HARRIS TR-0049-E Users Manual
Installation Manual
MM-014714-001
Apr/08
M/A-COM
CS-7000 Control Station
MM-014714-001, Rev. P3
MANUAL REVISION HISTORY
REV. DATE REASON FOR CHANGE
– Apr/08 Original release.
M/A-COM Technical Publications would particularly appreciate feedback on any errors found in this document and
suggestions on how the document could be improved. Submit your comments and suggestions to:
Tyco Electronics Wireless Systems Segment
M/A-COM, Inc. or fax your comments to: 1-434-455-6851
Technical Publications
221 Jefferson Ridge Parkway or e-mail us at: techpubs@tycoelectronics.com
Lynchburg, VA 24501
CREDITS
M/A-COM, Inc. and/or Tyco Electronics may have patents, patent applications, trademarks, copyrights, or other intellectual
property rights covering subject matter in this document. Except as expressly provided in any written licen se agreement from
M/A-COM, the furnishing of this document does not give you any license to these patents, trademarks, copyrights, or other
intellectual property.
The software contained in this device is copyrighted by M/A-COM, Inc. Unpublished rights are reserved under the copyright
laws of the United States.
This device made under license under one or more of the following U.S. Patents: 4,590,473; 4,636,791; 5,148,482;
5,185,796; 5,271,017; 5, 3 7 7,229; 4,716,407; 4,972, 460; 5,502,767; 5,146,4 97; 5,164,986; 5,185,795
The voice coding technology embodied in this product is protected by intellectual property rights including patent rights,
copyrights, and trade secrets of Digital Voice Systems, Inc. The user of this technology is explicitly prohibited from
attempting to decompile, reverse engineer, or disassemble the Object Code, or in any other way convert the Object Code into
human-readable form.
OpenSky
Bird is a registered trademark of Bird Electronic Corporation. Microsoft
®
and EDACS® are registered trademarks of M/A-COM, Inc.
®
and Windows® are registered trademarks of
Microsoft Corporation.
NOTICE!
This manual covers M/A-COM products manufactured and sold by M/A-COM, Inc.
Repairs to this equipment should be made only by an authorized service technician or facility designated b y the supp lier. Any
repairs, alterations or substitution of recommended parts made by the user to this equipment not approved by the
manufacturer could void the user’s authority to operate the equipment in addition to the manufacturer’s warranty.
M/A-COM recommends the buyer use only M/A-COM authorized representatives to install and service this product. The
warranties provided to buyer under the terms of sale shall be null and void if this product is installed or serviced imp roperly
and M/A-COM shall have no further obligation to the buyer for any damage caused to the product or to any person or
personal property.
This product conforms to the European Union WEEE Directive 2002/96/EC. Do not dispose of this product in a
public landfill. Take it to a recycling center at the end of its life.
This manual is published by M/A-COM, Inc. without any warranty. Improvements and changes to this manual necessitated
by typographical errors, inaccuracies of current information, or improvements to programs and/or equipment, may be made
by M/A-COM, Inc., at any time and without notice. Such changes will be incorpor ated into new editions of this manual. No
part of this manual may be reproduced or transmitted in any form or by any means, electronic or mechanical, including
photocopying and recording, for any purpose, without the express written permission of M/A-COM, Inc.
Copyright© 2008, M/A-COM, Inc. All rights reserved.
2
MM-014714-001, Rev. P3
TABLE OF CONTENTS
Section Page
1 REGULATORY AND SAFETY INFORMATION...................................................................................6
1.1 MAXIMUM
1.1.1 Determining MPE Radius ...........................................................................................................6
1.1.2 Safety Training Information........................................................................................................6
1.2 SAFETY
1.3 IMPORTANT
2 SPECIFICATIONS.......................................................................................................................................9
3 INTRODUCTION.......................................................................................................................................12
3.1 VOICE
3.2 OPTIONAL
3.2.1 Intercom Operation ...................................................................................................................13
3.3 RELATED
3.4 TECHNICAL
3.5 CUSTOMER
4 UNPACKING AND CHECKING EQUIPMENT....................................................................................15
4.1 MATERIALS.......................................................................................................................................15
4.2 MATERIAL
PERMISSIBLE EXPOSURE LIMITS..............................................................................6
SYMBOL CONVENTIONS...................................................................................................7
SAFETY INSTRUCTIONS............................................................................................8
OPERATION...........................................................................................................................13
REMOTE CONTROL BOARD.......................................................................................13
DOCUMENTATION........................................................................................................13
ASSISTANCE...............................................................................................................14
RESOURCE CENTER...................................................................................................14
INSPECTION .................................................................................................................15
5 INSTALLATION........................................................................................................................................17
5.1 REQUIRED
TOOLS AND EQUIPMENT...........................................................................................17
5.1.1 Tools and Shop Supplies Required to Install the CS-7000 .......................................................17
5.1.2 Equipment Required for CS-7000 Configuration......................................................................17
5.2 PLANNING
5.3 CS-7000
THE CS-7000 INSTALLATION.....................................................................................17
INSTALLATION..................................................................................................................18
5.3.1 Desktop Installations.................................................................................................................18
5.3.2 Rack-Mount Installation............................................................................................................18
5.3.3 AC Power Connection...............................................................................................................19
5.3.4 AC Fuse Replacement...............................................................................................................19
5.4 ANTENNA
INSTALLATION.............................................................................................................20
5.4.1 RF Safety Information...............................................................................................................20
5.4.2 General Information..................................................................................................................20
5.4.3 Building Installation Considerations.........................................................................................21
5.4.4 Base Station Antennas...............................................................................................................21
5.4.5 Transmission Lines...................................................................................................................21
5.4.5.1 Minimum Transmission Line Bending Radius........................................................................ 21
5.4.6 Tower Installations....................................................................................................................22
5.5 GROUNDING
5.6 BACKUP
AND LIGHTNING PROTECTION............................................................................22
POWER SOURCES.............................................................................................................23
5.6.1 Uninterruptible Power Supplies................................................................................................23
5.6.2 Gas/Propane Generators............................................................................................................23
5.6.3 Hydrogen Power Systems.........................................................................................................23
5.7 CONNECTING
VOIP DESKTOP REMOTE CONTROLLERS..........................................................23
5.7.1 Setting Up the LAN Port for VoIP Connectivity ......................................................................23
5.7.2 Setting Up VoIP Desktop Remotes...........................................................................................23
5.8 CONNECTING
TONE REMOTE CONTROLLERS ..........................................................................24
5.8.1 Standard Tone Signaling...........................................................................................................24
5.8.2 Dual Function Tone Signaling ..................................................................................................24
5.8.3 Connecting One Tone Remote Controller.................................................................................26
5.8.4 Connecting More-than-One Tone Remote Controllers.............................................................26
5.8.4.1 LINE Input Connector............................................................................................................. 27
5.9 CONNECTING CAN –LINKED REMOTE CONTROLLERS...........................................................27
5.9.1 General Information..................................................................................................................27
3
MM-014714-001, Rev. P3
TABLE OF CONTENTS
Section Page
5.9.2 CAN-Linked Desktop Controller Connections .........................................................................29
5.9.2.1 Collocated Installations............................................................................................................30
5.9.2.2 In-Wall/Plenum CAN Cable Installations................................................................................30
5.9.2.2.1 Cable Requirements and Routing........................................................................................................30
5.9.2.2.2 Installation Materials ..........................................................................................................................31
5.9.2.2.3 Splicing CAN Cables..........................................................................................................................31
5.9.3 Connecting a CAN Bus Extender (Fiber Optic Cable Installations) .........................................33
5.10 CONNECTING DEVICES TO THE EXTERNAL I/O ........................................................................33
5.10.1 Local and Remote Speaker – Jumper Configuration.................................................................33
5.10.2 External I/O Connector (P3) Pinout ..........................................................................................33
6 INITIAL SETUP .........................................................................................................................................36
6.1 CONTROL
6.2 LOCAL
6.3 V
OIP (LAN) SETUP AND ALIGNMENT ...................................................................................................36
6.3.1 Programming the VoIP Remote Board......................................................................................37
6.3.2 Audio Adjustments....................................................................................................................43
6.4 TONE REMOTE (LINE I/O) SETUP AND ALIGNMENT.................................................................44
STATION POWER-UP PROCEDURE............................................................................36
CONTROL STATION SETUP AND ALIGNMENT.............................................................36
6.3.1.1 Programming Parameters.........................................................................................................37
6.3.1.2 Network....................................................................................................................................37
6.3.1.3 Radio........................................................................................................................................37
6.3.1.4 Output.......................................................................................................................................38
6.3.1.5 Action.......................................................................................................................................38
6.3.1.6 Channel ....................................................................................................................................39
6.3.1.7 Remote Configuration..............................................................................................................39
6.3.2.1 Audio........................................................................................................................................43
6.3.2.2 Backup .....................................................................................................................................43
7 OPERATIONAL TESTING.......................................................................................................................45
7.1 SETUP
AND EQUIPMENT TESTING................................................................................................45
7.1.1 REQUIRED TEST EQUIPMENT............................................................................................45
7.2 MAXIMUM
EFFECTIVE RADIATED POWER................................................................................46
7.2.1 Determining Maximum Transmitter Power that Meets ERP Requirement...............................46
7.2.1.1 For OpenSky Mode of Operation.............................................................................................46
7.2.1.2 For P25, EDACS, or Conventional Mode of Operation...........................................................47
7.3 VERIFYING TX RF FORWARD AND REFLECTED POWER.........................................................47
7.4 VERIFYING TX RF FREQUENCY.....................................................................................................48
7.5 VERIFYING
TX MODULATION.......................................................................................................49
7.5.1 Digital Modulation Modes (EDACS, P25, and OpenSky)........................................................49
7.5.2 Analog Modulation Modes........................................................................................................49
7.5.2.1 Desktop Remote Controllers on Systems Using Analog Modes..............................................50
8 COMPLETING THE INSTALLATION ..................................................................................................51
8.1 FINAL
OVER-THE-AIR TESTING ....................................................................................................51
APPENDIX A CONFIGURING VOIP REMOTE CONTROLLERS.................................................. A-1
A.1 IDA MODEL 24-66 VOIP REMOTE CONTROLLER SETUP....................................................... A-3
APPENDIX B INSTALLATION CHECKLIST.................................................................................. B-1
B.1 INSTALLATION DATA SHEET FOR CS-7000 CONTROL STATION ........................................B-3
4
MM-014714-001, Rev. P3
TABLE OF CONTENTS
Section Page
FIGURES
Figure 3-1: CT-013892-001 Local Control Station with Scan Head (Front View).............................12
Figure 3-2: CT-013892-002 Local/Remote Control Station with System Head (Front View)...........12
Figure 5-1: CS-7000 with Remote Control, Front View.....................................................................18
Figure 5-2: CS-7000 Rear Panel (shown with Remote Control Board installed)................................19
Figure 5-3: CS-7000 Fuse Replacement (Rear Panel Views) .............................................................20
Figure 5-4: Tone Remote Control Signaling.......................................................................................25
Figure 5-5: Line Input Configured as an Endpoint and Interfaced to One TRC.................................26
Figure 5-6: Configured as an Endpoint and Interfaced to Multiple Paralleled TRCs.........................26
Figure 5-7: Control Station in the Middle of a Chain and Interfaced to Multiple Paralleled TRCs....27
Figure 5-8: Connecting a CAN-linked Desktop Controller.................................................................28
Figure 5-9: Connecting Two or More CAN-Linked Desktop Controllers..........................................29
Figure 5-10: Connecting a CAN Y-Cable at the Control Station........................................................29
Figure 5-11: Connecting In-Wall/Plenum CAN Cable Connections ..................................................31
Figure 5-12: Dimensions for Stripping 2-Wire (with Shield) CAN Cables........................................32
Figure 5-13: 3-Position Terminal Strip Connections ..........................................................................32
TABLES
Table 3-1: Reference Documents........................................................................................................13
Table 4-1: Catalog, Description, and Part Numbers for the CS-7000 Control Station........................15
Table 4-2: Accessories for the CS-7000 Control Station ....................................................................16
Table 5-1: Minimum Bend Radius Values for RF Transmission Lines..............................................22
Table 5-2: Typical* Tone Functionality for Tone Remote Control Signaling....................................25
Table 5-3: LINE Input Pin-Out (RJ-11 Modular Jack Labeled “LINE”)............................................27
Table 5-4: Interface Board Jumper Configurations..............................................................................33
Table 5-5: Local Control Station - External I/O Port (P3) Wiring Interconnections ..........................34
Table 5-6: Remote Control Station - External I/O Port (P3) Wiring Interconnections.......................35
Table 7-1: Required Test Equipment...................................................................................................45
5
MM-014714-001, Rev. P2
1 REGULATORY AND SAFETY INFORMATION
1.1 MAXIMUM PERMISSIBLE EXPOSURE LIMITS
DO NOT TRANSMIT with this Control Station and antenna when persons are within the MAXIMUM
PERMISSIBLE EXPOSURE (MPE) Radius of the antenna. The MPE Radius is the minimum distance
from the antenna axis that ALL persons should maintain in order to avoid RF exposure higher than the
allowable MPE level set by the FCC.
FAILURE TO OBSERVE THESE LIMITS MAY ALLOW ALL PERSONS
WITHIN THE MPE RADIUS TO EXPERIENCE RF RADIATION
ABSORPTION, WHICH EXCEEDS THE FCC MAXIMUM PERMISSIBLE
EXPOSURE (MPE) LIMIT. IT IS THE RESPONSIBILITY OF THE CONTROL
STATION OPERATOR TO ENSURE THAT THE MAXIMUM PERMISSIBLE
EXPOSURE LIMITS ARE OBSERVED AT ALL TIMES DURING CONTROL
STATION TRANSMISSION. THE CONTROL STATION OPERATOR IS TO
ENSURE THAT NO BYSTANDERS ARE WITHIN THE RADIUS LIMITS.
1.1.1 Determining MPE Radius
THE MAXIMUM PERMISSIBLE EXPOSURE RADIUS is unique for each site and is determined
during site licensing time based on the complete installation environment (i.e., Co-location, antenna type,
transmit power level, etc.). Determination of the MPE distance is the responsibility of the installation
licensee. Calculation of the MPE radius is required as part of the site licensing procedure with the FCC.
1.1.2 Safety Training Information
YOUR M/A-COM CONTROL STATION GENERATES RF
ELECTROMAGNETIC ENERGY DURING TRANSMIT MODE. THIS
CONTROL STATION IS DESIGNED FOR AND CLASSIFIED AS
“OCCUPATIONAL USE ONLY” MEANING IT MUST BE USED ONLY IN
THE COURSE OF EMPLOYMENT BY INDIVIDUALS AWARE OF THE
HAZARDS AND THE WAYS TO MINIMIZE SUCH HAZARDS. THIS
CONTROL STATION IS NOT INTENDED FOR USE BY THE “GENERAL
POPULATION” IN AN UNCONTROLLED ENVIRONMENT. IT IS THE
RESPONSIBILITY OF THE CONTROL STATION OPERATOR TO ENSURE
THAT THE MAXIMUM PERMISSIBLE EXPOSURE LIMITS DETERMINED
IN THE PREVIOUS SECTION ARE OBSERVED AT ALL TIMES DURING
TRANSMISSION. THE CONTROL STATION OPERATOR IS TO ENSURE
THAT NO BYSTANDERS COME WITHIN THE RADIUS OF THE MAXIMUM
PERMISSIBLE EXPOSURE LIMITS.
When licensed by the FCC, this Control Station complies with the FCC RF exposure limits when persons
are beyond the MPE radius of the antenna. In addition, your M/A-COM
complies with the following Standards and Guidelines with regard to RF energy and electromagnetic
energy levels and evaluation of such levels for exposure to humans:
FCC OET Bulletin 65 Edition 97-01 Supplement C, Evaluating Compliance with FCC Guidelines
for Human Exposure to Radio Frequency Electromagnetic Fields.
®
Control Station installation
6
American National Standards Institute (C95.1 – 1992), IEEE Standard for Safety Levels with
Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz.
American National Standards Institute (C95.3 – 1992), IEEE Recommended Practice for the
Measurement of Potentially Hazardous Electromagnetic Fields – RF and Microwave.
TO ENSURE THAT YOUR EXPOSURE TO RF ELECTROMAGNETIC ENERGY
IS WITHIN THE FCC ALLOWABLE LIMITS FOR OCCUPATIONAL USE, DO
NOT OPERATE THE CONTROL STATION IN A MANNER THAT WOULD
CREATE AN MPE DISTANCE IN EXCESS OF THAT ALLOWABLE BY THE
CAUTION
FCC.
This equipment generates or uses radio frequency energy. Any changes or
modifications to this equipment not expressly approved by M/A-COM may cause
CAUTION
harmful interference and could void the user’s authority to operate the equipment.
1.2 SAFETY SYMBOL CONVENTIONS
The following conventions are used throughout this manual to alert the user to general safety precautions
that must be observed during all phases of operation, service, and repair of this product. Failure to comply
with these precautions or with specific warnings elsewhere violates safety standards of design,
manufacture, and intended use of the product. M/A-COM, Inc. assumes no liability for the customer's
failure to comply with these standards.
MM-014714-001, Rev. P3
The WARNING symbol calls attention to a procedure, practice, or the like, which,
if not correctly performed or adhered to, could result in personal injury. Do not
proceed beyond a WARNING symbol until the conditions identified are fully
understood or met.
The CAUTION symbol calls attention to an operating procedure, practice, or the like,
which, if not performed correctly or adhered to, could result in damage to the
equipment or severely degrade equipment performance.
CAUTION
The NOTE symbol calls attention to supplemental information, which may improve
system performance or clarify a process or procedure.
The ESD symbol calls attention to procedures, practices, or the like, which could
expose equipment to the effects of Electro-Static Discharge. Proper precautions must be
taken to prevent ESD when handling circuit boards or modules.
The electrical hazard symbol is a WARNING indicating there may be an electrical
shock hazard present.
7
MM-014714-001, Rev. P2
1.3 IMPORTANT SAFETY INSTRUCTIONS
• Read these instructions.
• Keep these instructions.
• Heed all warnings.
• Follow all instructions.
• Do not use this apparatus near water.
• Clean only with dry cloth.
• Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
• Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding
prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit
into your outlet, consult an electrician for replacement of the obsolete outlet.
• Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
• Only use attachments/accessories specified by the manufacturer.
• Unplug this apparatus during lightning storms or when unused for long periods of time.
• Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
• Warning: The lightning bolt signifies an alert to the user of the presence of un-insulated “dangerous
voltage” within the product’s enclosure that may be of significant magnitude to constitute a risk of
electric shock to persons.
• Warning: The exclamation point alerts the user to the presence of important operation and
maintenance (service) instructions in the literature accompanying the product.
• Outdoor Use Warning: To reduce the risk of Fire or Electric Shock, Do Not Expose This Apparatus
to Rain or Moisture.
• Wet Location Warning: Apparatus shall not be exposed to dripping or splashing and no objects
filled with liquids, such as vases, shall be placed on the apparatus.
8
The CS-7000 contains no user-serviceable parts. Only authorized service personnel should
open the unit. Obey all warning labels. If you do not follow these instructions you may risk
electric shock, and/or damage to the equipment.
2 SPECIFICATIONS1
MODELS
CT-013892-001: Control Station, Local Control, Desktop
CT-013892-002: Control Station, Remote Control, Desktop
CT-013892-003: Control Station, Remote Mount
FRONT PANEL CONTROLS AND FEATURES
Local Control Desktop Station: DC Power LED, Speaker
Remote Control Desktop Station: DC Power LED, Speaker, Station Microphone Jack, Station
Remote Mount Station: DC Power LED
REAR PANEL CONNECTORS AND FEATURES
Local and Remote Models
AC Power Input: IEC-302, Unified Power Connector/Fuse/ON-OFF Switch
Antenna Connector: Type-N, 50 Ohm, Female
MM-014714-001, Rev. P3
Volume Control, VU Meter, Intercom Switch, Remote Switch
External I/O (P3): DB-25F, I/O, Small Signal – Direct Function
Serial A (P2): USB, 2.0 Type B, 12 Mbps, Radio Programming Port
Serial B (P6): DB-9F, RS-232C (DCE), Serial Interface, Full Duplex, Hardware
Flow Control, ASYNC and SLIP at 19.2kbps
Remote Models Only
CAN Link (J15): 2-Wire Differential, 120 ohms, V2.0B 500kbps
LINE Input (J18): RJ-11 Tone Remote, 600 ohm,
Line-Input: -30 to 0 dBm (-20 to +11 dBm Securitone level).
Line-Output: 0 dBm.
Computer (J1): RJ-45, 10/100BaseT, Ethernet, to Local PC
LAN (J6): RJ-45, 10/100BaseT, Network, to VoIP Remote Controllers
DIMENSIONS (H x W x D):
Desktop: 3.5 x 17 x 13.1 inches (8.9 x 43.2 x 33.3 cm) excluding 1 in.
(2.54 cm) rubber feet
Rack Mount: 3.5 x 17 x 13.1 inches (8.9 x 43.2 x 33.3 cm)
WEIGHT
w/o Transceiver: 18 lbs (8.2 kg)
w/Transceiver: 24 lbs (11 kg)
1
Specifications listed herein are intended primarily for the use of the service technician. See the appropriate Specifications
Sheet for complete specifications.
9
MM-014714-001, Rev. P2
AC INPUT
Maximum: 120 VAC (240VAC), 4.0 Amps (2 Amps), 400 Watts, 50/60 Hz
Transmit (typical): 120 VAC (240VAC), 2.5 Amps (1.25 Amps), 300 Watts, 50/60 Hz
Receive (typical): 120 VAC (240VAC), 1.2 Amps (0.6 Amps), 100 Watts, 50/60 Hz
ENVIRONMENTAL
Operating Temperature: -30 to +40ºC @ 50% duty cycle
Storage Temperature: -40 to +70ºC
Standards: MIL-STD-810F
Test Methods: Low Pressure 500.4/2
-30 to +60ºC @ 20% duty cycle
High Temperature 501.4/1,2, Category A1
Low Temperature 502.4/1,2 Category C1
Temperature Shock 503.4/1, Categories A1 and C1
Vibration, Non-Operational 514.5/1 Category 2
Shock, Transit Drop 516.5/4
Shock, Bench Handling 516.5/6
Humidity 507.4/2
SAE-J551/15 ESD (Functional) Human Body Model
DUTY CYCLE
Receiver: 100% (per EIA-603)
Transmitter: 20 % (per EIA-603)
SPEAKER
Impedance: 12 ohms
Rated Power: 3 W RMS
Distortion: 5% at rated power from 300-3000 Hz
Buzzes/Rattles: None
Acoustic Output:: 95 dB SPL @ 3 W @ 12 inches @ 1 KHz
Acoustic Response: ± 5 dB from 300-3000 Hz
REMOTE CONTROL MODES (Optional)
Tone Remote Control: 2 or 4-wire Tone Remote Control
Modes: EDACS, P25, OpenSky, and Conventional.
Voice over IP: VoIP Audio with PTT Control.
Modes: EDACS, P25, OpenSky, and Conventional.
Controller Area Network: CAN Interface, Supports up to 4 CAN-Linked peripherals
Modes: OpenSky and Conventional.
10
MM-014714-001, Rev. P3
TRANSCEIVER Specifications determined by the Mobile Radio’s Specifications.
Refer to the applicable M5300/M7300 Mobile Radio Maintenance
Manual.
REGULATORY FCC Part-15 Class B Com pliant
FCC Part 90 Compliant (refer to mobile radio manual)
Industry Canada RSS-119 (refer to mobile radio manual)
EN60950 Compliant
CSA22.2 Compliant
11
MM-014714-001, Rev. P2
3 INTRODUCTION
The M/A-COM CS-7000 Control Station provides the latest in digital radio technology via the M/ACOM M5300 or M7300 mobile radio installed into the Control Station. The station may be equipped to
support one or more of the following operating modes:
• OpenSky® digital operation.
• Enhanced Digital Access Communications System (EDACS®) or ProVoice™ trunked modes.
• APCO Project 25 Phase I compliant Common Air Interface (P25 CAI) trunked radio networking.
• Conventional analog mode.
The CS-7000 Control Station is typically used for voice and data dispatch communications via optional
remotely-connected Desktop Controllers. Remote Desktop Controllers may be connected via any of the
following remote control formats:
• Controller Area Network (CAN) link connection.
• Tone controlled line input.
• LAN-based Voice over Internet Protocol (VoIP) connection.
CAN links are generally limited to 250 feet end-to-end line length, but may utilize an optional fiber-opticbased CAN Bus Extender for increased separation between the CS-7000 and CAN-linked Desktop
Controllers. Tone Remote Controllers connect via 2-wire or 4-wire line audio connections. VoIP
requires connectivity to a Wide Area Network (WAN) or Local Area Network (LAN).
12
Figure 3-1: CT-013892-001 Local Control Station with Scan Head (Front View)
Figure 3-2: CT-013892-002 Local/Remote Control Station with System Head (Front View)
3.1 VOICE OPERATION
The voice path operates like a traditional dispatch radio, with a microphone to transmit (push-to-talk) and
a speaker to receive. In OpenSky Trunked Protocol and P25 modes, all voice communications are
transmitted in a digital mode. Systems operating in EDACS mode may employ both analog and digital
voice modes, and a data mode.
3.2 OPTIONAL REMOTE CONTROL BOARD
The CS-7000 Control Station may be equipped with the optional Remote Control Board. The Remote
Control Board provides the ability to remotely control the station features such as PTT (transmit), group
and/or channel control, and intercom.
3.2.1 Intercom Operation
Control Stations equipped with the optional Remote Control Board are also equipped with an intercom
function. The intercom function allows voice communications between the Control Station’s operator
and operators at Desktop Controllers connected via the CAN link, VoIP link, or Tone Remote Controllers
connected to the line connector. Even when intercom is activated, incoming network radio calls are still
routed to the speaker in the Desktop Controllers in receive mode (not keyed). In other words, radio calls
are not muted when the Desktop Controller’s intercom function is active (with the exception of the remote
that is keyed and making an intercom transmission).
MM-014714-001, Rev. P3
3.3 RELATED DOCUMENTATION
The following documents contain additional information relative to the CS-7000 Control Station. These
documents may be helpful during the installation and maintenance of this equipment.
Table 3-1: Reference Documents
DOCUMENTATION MANUAL NUMBER
CS-7000 Control Station Operator’s Manual MM-014713-001
CS-7000 Control Station Maintenance Manual MM-014715-001
M5300 Transceiver Operator’s Manual MM-012125-001
M5300 Transceiver Quick Guide when using OpenSky Systems MM-012997-001
M5300 Transceiver Quick Guide when using P25, EDACS, or
Conventional Systems
M7300 Transceiver Operator’s Manual MM-014718-001
M7300 Transceiver Quick Guide when using OpenSky Systems MM-014368-001
M7300 Transceiver Quick Guide when using P25, EDACS, or
Conventional Systems
MM-013232-001
MM-014369-001
M5300/M7300 Software Release Notes
Site Grounding and Lightning Protection Guidelines AE/LZT 123 4618/1
MS-014467-001
13
MM-014714-001, Rev. P2
DOCUMENTATION MANUAL NUMBER
Tower Requirements and General Specifications LBI-39185
Antenna Specifications LBI-38983
CAN Bus Extender MM-009088-001
3.4 TECHNICAL ASSISTANCE
Should the CS-7000 Control Station require repair, or if you have questions or concerns about the
installation of this equipment, contact M/A-COM’s Technical Assistance Center (TAC) using the
following telephone numbers or email address:
• U.S. and Canada: 1-800-528-7711 (toll free)
• International: 1-434-385-2400
• Fax: 1-434-455-6712
• Email: tac@tycoelectronics.com
3.5 CUSTOMER RESOURCE CENTER
Replacement parts can be ordered through M/A-COM’s Customer Resource Center. To order replacement
parts through the Customer Resource Center, call, fax or email our ordering system:
North America:
• Phone Number: 1-800-368-3277 (toll free)
• Fax Number: 1-800-833-7592 (toll free)
• E-mail: customerfocus@tycoelectronics.com
International:
• Asia Pacific: 1-434-455-9223
• Latin America & Middle-East: 1-434-455-9229
• Europe: 1-434-455-9219
• Fax Number: 1-434-455-6685
• E-mail: customerfocus@tycoelectronics.com
14
MM-014714-001, Rev. P3
4 UNPACKING AND CHECKING EQUIPMENT
4.1 MATERIALS
The CS-7000 Control Station includes an AC Power Cord to connect it to standard AC power (120 VAC,
60 Hz). No installation kit is available, as every installation is custom. The CS-7000 is generally used in
conjunction with a Desktop Controller, both of which have accessories that can be installed. Table 4-1
4.2 MATERIAL INSPECTION
lists equipment top-level part numbers, and Table 4-2 lists available accessories.
The CS-7000 must not be powered up unless an antenna is installed and
connected. An antenna and its cabling must be purchased separately. Antennas and
coaxial cables are typically customized to the installation site. Have site surveys
performed to identify an appropriate antenna and antenna feed line requirements.
After removal from the carton, examine the components and installation items for
broken, damaged, loose or missing parts. If any are noted, contact M/A-COM’s
Customer Resource Center immediately to discuss and arrange for the return of the
equipment to M/A-COM for replacement. Refer to Section 3.5 on page 14 for the
CAUTION
Customer Resource Center contact information. Any unauthorized attempts to repair
or modify this equipment will void the warranty and could create a safety hazard.
Upon removing items from the carton and verifying all equipment is accounted for, proceed with the
installation.
Mounting of the CS-7000 and/or antenna in ways other than those described can
adversely affect performance, violate FCC rules on RF exposure, and even
damage the unit, posing a potential safety hazard.
Table 4-1: Catalog, Description, and Part Numbers for the CS-7000 Control Station
DESCRIPTION PART NUMBER
Control Station, Desktop Configuration, Local Control CT-013892-001
Control Station, Desktop Configuration, Remote Control CT-013892-002
Control Station, Remote Configuration, Remote Control CT-013892-003
15
MM-014714-001, Rev. P2
PART NUMBER DESCRIPTION
MC-014121-001 Desktop Microphone
MAMROS0093 Antenna, 800 MHz 6-element Yagi with 8 dBd Gain
AN-025137-004 Antenna, 700 MHz 6-element Yagi with 7 dBd Gain
MAMROS0094 Antenna Mounting Kit, Universal Mount for Yagi Antennas
MAMROS0095 Cable, Coax: Antenna Jumper Kit
DSXL-MA-BF
CD-014027-001 CAN Terminator
CA-009562-0R6 Cable, CAN; 0.6 feet, Black, Right-Angle-to-Straight Connectors
CA-009562-006 Cable, CAN; 6 feet, Black, Right-Angle-to-Straight Connectors
CA-009562-030 Cable, CAN; 30 feet, Black, Right-Angle-to-Straight Connectors
Table 4-2: Accessories for the CS-7000 Control Station
Lightning Protection Device with DC Blocking (PolyPhaser DSXL-MABF), 700 to 2700 MHz, N-male to N-female connectors, elongated
female connector for PolyPhaser BFN or BFD flange mount adapters.
CA-009562-090 Cable, CAN; 90 feet, Black, Right-Angle-to-Straight Connectors
CA-009562-250 Cable, CAN; 250 feet, Black, Right-Angle-to-Straight Connectors
CA-011344 CAN Y-Cable, Black, Right-Angle-to-Two Straight Connectors
MAA7-NSU5C
TQS3385 Rev. B (min)
TQS3389 Rev. A (min)
Kit, CAN Bus Extender (Includes CAN Bus Extender MD-008577 and
AC Wall Power Supply.) [2 required per optical CAN link.]
Radio Personality Manager (Programming Software for P25, EDACS,
OpenSky)
Radio Personality Manager (Programming Software for Analog
Conventional and P25 Conventional)
16
5 INSTALLATION
M/A-COM recommends the buyer use only a M/A-COM authorized
representative to install and service this product. The warranties provided to the
buyer under the terms of sale shall be null and void if this product is installed or
CAUTION
5.1 REQUIRED TOOLS AND EQUIPMENT
5.1.1 Tools and Shop Supplies Required to Install the CS-7000
The following is a list of tools required to complete a standard installation:
• Phillips screwdrivers, sizes #1 and #2;
serviced improperly, and M/A-COM shall have no further obligation to the buyer for
any damage caused to the product or to any person or personal property.
Prior to installation, ensure that the CS-7000 has been configured for customer usage
such as channels and personality.
MM-014714-001, Rev. P3
• Flat head screwdrivers, sizes #1 and #2;
• Slip-jaw pliers;
• 3/8” Nut driver;
• Various fasteners; as required.
Special tools needed to construct and/or install optional cables and accessories are listed in the installation
and configuration sections for the option or accessory.
5.1.2 Equipment Required for CS-7000 Configuration
The following is a list of additional equipment needed to configure the CS-7000:
• Personal Computer (PC) with an available USB communication port and running Microsoft
®
Windows
XP or Windows Server 2003. OpenSky programming requires a terminal application
software program such as Windows HyperTerminal, and P25, EDACS, and Conventional requires the
programming software listed in Table 4-2 on page 16;
• Standard USB 2.0B computer cable;
• See Table 7-1 on page 45 for a list of test equipment required to perform antenna tests procedures.
5.2 PLANNING THE CS-7000 INSTALLATION
Plan the mounting locations of all components (CS-7000, antenna, and cables) and determine the routes
for all wiring and cables. Consider also the connection of desktop remotes for planning purposes. Follow
all manufacturer requirements and guidelines for the location of components.
®
For installations with CAN-linked Desktop Controllers which require connection
through the CAN (Controller Area Network) digital interface, pay particular attention
to the routing of CAN cable in the facility. It may be necessary to use plenum-rated
cable for in-building installations. Refer to Section 5.9 that begins on page 27 and/or
consult with TAC to identify the proper cabling.
17
MM-014714-001, Rev. P2
All cables should be installed with a service loop at each end. During the installation,
do NOT bend any cable at a severe angle near a connector. When the installation is
complete, verify no cable is under any tension. Failure to do so may lead to damaged
CAUTION
cables, causing intermittent operation, or complete equipment failure.
Optimal performance is based upon proper mounting techniques. An improperly
installed unit may experience degradation in the quality of communication with the
CAUTION
OpenSky network.
5.3 CS-7000 INSTALLATION
Determine the customer’s preferences, if any, for location of components. Comply with these preferences
insofar as they are consistent with safety, manufacturer specifications, and generally accepted
professional practices.
5.3.1 Desktop Installations
The CS-7000 can be placed upon a desktop, tabletop, or another flat horizontal surface with an adequate
size and weight rating. The unit’s dimensions are 3.5 x 17 x 13.1 inches (8.9 x 43.2 x 33.3 cm) and it
weighs approximately 24 lbs. (11 kg.).
5.3.2 Rack-Mount Installation
The CS-7000 Remote Configuration Station model CT-013892-003 is designed for mounting within a
19-inch rack-mount cabinet. Its height is two rack-units (3.5 inches). Mounting brackets are attached to
the side corners near the front and rear panel of the CS-7000 at the factory.
Figure 5-1: CS-7000 with Remote Control, Front View
18
MM-014714-001, Rev. P3
Figure 5-2: CS-7000 Rear Panel (shown with Remote Control Board installed)
Never place any other equipment directly on top of the CS-7000. The case is not
designed to handle the weight of other equipment.
CAUTION
The CS-7000 must be kept away from sources of heat. Adequate ventilation must
be provided to the air inlet at the rear of the unit where the fan is located and to
the ventilation holes on the rear-sides of the unit.
5.3.3 AC Power Connection
The CS-7000 only supports an AC power connection. Follow these general guidelines:
• Ensure familiarity with AC power input connection, including maintenance of the fuse; and,
• Make certain that cable routing will not damage or interfere with any existing wiring at the
installation location.
In order to accommodate both U.S. and other standards, the CS-7000 can be used at voltages in the range
of 110 – 120 VAC (50/60 Hz) and 220 – 240 VAC (50/60 Hz). The power cord for U.S. applications
(110 – 120 VAC) is included with the CS-7000 when it ships from the factory. For other applications, the
appropriate power cord must be purchased separately. The receptacle at the back of the CS-7000 is an
IEC-320 C14-type connector for accepting a cord with an IEC-320 C13-type plug.
5.3.4 AC Fuse Replacement
In the event that a fuse blows in the CS-7000, disconnect AC power from the unit by unplugging the cord
from the AC power source or by unplugging the cord from the IEC-320-type AC power connector on the
CS-7000’s rear panel, and follow this replacement procedure:
1. As shown in Figure 5-3, slip the tip of a small flat-blade screwdriver into the pry slot at the top of the
AC Power Module and open the fuse assembly door.
2. Remove the fuse holder and replace the blown fuse with a new 4-amp, 250-volt fuse.
3. Re-insert and reseat the fuse assembly until the panel snaps back into place.
4. Reconnect AC power to the unit.
19
MM-014714-001, Rev. P2
Figure 5-3: CS-7000 Fuse Replacement (Rear Panel Views)
5.4 ANTENNA INSTALLATION
Antenna installations vary greatly depending on the type of antenna mounting structure, height, and the
surrounding environment. Professional antenna installation services are highly recommended when
installing and maintaining communications antenna systems. This manual makes no attempt to provide
step-by-step instructions for installing the antenna and supporting structure. Rather, general
recommendations and considerations are provided. Further, where installation instructions provided by
antenna and other related antenna equipment manufacturers differ from this manual, the manufacturer’s
instructions are to be followed at all times. When in doubt, always contact the equipment manufacturer or
M/A-COM Technical Assistance Center for further assistance. Follow all national an d local building
code requirements when installing antenna systems.
5.4.1 RF Safety Information
The antenna must be installed by a qualified antenna professional. Improper
installation of the antenna may lead to poor radio performance, and harmful
exposure to RF electromagnetic energy.
The CS-7000 antenna installation must comply with the FCC RF exposure limits as discussed in Section
1.1. Installation of the antenna for the CS-7000 is to be performed so that no person is within the distance
of maximum permissible exposure limits specified in the FCC regulations. The CS-7000 must be disabled
before antenna maintenance is performed.
5.4.2 General Information
M/A-COM has available several manuals that provide useful information during the installation process.
General antenna installation specifications may be found in M/A-COM’s Antenna Systems Manual,
LBI-38983. Tower Requirements and General Specifications may be found in the Specifications,
Guidelines, and Practices Manual, LBI-39185. And, site grounding must conform to the requirements
found in the Site Grounding and Lightning Protection Guidelines Manual, AE/LZT 123 4618/1.
Failure to follow these instructions will void the product warranty and may expose the end user and others
to excessive Radio Frequency hazards. All antennas should be installed outdoors; and where practical, at
distances from personnel well beyond the minimum allowable distance.
20
Loading...