MULF2
Certification
Installation instruction
Harman/Becker reserves the copyright to this document. It must not be copied, communicated or made available to third parties without the written authorisation of Harman/Becker
Department EDH
Date Name
Drawn
Check
Rel.
QME Page
01 21.03.06 Schneid Automotive Systems of 55
Rev. Change / Note Date Name File Installation Printed. 21.03.06
Harman/Becker
MULF2
Certification
Installation instruction
1
Inhaltsverzeichnis
1 Abstract ...........................................................................................................................3
1.1 Revision index............................................................................................................ 3
1.2 Applicable documents................................................................................................3
1.3 Abbreviations ............................................................................................................. 4
1.4 Purpose of the document...........................................................................................5
2 General............................................................................................................................. 5
3 Power supply................................................................................................................... 5
4 Antenna............................................................................................................................ 5
5 FCC note.......................................................................................................................... 5
Harman/Becker reserves the copyright to this document. It must not be copied, communicated or made available to third parties without the written authorisation of Harman/Becker
Page 2 - EDH
Revision 01 vom 21.03.06 of Installation instruction_MULF2.doc
5
Printed: 21.03.06
MULF2
Certification
Installation instruction
1 Abstract
1.1 Revision index
No. State Version Change Description Changed pages Autor
1 ready 1.0 All Schneider
1.2 Applicable documents
Ref. State Version Document Description Autor
Harman/Becker reserves the copyright to this document. It must not be copied, communicated or made available to third parties without the written authorisation of Harman/Becker
Page 3 - EDH
Revision 01 vom 21.03.06 of Installation instruction_MULF2.doc
5
Printed: 21.03.06
Installation instruction
1.3 Abbreviations
Document Description
BT Bluetooth
EC Echo cancellation
NR Noise reduction
MULF2
Certification
Harman/Becker reserves the copyright to this document. It must not be copied, communicated or made available to third parties without the written authorisation of Harman/Becker
Page 4 - EDH
Revision 01 vom 21.03.06 of Installation instruction_MULF2.doc
5
Printed: 21.03.06
MULF2
Certification
Installation instruction
1.4 Purpose of the document
Installation instruction for the MULF2.
2 General
The MULF2 is not sold direct to the customer. The MULF2 will be delivered directly to the car
manufacturer. MULF2 is manufactured for BMW AG.
BMW AG is responsible for the correct installation of the MULF2. This document is a guide for the
correct installation of the MULF2.
3 Power supply
Normal operation voltage of the MULF2 is 9V – 16V. The nominal supply current of the MULF2 is
180 mA at 14V. The MULF2 may only be operated on a fused power supply. The recommended
fuse is a 10A Type.
4 Antenna
The MULF2 has an external antenna connector. The connector is a FAKRA type. Only the
following antenna should be connected to the MULF2:
• 6 928 461 (BMW part number)
This antenna has a gain of 2,1 dBi.
It is possible, to connect the antenna via a coax cable.
5 FCC note
In the user manual should be the following text:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.
Harman/Becker reserves the copyright to this document. It must not be copied, communicated or made available to third parties without the written authorisation of Harman/Becker
Page 5 - EDH
Revision 01 vom 21.03.06 of Installation instruction_MULF2.doc
5
Printed: 21.03.06
Loading...