Harman Becker Automotive Systems P102 Users Manual

Excerpt from:

User Manual MMI3G with Headphone P102

ENGLISH – DRAFT/correction copy/for internal use

statements FCC part 15.19 and 15.21:

"This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation."
"Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment."

This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Headphones

Switch wireless headphones on/off (Applies only to vehicles with Rear Seat Entertainment)

Figure 105 wireless headphones on and off
Wireless headphones on

► To switch on the wireless headset, press the power button (1) Figure 105 on the right earpiece (R)
for about 3 seconds until the diode (2) starts to flash. The connection between Rear Seat
Entertainment and the wireless headset is established after short time. When the connection is
established, the diode (2) flashes slowly.
Wireless headphones off
► To turn off the wireless headset, press the power button (1) until the diode (2) is off.

CAUTION

- Use the headphones as a driver for security reasons only when the vehicle is standing – accident!

- Place the headphones while driving, so that in case of breaking or accident nobody can be injured.
Note

- In case of connection was not successful, turn off the wireless headphone off and repeat the
coupling process. Other problem solutions are described below.

- At too high and too low volume level, the wireless headset will be automatically set to a fixed value
while coupling the process.

- After turning the RSE off the wireless headset will switch after about five minutes automatically off.
Teach and mark the wireless headphone

The wireless headphones have to be unique trained and identified to the RSE. The programming

procedure must be run separately for the left / right wireless headphones. Depending on which side of
the RSE control unit to start the learning process, the wireless headset to the left / right RSE display is
assigned. The assignment of the headphones to the left / right RSE display is marked with a sticker.

Figure 106 Wireless Headphones feature
teach wireless Headphones

Prerequisite: The protective film of the battery cover is removed - see Figure 107 - and
the wireless headset is off.
► Keep the Power Button (1) pressed - see Figure 105 (R) for at least 5 seconds until the LED (2)
starts to flash and then flashes fast. The wireless headphones are prepared for the learning process.

► Press the MENU button.
► Press the Control key setup RSE.
► Turn the control knob on the headphones and press the control button.
► Turn the control knob to look for wireless headphones and press the control button.
► Click OK to confirm that the wireless headset is switched on and in the search mode. The available

wireless headphones appear after short time in RSE display.
► Turn the control knob to the desired headset and press the control button. The wireless
headphones are taught for the RSE. Once the wireless headset is trained successfully, a message
appears on the RSE display.
► Repeat process for the second wireless headset.

mark Wireless Headphone
Requirement: The wireless headphones are taught - see above -
► Attach the sticker (1) or (2) on the inside of the left / right wireless headphones.

Note

- After switching the RSE on, the connection is stored to the once taught and switched on wireless
headset automatically.

- The RSE only works with wireless headsets provided by the Audi dealership.

- During the programming procedure, the audio / video playback via wireless headphones is stopped.

Wireless Headphones delete
If a headphone will be exchanged or the assignment should be changed, you can delete the

connection between the wireless headset and the RSE.
Prerequisite: A wireless headset is taught for the RSE

► Press the MENU button.
► Press the Control key to setup the RSE.
► Turn the control knob on the headphones and press the control button.
► Turn the control knob to delete wireless headset and press the control button. The connection

between the wireless headset and the RSE will be deleted.
Battery charge / replace batteries

Once the diode on the wireless headset turns to red, the Akku’s / batteries are weak and should be
changed or in case of installed Akku’s reloaded.