Harmonic MediaCenter 2200B, MediaDirector 2252B Quick Reference Manual

MediaCenter™ 2200B Quick Reference Guide

Front panel components

1

MediaCenter

2

3

4

Drive numbering and file system configurations

2

2

1

0

1

6

5

4

3

6

8

9 12

8

7

Rear panel components

2

1

4

3

1. Air vents

2. Power indicator

5

113

11

10

10

9

3. Status LEDs

4. Power button

# Drives RAID set

12 SAS 32 TB

12 SAS 16 TB

2 x (4+2)

2 x (4+2)

Capacity per drive Storage capacity

5. Reset button

4 TB

2 TB

5

6

1. Boot drive

2. Power button/LED

3. LTC In connector

4. 1 Gb Eth ports (1, 2 from left to right.
For system management)

* Use these ports to connect to Spectrum I/O (for example, MediaPorts) only; DO NOT use these ports for any other purpose.

Harmonic Technical Support: [phone] (Americas), [phone] (Asia Pacific), + 44 1252 555 450 (EMEA),

[phone] (Russia, CIS), [phone] (Japan), [phone] (China, mainland)

7

5. MediaPort Ethernet array*

6. Redundant, hot-swappable
power supplies (0, 1 from left to right)

7. 10 Gb Ethernet ports (for file transfers)

8. VGA port (for Service only)

98 10

11

9. RS-232 serial (for Service only)

10. USB ports (for Service only)

11. BMC (for Service only)

006-0187-001 Rev. A

Front panel status LEDs

File system indicator

No root file system

Off

File system

RAID

Built-in

Ethernet

Expansion

Ethernet

Green

Dark blue

Light blue

Dark blue

Light blue

File system coming up

(Solid) Root file system started, read-only
(Blink) Root file system present, halted

(Solid) Root file system started, read-write
(Blink) Root file system present, unable to start

Built-in Ethernet

No ports connected

Off

(Solid) At least one connected port not assigned
an IP address
(Blink) Hardware or software fault

(Solid) At least one port linked at 1 Gb or more
(Blink) At least one port linked at less than 1 Gb

MediaPort Ethernet array

Link

Link

Amber = 100 Mbps

Green = 1 Gbps

Off = Inactive or 10 Mbps

Activity

Activity

Green (blink) = Normal

Raid set indicator

Off

No RAID sets or root file system unavailable

Yellow

Dark blue

Light blue

Dark blue

Light blue

(Solid) Rebuild(s) in proces
(Blink) One or more RAID sets unprotected

(Blink) RAID sets present, no root file system

(Solid) All RAID sets protected (non- compromised)
(Blink) Root file system not viable to start

Expansion Ethernet

Off

No ports connected

Hardware or software fault

(Solid) No expansion card present, or at least one Ethernet
port linked and all ports at maximum speed (10 Gb or 1 Gb)
(Blink) At least one port linked at maximum speed (<10 Gb
or <1 Gb)

1 Gb Ethernet port status LEDs (for EFS*)

Link

Link

Amber = 1 Gbps

Green = 100 Mbps

*For EFS private network interface.

Activity

Activity

Green (blink) = Normal

1 Gb Ethernet port status LEDs (for system management)

The Ethernet card for connecting to system management may vary. Your system may use one of the following.

Link/Activity
100
1000

SpeedLink/Activity

Link/Activity = On with any link, blinks on activity
100 = On with 100 Mbps link
1000 = On with 1 Gbps link

Green = Link, 1 Gbps

Off = no link

Amber = 1 Gbps

Green = 100 Mbps

Off = Inactive or 10 Mbps

Power supply status LED 10 Gb Ethernet port status LEDs

Off = AC power is not connected.

Green (solid) = A valid AC source is connected to the power supply, and the

power supply is operational.

Green (1 Hz blink) = AC is present, but the power switch on the front panel is off
or in a cold redundant state due to low system power load.

Green (2 Hz blink) = Power supply firmware updating.

Amber (blink) = Power supply is operational, but experiencing a warning event.

Amber (solid) = AC power is lost or a power supply is shut down.

Link/Activity

Link/Activity Speed

Green (blink) = activity
Green (solid) = link
Off = no link

Green = 10 Gbps
Amber = 1 Gbps
Off = 100 Mbps

Speed

Harmonic Technical Support: [phone] (Americas), [phone] (Asia Pacific), + 44 1252 555 450 (EMEA),

[phone] (Russia, CIS), [phone] (Japan), [phone] (China, mainland)

006-0190-001 Rev A