HARRIS TR 0136 E User Manual

Rhein Tech Laboratories, Inc. Client: Harris Corporation
360 Herndon Parkway Model: XG-15P UHF-H
Suite 1400 IDs: OWDTR-0136-E/3636B-0136
Herndon, VA 20170 Standards: FCC Parts 22/74/80/90/IC RSS-119
http://www.rheintech.com Report #: 2015156

Appendix N: Manuals
Please refer to the following pages for the Operator’s Manual and the Safety Manual.

84 of 102

Operator’s Manual

14221-1450-2000

Rev. B, Sep/15

XG-15P Series

Portable Radios

14221-1450-2000, Rev. B

REV

DATE

REASON FOR REVISION

-

May/15

Initial release.

A

Aug/15

Added VHF split.

B

Sep/15

Added UHF split.

This product conforms to the European Union WEEE Directive 2012/19/EU. Do not dispose of this product in a public landfill. Take it to a
recycling center at the end of its life.

Copyright © 2015 Harris Corporation. All rights reserved.

Harris Corporation, Public Safety and Professional Communications (PSPC) Business continually evaluates its technical publications for
completeness, technical accuracy, and organization. You can assist in this process by submitting your comments and suggestions to the
following:
Harris Corporation fax your comments to: 1-434-455-6851
PSPC Business or
Technical Publications e-mail us at: [e-mail]
221 Jefferson Ridge Parkway
Lynchburg, VA 24501

ACKNOWLEDGEMENTS

The software contained in this device is copyrighted by Harris Corporation Unpublished rights are reserved under the copyright laws of the
United States.

This device is made under license under one or more of the following US patents: 4,590,473; 4,636,791; 5,148,482; 5,185,796; 5,271,017;
5,377,229; 4,716,407; 4,972,460; 5,502,767; 5,146,497; 5,164,986; 5,185,795; 5,226,084; 5,247,579; ; 5,491,772; 5,517,511; 5,630,011;
5,649,050; 5,701,390; 5,715,365; 5,754,974; 5,826,222; 5,870,405; 6,161,089; and 6,199,037 B1. DVSI claims certain rights, including
patent rights under aforementioned U.S. patents, and under other U.S. and foreign patents and patents pending. Any use of this software or
technology requires a separate written license from DVSI.

CREDITS!

Harris Corporation and assuredcommunications are registered trademarks and ProScan and Failsoft are trademarks of Harris Corporation.
RBRC and 1-800-8-BATTERY are registered trademarks of Rechargeable Battery Recycling Corporation.
AMBE is a registered trademark and IMBE, AMBE+, and AMBE+2 are trademarks of Digital Voice Systems, Inc.
TORX is a registered trademark of CAMCAR division of TEXTRON, Inc.
All other product and brand names are trademarks, registered trademarks, or service marks of their respective holders.

NOTICE!

The material contained herein is subject to U.S. export approval. No export or re-export is permitted without written approval from the U.S.
Government. Rated: EAR99; in accordance with U.S. Dept. of Commerce regulations 15CFR774, Export Administration Regulations.

Information and descriptions contained herein are the property of Harris Corporation. Such information and descriptions may not be copied
or reproduced by any means, or disseminated or distributed without the express prior written permission of Harris Corporation, PSPC
Business, 221 Jefferson Ridge Parkway, Lynchburg, VA 24501.

This manual covers Harris Corporation products manufactured and sold by Harris Corporation.

The voice coding technology embodied in this product is protected by intellectual property rights including patent rights, copyrights, and
trade secrets of Digital Voice Systems, Inc. The user of this technology is explicitly prohibited from attempting to decompile, reverse
engineer, or disassemble the Object Code, or in any other way convert the Object Code into human-readable form.

Repairs to this equipment should be made only by an authorized service technician or facility designated by the supplier. Changes or
modifications not expressly approved by Harris Corporation could void the user’s authority to operate the equipment.

This manual is published by Harris Corporation, without any warranty. Improvements and changes to this manual necessitated by
typographical errors, inaccuracies of current information, or improvements to programs and/or equipment, may be made by Harris
Corporation, at any time and without notice. Such changes will be incorporated into new editions of this manual. No part of this manual
may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, for any
purpose, without the express written permission of Harris Corporation.

2

14221-1450-2000, Rev. B

TABLE OF CONTENTS

Page

1. REGULATORY AND SAFETY INFORMATION ............................................................................................. 6

1.1 SAFETY CONVENTIONS ........................................................................................................................ 6

1.2 SAFETY TRAINING INFORMATION ................................................................................................ ..... 6

1.2.1 RF Exposure Guidelines ............................................................................................................... 7

1.2.2 Electromagnetic Interference/Compatibility ................................................................................. 8

1.3 REGULATORY APPROVALS .................................................................................................................. 8

1.3.1 Part 15 ........................................................................................................................................... 8

1.3.2 Industry Canada ............................................................................................................................ 8

1.4 OPERATING TIPS ..................................................................................................................................... 8

1.5 EFFICIENT RADIO OPERATION ............................................................................................................ 9

1.5.1 Antenna Care and Replacement .................................................................................................... 9

1.5.2 Electronic Devices ........................................................................................................................ 9

1.5.3 Aircraft .......................................................................................................................................... 9

1.5.4 Electric Blasting Caps ................................................................................................................... 9

1.5.5 Potentially Explosive Atmospheres ............................................................................................ 10

2. RENSEIGNEMENTS SUR LA RÉGLEMENTATION ET SÉCURITÉ........................................................ 11

2.1 CONVENTIONS SUR LES SYMBOLES DE SÉCURITÉ ..................................................................... 11

2.2 RENSEIGNEMENTS SUR LA FORMATION SUR LA SÉCURITÉ ..................................................... 11

2.2.1 Directives sur l’exposition aux RF .............................................................................................. 12

2.2.2 Interférence/Compatibilité Électromagnétique ........................................................................... 13

2.3 INTERFÉRENCE DES RADIOFRÉQUENCES ...................................................................................... 13

2.3.1 Partie 15 de la FCC ..................................................................................................................... 13

2.3.2 Industrie Canada ......................................................................................................................... 13

2.4 CONSEILS D’UTILISATION .................................................................................................................. 13

2.4.1 Utilisation Efficace de la Radio .................................................................................................. 14

3. CLEANING .......................................................................................................................................................... 16

4. BATTERIES ......................................................................................................................................................... 17

4.1 BATTERY CARE/MAINTENANCE ....................................................................................................... 17

4.2 STORING LI-ION BATTERY PACKS ................................................................................................... 17

4.3 CHARGING BATTERY PACKS ............................................................................................................. 17

4.4 CHANGING THE BATTERY PACK ...................................................................................................... 18

4.4.1 Removing the Battery Pack ......................................................................................................... 18

4.4.2 Attaching the Battery Pack.......................................................................................................... 19

4.5 BATTERY DISPOSAL ............................................................................................................................ 19

5. INTRODUCTION ................................................................................................................................ ................ 20

5.1 WATER RESISTANCE............................................................................................................................ 21

5.2 UNIVERSAL DEVICE CONNECTOR ................................................................................................... 21

6. OPTIONS AND ACCESSORIES ....................................................................................................................... 22

7. OPERATION ........................................................................................................................................................ 25

7.1 TURNING ON THE RADIO .................................................................................................................... 25

7.2 CONTROLS .............................................................................................................................................. 25

7.2.1 Buttons, Knobs, and Switch ........................................................................................................ 26

7.2.2 Keypad ........................................................................................................................................ 26

7.3 DISPLAY .................................................................................................................................................. 27

7.4 RADIO STATUS ICONS ......................................................................................................................... 28

7.5 TRI-COLOR LED ..................................................................................................................................... 28

7.6 RADIO STATUS MESSAGES ................................................................................................................ 29

7.7 ERROR MESSAGES ................................................................................................................................ 29

7.8 ALERT TONES ........................................................................................................................................ 30

3

14221-1450-2000, Rev. B

TABLE OF CONTENTS

Page

7.9 VOICE ANNUNCIATION ....................................................................................................................... 30

7.10 SYSTEM/ZONE SELECTION ................................................................................................................. 30

7.11 GROUP/CHANNEL SELECTION ........................................................................................................... 31

7.12 MODIFY SCAN LIST .............................................................................................................................. 31

7.13 MENU ....................................................................................................................................................... 32

7.14 MENU ITEM SELECTION PROCESS .................................................................................................... 32

7.15 BACKLIGHT ON/OFF ............................................................................................................................. 34

7.16 CONTRAST ADJUST .............................................................................................................................. 34

7.17 DECLARING AN EMERGENCY ............................................................................................................ 35

7.18 LOCKING/UNLOCKING KEYPAD ....................................................................................................... 35

7.19 HIGH/LOW POWER ADJUSTMENT ..................................................................................................... 35

7.19.1 Using the Menu Button ............................................................................................................... 35

7.19.2 Using the Pre-Programmed Option Button ................................................................................. 35

7.20 ENCRYPTION .......................................................................................................................................... 35

7.20.1 Displaying the Currently Used Cryptographic Key Number....................................................... 36

7.20.2 Key Zero ...................................................................................................................................... 36

7.20.3 Receiving an Encrypted Call ....................................................................................................... 36

7.20.4 Transmitting an Encrypted Call................................................................................................ ... 36

7.20.5 Emergencies on Encrypted Group ............................................................................................... 37

7.21 SCAN OPERATION ................................................................................................................................. 37

7.21.1 Turning Scan On and Off ............................................................................................................ 37

7.21.2 Add Groups and Channels to a Scan List ................................ .................................................... 37

7.21.3 Deleting Groups from a Scan List ............................................................................................... 38

7.21.4 Nuisance Delete ........................................................................................................................... 38

7.22 SYSTEM SCAN (P25 TRUNKED) .......................................................................................................... 38

7.22.1 Wide Area System Scanning ....................................................................................................... 38

7.22.2 Priority System Scan ................................................................................................................... 39

7.22.3 ProScan ....................................................................................................................................... 39

7.23 EMERGENCY OPERATION ................................................................................................................... 39

7.23.1 Receiving an Emergency Call ..................................................................................................... 39

7.23.2 Declaring an Emergency Call ...................................................................................................... 40

7.24 MIXED SYSTEM ZONES........................................................................................................................ 40

7.25 CALLER ID .............................................................................................................................................. 40

7.26 STEALTH MODE ..................................................................................................................................... 41

7.26.1 Mixed Zone Scan ........................................................................................................................ 41

7.27 INDIVIDUAL CALLS (P25 MODES) ..................................................................................................... 42

7.27.1 Receiving and Responding to an Individual Call ........................................................................ 42

7.27.2 Sending an Individual Call .......................................................................................................... 43

7.27.3 Call Storage Lists ........................................................................................................................ 44

7.28 TELEPHONE INTERCONNECT CALLS (P25 TRUNKED) ................................................................. 44

7.28.1 Receiving a Telephone Interconnect Call .................................................................................... 44

7.28.2 Sending a Telephone Interconnect Call ....................................................................................... 45

7.28.3 Dual-Tone Multi-Frequency: Overdial ........................................................................................ 45

7.29 PRE-STORING INDIVIDUAL AND TELEPHONE INTERCONNECT CALLS FROM THE

KEYPAD ................................................................................................................................................... 46

7.30 STATUS/MESSAGE OPERATION (P25 MODES) ................................................................................ 47

7.30.1 Status Operation .......................................................................................................................... 47

7.30.2 Message Operation ...................................................................................................................... 47

7.31 MACRO KEY OPERATION .................................................................................................................... 48

7.32 TYPE 99 OPERATION (ANALOG CONVENTIONAL) ........................................................................ 48

7.32.1 Type 99 with or without Channel Guard ..................................................................................... 48

7.32.2 Resetting Type 99 after a Call ..................................................................................................... 48

7.32.3 Type 99 Disable after PTT .......................................................................................................... 49

4

14221-1450-2000, Rev. B

TABLE OF CONTENTS

Page

7.33 AUDIO PLAYBACK ............................................................................................................................... 49

7.34 RADIO TEXTLINK OPERATION .......................................................................................................... 49

7.34.1 Send TextLink Messages ............................................................................................................ 49

7.34.2 View Received TextLink Messages ............................................................................................ 49

7.34.3 Delete TextLink Messages .......................................................................................................... 50

7.34.4 View the Current Time ............................................................................................................... 50

7.35 VIEW GPS INFORMATION ................................................................................................................... 50

7.36 CONTROL AND STATUS SERVICES ................................................................................................... 50

8. CUSTOMER SERVICE ...................................................................................................................................... 51

8.1 CUSTOMER CARE ................................................................................................................................. 51

8.2 TECHNICAL ASSISTANCE ................................................................................................................... 51

9. BASIC TROUBLESHOOTING .......................................................................................................................... 52

10. WARRANTY ........................................................................................................................................................ 52

FIGURES

Figure 4-1: Removing the Battery Pack ......................................................................................................................... 18

Figure 4-2: Attaching the Battery Pack .......................................................................................................................... 19

Figure 5-1: XG-15P Radio ............................................................................................................................................. 20

Figure 5-2: XG-15P 15-Pin Universal Device Connector .............................................................................................. 21

Figure 7-1: Top View ..................................................................................................................................................... 25

Figure 7-2: Side View .................................................................................................................................................... 25

Figure 7-3: XG-15P Keypad........................................................................................................................................... 26

Figure 7-4: Sample Radio Display ................................................................................................................................. 27

Figure 7-5: Menu Display .............................................................................................................................................. 32

Figure 7-6: Backlight Menu Item Selection Parameter .................................................................................................. 32

Figure 7-7: Backlight Menu Display .............................................................................................................................. 33

Figure 7-8: System Encryption Key Display .................................................................................................................. 36

Figure 7-9: Group/Channel Encryption Key Display ..................................................................................................... 36

Figure 7-10: Calls Received Lists .................................................................................................................................. 43

Figure 7-11: WHC Individual Call Display .................................................................................................................... 43

Figure 7-12: Calls Received and Personality Lists ......................................................................................................... 44

TABLES

Table 1-1: RF Exposure Compliance Testing Distances .................................................................................................. 8

Table 6-1: Options and Accessories ............................................................................................................................... 22

Table 7-1: Buttons, Knobs, and Switch Functions ......................................................................................................... 26

Table 7-2: XG-15P Keypad Functions ........................................................................................................................... 27

Table 7-3: Status Icon Descriptions ................................................................................................................................ 28

Table 7-4: Alert Tones .................................................................................................................................................... 30

Table 7-5: Menu Item Information ................................................................................................................................. 33

Table 9-1: Troubleshooting ............................................................................................................................................ 52

5

14221-1450-2000, Rev. B

The WARNING symbol calls attention to a procedure, practice, or the like, which, if
not correctly performed or adhered to, could result in personal injury. Do not
proceed beyond a WARNING symbol until the conditions identified are fully
understood or met.

The CAUTION symbol calls attention to an operating procedure, practice, or the like,
which, if not performed correctly or adhered to, could result in damage to the equipment
or severely degrade the equipment performance.

The NOTE symbol calls attention to supplemental information, which may improve
system performance or clarify a process or procedure.

The Harris XG-15P portable radio generates RF electromagnetic energy during
transmit mode. This radio is designed for and classified as “Occupational Use

Only,” meaning it must be used only during the course of employment by

individuals aware of the hazards and the ways to minimize such hazards. This

radio is NOT intended for use by the “General Population” in an uncontrolled

environment.

WARNING

CAUTION

NOTE

WARNING

1. REGULATORY AND SAFETY INFORMATION

1.1 SAFETY CONVENTIONS

The following conventions are used throughout this manual to alert the user to general safety precautions
that must be observed during all phases of operation, service, and repair of this product. Failure to comply
with these precautions or with specific warning elsewhere in this manual violates safety standards of
design, manufacture, and intended use of the product. Harris assumes no liability for the customer’s
failure to comply with these standards.

1.2 SAFETY TRAINING INFORMATION

The XG-15P portable radio has been tested and complies with the FCC RF exposure limits for

“Occupational Use Only.” In addition, this Harris radio complies with the following Standards and

Guidelines with regard to RF energy and electromagnetic energy levels and evaluation of such levels for
exposure to humans:

 FCC OET Bulletin 65 Edition 97-01 Supplement C, Evaluating Compliance with FCC Guidelines for

Human Exposure to Radio Frequency Electromagnetic Fields.

 American National Standards Institute (C95.1 – 1992), IEEE Standard for Safety Levels with Respect

to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz.

 American National Standards Institute (C95.3 – 1992), IEEE Recommended Practice for the

Measurement of Potentially Hazardous Electromagnetic Fields – RF and Microwave.

6

14221-1450-2000, Rev. B

To ensure that exposure to RF electromagnetic energy is within the FCC allowable
limits for occupational use and/or the exposure limit values in Annex A of EU Directive
2004/40/EC, always adhere to the following guidelines:

CAUTION

 IC Standard RSS-102, Issue 4, 2010: Spectrum Management and Telecommunications Radio

Standards Specification. Radiofrequency Exposure Compliance of Radiocommunication Apparatus
(All Frequency Bands).

 DIRECTIVE 2004/40/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 29

April 2004 on the minimum health and safety requirements regarding the exposure of workers to the
risks arising from physical agents (electromagnetic fields) and amended by:

 Directive 2007/30/EC of the European Parliament and of the Council of 20 June 2007
 Directive 2008/46/EC of the European Parliament and of the Council of 23 April 2008
 Regulation (EC) No 1137/2008 of the European Parliament and of the Council of 22 October

2008

 Directive 2012/11/EU of the European Parliament and of the Council of 19 April 2012

1.2.1 RF Exposure Guidelines

 DO NOT operate the radio without a proper antenna attached, as this may damage the radio and may

also cause the FCC RF exposure limits and/or the exposure limit values in Annex A of EU Directive
2004/40/EC to be exceeded. A proper antenna is the antenna supplied with this radio by Harris or an
antenna specifically authorized by Harris for use with this radio. (Refer to Table 6-1.)

 DO NOT transmit for more than 50% of total radio use time (“50% duty cycle”). Transmitting more

than 50% of the time can cause FCC RF exposure compliance requirements and/or the exposure limit
values in Annex A of EU Directive 2004/40/EC to be exceeded. The radio is transmitting when the
“TX” indicator appears in the display. The radio will transmit by pressing the “PTT” (Push-To-Talk)
button.

 ALWAYS transmit using low power when possible. In addition to conserving battery charge, low

power can reduce RF exposure.

 ALWAYS use Harris authorized accessories (antennas, batteries, belt clips, speaker/mics, etc). Use of

unauthorized accessories may cause the FCC Occupational/Controlled Exposure RF compliance
requirements and/or the exposure limit values in Annex A of EU Directive 2004/40/EC to be
exceeded. (Refer to Table 1-1.)

 As noted in Table 1-1, ALWAYS keep the housing of the transmitter AT LEAST 1.4 cm (0.55

inches) from the body and at least 2.5 cm (0.98 inches) from the face when transmitting to ensure
FCC RF exposure compliance requirements and/or the exposure limit values in Annex A of EU
Directive 2004/40/EC are not exceeded. However, to provide the best sound quality to the recipients
of your transmission, Harris recommends you hold the microphone at least 5 cm (2 inches) from
mouth, and slightly off to one side.

7

14221-1450-2000, Rev. B

RADIO FREQUENCY (MHz)

TESTED DISTANCES

(worst case scenario)

Body1

Face

700/800 MHz
(768.0125 - 775.9875)
(798.0125 - 804.9875)

(806.0125 - 815.09875)

(851.0125 - 860.9875)

1.4 cm (0.55 in.)

2.5 cm (0.98 in.)

VHF (136 - 174 MHz)

With Body-Worn Accessory:

0 cm (0 in.)

2.5 cm (0.98 in.)

UHF (440-512MHz)

With Body-Worn Accessory:

0 cm (0 in.)

2.5 cm

(0.98 in)

Table 1-1: RF Exposure Compliance Testing Distances

The information in this section provides the information needed to make the user aware of RF exposure,
and what to do to assure that this radio operates within the FCC RF exposure limits and/or the exposure
limit values in Annex A of EU Directive 2004/40/EC.

1.2.2 Electromagnetic Interference/Compatibility

During transmissions, this Harris radio generates RF energy that can possibly cause interference with
other devices or systems. To avoid such interference, turn off the radio in areas where signs are posted to
do so. DO NOT operate the transmitter in areas that are sensitive to electromagnetic radiation such as
hospitals, aircraft, and blasting sites.

1.3 REGULATORY APPROVALS

1.3.1 Part 15

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause undesired

operation.

1.3.2 Industry Canada

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.

1.4 OPERATING TIPS

Antenna location and condition are important when operating a portable radio. Operating the radio in low
lying areas or terrain, under power lines or bridges, inside of a vehicle, or in a metal framed building can
severely reduce the range of the unit. Mountains can also reduce the range of the unit.

In areas where transmission or reception is poor, some improvement may be obtained by ensuring that the
antenna is vertical. Moving a few yards in another direction or moving to a higher elevation may also
improve communications. Vehicular operation can be aided with the use of an externally mounted
antenna.

1

This is worst case based on the thinnest body mount accessory (belt clip).

8

14221-1450-2000, Rev. B

Do NOT hold onto the antenna when the radio is powered on!

Do not use the portable radio with a damaged or missing antenna. A minor burn
may result if a damaged antenna comes into contact with the skin. Replace a
damaged antenna immediately. Operating a portable radio with the antenna missing
could cause personal injury, damage the radio, and may violate FCC regulations.

Use only the supplied or approved antenna. Unauthorized antennas, modifications, or
attachments could cause damage to the radio unit and may violate FCC regulations. (Refer
to Table 6-1.)

RF energy from portable radios may affect some electronic equipment. Most modern
electronic equipment in cars, hospitals, homes, etc. is shielded from RF energy. However,
in areas in which you are instructed to turn off two-way radio equipment, always observe
the rules. If in doubt, turn it off!

 Always turn off a portable radio before boarding any aircraft!
 Use it on the ground only with crew permission.
 DO NOT use while in-flight!!

To prevent accidental detonation of electric blasting caps, DO NOT use two-way
radios within 1000 feet of blasting operations. Always obey the "Turn Off Two-Way
Radios" signs posted where electric blasting caps are being used. (OSHA Standard:

1926.900)

WARNING

WARNING

CAUTION

CAUTION

WARNING

WARNING

Battery condition is another important factor in the trouble free operation of a portable radio. Always
properly charge the battery.

1.5 EFFICIENT RADIO OPERATION

Keep the antenna in a vertical position when receiving or transmitting a message.

1.5.1 Antenna Care and Replacement

1.5.2 Electronic Devices

1.5.3 Aircraft

1.5.4 Electric Blasting Caps

9

14221-1450-2000, Rev. B

Areas with potentially explosive atmospheres are often, but not always, clearly
marked. These may be fuelling areas, such as gas stations, fuel or chemical transfer
or storage facilities, and areas where the air contains chemicals or particles, such as
grain, dust, or metal powders.

Sparks in such areas could cause an explosion or fire resulting in bodily injury or
even death.

Turn off two-way radios when in any area with a potentially explosive atmosphere. It
is rare, but not impossible that a radio or its accessories could generate sparks.

WARNING

1.5.5 Potentially Explosive Atmospheres

10

14221-1450-2000, Rev. B

MISE EN GARDE

Le symbole MISE EN GARDE attire l’attention sur une procédure ou une
pratique qui, si elle n’est pas correctement effectuée ou observée, pourrait

entraîner une blessure personnelle. Ne pas poursuivre au-delà d’un symbole de
MISE EN GARDE avant que les conditions identifiées soient complètement
comprises ou satisfaites.

AVERTISSEMENT

Le symbole AVERTISSEMENT attire l’attention sur une procédure ou une pratique
opérationnelle qui, si elle n’est pas correctement effectuée ou observée, pourrait
entraîner un bris d’équipement ou une importante baisse de rendement de l’équipement.

REMARQUE

Le symbole REMARQUE attire l’attention sur des renseignements supplémentaires qui
peuvent améliorer le rendement du système ou clarifier un processus ou une procédure.

MISE EN GARDE

La radio portative Harris XG-15P produit de l’énergie électromagnétique des RF
lorsqu’en mode de transmission. Cette radio est conçue et classée pour une
« Utilisation professionnelle seulement », ce qui signifie qu’elle ne doit être utilisée
que dans le cadre d’un emploi par des individus conscients des risques et des
moyens de limiter ceux-ci. Cette radio N’EST PAS conçue pour une utilisation par
la « Population générale » dans un environnement non contrôlé.

2. RENSEIGNEMENTS SUR LA RÉGLEMENTATION ET
SÉCURITÉ

2.1 CONVENTIONS SUR LES SYMBOLES DE SÉCURITÉ

Les conventions suivantes sont utilisées dans le présent manuel pour avertir l’utilisateur des précautions

générales de sécurité qui doivent être observées pendant toutes les phases d’opération, d’entretien et de

réparation de ce produit. Le non-respect de ces précautions ou d’avertissements précisés ailleurs enfreint

les normes de sécurité de la conception, de la fabrication et de l’utilisation prévue du produit. Harris

n’assume aucune responsabilité pour le non-respect de ces normes par le client.

2.2 RENSEIGNEMENTS SUR LA FORMATION SUR LA SÉCURITÉ

La radio portative XG-15P a été testée et est conforme aux limites d’exposition aux RF de la FCC pour
une « Utilisation professionnelle seulement ». De plus, cette radio Harris est conforme aux normes et
directives suivantes quant à l’énergie des RF et aux niveaux d’énergie électromagnétique, ainsi qu’à
l’évaluation de ces niveaux pour l’exposition aux humains :

 Bulletin 65 du OET de la FCC, édition 97-01, supplément C, portant sur l’évaluation de la conformité

aux directives de la FCC quant à l’exposition humaine aux champs électromagnétiques des
radiofréquences.

 American National Standards Institute (C95.1 – 1992), norme de l’IEEE sur les niveaux sécuritaires

d’exposition humaine aux champs électromagnétiques des radiofréquences, 3 kHz à 300 GHz.

 American National Standards Institute (C95.3 – 1992), pratique recommandée par l’IEEE pour la

mesure des champs électromagnétiques potentiellement dangereux – RF et micro-ondes.

11

14221-1450-2000, Rev. B

AVERTISSEMENT

Pour s’assurer que l’exposition à l’énergie électromagnétique des RF se situe dans les
limites acceptables de la FCC pour l’utilisation professionnelle, respectez toujours les
directives suivantes :

 IC la norme RSS-102, Numéro 4, 2010: Gestion du spectre et télécommunications normes

radioélectriques. L'exposition aux radiofréquences Conformité des appareils de radiocommunication
(toutes bandes de fréquences).

2.2.1 Directives sur l’exposition aux RF

 N’utilisez PAS la radio sans qu’une antenne appropriée y soit connectée, car ceci peut endommager la

radio et également causer un dépassement des limites d’exposition aux RF de la FCC. Une antenne
appropriée est celle fournie par Harris avec cette radio, ou une antenne spécifiquement autorisée par
Harris pour être utilisée avec cette radio. (Reportez-vous à Table 6-1.)

 Ne transmettez PAS pendant plus de 50 % de la durée d’utilisation totale de la radio (« cycle de

service de 50 % »). La transmission pendant plus de 50 % du temps peut causer un dépassement des
exigences de conformité de la FCC en matière d’exposition aux RF. La radio transmet lorsque
l’indicateur « TX » apparaît sur l’affichage. La radio transmet lorsqu’on appuie sur le bouton « PTT »
(bouton de microphone).

 Transmettez TOUJOURS en basse puissance lorsque possible. En plus de préserver la charge de la

pile, une faible puissance réduit l’exposition aux RF.

 Utilisez TOUJOURS des accessoires autorisés Harris (antennes, piles, pinces de ceinture, haut-

parleurs/micros, etc.). L’utilisation d’accessoires non autorisés peut entraîner un dépassement des
exigences de conformité pour une exposition aux RF professionnelle ou contrôlée de la FCC.
(Reportez-vous à Tableau 2-1.)

 Tel qu’indiqué dans Tableau 2-1, conservez TOUJOURS l’appareil et son antenne à AU MOINS

1,4 cm du corps, et à au moins 2,5 cm du visage pendant la transmission, pour vous assurer de ne pas
dépasser les exigences de conformité de la FCC en matière d’exposition aux RF. Cependant, pour
offrir la meilleure qualité sonore aux auditeurs de votre transmission, Harris recommande de tenir le
microphone à au moins 5 cm de votre bouche et légèrement déplacé sur un côté.

12

14221-1450-2000, Rev. B

RADIO FRÉQUENCES

DISTANCES TESTÉES

(pire des scénarios)

Corps2

Visage

700/800 MHz
(768.0125 - 775.9875)
(798.0125 - 804.9875)

(806.0125 - 815.09875)

(851.0125 - 860.9875)

1,4 cm

2,5 cm

VHF (136 - 174 MHz)

avec l'accessoire porté

sur le corps:

0 cm (0 in.)

2,5 cm

UHF (440-512MHz)

avec l'accessoire porté

sur le corps:

0 cm (0 in.)

2,5 cm

Tableau 2-1: Distances de test de conformité des expositions aux RF

Dans cette section figurent les renseignements nécessaires pour sensibiliser l’utilisateur à l’exposition aux
RF et sur ce qu’il faut faire pour s’assurer que cette radio fonctionne dans les limites d’exposition aux RF
de la FCC.

2.2.2 Interférence/Compatibilité Électromagnétique

Pendant les transmissions, cette radio Harris produit de l’énergie des RF qui peut causer de l’interférence
avec d’autres appareils ou systèmes. Pour éviter de telles interférences, fermez la radio dans les zones où
il est indiqué de le faire. N’utilisez PAS le transmetteur dans des zones sensibles aux radiations
électromagnétiques, comme les hôpitaux, les avions et les sites de détonation.

2.3 INTERFÉRENCE DES RADIOFRÉQUENCES

2.3.1 Partie 15 de la FCC

Cet appareil est conforme à la Partie 15 de la réglementation de la FCC. Le fonctionnement est soumis
aux deux conditions suivantes :

1. Cet appareil ne doit pas causer une interférence nuisible; et

2. Cet appareil doit accepter toute interférence reçue, y compris une interférence qui peut causer un

fonctionnement non souhaité.

2.3.2 Industrie Canada

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de
brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.

2.4 CONSEILS D’UTILISATION

L’emplacement et l’état de l’antenne sont importants pour l’utilisation d’une radio portative. L’utilisation
de la radio dans des zones de faible élévation, sous des lignes électriques ou des ponts, à l’intérieur d’un
véhicule ou dans un immeuble à ossature métallique, peut réduire la portée de l’appareil de manière
considérable. Les montagnes peuvent également réduire la portée de l’unité.

2

Ce est le pire des cas basée sur le corps plus mince monter accessoire (clip ceinture).

13

14221-1450-2000, Rev. B

MISE EN GARDE

Ne tenez PAS l’antenne lorsque la radio est allumée!

MISE EN GARDE

N’utilisez pas la radio portative si son antenne est endommagée ou absente. Une
brûlure légère peut se produire au contact d’une antenne endommagée avec la
peau. Remplacez immédiatement une antenne endommagée. L’utilisation d’une
radio portative alors que l’antenne est absente peut causer des blessures,
endommager la radio et pourrait enfreindre la réglementation de la FCC.

AVERTISSEMENT

Utilisez seulement l’antenne fournie ou une antenne approuvée. Des antennes non
autorisées, des modifications ou des ajouts à une antenne peuvent endommager la radio et
enfreindre la réglementation de la FCC. (Reportez-vous à Table 6-1.)

AVERTISSEMENT

L’énergie des RF provenant de radios portatives peut affecter certains appareils
électroniques. La majorité de l’équipement électronique moderne dans les voitures, les
hôpitaux, les maisons, etc. est blindé contre l’énergie des RF. Cependant, dans les zones
où l’on vous demande de fermer l’équipement de radio bidirectionnelle, respectez toujours
les règles. En cas de doute, éteignez-le!

MISE EN GARDE

 Éteignez toujours une radio portative avant d’embarquer à bord d’un avion!
 Ne l’utilisez au sol qu’avec la permission de l’équipage.
 NE l’utilisez PAS durant le vol!

Dans les zones où la transmission ou la réception est insatisfaisante, certaines améliorations peuvent être
obtenues en s’assurant que l’antenne est verticale. Se déplacer de quelques mètres dans une autre
direction ou à un emplacement plus élevé peut également améliorer les communications. L’utilisation
d’une antenne fixée à l’extérieur peut faciliter le fonctionnement dans un véhicule.

L’état de la pile est un autre facteur important d’une utilisation sans tracas d’une radio portative. Chargez
toujours correctement la pile.

2.4.1 Utilisation Efficace de la Radio

Gardez l’antenne dans une position verticale pendant la réception ou la transmission d’un message.

2.4.1.1 Entretien Et Remplacement De L’antenne

2.4.1.2 Appareils Électroniques

2.4.1.3 Avion

14

14221-1450-2000, Rev. B

MISE EN GARDE

Pour prévenir la détonation accidentelle des détonateurs électriques, n’utilisez PAS
de radios bidirectionnelles à moins de 305 m (1 000 pi) des opérations de détonation.
Respectez toujours les indications « Éteindre les radios bidirectionnelles » situées là
où des détonateurs électriques sont utilisés. (Norme OSHA : 1926.900)

MISE EN GARDE

Les zones ayant une atmosphère potentiellement explosive sont souvent, mais pas
toujours, identifiées clairement comme telles. Il peut s’agir de zones d’alimentation
en carburant, comme les postes d’essence, les installations de stockage ou de
transfert de carburant ou de produits chimiques, ainsi que les zones dont l’air
contient des produits chimiques ou des particules, comme des grains, de la poussière
ou des poudres métalliques.

Des étincelles dans de telles zones peuvent provoquer une explosion ou un incendie,
causant ainsi des blessures ou même la mort.

Éteignez les radios bidirectionnelles dans toute zone ayant une atmosphère
potentiellement explosive. Il est rare, mais pas impossible qu’une radio ou ses
accessoires produisent des étincelles.

2.4.1.4 Détonateurs Électriques

2.4.1.5 Atmosphère Potentiellement Explosive

15

14221-1450-2000, Rev. B

CAUTION

Do not use chemical cleaners, spray, or petroleum-based products. They may damage
the radio housing. We recommend using Chemtronics® Electro-Wash® PR (ES-1603) or
equivalent.

Do not spray cleaning solution directly on radio. To clean the radio in the speaker and
microphone areas, carefully wipe these areas but prevent the cleaning solution from
entering the speaker or microphone openings.

NOTE

3. CLEANING

Keep the exterior of the radio, battery, antenna, and radio accessories clean.

Periodically clean using the following procedures:

1. To remove dust and dirt, clean using a damp clean cloth (warm water and mild detergent soap).

2. Follow by wiping with a damp (warm water) clean cloth. Wipe dry with a clean cloth.

3. Remove the battery and wipe the battery and radio contacts using a soft dry cloth to remove dirt or

grease. This will ensure efficient power transfer from the battery to the radio.

4. Remove any accessories and clean the accessories Universal Device Connector (UDC) contacts using

a clean dry cloth. When the UDC is not in use, cover the connector with the protective dust cap to
prevent the build-up of dust or water particles.

5. If the radio is used in a harsh environment (such as driving rain, salt fog, etc.), it may be necessary to

periodically dry and clean the battery and radio contacts with a soft dry cloth or soft-bristle non­metallic brush.

For more rigorous cleaning, use the following procedure:

1. Apply the cleaning solution to a clean damp cloth and clean the radio.

2. Wipe off the radio with a clean damp cloth using mild warm soapy water.

3. Follow up by wiping off the radio with a clean damp cloth using warm water only.

4. Wipe dry with a clean cloth.

16

14221-1450-2000, Rev. B

WARNING

Do not disassemble or modify Lithium battery packs. Lithium battery packs are
equipped with built-in safety and protection features. Should these features be
disabled or tampered with in any way, the battery pack can leak electrolyte,
overheat, emit smoke, burst, and/or, ignite.

If the battery is ruptured or is leaking electrolyte that results in skin or eye contact
with the electrolyte, immediately flush the affected area with water. If the battery
electrolyte gets in the eyes, flush with water for 15 minutes and consult a physician
immediately.

WARNING

4. BATTERIES

The XG-15P series portable radios use rechargeable, recyclable Lithium-Ion (Li-Ion) batteries. Please
follow the directions below to maximize the useful life of the battery.

4.1 BATTERY CARE/MAINTENANCE

For information regarding the proper care of portable radio battery packs or establishing a battery
maintenance program, refer to ECR-7367 which may be ordered by calling toll free 1-800-368-3277
(international: 1-434-455-6403) or via https://premier.pspc.harris.com/infocenter/.

4.2 STORING LI-ION BATTERY PACKS

If a battery pack is expected to be idle for a month or more, it should be properly prepared. Li-Ion battery
packs should not be stored fully charged. Before storing the battery pack, discharge it to 40% capacity. If
the battery is not discharged prior to storage, its overall capacity may be reduced. Although all battery
packs experience some capacity loss during storage, the shelf life for Li-Ion battery packs is about three
months. However, note that any capacity drop which occurs during storage is permanent and cannot be
reversed. Li-Ion battery packs should be purchased and used immediately. They should not be stock­piled without a rotating stock plan.

4.3 CHARGING BATTERY PACKS

Battery chargers are available from Harris with nominal charge times. Combinations include single and
multi-position chargers.

Harris chargers are specifically designed for charging Lithium-Ion battery packs. The chargers are
chemistry-specific for the battery packs and automatically adjust the charging profiles accordingly. Refer
to the appropriate charger manual for specific operating instructions.

Observe the following guidelines when charging a battery pack:

 Avoid high temperature during charging.
 Discontinue use if the charger is overheating.
 Only charge Harris battery packs using a charger approved for use by Harris.
 Do not leave batteries in the charger indefinitely. For best results leave the battery in the charger for

two to six hours after the Green Ready LED comes on. Then place the battery pack into service and
fully discharge (as indicated by the radio low battery warning) before re-charging.

17