLED. T99
Or
A button or switch can be programmed to enable/disable Type 99 (see Section 7.4).
5.24.2 Disable After PTT
If this option is programmed using RPM2, Type 99 is disabled after the radio user activates the PTT. This
allows the radio user to monitor traffic on the channel (after a PTT action) without pressing the monitor
button.
Can be used in conjunction with the “Auto Reset” option (see Section 5.24.3) to disable Type 99 after a
PTT and automatically reset, or enable, Type 99 after 30 seconds.
5.24.3 Auto Reset
If this option is programmed using RPM2, Type 99 is automatically reset, or turned back on, after 30
seconds. Can be used in conjunction with the “Disable After PTT” option (see Section 5.24.2) to disable
Type 99 after a PTT and automatically reset, or enable, Type 99 after 30 seconds.
56
14221-1800-2000, Rev. F
To send an alert:
1. Press the Menu/Select button to access the main menu.
and press the Menu/Select
to highlight the desired unit from the list and press the
5. Press PTT to send the page.
NOTE
5.25 CALL ALERT (PAGE)
5.25.1 Send Alert
2. Press or to display the CALL menu.
3. Press or to highlight CALL ALERT
button.
4. Press or
Menu/Select button, or select KEYPAD to enter the Unit ID.
5.25.2 Receive Alert
1. When receiving a Call Alert, the radio displays the calling radio’s name or Unit ID.
2. The radio rings and indicates a missed call. The ring sounds continuously until you press PTT, press
the CLR MISSED softkey, change group/system, or power cycle the radio.
5.26 DTMF
The XL-200P supports the transmission of DTMF tones corresponding to the numbers/characters on the
keypad. To overdial numbers/characters, press and hold the PTT button, and then press the corresponding
keys one at a time on the keypad. Valid keys for DTMF tones are: 1, 2, 3, 4, 5, 6, 7, 8, 9, *, 0, and #.
For conventional or P25 Conventional systems, DTMF tones only play if the current
system is programmed for DTMF (part of general System configuration). DTMF tones
are always enabled for P25 Trunking systems.
5.27 AUDIO PLAYBACK
The Audio Playback feature allows the user to playback a previously received call. Recordings are stored
in the radio’s RAM and are not persistent across power cycles. The radio stores the last five (5) recorded
calls up to 1 minute each.
A button on the radio can be programmed to replay the last recorded call. To playback the last received
call from a button:
1. Press the button programmed for audio playback. The last call received before the button was pressed
is played each time the button is pressed.
2. Additional incoming calls will be recorded in the background, but pressing the button continues to
replay the captured call until reset.
57
14221-1800-2000, Rev. F
To playback a previously received call from the menu:
1. Press the Menu/Select button.
and press the
4. Press the BACK soft key to exit the scan menu.
NOTE
3. To reset the feature and allow a new call to be captured, press and hold the button until you hear a 2-
tone chirp. At this point the button can be used to capture an new incoming call.
You can also playback one of the last five calls received via the menu.
2. Press or to display the CALL menu.
3. Press or to highlight AUDIO PLAYBACK
Menu/Select button.
4. Select the desired call from the list (the most recent call is at the top of the
list) and press the select button. The selected call will be played.
• If a button is also programmed for Audio Playback, pressing the button
replays the call that selected in the menu. The feature must be reset as
above in order to use the button to capture a new call.
• If a button is not programmed for Audio Playback, then you must
navigate back to the menu to play the call again.
Any incoming call that occurs during playback preempts the playback.
5.28 START S CAN
This procedure assumes that the scan list has been added and the radio is not in active scan. Refer to
Section 6.13 f or sc an se tup o r Section 5.29 for stopping scan. Refer to Section 6.14.1.1, Section 6.14.1.2,
and Section 6.14.1.3 for home and priority channel descriptions.
To start scan:
1. Press the Menu/Select button to access the main menu.
2. Press or to display the SCAN menu.
3. Press or to highlight START SCAN and press the Menu/Select button.
START SCAN text changes to STOP SCAN.
5. The scan icon is displayed on the idle display when scanning is enabled.
58
14221-1800-2000, Rev. F
To start scan:
1. Press the Menu/Select button to access the main menu.
for the various options that can be programmed to the radio buttons
To stop scan:
1. Press the Menu/Select button to access the main menu.
NOTE
NOTE
Or
2. Press or to display the SCAN menu.
3. Press or to highlight SCAN LISTS and press the Menu/Select button.
4. Press or to highlight the desired SCAN LIST and press the START
SCAN soft key.
Or
A switch or button on the radio can be programmed to start/stop scan.
If a switch is programmed for start/stop scan, the menu for starting and stopping scan
is disabled.
See Section 7.4
and switches.
5.29 STOP SCAN
2. Press or to display the SCAN menu.
3. Press or to highlight STOP SCAN and press the Menu/Select button.
4. Press the BACK soft key to exit the scan menu.
59
14221-1800-2000, Rev. F
To stop scan:
1. Press the Menu/Select button to access the main menu.
starting and
for the various options that can be programmed to the radio buttons
NOTE
NOTE
NOTE
Or
2. Press or to display the SCAN menu.
3. Press or to highlight SCAN LISTS and press the Menu/Select button.
4. Press the STOP SCAN soft key.
Or
A switch or button on the radio can be programmed to start/stop scan.
If a switch or button is programmed for start/stop scan, the menu for
stopping scan are disabled.
See Section 7.4
and switches.
5.30 MONITOR AND SQUELCH TYPES (CONVENTIONAL ONLY)
The monitor function allows you to temporarily turn off selected squelch to monitor for traffic that may
not normally break squelch. The type of squelch used depends on an analog or digital channel. A button
or switch on the radio can be programmed to start or stop Monitor (see Section 7.4 for the various options
that can be programmed to the radio buttons and switches.).
For analog channels, there is:
• Noise squelch - any received signal breaks squelch.
• Continuous Tone Coded Squelch (CTCSS) - squelch is selective based on tone code.
• Continuous Digital Coded Squelch (CDCSS) - squelch is selective based on digital code.
For digital channels, there is:
• Monitor squelch - any received digital signal breaks squelch.
• Normal squelch - Received Network Access Code (NAC) must be correct to break squelch.
• Selective squelch - Received NAC and talkgroup Identification (ID) or unit ID must be correct to
break squelch.
During encrypted operations, the radio only unmutes when receiving with the same key.
60
14221-1800-2000, Rev. F
To perform nuisance delete from the menu:
1. Press the Menu/Select button to access the main menu.
to add channel back to scan list. If you do not add the channel back
scan list when you cycle radio power
11. Press the BACK soft key to exit the scan list display.
NOTE
5.31 NUISANCE DELETE
A channel can temporarily be deleted from the scan list. The selected channel, priority 1, and priority 2
channels cannot be nuisance deleted.
A button or switch on the radio can be programmed for nuisance delete (see Section 7.4 for the various
options that can be programmed to the radio buttons and switches).
Nuisance delete can only be performed on the active scan list.
2. Press or to display the SCAN menu.
3. Press or to highlight SCAN LISTS and press the Menu/Select button.
4. Press or to highlight the scan list and press the Menu/Select button.
When scanning is started, indicates the active scan list; when scanning is
stopped, indicates the active scan list.
5. Press or to highlight the desired channel.
6. Press the OPTIONS soft key.
7. Press or to highlight NUISANCE and press the Menu/Select button.
8. The icon appears next to the channel and it will not be scanned.
9. Highlight the channel, press the OPTIONS soft key, and select ADD
BACK
to the list, the channel will return to the
or activate a personality.
10. Press the BACK soft key to exit the channel lis t.
61
14221-1800-2000, Rev. F
and hold the emergency button on the radio or the speaker
The length of time you need to hold the button is configured
The radio can also be programmed to send an Emergency Alarm in addition to or in place of the
the radio is transmitting or press PTT to talk.
If enabled via programming, you can clear an emergency by pressing the
Monitor/Clear function and then the emergency
button.
NOTE
5.32 CONVENTION AL FAILSOFT (EDACS ONLY)
In the unlikely event of an EDACS system failure, communications can take place in Conventional
Failsoft mode. The radio is automatically directed to a communications channel set up for this purpose.
An increase in activity on the channel during Conventional Failsoft operation may be noticed, so be
careful not to transmit until the channel is clear.
Operation during Conventional Failsoft is the same as operation on a conventional system, except that it
is not possible to select a communications channel, or use emergency and special call. When trunking is
restored, the radio automatically returns to normal operation.
Emergency and special calls are not operational during Conventional Failsoft.
5.33 EMERGENCY OPERATION
The XL-200P ca n be programmed to enable emergency mode. Unit name displays on dispatcher console
if an emergency signal is received from another XL-200P on a digital channel.
5.33.1 Declaring an Emergency Call
To declare an emergency:
1. Press
microphone.
using RPM2.
2. The emergency icon is displayed on the idle display.
• For digital channels, the radio transmits the talkgroup or radio ID to the dispatch console and
receiving radio.
• The radio can be programmed to have a dedicated emergency channel, which can be activated
from analog or digital channels.
•
emergency call (P25 modes).
The radio goes through transmit and receive cycles if so configured. Speak into the microphone while
3. To exit emergency, power cycle the radio or select EXIT EMERGENCY
from the CALL menu.
button programmed for the
5.33.2 Receiving an Emergency Call
When receiving an Emergency Call, an alert beep sounds (if tones are enabled) and an emergency
indication is displayed. The unit ID and/or unit name of the unit in emergency is displayed. While the
emergency display is active, press PTT to respond to the emergency caller.
62
14221-1800-2000, Rev. F
5.33.3 Stealth Emergency
The radio can be programmed with the following emergency behavior:
• No audio indications when declaring an emergency.
Or
• No visual indications when declaring an emergency.
Or
• No audio and no visual indications when declaring an emergency.
During stealth mode, the radio will not receive any type of call. Once the user presses the PTT button, the
radio display and audio return to normal.
5.34 MDC-1200 (ANALOG CONVENTIONAL ONLY)
MDC-1200 is a legacy in-band signaling protocol that provides the radio with the ability to transmit and
receive a unique PTT ID. This PTT ID can be decoded by receiving radios and displayed as a
hexadecimal number or an alias string. In addition, MDC-1200 provides radios with the ability to transmit
emergency status to a console. Refer to the MDC-1200 Feature Manual, 14221-7200-6000, for complete
instructions on configuring and using this feature.
5.34.1 Normal PTT Operation
If MDC signaling on PTT press is enabled using RPM2, the radio transmits an MDC PTT ID message
when PTT is pressed. If the Sidetone option is enabled using RPM2, the radio plays a Ready-to-Talk
(RTT) tone after the MDC pre-signaling has been transmitted.
If MDC signaling on PTT release is enabled (using RPM2), the radio transmits post-call MDC signaling
when PTT is released.
• IF STE is enabled (using RPM2), the MDC post-call signaling is transmitted after STE is sent on PTT
release only.
• MDC post-call signaling is also sent when there is a radio unkey due to Carrier Control Timeout
(CCT). Normal CCT alert tones occur prior to unkey.
5.34.2 MDC PTT ID Receive Handling
When the radio receives an MDC PTT ID, it searches the MDC ID Alias List for an alias associated with
the ID. If one is found, it displays the alias. If none is found, the radio displays the ID in hexadecimal.
5.34.3 Emergency Declaration
Emergency declaration is accomplished by the radio generating an MDC Emergency PTT message. An
Emergency is considered acknowledged when the radio receives an “Ack To Emergency” PTT message
with an ID which matches its own ID. If Emergency Audio is enabled and the PTT Sidetone option is
enabled, the radio plays the Ready-to-Talk tone after the MDC Emergency PTT signaling is transmitted.
• If an MDC Alert on ACK is enabled, the radio plays an ACK tone when the MDC emergency is
acknowledged.
• If audio tones are enabled, the radio plays an ACK tone if the emergency is not acknowledged within
the programmed number of retries.
63
14221-1800-2000, Rev. F
NOTE
5.35 BEON OPERATION
The BeOn solution is a Voice over IP (VoIP) based, Push-to-Talk (PTT) communications system
operating over public or private wireless networks. The solution extends traditional Land Mobile Radio
(LMR) services onto the broadband capable third generation (3G) and 4G/LTE cellular networks. This
includes the ability to provide highly integrated interoperability services between BeOn users on the
cellular network and users of traditional LMR networks. Harris’ VIDA® IP core network switching
technology is the foundation for the BeOn application infrastructure. As a result, the application and
product suite provide many advanced features not found in competing technologies, and provide
internetworking of those services between public and private communications networks.
The XL-200P supports BeOn operation on Wi-Fi or LTE.
It may be necessary to consult one or more of the following when configuring and using BeOn:
• BeOn Configuration and Use Feature Manual: 14221-7200-6130
• BeOn LAS/LAP Installation and Configuration Manual: 14221-710-3010
• Unified Administration System User’s Manual: MM24374
• RPM2 online help
64
14221-1800-2000, Rev. F
To view a personality:
1. At main display, press the Menu/Select button to access the main menu.
6. ADVANCED OPERATIONS
6.1 VIEW/CHANGE PERSONALITIES
Personalities contain radio programming information such as frequencies, channels, stations, and talk
groups. Up to 10 different personalities can be stored in the radio, but only one can be activated at a time.
6.1.1 View Personalities
2. Press or to display the UTILITY menu.
3. Press or to highlight PROGRAM and press the Menu/Select button.
An arrow indicates the currently active personality.
4. Press the OPTIONS soft key.
5. Select VIEW PLAN INFO to view.
6. The radio displays the plan’s filename. Personality information appears if the
field was filled out using RPM2.
65
14221-1800-2000, Rev. F
highlight the desired personality and press the Menu/Select
If the personality
up PIN, you are prompted to enter the PIN before activation
You cannot activate a personality when the radio is transmitting an
in the fill or some other invalid parameter.
6.1.2 Change Active Personality
To change the active personality:
1. At main display, press the Menu/Select button to access the main menu.
2. Press or to display the UTILITY menu.
3. Press or to highlight PROGRAM and press the Menu/Select button.
4. Press or to
button. indicates the currently active personality .
5. Press the YES soft key to confirm personality activation.
has a powercontinues.
6. The IN PROGRESS screen is displayed while plan activation is in progress.
7. If personality i s activated, the radio displays PLAN COMPLETE followed
by the name of the personality. Press the OK soft key.
•
emergency.
• A FAILED message may be displayed for errors such as invalid syntax
66
14221-1800-2000, Rev. F
To display Situational Awareness Info:
1. Press the Menu/Select button to access the main menu.
and press the Menu/Select
The color of each unit
indicates its status as follows. Only one status can be shown at a time and
8. Press or to zoom the display distance of current unit.
to display
select EXIT.
6.2 SITUATIONAL AWARENESS (SA) – P25 CONVENTIONAL ONLY
Situational Awareness is a feature in which the XL-200P receives SA position from other units
configured to send the SA packets. The SA display shows the positions of the other radios (units) relative
to the XL-200P. To make use of SA, all radios need to have a uniquely programmed Unit ID.
2. Press or to display the UTILITY menu.
3. Press or to select GPS and press the Menu/Select button.
4. Press or to select POSITION INFO
button.
5. Press the NEXT soft key.
6. Press or to view the location of each unit.
are listed in prior ity order:
• Grey – Unselected, no statu s
• Red – Unselected, In Emergency
• Orange – Unselected, Low Battery
• Blue - Unselected, Scanning
• Green – Selected, no status
• Green/Red – Selected, In Emergency
• Green/Orange – Selected, Low Battery
• Green/Blue - Selected, Scanning
7. GPS of this radio is shown by the center dot as follows:
• Green – Tracking
• Orange – Last known position
• Red – Searching
9. Press the OPTIONS soft key. From here, select UNITINFO
details about the selected unit, select REFRESH to update information, or
67
14221-1800-2000, Rev. F
To create a Command Tactical Zone:
1. Press the Menu/Select button to access the main menu.
2. Press or to display the ZONE menu.
(up to 16 characters are
8. After adding all desired channels/groups, press the BACK soft key.
NOTE
6.3 USER-DEFINED ZONES/SYSTEMS
6.3.1 Command Tactical Zone
A Command Tactical Zone is defined at the radio.
A Command Tactical Zone is reset when a Personality is activated.
3. Press or to highlight <USER-DEFINED> and press the VIEW
ZONE soft key.
4. Press the OPTIONS soft key.
5. Press or to select EDIT ZONE to create a zone, or RENAME
ZONE to rename the Command Tactical Zone
allowed).
6. Press or to scroll through existing systems. Press or to
highlight desired channel/group.
7. Press the Menu/Select button to add or remove channel/group.
9. Activate the Command Tactical Zone by selecting the SET ACTIVE soft
key on the USER DEFINED screen, or by pressing the Menu/Select
button when <USER DEFINED> is highlighted on the Zone menu.
10. After a creating a Command Tactical Zone, select OPTIONS to edit the
Command Tactical Zone, delete channels/groups, clear the zone, and
rename the zone.
68
14221-1800-2000, Rev. F
To view Mixed System Zones:
1. Press the Menu/Select button to access the main menu.
to view the groups/channels in the
To display channel information:
1.
2.
CONVENTIONAL
3.
4.
values of the displayed channel parameters.
The password remains active until power cycle. Refer to Section 7.2 for more information.
6.3.2 Mixed System Zone
Mixed System Zones are defined using RPM2 and cannot be edited on the radio. If a Mixed System Zone
is not configured using RPM2, it will not appear on the radio. Up to 50 Mixed System Zones can be
defined. You can view details about each channel/group. A user programmable button can be defined to
scroll through just the mixed system zones.
2. Press or to display the ZONE menu.
3. Press or to highlight the desired zone (Note: Zones are indicated by
the icon) and select VIEW ZONE
zone list.
6.4 CH INFO MENU
The Channel Information (CH INFO) menu displays information about the currently selected channel.
The information displayed varies between conventional and trunked systems.
Press while on the idle display.
Press or to scroll through the programmed channel settings.
OR P25 CHANNELS ONLY:
Press the EDIT soft key.
Enter the password. You may now select and change the
69
14221-1800-2000, Rev. F
To set audio settings:
1. Press the Menu/Select button to access the main menu.
2.
3.
the Menu/Select
4.
to scroll through available audio settings. Press the
.
to prevent
holster or you are
Enable or disable keypad tones. When enabled, the
5. Press the BACK soft key to exit menu.
6.5 AUDIO SETTINGS
Set audio settings such as speaker mute, noise cancellation, PTT, and tones.
Press or to display the UTILITY menu. Press or highlight AUDIO SETTINGS and press
button.
Press or
Select/Menu button to change settings as desired:
• SPEAKER - Mute or Unmute the speaker audio.
• NOISE CANCELLATION - Enable or disable noise cancellation
Noise cancellation reduces background noise during transmit.
•PTT - Enable or disable Push-To-Talk (PTT). Disable PTT
accidental keying, such as when the radio is in a
getting into a car.
• TONES - Enable or disable alert tones (see Table 5-6).
• KEYP AD TONES -
radio plays a tone when a button on the keypad is pressed.
70
14221-1800-2000, Rev. F
To change display settings:
1. Press the Menu/Select button to access the main menu.
2.
3.
to highlight DISPLAY SETTINGS and press the
4.
Change the color scheme of the top and front
Turn front display backlight on, off,
Momentary (off) is similar to
momentary, but the backlight turns off completely and only comes
brightness level of front display. A
Specify how long the radio needs to be
klight
Set the brightness level of the top display. A
Specify how long the radio needs to be inactive
Set orientation of top display to be viewed
200P changes top display to be viewed
e,
• INDICATOR LED - Toggle the indicator LED ON/OFF.
5. Press the BACK soft key to exit the menu.
6.6 DISPLAY SETTINGS
Press or to display the UTILITY Menu. Press or
Menu/Select button.
Press or and the Select/Menu button to change settings as desired:
• COLOR SCHEME -
displays for optimum viewing in day/night conditions.
• FRONT BACKLIGHT -
momentary, or momentary (off).
on when the center navigation button is pressed.
• FRONT BRIGHTNESS - Set
level of 0 has same effect as turning off backlight.
• FRONT TIMEOUT -
inactive before the front display’s backlight turns off.
• TOP BACK LIGHT - Specify how long the top display’s bac
will remain lit: MOMENTARY, ON, or OFF.
• TOP BRIGHTNE SS -
level of 0 turns off top display and indicator (TX/RX) LED.
• TOP T IMEOUT -
before the top display’s backlight turns off.
• TOP ORIENT ATION -
When AUTO is selected, the XLfrom back if an external microphone or speaker is attached. Otherwis
the display can be viewed from the front.
from radio: FRONT, BACK, or AUTO.
71
14221-1800-2000, Rev. F
To access GPS settings:
1. Press the Menu/Select button to access the main menu.
2.
3.
and press the Menu/Select
4.
splayed linear units:
Set unit of measurement of displayed angular
Set format of displayed position information:
),
or
Universal Transverse Mercator (UTM).
To display position info:
1. Press the Menu/Select button to access the main menu.
2.
3.
and press the Menu/Select
4.
NOTE
6.7 GPS SETTINGS
The GP S SETTINGS menu it em only appears if enabled usi ng RPM 2 and the feature
is installed.
Press or to display the UTILITY menu. Press or to highlight GPS SETTINGS
button.
Use or and the Select/Menu button to change settings as desired:
• GPS - Enable or disable internal GPS.
• POSITION INFO - See Section 6.8.
• LINEAR UNITS - Set unit of measurement of di
STATUTE, METRIC, or NAUTICAL.
•ANGULAR UNITS -
units: CARDINAL, DEGREES, or MILS.
•POSITION FORMAT-
Latitude/Longitude Degrees Minutes Seconds (LAT/LONG DMSLAT/LONG DM, Military Grid Reference System (MGRS),
4. Press the BACK soft key to exit the menu.
6.8 POSITION INFO
The Position Info screen displays the radio user’s location information. GPS must be enabled in the GPS
Settings (see Section 6.7).
Press or to display the UTILITY menu. Press or to highlight POSITION INFO
button.
Press or to scroll through available location information.
72
6.9 WI-FI
The XL-200P supports programming via Wi-Fi. Refer to Appendix A for information on configuring WiFi.
To enable Wi-Fi programming mode on the radio:
1. Ensure the radio is powered off.
2. Press and hold the bottom side button and PTT button (see Figure 4-1).
14221-1800-2000, Rev. F
Figure 6-1: Enabling Wi-Fi
3. Power on the radio.
4. The WIFI INSTALL ACTIVE screen is displayed (Figure 6-2). The radio displays
DISCONNECTED if not connected to a wireless network, or CONNECTED if connected to a
wireless network.
Figure 6-2: Wi-Fi Install Active
73
14221-1800-2000, Rev. F
To enable Bluetooth:
1. Press the Menu/Select button to access the main menu.
and press the Menu/Select
NOTE
6.10 BLUETOOTH
The BLUETOOTH menu item only appears if enabled using RPM2 and if the feature is
installed.
6.10.1 Enable Bluetooth
2. Press or to display the UTILITY menu.
3. Press or to highlight BLUETOOTH
button.
4. Press or to hi ghlight ENABLED and press the Menu/Select button to
toggle YES/NO.
74
14221-1800-2000, Rev. F
To pair devices:
1. Press the Menu/Select button to access the main menu.
and press the Menu/Select
and press the Menu/Select
Make sure device being paired is powered on and has discovery mode
9. Press or highlight the desired device and press the PAIR softkey.
10. Pairing progress is displayed.
Enter the pin code and select OK.
6.10.2 Pair Devices
2. Press or to display the UTILITY menu.
3. Press or to highlight BLUETOOTH
button.
4. Press or to hi ghlight PAIRING MGMT
button.
5.
enabled in order to pair with the XL-200P.
If no devices are found and Bluetooth is enabled, only the ADD NEW soft
key is available. If devices are paired, the OPTIONS soft key appears.
6. Press the ADD NEW soft key to select a device to pair.
7. A list of available Bluetooth devices appears.
8. Press the REFRESH soft key to refresh the device list if the desired device
does not appear.
• For Bluetooth 2.0 devices, a pin code screen appears.
• For Bluetooth 2.1 devices, a PASSKEY accept/deny screen appears.
Select ACCEPT.
Accept the passkey on the Bluetooth 2.1 device as well.
11. A PAIRING COMPLETE message appears when pairing is complete.
Select OK. The paired dev ice is then dis play ed in the PAIREDDEVICES
list.
75
14221-1800-2000, Rev. F
To view/change clock settings:
1. Press the Menu/Select button to access the main menu.
5. Press the BACK soft key to exit.
To display battery information:
1. Press the Menu/Select button to access the main menu.
2. Press or to display the UTILITY menu.
and press the Menu/Select
button.
and press the Menu/Select
approved batteries. Injury could occur from using incorrect
WARNING
6.11 CLOCK SETTINGS
2. Press or to display the UTILITY menu.
3. Press or to highlight CLOCK SETTINGS and press the Menu/Select
button.
4. Use or and Menu/Select button to change settings as desired:
• TIME FORMAT- Set 12 or 24 hour time display format.
• TIME ZONE - Set time zone relative to Universal Time Coordinated
(UTC).
6.12 BATTERY INFO
3. Press or to highlight MAINTENANCE
4. Press or to highlight BATTERY INFO
button.
5. Battery information is displayed (state, voltage, capacity, and chemistry).
Use only Harris
battery.
76
14221-1800-2000, Rev. F
To change the language displayed by the XL-200P:
1. Press the Menu/Select button to access the main menu.
and press the
the desired language and press the Menu/Select
To access the scan lists:
1. Press the Menu/Select button to access the main menu.
and press the Menu/Select button.
NOTE
6.13 SELECT LANGUAGE
2. Press or to display the UTILITY menu.
3. Press or to highlight CHANGE LANGUAGE
Menu/Select button.
4. Press or to highlight
button.
6.14 SET UP SCAN
These procedures are used to set up the scan list, home channels, and priority channels.
2. Press or to display the SCAN menu.
3. Press or to highlight SCAN LISTS
Refer to the following sections.
When using Preemptive Priority Scan, the frequencies in the list need to be unique.
6.14.1 Default, Priority 1, and Priority 2 Channels
6.14.1.1 Default Channel
This is the currently selected channel and is the channel you transmit on by default when you press PTT
while the radio is actively scanning and is not responding to a just received call. Responding to a call the
radio just received while scanning is called hang time. If hang time is set to 0 using RPM2, t he radio
always transmits on the default channel in scan.
6.14.1.2 Priori ty 1 Channel
This channel will be scanned more often than other channels in the list and will be scanned in between
every other channel in the scan list. An example scan sequence would be P1 (priority 1), C2, P1, C3, P1,
C4, etc. In addition, the priority channel will be scanned even while actively receiving on a non-priority
channel. For example, if the radio is actively receiving on C3 and activity is detected on P1, the radio will
drop C3 and switch to P1.
77
14221-1800-2000, Rev. F
NOTE
NOTE
6.14.1.3 Priori ty 2 Channel
This channel will also be scanned more often than others. An example scan sequence would be P1, C2,
P1, C3, P1, C4, P2, C5, P1, C6, P1, C7, P1, C8, P2, C9 etc. In addition, this channel will be scanned even
while actively receiving on a non-priority channel. For example, if the radio is actively receiving on C 3
and activity is detected on P2, the radio will drop C3 and switch to P2. Additionally, activity on P1 can
also preempt P2, but P2 cannot preempt P1.
6.14.2 Trunked/Conventional Scanning
Trunked/conventional scanning adds the ability to scan multiple conventional and P25 conventional
channels while still maintaining trunked radio operation. In essence, the radio is able to scan a
conventional scan list while still receiving a trunked control channel and receiving trunked
calls. Selection of which conventional scan list is associated with a given trunked system is done using
RPM2 and cannot be changed on the radio. However, a user with access to the necessary menu layout
(see Section 5.8) is allowed to edit the scan list members (both trunked groups and conventional channels
on the selected Conventional Priority System). As the number of conventional channels being scanned
increases, the time between scanning each channel increases (roughly 250 milliseconds per channel), with
the consequent increase in the number of calls that will late-enter. In order to avoid missing calls, it is
recommended to keep the number of conventional channels being scanned to eight (8) or fewer.
The trunking site must have roaming set to Enhanced CC.
6.14.3 Vote Scan (Analog and P25 Conventional Only)
If vote scan is enabled via RPM2, the radio automatically selects the strongest signal ensuring that the
best audio quality is delivered to the user. If vote scan is enabled, the radio is always scanning. You
cannot stop scanning, start normal scanning, or monitor the channel. The scanning icon on the idle screen
indicates that the radio is vote scanning versus, regular scanning.
If Talkaround is enabled, Vote Scan is disabled unt il Talkaround is disabled again.
78
14221-1800-2000, Rev. F
To edit the scan list:
1. Press the Menu/Select button.
CHAN
8. Press the Menu/Select button to toggle selection.
6.14.4 Edit Scan List
Depending on the scan list options selected via RPM2, you may be able to add or remove channels/groups
from the scan list.
2. Press or to display the SCAN menu.
3. Press or to select SCAN LISTS.
4. Press or to highlight the scan list and press the Menu/Select button.
5. Press or to highlight channel/group.
6. Select OPTIONS.
7. Press or to select ADD CHAN/DELETE CHAN, SET PRI1, SET
PRI2, REMOVE PRI, or NUISANCE/ADD BACK.
When a channel is not grayed out in the list, DELETE
appears. When a channel/group is grayed out (not in list), ADD CHAN
appears.
79
14221-1800-2000, Rev. F
To set or remove priority 1 and priority 2 channels:
1. Press the Menu/Select button.
to highlight SET PRI1 or SET PRI2 and press the
Menu/Select button. A Priority 1 channel appears with a P1 and a Priority 2
6.14.5 Set or Remove Priority 1 and Priority 2 Channels
Priority channels are scanned more often than non-priority channels. Note that P1 and P2 can only be set
if configured as “Keypad” and the scan list is not set to “Fixed” using RPM2.
2. Press or to display the SCAN menu.
3. Press or to highlight SCAN LISTS and press the Menu/Select button.
4. Press or to highlight channel/group.
5. Select OPTIONS.
6. Press or
channel appears with a P2.
7. Select REMOVE PRI to remove priority.
6.14.6 Custom Scan Lists
The Mixed Zone Scan (MZS) feature gives the user the capability to scan based on a custom scan list that
is assigned at the system level. The Custom Scan (CS) list can contain System and Channel/Group
configurations across P25 Trunked, P25 Conventional, and Analog Systems. When a Custom Scan List is
assigned to a P25T system, the radio can scan P25T, P25C and Analog systems. When assigned to a
P25C or Analog system, the radio only scans conventional channels. MZS also gives the user the
capability to scan beyond the selected system group set.
• P25T Scan
When a custom scan list is assigned to a P25T system, the user has the ability to scan P25T, P25C,
and Analog groups/channels. All P25T systems must have the same WACN, System ID, and Unit ID
to be added to the custom scan list. If P25C and/or analog channels are added to the custom scan list,
the radio will scan them using the Trunked/Conventional scan feature described in section 6.14.2, and
will override any other conventional scan list that may have been programmed using RPM2.
• P25C and Analog Scan
When a custom scan lists is assigned to a P25C or Analog System, the user has the ability to scan
P25C and Analog channels. P25T systems are ignored.
Custom scan list can be created using RPM or at the radio. The radio supports up to 10 Custom Scan lists,
with up to 100 channels/groups in each.
80
14221-1800-2000, Rev. F
To create a custom scan list at the radio:
1. Press the Menu/Select button.
and press the
the newly added scan list and press the
the desired group/channel and press the
From here, you can add/delete channels from the scan
NOTE
6.14.6.1 Create Custom Scan List
2. Press or to display the SCAN menu.
3. Press or to highlight ASSIGNED CUSTOM LIST
Menu/Select button.
4. Press the OPTIONS softkey.
5. Select ADD SCAN LIST.
6. Press or to highlight
VIEW/EDIT soft key.
7. Press or to display the desired system.
8. Press or to highlight
OPTIONS softkey.
list, and set/remove Priority 1 and Priority 2 channels.
When a custom scan list is selected, that list is scanned any time scanning is enabled
for any Trunked, conventional, or P25 Conventional system. To scan only the channels
assigned to a particular system, custom scanning must be turned off.
81
14221-1800-2000, Rev. F
and press the Menu/Select
4. Select BACK to exit the scan menu.
and press the Menu/Select
NOTE
6.14.7 Wide Area System Scan (P25 Trunked and EDACS)
Wide Area System Scan (WASCAN) causes the radio to roam across mobile systems when the currently
selected system's control channel is lost. The radio will scan the control channels of other systems.
To enable/disable Wide Area System Scan:
1. Press the Menu/Select button to access the main menu.
2. Press or to display the SCAN menu.
3. Press or to highlight SITE ROAMING
button to toggle Wide Area System Scan ENABLED/DISABLED.
6.15 RADIO STATUS
The status feature is used to send a particular status condition to the site without making a voice call.
There can be up to 10 status conditions programmed into the radio. For each status defined, there is an ID
and an alphanumeric name. The ID is sent to the site and the alphanumeric name appears on the radio
display when the ID corresponds with the information programmed at the site.
A button on the radio can be programmed to send a radio status (see Section 7.4).
To send a radio status:
1. Press the Menu/Select button to access the main menu.
2. Press or to display the MESSAGES menu.
3. Press or to highlight RADIO STATUS
button.
4. Use or and the Menu/Select button to highlight and select desired
status.
82
14221-1800-2000, Rev. F
NOTE
6.16 RADIO MESSAGE
The message feature is used to send a particular message to the site without making a voice call. There
can be up to 10 messages programmed into the radio. For each message defined, there is an ID and an
alphanumeric name. The ID is sent to the site and the alphanumeric name appears on the radio display
when the ID corresponds with the information programmed at the site.
A button on the radio can be programmed to send a radio message (see Section 7.4).
To send a radio message:
1. Press the Menu/Select button to access the main menu.
2. Press or to display the MESSAGES menu.
3. Press or to highligh t RADIO MESSAGE and press the Menu/Select
button.
4. Use or and the Menu/Select button to highlight and select the desired
message.
6.17 RADIO TEXTLINK
Radio TextLink provides short text messaging functionality for radios. Due to the difficulty of entering
text messages on a radio, predefined "canned" messages and predefined replies can be stored in the radio.
To facilitate sending messages where information must be provided at send time, text message forms can
also be stored in the radio. A form can contain up to four (4) text prompts, for which the operator enters
alphanumeric values before sending the message.
83
14221-1800-2000, Rev. F
and press the
• Select TOD QUERY to get the time of day.
the desired message and press the Menu/Select
Enter text into blank field(s) (up to eight alphanumeric characters) and press
to change the
6.17.1 Radio TextLink Messages
To send a canned Radio TextLink messag e:
1. Press the Menu/Select button to access the main menu.
2. Press or to display the MESSAGES menu.
3. Press or to highlight TEXTLINK MESSAGES
Menu/Select button.
4. Press or to display the desired message.
• Press the Menu/Select button to send the message.
• SelectCHG CALLEE to change the destination for the message.
6.17.2 Radio TextLink Forms
Form messages are displayed and stored in the radio as a message in which each field to be filled is
indicated by a question mark (?) followed by one or more asterisks(*). The number of asterisks indicates
the maximum number of alphanumeric characters allowed for that field.
To send a Radio TextLink form:
1. Press the Menu/Select button to access the main menu.
2. Press or to display the MESSAGES menu.
3. Press or to highlight TEXTLINK FORMS and press the Menu/Select
button.
4. Press or to display
button.
5.
the NEXT soft key.
6. Select SEND to send the message. Select CHG CALLEE
destination for the message. Select TOD QUERY to get the time of day.
84
14221-1800-2000, Rev. F
and press the
To view and clear faults/alerts:
1. Press the Menu/Select button to access the main menu.
and press the Menu/Select
Check antenna and antenna connection. Try
this radio.
NOTE
6.17.3 View Received Messages
When the icon appears on the idle d isp lay , there are Radio TextLink messages waiting to be read.
To view received Radio TextLink messages:
1. Press the Menu/Select button to access the main menu.
2. Press or to display the MESSAGES menu.
3. Press or to highlight TEXTLINK MAILBOX
Menu/Select button. From the mailbox, select OPTIONS to delete messages,
view details of messages, and reply to messages.
6.18 FAULTS/ALERTS
is displayed on the idle display when there is a fault.
2. Press or to display the MESSAGES menu.
3. Press or to highlight FAULTS/ALERTS
button.
4. Fault messages are displayed. Press or to highlight the des ired f ault.
Press the OPTIONS soft key delete faults. Press the DETAILS so ft ke y to
view details for the highlighted fault.
Possible faults include:
• BATTERY FAULT- Replace battery.
• EEPROM FAULT - Contact Harris.
• RF FAULT - Contact Harris.
• OVERCURRENT -
replacing antenna.
• INVALID SYSTEM - Feature not in stalled.
• CHANNEL F AULT - Channel frequency programmed is not valid for
5. If you view but do not delete the fault, the alert icon goes away on the idle display.
Contact Harris for assistance with diagnosing a fault.
85
14221-1800-2000, Rev. F
and press the Menu/Select
6.19 TONE ENCODE
Tone Encode is a generic tone encoding scheme for call identification when transmitting on a
conventional system. It supports generic user-definable tone encode (up to 15 tones), Type 99 (up to 2
tones) and 5/1 Tone (up to 5 tones) encoding formats.
Tone encoding schemes are used to transmit calls to one or more target radios that have been programmed
with the correct tone decode sequence. When the receiving radio detects its tone decode sequence, it
unmutes on the call.
To select a Tone Encode option:
1. Press the Menu/Select button to access the main menu.
2. Press or to display the CALL menu.
3. Press or to highlight TONE ENCODE
button.
4. Select the desired Tone Encode option from the list.
6.20 ENCRYPTION
6.20.1 Create and Load Keys
Refer to the following documentation for advanced programming and setup instructions:
• Harris OTAR Overview Manual - MM-008069-001
• Network Key Manager Installation and Configuration Manual - MM-008070-001
KVL 3000 Plus Key Variable Loader (KVL) User's Guide
86
14221-1800-2000, Rev. F
To zeroize keys from the radio:
1. Press the Menu/Select button to access the main menu.
and press the Menu/Select
This will also remove the
6.20.2 Zeroize Keys from Radio
It may be necessary to remove keys because of compromise or expiration.
2. Press or to display the SECURITY menu.
3. Press or highlight ZEROIZE KEYS
button.
4. Press the YES softkey to remove the keys.
keysets.
6.20.3 Protected Keys
The Protected Keys feature transfers P25 Voice Keys, from Harris Key Loader to the radio, that have
been wrapped (AES) or encrypted (DES) with Key Protection Keys (KPKs). KPKs are nothing more than
unprotected Key Encryption Keys (KEKs). The KPKs need to be loaded into the radio before the
Protected Keys are loaded. Once loaded into the radio, the KPKs are used to unw rap (AES) or d ecrypt
(DES) the Protected Keys.
6.20.4 Global Encryption
Global Encryption can be enabled when encryption keys are loaded on the radio and the selected
Zone/System is encrypted. When Gl obal E ncryp tion is enabled on the radio, a Global Key is used for all
encrypted transmissions until:
• Global Encryption is disabled.
• A new personality is activated.
• The active keyset is changed.
• The system is changed.
87
14221-1800-2000, Rev. F
To enable Global Encryption and/or change Global Encryption Key::
1. Press the Menu/Select button to access the main menu.
2. Press or to display the SECURITY menu.
8. The optional global key icon is displayed on the main display.
To select a keyset:
1. Press the Menu/Select button to access the main menu.
2. Press or to display the SECURITY menu.
Global Encryption behavior is available on all channels that support encrypted communications.
3. Press or to highlight GLOBAL ENCRYPTION. Press the
Menu/Select button.
4. Press or to highlight the desired Global Key and press the Menu/Select
button to enable Global Encryption.
5. To change the selected global key, press or to highlight GLOBAL
KEY on the SECURITY menu. Press the Menu/Sele ct key .
6. Press or to highlight the global key and press the Menu/Select button.
7. RPM2 allows Key Numbers to be given Key Names.
6.20.5 Select Keyset
3. Press or to select ACTIVE KEYSET. Press the Menu/Select button to
toggle to the inactive keyset.
88
14221-1800-2000, Rev. F
To view the key list:
1. Press the Menu/Select button to access the main menu.
2. Press or to display the SECURITY menu.
To enable OTAR and request rekey:
1. Press the Menu/Select button to access the main menu.
press the Menu/Select button to
6.20.6 View Key List
3. Press or to select KEY LIST and press the Menu/Select button.
4. The available key lists are displayed.
6.20.7 OTAR Configuration
OTAR is t he over-the-air-rekeying from a KMF and must be enabled for the digital only channel using
RPM2. For OTAR operation, the appropriate KEKs must be loaded into the radio using the Harris Key
Loader or a KVL device.
The KMF Configuration must include the RSI of the KMF and the appropriate Message Number Period.
2. Press or to display the SECURITY menu.
3. Press or to highlight OTAR and
toggle ENABLED/DISABLED.
4. Press or to select OTAR REKEY and press the Menu/Select button to
request that the KMF updates the keys in the radio.
Note: OTAR REKEY is only enabled if the radio has successfully registered
for data operations.
89
14221-1800-2000, Rev. F
To edit a channel:
CAUTION: Only authorized users should attempt channel editing.
CAUTION
NOTE
7. PROGRAMMING
This section provides information on front panel programming. Programming can also be accomplished
by creating a plan using a computer with RPM2 installed.
7.1 PROGRAMMING VIA RPM2
Radio Personality Manager (RPM2) is used for the bulk of progra mmin g th e XL-200P. With RPM2, you
can fully program the XL-200P using cable 12082-0410-A1.
Removing power during radio programming, or programming the radio with low battery
power could corrupt installation of firmware.
Ensure that the radio is turned off before connecting the programming cable. After the
cable is connected, then power on the radio.
7.2 EDIT CHANNEL (ANALOG AND P25 CONVENTIONAL ONLY)
Channels can be edited from the Channel Information (CH INFO) menu display. Most of the displayed
channel parameters can be modified here. Channel edits persist across a power cycle. Loading a
personality clears any channel edits. Available parameters vary depending on whether the channel is a
P25 or analog channel.
1. From the main display, press to access the CH INFO screen.
2. Press or to scroll through the programmed channel settings.
3. Press the EDIT soft key.
4. Enter the password programmed via RPM2. You do not have to re-enter the
password until you power cycle the radio.
5. Press the ENTER soft key.
6. Highlight and select the parameter to edit. For P25 channels, modify remaining channel settings:
• CHANNEL NAME - Up to 16 alphanumeric characters are allowed.
• RX FREQ UENCY - Receive frequency. Note that if the new frequency is invalid, the display
reverts to the old frequency (Table 7-1).
• TX FREQUENCY - Transmit frequency.
• TX POWER - Transmit power. Toggle between LOW and HIGH.
90
14221-1800-2000, Rev. F
is not available on this screen if it was enabled from the
is not available on this screen if it was enabled from the
GUARD edit is Disabled, the asterisk goes away and the channel is no longer
NOTE
NOTE
NOTE
• TALKGROUP – Select a talkgroup for the channel. Talkgroup name cannot be set here.
• RX NAC - Network Access Code (NAC) radio uses for Normal squelch in receive.
• TX NAC - NAC radio transmits to break Normal squelch on receiving radio.
• P25 SQUELCH - Select type the radio uses in receive. Select NORMAL, SELECTIVE, or
MONITOR.
•RX CHAN GUARD – Squelch type radio uses in receive. Select Noise, CTCSS, or CDCSS. For
a digital channel, the RX CHAN GUARD is used to receive from a Conventional analog channel
that is on the same frequency and uses the selected Channel Guard.
RX CODE - Code radio looks to unmute the speaker on the receiving radio when CDCSS
squelch is used in conventional mode.
RX TONE - Tone radio looks to unmute the speaker on the receiving radio when CTCSS
squelch is used in conventional mode.
7. For analog channel, modify remaining channel settings:
• CHANNEL NAME - Up to 16 alphanumeric characters are allowed.
• TX FREQUENCY - Transmit frequency.
• TX POWER - Transmit power. Toggle between HIGH and LOW.
• RX CHAN GUARD - Squelch type radio uses in receive. Select Noise, CTCSS, or CDCSS.
RX TONE - Tone radio uses to break selective squelch on receiving radio. This is available
when RX squelch is set to CTCSS.
RX CODE - Code radio uses to break selective squelch on receiving radio. This is available
when RX squelch is set to CDCSS.
RX CHAN GUARD
CALL menu as per Section 5.22.
•TX CHAN GUARD - Squelch type radio uses in transmit. Select None, CTCSS, or CDCSS.
TX TONE - Tone sent by transmitting radio to allow receiving radio to unmute when CTCSS
squelch is used in conventional mode.
TX CODE - Code sent by transmitting radio to allow receiving radio to unmute when CDCSS
squelch is used in conventional mode.
TX CHAN GUARD
CALL menu as per Section 5.22.
8. An asterisk is displayed in front of the CHANNEL label on the main display when a channel has been
edited. The asterisk is NOT shown for TX Power or Talkgroup changes.
When the only item edited is the TX or RX CHAN GUARD values, and then CHAN
considered edited. This is the only editable item for which this is true.
The XL-200P supports Over-the-Air-Programming (OTAP) via ProFile Manager. RPM2 creates,
modifies and stores personality information while ProFile Manager delivers the personality over the
network to the desired radios. ProFile Manager also contains the ability to read personality information
over-the-air and save the files, so that RPM2 can modify the information if necessary.
You can interrupt the programming process, if necessary, by depressing the Push-to-Talk (PTT) but to n or
declaring an emergency. Once a radio personality update is successfully completed, the radio
automatically resets itself, switches to the new personality, and returns to normal operation. For more
information on using ProFile Manager, refer to software release notes AE/LZT 123 3263/1.
7.4 PROGRAMMABLE BUTTONS AND SWITCHES
7.4.1 Programmable Buttons
Press while on the main display to view the functions assigned to the programmable buttons. The
programmable buttons are programmed using RPM2. A delay of 0 to 10 seconds can be defined using
RPM2 for the programmable buttons. Table 7-2 lists and describes the functions that can be programmed
to the buttons:
Table 7-2: Programmable Button Options
FUNCTION DESCRIPTION
No Operation
Monitor Toggle Toggles Monitor On/Off.
Monitor/Clear Temporarily turn off selected squelch to monitor for traffic that may not normally break
squelch. Also, press this button followed by the emergency button to clear an emergency.
Audio Playback Accesses the AUDIO PLAYBACK menu. See Section 5.27.
Lock Keypad Locks the DTMF keypad, programmable function keys and navigation keys.
Nuisance Delete Performs a Nuisance Delete. See Section 5.31 for more information.
System Up Scrolls up through the list of available systems, stopping at the top of the list.
System Down Scrolls down through the list of available systems, stopping when the end of the list is
reached.
System Up Wrap Scrolls up through the list of available systems, wrapping to the end when the beginning of
the list is reached.
System Down Wrap Scrolls down through the list of available systems, wrapping to the top when the bottom of
the list is reached.
92
14221-1800-2000, Rev. F
FUNCTION
DESCRIPTION
Zone Up Scrolls up through the list of available mixed system zones, stopping at the top of the list. If
no mixed system zones are defined, or there is only one, the user will hear a deny tone
when the button is pressed.
Zone Down Scrolls down through the list of available mixed system zones, stopping when the end of the
list is reached. If no mixed system zones are defined, or there is only one, the user will hear
a deny tone when the button is pressed.
Zone Up Wrap Scrolls up through the list of available mixed system zones, wrapping to the end when the
beginning of the list is reached. If no mixed system zones are defined, or there is only one,
the user will hear a deny tone when the button is pressed.
Zone Down Wrap Scrolls down through the list of available mixed system zones, wrapping to the top when the
bottom of the list is reached. If no mixed system zones are defined, or there is only one, the
user will hear a deny tone when the button is pressed.
Channel/Group Bank
Select
Drop Call Drop or terminate any group call that the radio receives.
Send Status Sends a preconfigured status. S ee Sectio n 6.15 for more information.
Send Message Sends a preconfigured message. See Section 6.16 for more information.
TX Power High/Low Toggle TX Power between LOW and HIGH.
Scan Enable Enable/disable scan.
Secure Enable Toggle Toggles Encryption Mode On/Off. See Sections 5.20 and 6.20 for information on
Home Goes to home channel.
Adjust Squelch Allows the user to adjust the analog squelch level.
Front Backlight Toggles front display’s backlight On/Off/Momentary.
Top Orient Toggles Top Display Front/Back.
Top Backlight Toggles the top display’s backlight On/Off/Momentary.
Flashlight Mode Press and hold to turn on the front and top display backlights. Release the button to turn off
Override
Individual Call Initiate an Individual Call.
OTAR Rekey Initiate an OTAR rekey. See Section 6.20.7.
GPS SA Info Display GPS Situational Awareness (SA) screen.
Site Roaming Enable/disable Site roaming. Site Roaming allows the radio to roam to another site.
Profile Toggle Toggles between the currently active profile (if one has been selected) and no profile.
Numeric Channel
Entry
Select the channel/group bank. If your system has more than 64 channels, this allows you to
select a channel group with ch annel s 65 to 127, 128 to 191, etc.
Encryption.
both displays.
Allow user to pick a different Channel Guard setting for the current channel.
Allows number channel entry.
93
14221-1800-2000, Rev. F
FUNCTION
DESCRIPTION
7.4.2 Programmable A/B (Ø/O) Switch
The programmable A/B switch can be programmed for multiple functions, including:
Sections 7.4.3.1 and 7.4.3.2 describe the various functions that can be programmed to the A/B/C/D
switch.
7.4.3.1 Single-Instance Features
Single-instance features can only be assigned to one switch position at a time. If one of these features is
programmed to the A/B/C/D switch, other means of accessing that feature are disabled (i.e., two-position
switch, programmable buttons, call menu, etc.).
Table 7-4: Single-Instance Features
FUNCTION DESCRIPTION
No Function No function programmed to switch.
Talkaround See Section 5.23.
Scan Enables scanning.
Sets transmission power level to High.
•Changing to a Tx Power High position overrides the current personality or user setting
TX Power High
TX Power Low
Keypad Lock Locks DTMF, programmable, and navigation soft keys.
Radio Lock
for TX Power.
•Changing from a Tx Power High position restores the personality-configured Tx Power
Level.
Sets transmission power level to Low.
•Changing to a Tx Power Low position overrides the current personality or user setting
for TX Power.
•Changing from a Tx Power Low position restores the personality-configured Tx Power
Level.
When set, prevents the radio software from responding to the following physical inputs on
the radio:
• Volume Knob Change (power off is not prevented)
• 2-Position Switch
• Channel Knob
• Side User-Programmable Buttons and Keypad (DTMF, programmable, and
navigation/soft keys)
NOTE: Exception is the emergency button and if any key is programmed for Monitor/Clear, it
can be used with the emergency button to clear emergency, if so programmed.
94
14221-1800-2000, Rev. F
FUNCTION
DESCRIPTION
Selects channels 1-16 in position A; 17-32 in position B; 33-48 in position C; and 49-64 in
Channel Bank
position D.
If Channel Bank is selected for any single position, all 4 positions (A, B, C, and D) will be set
to Channel Bank.
7.4.3.2 Indexed Features
These features can be assigned to any number of positions as long as each index value selected for it is
unique across multiple assignments of the same feature; for example, you cannot assign a Zone with a
particular index (e.g., “ZONE A”) to both positions A and B.
Table 7-5: Indexed Features
FUNCTION DESCRIPTION
Sets to the Zone index value.
•When setting the A/B/C/D switch to an indexed zone assigned position, the radio sets,
but does not “hold,” that zone. This has the resulting effects:
This sets the channel knob to be zone-based system/channel selection just like
selecting a zone from the main “Zone” menu or ramping up/down using the side
Zone Selection
•When changing away from a Zone assigned position, no actions/changes will be taken
Sets to the System index value.
•When setting the A/B/C/D switch to an indexed System assigned position, the radio
System S election
•When changing away from a System assigned position, no actions/changes will be
user-programmable buttons.
If a user then changes to a different system or zone via another method (menu,
button, etc.), it will override the Zone selection switch setting accordingly and not
require it to remain in the zone where the switch assignment is set.
by the radio.
sets, but does not “hold,” that System. This has the resulting effects:
This sets the channel knob to be system-based channel sele ctio n, just like
selecting a system from the main “Zone” menu or ramping up/down using the side
user-programmable buttons.
If a user then changes to a different system or zone via another method (menu,
button, etc.), it will override the System selection switch sett in g accord ing ly and not
require it to remain in the system where the switch assignment is set.
taken by the radio.
7.5 PROGRAMMABLE ICONS
7.5.1 Top display
The top display has space for up to seven configurable icons, which can be programmed to display any of
the following:
• Blank
• Signal Strength
• Battery Status
• Bluetooth enabled
• Encryption enabled
• Scan/Vote Scan enabled
• Talkaround enabled
95
14221-1800-2000, Rev. F
• Emergency mode active
The radio can be programmed to cha nge the color of t he top display b acklight rela tive to the curr ently
selected channel/group. The backlight remains the color programmed for the currently selected
channel/group except during an emergency, in which case the color changes to orange.
7.5.2 Front display
The front display has space for up to 10 configurable icons, which can be programmed to display any of
the following:
• Blank
• Signal Strength
• Battery Status
• Bluetooth enabled
• Encryption enabled
• Global Encryption
• Talkaround enabled
• TX Disabled
• Tones Disabled
• PTT Disabled
• Speaker Muted
• Monitor
• OTAR Status (Disabled, Registering, Registered, Rekeying)
• TX Power level (Low/High/RX Only)
• GPS Status
• VDOC
• Failsoft
• Data Status (TX/RX)
• Alert(s)
• RX Mail
• Noise Cancellation Enabled
• Type 99 Enabled
• Conventional Site Status (Unregistered/Registered)
96
14221-1800-2000, Rev. F
CHANNEL
FREQUENCY
SHIP
(MHZ)
SHORE
(MHZ)
1 1
T: 156.05
R: 160.65
T: 160.65
R: 156.05
International: Public Correspondence, Port Operations
1a
T/R:
156.05
T/R:
156.05
US: Port Operations and Commercial, Vessel Traffic Service (VTS). New
Orleans/Lower Mississippi area.
2 2
T: 156.10
R: 160.70
T: 160.70
R: 156.10
International: Public Correspondence, Port Operations
3 3
T: 156.15
R: 160.75
T: 160.75
R: 156.15
International: Public Correspondence, Port Operations
4
T: 156.20
R: 160.80
T: 160.80
R: 156.20
International: Public Correspondence, Port Operations
4a
T/R:
156.20
T/R:
156.20
Canada: Department Fisheries Ocean (DFO)/Canadian Coast Guard only in
British Columbia coast area. Commercial fishing in east coast area
5
T: 156.25
R: 160.85
T: 160.85
R: 156.25
International: Public Correspondence, Port Operations
5a 5a
T/R:
156.25
T/R:
156.25
US: Port Operations or VTS in Houston, New Orleans and Seattle areas.
6 6 6
T/R:
T/R:
US: Intership Safety
and aircraft.
7
T: 156.35
R: 160.95
T: 160.95
R: 156.35
International: Public Correspondence, Port Operations
7a 7a
T/R:
156.35
T/R:
156.35
US: Commercial
8 8 8
T/R:
T/R:
US: Commercial (Intership only)
Canada: Also assigned for intership in the Lake Winnipeg are a.
9 9 9
T/R:
T/R:
US: Boater Calling. Commercial and Non-Commercial.
maritime support operations.
8. REFERENCE
8.1 MARINE FREQUENCIES
Refer to Table 8-1: Marine Frequencies for a list of maritime frequencies per United States Coast Guard
(USCG), National Oceanic and Atmospheric Administration (NOAA), and Canadian Department
Fisheries and Oceans, August 2009:
• United States (US)
• International (Intl)
• Canada (CA)
Table 8-1: Marine Frequencies
US INTL CA
156.30
156.30
CHANNEL USAGE
International: Intership
Canada: May be used for search and rescue communications between ships
156.40
156.45
156.40
156.45
International: Intership
International: Intership, Port Operations
Canada: Commercial - Brit ish C olum bia coast ar ea.
May be used to communicate with aircraft and helicopters in predominantly
US: Environmental (Receive only). Used by Class C Emergency Position-
board communications.
16
16
16
T/R:
T/R:
US: International Distress, Safety and Calling. Ships required to carry radio,
Canada: International Distress, Safety and Calling
17
17
17
T/R:
T/R:
US: State Control
board communications.
18 T: 156.90
R: 161.50
T: 161.50
R: 156.90
International: Public Correspondence, Port Operations
18a 18a
T/R:
156.90
T/R:
156.90
US: Commercial
Canada: Towing - British Columbia coast area.
19 T: 156.95
R: 161.55*
T: 161.55*
R: 156.95
International: Public Correspondence, Port Operations
19a 19a
T/R:
T/R:
US: Commercial
area.
20
20
20
T: 157.00
T: 161.60
US: Port Operations (Duplex)
Canada: Port operations only with 1 watt maximum power.
US INTL CA
156.50
156.55
156.60
156.65
156.70
156.50
156.55
156.60
156.65
156.70
CHANNEL USAGE
International: Intership, Port Operations
Canada: Commercial - Brit ish C olum bia coast ar ea.
May also be used for communications with aircraft engaged in coordinated
International: Port Operations
Canada: VTS - British Columbia coast area.
International: Port Operations
Canada: VTS - British Columbia coast area.
maintain a listening watch on this channel in US waters.
International: Intership, Port Operations
Canada: VTS - British Columbia coast area.
International: Port Operations
Canada: VTS - British Columbia coast area.
156.75
156.80
156.85
156.95
156.75
156.80
156.85
156.95
Indicating Radio Beacons (EPIRBs).
International: Intership, Port Operations
Canada: Port operations and Ship Movement - British Columbia coast area.
All operations limited to 1-watt maximum power. May also be used for on-
US Coast Guard (USCG), and most coast stations maintain a listening watch
on this channel.
International: International Distress, Safety and Calling
International: Intership, Port Operations
Canada: Port operations and Ship Movement - British Columbia coast area.
All operations limited to 1 watt maximum power. May also be used for on-
Canada: DFO/Canadian Coast Guard. Pacific Pilots - British Columbia coast
R: 161.60
98
R: 157.00
International: Public Correspondence, Port Operations
14221-1800-2000, Rev. F
CHANNEL
FREQUENCY
SHIP
(MHZ)
SHORE
(MHZ)
20a
T/R:
157.00
T/R:
157.00
US: Port Operations
21 T: 157.05
R: 161.65*
T: 161.65*
R: 157.05
International: Public Correspondence, Port Operations
21a 21a
T/R:
157.05
T/R:
157.05
US: US Coast Guard only
Canada: DFO/Canadian Coast Guard only.
21b
- -
T/R:
161.65
22 T: 157.10
R: 161.70
T: 161.70
R: 157.10
International: Public Correspondence, Port Operations
22a 22a
T/R:
T/R:
US: Coast Guard Liaison and Maritime Safety Information Broadcasts.
Canadian Coast Guard stations only.
23
23
T: 157.15
R: 161.75
T: 161.75
R: 157.15
International: Public Correspondence, Port Operations