Harmonic MediaDirector 2202 Quick Reference Manual

MediaDirector™ 2202 Quick Reference Guide

Rear Panel Components

3

2

1

eth 5 eth 4 eth 3 eth 2

1 Gb Quad Port Ethernet Expansion Card

1. Power Button

2. Alt/Boot Button

3. Reset Button

4. LTC IN Connector

* Use these ports to connect to MediaPorts only; DO NOT use these ports for any other purpose, including plugging directly into a network.

4

012345678

LTC IN

11

OR

10 Gb Dual P ort Optical Fibre Expansion Card

5. MediaPort Ethernet Array*

6. Fibre Channel Loop Status LEDs

7. Fibre Channel Loop 0-7

8. Optional Expansion Card Slot

10

ixeth 1 ixeth 0 ixeth 1 ixeth 0

5

12

10

9

11

13

ETH 0 ETH 1

14
15

9

OR

6

0 321

0 1 2 3

4 5 6 7

4

10 Gb Dual P ort Ethernet Expansion Card

9. Ethernet Ports

10. For service use only

11. Redundant Power Supplies

7

5

7

6

8

MediaPort Ethernet Array

Link

Link

Amber = 100 Mbps

Activity

Activity

Green (blink) = Normal

1 Gb Quad Port Ethernet Card Status LEDs

Green = 1 Gbps

Off = Inactive or 10 Mbps

Ethernet Port Status LEDs

Link

Activity

10 Gb Dual Port Ethernet Status LEDs

Link Activity

Amber = 1 Gbps

Yellow (blink) = Normal

Green = 100 Mbps

Off = Inactive or 10 Mbps

Link

Link

Amber = 1 Gbps

Activity

Activity

Green (blink) = Normal

Green = 100 Mbps

Off = Inactive

Green, solid = On
Green, blinking = Activity on port

(Look slightly upwards to view the LED)

10 Gb Dual Port
(Optical)

10 Gb Dual Port

Harmonic Technical Support: [phone] (Americas), [phone] (Asia Pacific), + 44 1252 555 450 (EMEA),

[phone] (Russia, CIS), [phone] (Japan), [phone] (China, mainland)

28-0295 Rev. G

4 Gbps LED

Hardware State

Notes

Off

Power off

Card has no power

On, green

Power on

initialization)

All LEDs are on

Flash, green

Power on

initialization)

All LEDs flash at the same

Flash in sequence

Firmware fault

LEDs flash yellow

yellow

On/flash, green

4 Gbps link UP/ACT

On for link UP. If not I/O

second

Limited Use LEDs

Hardware State

Notes

enabled

Fibre Channel Loops Status LEDs

Fibre Channel Loop Status LEDs

2 30 1

or

4 5 6 7

Limited Use
(Normal = black)

4 Gbps
(Green)

Limited Use
(Normal = black)

Front Panel Status LEDs

Limited Use and 4 Gbps
LEDs for loop flash green

(before firmware

(after firmware

Missing Cable in SFP or
FC loop is unused and

continuously

time

green, amber, back to

activity, the green LED
flashes several times per

None

1. File System

Black File system installation not complete

Green File system in process of coming up

Dark Blue (Solid) File system started, read only
(Blink) File system present, halted

Light Blue (Solid) File system started, read-write
(Blink) File system present, unable to start

2. RAID
Black RAID system initialization not complete
Green (Solid) Rebuild(s) in process

(Blink) One or more RAID sets unprotected

Dark Blue (Blink) RAID sets present, no file system running

Light Blue (Solid) All RAID sets protected
(Blink) File system not viable to start

Unused

1

2

3. Built-in Ethernet
Black No ports connected

Dark Blue Hardware or software fault

Light Blue (Solid) At least one port linked at 1 Gb
(Blink) At least one port linked at less than 1 Gb

4. Expansion Ethernet

Black No ports connected

Dark Blue Hardware or software fault

Light Blue (Solid) No expansion card present, or at least
one Ethernet port linked and all ports at maximum
speed (10 Gb or 1 Gb)
(Blink) At least one port linked at less than
maximum speed (<10 Gb or <1 Gb)

5. Fibre Channel

Black No disks detected

Dark Blue (Solid) Disk present, file system running, EFS
(Blink) Fibre Channel initialization in progress

Light Blue (Solid) Disk present, file system running, no EFS
(Blink) Fibre channel initialization complete,
file system in progress

Green (Solid) Fibre channel driver shut down
(Blink) Internal failure detected

3

4

5

Harmonic Technical Support: [phone] (Americas), [phone] (Asia Pacific), + 44 1252 555 450 (EMEA),

[phone] (Russia, CIS), [phone] (Japan), [phone] (China, mainland)

28-0295 Rev. G