Harmonic MediaGrid ContentDirector 1000F, MediaGrid High Performance ContentDirector 2000C Quick Reference Manual

Harmonic MediaGrid ContentDirector 1000F

and High Performance ContentDirector 2000C

Front Panel Components

MediaGrid

ContentDirector

Quick Reference Guide

Power indicator/Wink

1

7

1 System label pull-out tab
2 Optical drive

ContentDirector 1000F:

7 Hard drive 0
8 Hard drive 1

Rear Panel Components

1

Air vents

2

8

3 LCD panel
4 LCD menu buttons

High Performance ContentDirector 2000C:

7 Solid-state drive 0
8 Solid-state drive 1

2

3

4

3

>

<

5 USB connectors (2)
6 Control panel

5

4

Status LEDs

6

5

6

1 Power suppy 1
2 Release lever
3 Power supply 2
4 Ethernet port 3
5 Ethernet port 2

Harmonic Technical Support: [phone] (Americas), [phone] (Asia Pacific), + 44 1252 555 450 (EMEA),

[phone] (Russia, CIS), [phone] (Japan), [phone] (China, mainland)

6 Ethernet port 0
7 Ethernet port 1
8 VGA port
9 RJ-45 serial port
(serial cable not included)

7

8 10

9

11

10 USB ports (3)
11 Diagnostic LEDS (for Service only)
12 System Status LED
13 System ID LED
14 BMC (currently unused)

121314

006-0188-001 Rev. A

Front Panel LEDs

7

812

345

6

Front Panel Status Indicators

Public NIC

Private NIC

SSD 0

SSD 1

Public and Private NIC Indicators

White

Yellow

Magenta

Both connections are good

Public: NIC 0 connection failure
Private: NIC 2 connection failure

Public: NIC 1 connection failure
Private: NIC 3 connection failure

Red

Both connections have failed

SSD Indicators

White

Yellow

Red

Drive online

Drive replacement
warning

Drive failure

Control Panel Indicators

For more information regarding Control Panel LED indicators, refer to the Harmonic MediaGrid Installation and Configuration Guide.

Drive Indicators

Drive-status Indicator

Drive-activity Indicator

Rear Panel LEDs

1 System ID button with integrated LED

Off Normal system operation
Blue [Blink] System is being winked

2 NMI button (recessed)

3 NIC 0 Activity LED
4 NIC 1 Activity LED

[Solid] A network link is detected
[Blink] Network activity is occurring

Drive-status Indicator Pattern (RAID Only)

[Blink] RAID rebuild in progress (1 Hz), Identify (2 Hz)
[Solid on] Hard drive fault has occurred
[Off] No access and no fault

Drive-activity Indicator Pattern

[Stays off] Power on with no drive activity, drive spun down, or drive spinning up
[Blinks on when processing a command] Power on with drive activity

5 System cold reset button (recessed)

6 System status LED

Green [Solid] Operating (in SO state) and healthy
Green [Blink] Operating in degraded or redundant state
Amber [Blink] Non-fatal alarm
Amber [Solid] Fatal alarm

7 Drive activity LED

8 Power/Sleep button with integrated LED
Green System power is on.

(amber)

(green)

System ID and System Status Indicators

These LEDs show the same states that the corresponding LEDs on the front Control Panel show.

NIC Indicators

Link indicator

Power Supply Status Indicator

Harmonic Technical Support: [phone] (Americas), [phone] (Asia Pacific), + 44 1252 555 450 (EMEA),

Activity indicator

NIC Indicator Codes

[Link and activity indicators are off] The NIC is not connected to the network.
[Link indicator is green] The NIC is connected to a valid link partner on the network.
[Link indicator is amber] The NIC is connected to a valid network link at 10/100 Mbps.
[Activity indicator is amber blinking] Network data is being sent or received.

Off AC power is not connected.
Green [Solid] Indicates that a valid AC source is connected to the power supply, and that

the power supply is operational.
Green [1 Hz Blink] AC is present, but the power switch on the front panel is off or in a
cold redundant state due to low system power load.

Green [2 Hz Blink] Power supply FW updating.
Amber [Blink] Power supply is operational, but experiencing a warning event.
Amber [Solid] AC power is lost or a power supply is shut down.

006-0188-001 Rev. A

[phone] (Russia, CIS), [phone] (Japan), [phone] (China, mainland)