HARRIS TR0001-E Users Manual
CLIENT: COM-NET ERICSSON CRITICAL RADIO SYSTEMS, INC.
CLIENT REFERENCE NUMBER: QRTL00-230
WORK ORDER NUMBER: 2000043
EUT: EDACS-300P
FCC ID: OWDTR0001-E
APPENDIX H:
PRELIMINARY USER’S MANUAL
Page 108 of 131
EN/LZT 123 5652/1 R1A
Operator’s Manual
EDACS 300P
System/Scan Portable
Radio
Table of Contents
User Interface.............................................................................. 3
Basic Operation.......................................................................... 6
Trunked Mode Operation............................................................ 8
Conventional Operation ........................................................... 13
Programmable Alert Tones ...................................................... 14
Error Messages......................................................................... 15
Changing the Battery Pack....................................................... 16
Operating Rules and Regulations............................................ 18
Intrinsically Safe Usage............................................................ 19
Operating Tips.......................................................................... 20
NOTICE!
The software contained in this device is copyrighted by Com-Net
Ericsson. Unpublished rights are reserved under the copyright laws of
the United States.
This manual is published by Com-Net Ericsson, without any warranty. Improvements
and changes to this manual necessitated by typographical errors, inaccuracies of current
information, or improvements to programs and/or equipment, may be made by Com-Net
Ericsson, at any time and without notice. Such changes will be incorporated into new
editions of this manual. No part of this manual may be reproduced or transmitted in any
form or by any means, electronic or mechanical, including photocopying and recording,
for any purpose, without the express written permission of Com-Net Ericsson.
Copyright © 2000 Com-Net Ericsson. All rights reserved.
2
User Interface
EMERGENCY/
HOME BUTTON
POWER ON/OFF
This manual describes the basic functions and operation of
the EDACS 300P System/Scan portable radio. For more
detailed information about the features and operation, refer
to the appropriate EDACS 300P Maintenance Manual or
contact your System Administrator.
ANTENNA
VOLUME KNOB
Figure 1. EDACS 300P Top View
3
CLEAR/
LOCK
SCAN
SPECIAL
SELECT
PTT
ON/OFF/
VOLUME
BUTTON
ANTENNA
CHANNEL
4
SYSTEM/
GROUP/
CALLS
STORE
Figure 2. EDACS 300P System Model
DISPLAY
MONITOR/
SHIFT
ON/OFF
ON/OFF
RECALL
CLEAR/
SCAN
SPECIAL
SELECT
PTT
ON/OFF/
VOLUME
BUTTON
ANTENNA
SYSTEM/
GROUP/
CHANNEL
CALLS
Figure 3. EDACS 300P Scan Model
DISPLAY
MONITOR/
SHIFT
ON/OFF
5
Basic Operation
Locking/Unlocking Keypad (System Model)
1. Press and hold the C/M key.
2. Press and release the LOCK key. Then release the
C/M key.
Selecting System
1. Press and release the C/M key. Then use the and
keys to select the desired system.
2. The SYS field displays the current System selected.
Selecting Group/Channel
1. Press the and keys to access the desired
group/channel.
Enabling/Disabling Scan
1. Press and release the SCN key to toggle Scan
ON/OFF. “SCN” is displayed when Scan is enabled.
Modifying Scan List
1. Select desired Group/Channel to be added/deleted. If
Group/Channel is currently in Scan list, “S” is
displayed.
2. Press and hold the C/M key.
3. Press and release the SCN key. Then release the
C/M key.
6
4. If selected Group/Channel was not in Scan list, it will
be added. If selected Group/Channel was in Scan list,
it will be deleted.
Home/Emergency Key Definition
Pressing the red Home/Emergency button will perform one
of the four operations below, depending upon how the
radio was programmed.
1. Radio will switch to the programmed home System
and/or Group, and send an emergency transmission.
2. Radio will send an emergency transmission on the
current System/Group.
3. Radio will switch to the home System and/or Group.
4. Button is not active.
Declaring Emergency
1. Press and hold the red Emergency/Home button (the
length of time is programmable; check with the System
Administrator).
2. If programmed, an “E” is displayed in the SYS field
and/or an alert tone sounds.
3. Press PTT button to transmit your message.
4. Release PTT button when transmission is complete.
7
Loading...