Harman MPMI, MFXI User Manual

USER GUIDE

soundcraft@harman.com

This equipment complies with the EMC Directive 2004/108/EC and LVD 2006/95/EC

IMPORTANT

Please read this manual carefully before using

your mixer for the rst time.

Soundcraft is a trading division of Harman International Industries Ltd. Information in this manual is subject to change without notice and does not represent a commitment on the part of the vendor. Soundcraft shall not be liable for any loss or damage whatsoever arising from the use of information or any error contained in this manual.

No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, electrical, mechanical, optical, chemical, including photocopying and recording, for any purpose without the express written permission of Soundcraft.

Harman International Industries Limited Cranborne House Cranborne Road POTTERS BAR Hertfordshire EN6 3JN UK

Tel: +44 (0)1707 665000 Fax:+44 (0)1707 660742 http://www.soundcraft.com

2 Soundcraft MFXi MPMi User Guide Issue 1210

Contents

IMPORTANT SAFETY INSTRUCTIONS..............................................................................4

SAFETY SYMBOL GUIDE...................................................................................................6

INTRODUCTION................................................................................................................11

THE 60-SECOND GUIDE - MFXi.......................................................................................12

THE 60-SECOND GUIDE - MPMi......................................................................................14

WIRING UP.........................................................................................................................16

BLOCK DIAGRAM - MFXi...................................................................................................20

BLOCK DIAGRAM - MPMi..................................................................................................21

MONO INPUT CHANNELS (MFXi shown)..........................................................................22

STEREO INPUT CHANNELS (MFXi shown)......................................................................25

MASTER SECTION (MFXi).................................................................................................28

MASTER SECTION (MPMi)................................................................................................29

Lexicon® FX PROCESSOR OVERVIEW ...........................................................................33

FX OPERATION...................................................................................................................33

FX PROCESSOR CONTROLS (MFXi only).........................................................................34

REVERBS ...........................................................................................................................35

REVERB CONTROLS..........................................................................................................36

DELAYS................................................................................................................................37

DELAY CONTROLS ............................................................................................................37

MODULATED EFFECTS......................................................................................................38

FACTORY RESET ...............................................................................................................39

EFFECTS DATA CHART.......................................................................................................40

MFXi/MPMi TYPICAL SPECIFICATIONS.............................................................................41

USING YOUR MFXi/MPMi CONSOLE.................................................................................42

MFXi MARK-UP SHEETS.....................................................................................................44

MPMi MARK-UP SHEETS....................................................................................................45

FITTING OPTIONAL RACK-MOUNT BRACKETS ..............................................................46

DIMENSIONS.......................................................................................................................47

APPLICATIONS....................................................................................................................48

TYPICAL CONNECTING LEADS.........................................................................................52

GLOSSARY...........................................................................................................................54

WARRANTY..........................................................................................................................56

3Soundcraft MFXi MPMi User Guide Issue 1210

IMPORTANT SAFETY INSTRUCTIONS

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

Do not use this apparatus near water.

Clean only with a dry cloth.

Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

Do not install near any heat sources such as radiators, heat registers, stoves, or other

apparatus (including ampliers) that produce heat.

Do not defeat the safety purpose of a polarised or grounding type plug. A polarised plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided

for your safety. If the provided plug does not t into your outlet, consult an electrician

for replacement of the obsolete outlet

Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles and the point where they exit from the apparatus.

Only use attachments/accessories specied by the manufacturer.

Use only with the cart, stand, tripod, bracket or table specied by the manufacturer,

or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

Unplug this apparatus during lightning storms or when unused for long periods of time.

Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Note: It is recommended that all maintenance and service on the product should be carried out by Soundcraft or its authorised agents. Soundcraft cannot accept any liability whatsoever for any loss or damage caused by service, maintenance or repair by unauthorised personnel.

WARNING: To reduce the risk of re or electric shock, do not expose this apparatus

to rain or moisture.

Do not expose the apparatus to dripping or splashing and do not place objects lled

with liquids, such as vases, on the apparatus.

4 Soundcraft MFXi MPMi User Guide Issue 1210

No naked ame sources, such as lighted candles, should be placed on the apparatus.

Ventilation should not be impeded by covering the ventilation openings with items such as newspapers, table cloths, curtains etc. THIS APPARATUS MUST BE EARTHED. Under no circumstances should the safety earth be disconnected from the mains lead.

The mains supply disconnect device is the mains plug. It must remain accessible so as to be readily operable when the apparatus is in use.

If any part of the mains cord set is damaged, the complete cord set should be replaced. The following information is for reference only. The wires in the mains lead are coloured in accordance with the following code:

Earth (Ground): Green and Yellow (US - Green/Yellow) Neutral: Blue (US - White)

Live (Hot): Brown (US - Black) As the colours of the wires in the mains lead may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:

The wire which is coloured Green and Yellow must be connected to the terminal in

the plug which is marked with the letter E or by the earth symbol.

The wire which is coloured Blue must be connected to the terminal in the plug

which is marked with the letter N

The wire which is coloured Brown must be connected to the terminal in the plug

which is marked with the letter L

Ensure that these colour codes are followed carefully in the event of the plug being

changed

This unit is capable of operating over a range of mains voltages as marked on the rear panel.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

This Class A digital apparatus meets the requirements of the Canadian Interference-Causing Equipment Regulations.

Cet appareil numérique de la Classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

5Soundcraft MFXi MPMi User Guide Issue 1210

For your own safety and to avoid invalidation of the warranty please read this

section carefully.

SAFETY SYMBOL GUIDE

For your own safety and to avoid invalidation of the warranty all text marked with these symbols should be read carefully.

WARNINGS

The lightning ash with arrowhead symbol, is intended to

alert the user to the presence of un-insulated “dangerous

voltage” within the product’s enclosure that may be of

sufcient magnitude to constitute a risk of electric shock to

persons.

CAUTIONS

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in the

literature accompanying the appliance.

NOTES

Contain important information and useful tips on the

operation of your equipment.

HEADPHONES SAFETY WARNING

Contain important information and useful tips on headphone

outputs and monitoring levels.

Recommended Headphone Impedance >= 32 Ohms.

6 Soundcraft MFXi MPMi User Guide Issue 1210

7Soundcraft MFXi MPMi User Guide Issue 1210

CONSIGNES DE SÉCURITÉ IMPORTANTES

Lisez ces instructions.

Conservez ces instructions.

Respectez toutes les consignes de sécurité.

Suivez toutes les instructions.

N’utilisez pas cet appareil près d’une source liquide.

Nettoyez l’appareil uniquement avec un tissu sec.

N’obstruez pas les ouïes de ventilation. Installez uniquement en suivant les recommandations du fabricant.

N’installez pas cet appareil près d’une source de chaleur, comme un radiateur, une

chaudière ou tout autre appareil (amplicateurs inclus) générant de la chaleur.

Ne modiez pas les protections de la che secteur. Les ches polarisées sont équipées d’une lame plus large que l’autre. Les ches avec mise à la terre disposent de deux

lames et d’une broche pour la terre. Ce dispositif garantit votre sécurité contre toute

électrocution. Si la che fournie ne correspond pas au format de vos prises murales,

consultez un électricien pour faire remplacer vos prises.

Protégez le cordon secteur contre tout dommage physique (pincement, etc.), plus

particulièrement au niveau des ches, des prises et de l’embase secteur.

Utilisez uniquement avec les accessoires/xations spéciés par le fabricant.

Utilisez uniquement avec un chariot, pied, trépied, xation ou table spécié par le fabricant ou vendu avec le produit. Lorsque vous utilisez un chariot, veillez à assurer

sa stabilité pour éviter toute chute.

Déconnectez l’appareil du secteur lors des orages ou des longues périodes d’inutilisation.

Conez toutes les réparations à un personnel qualié. Faites contrôler le produit s’il a été endommagé (che secteur ou cordon secteur endommagés, par exemple), s’il y a eu inltration de liquide ou d’objets dans le boîtier, si l’appareil a été exposé à la pluie ou à l’humidité, s’il ne fonctionne pas normalement ou s’il est tombé.

Remarque : Nous vous recommandons de coner toutes vos réparations à un centre

agréé par Soundcraft. Soundcraft n’accepte aucune responsabilité pour les réparations ou entretiens effectués par un personnel qui n’est pas agréé.

8 Soundcraft MFXi MPMi User Guide Issue 1210

ATTENTION : Pour réduire les risques d’incendie ou d’électrocution, n’exposez pas ce

produit à la pluie ou à l’humidité.

Ce produit ne doit être exposé à aucune source liquide, et aucun contenant rempli de

liquide, tel un vase, ne doit être déposé sur celui-ci.

Ne placez aucune source à amme nue, telle une bougie, sur l’appareil.

Veillez à ce qu’aucun objet (journal, nappe, rideau, etc.) n’obstrue les ouïes de ventilation. CET APPAREIL DOIT ÊTRE RELIÉ À LA TERRE. La broche de mise à la terre ne doit en aucun

cas être déconnectée du cordon ou de la prise secteur.

Pour déconnecter l’appareil du secteur, déconnectez le cordon secteur de l’embase secteur ou de la prise secteur. Celles-ci doivent rester accessibles en tout temps.

Faites remplacer le cordon secteur si l’une des parties est endommagée. Les informations ci-dessous ne servent que de références.

Les ls du cordon secteur sont repérés par des couleurs :

Terre (Masse) : Vert et Jaune (US - Vert/Jaune) Neutre : Bleu (US - Blanc) Phase (Point chaud) : Marron (US - Noir)

Si les couleurs ou les codes sont différents dans votre région, procédez comme suit :

Le l Vert et Jaune doit être connecté à la borne repérée par la lettre E ou par le symbole

de terre/masse.

Le l Bleu doit être connecté à la borne N (neutre) de la prise. Le l Marron doit être connecté à la borne L (phase). Si vous devez remplacer la prise ou la che secteur, veillez à assurer le respect des couleurs et le raccordement à la terre, au neutre et à la phase.

La console ne peut être reliée qu’à une ligne secteur de la tension indiquée en face arrière.

REMARQUE : Suite aux tests effectués, il est établi que ce produit répond aux normes de l’alinéa 15 des réglementations fédérales américaines sur les produits numériques de

Classe A. Ces normes sont établies an de vous protéger contre toute interférence nuisible

en installation commerciale. Cet appareil génère, utilise et émet des fréquences radio. Par conséquent, s’il n’est pas installé et utilisé en suivant les instructions, il peut causer des interférences nuisibles aux communications radio. L’utilisation en environnement résidentiel peut causer des interférences. L’utilisateur doit alors faire corriger le problème

à ses frais. Cet appareil numérique de Classe A répond aux normes canadiennes sur le

brouillage radioélectrique.

Cet appareil numérique de la Classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

9Soundcraft MFXi MPMi User Guide Issue 1210

Pour assurer votre sécurité et éviter toute annulation de la garantie, veuillez lire

attentivement les paragraphes repérés par ces symboles de sécurité.

GUIDE DES SYMBOLES DE SÉCURITÉ

Pour assurer votre sécurité et éviter toute annulation de la

garantie, veuillez lire attentivement les paragraphes repérés par ces symboles de sécurité.

AVERTISSEMENT

Le symbole de l’éclair avec une èche prévient l’utilisateur

d’une tension dangereuse non isolée dans le boîtier de

l’appareil, pouvant être sufsamment forte pour constituer

un risque d’électrocution pour les personnes exposées.

ATTENTION !

Le point d’exclamation dans un triangle signale à l’utilisateur

la présence d’instructions importantes pour l’utilisation et

l’entretien dans le mode d’emploi fourni avec l’appareil.

REMARQUES

Informations utiles sur l’utilisation de la console.

CONSIGNES DE SÉCURITÉ POUR L’UTILISATION DE L’EMBASE

CASQUE

Informations importantes et astuces pratiques pour les

embases casques et les niveaux d’écoute.

Impédance minimum recommandée pour le casque : >

32 Ohms.

10 Soundcraft MFXi MPMi User Guide Issue 1210

INTRODUCTION

Thank you for purchasing a Soundcraft MPMi/MFXi mixer. The MPMi and MFXi ranges are our most cost-effective mixing solutions, bringing you all the features and performance that you expect from a Soundcraft product, at an extraordinarily low price. The packaging, in which your console arrived, forms part of the product and must be retained for future use.

Owning a Soundcraft console brings you the expertise and support of one of the industry’s leading manufacturers, and the results of over three decades of supporting some of the biggest names in the business. Our knowledge has been attained through working in close contact with leading professionals and institutes to bring you products designed to get the best possible results from your mixing. Built to the highest standards using quality components and surface mount technology, the MPMi/MFXi is designed to be as easy to use as possible. We have

spent years researching the most efcient methods of control for two key reasons:

1) Engineers, musicians, writers and programmers all need to have very few interruptions to the creative process; our products have been designed to be almost transparent, allowing this process to breathe.

2) Whether performing or recording, time is a very expensive and rare commodity. Our products have a user interface which is recognised by millions to

be the industry standard because of its efciency.

The sonic qualities of our products are exemplary - some of the same circuits which are used on our most expensive consoles are employed in the MPMi/ MFXi, bringing you the great Soundcraft quality in a small format console without compromise. You will also be glad to know you have a one year warranty with your product from the date of purchase. The MPMi/MFXi has been designed using the latest high-end software based engineering packages. Every console from Soundcraft has been proven to stand up to all the stress and rigours of modern day mixing environments. The entire MPMi/MFXi range is manufactured using some of the most advanced techniques in the world, from high density surface mount PCB technology, to computer aided test equipment able to measure signals well outside the range of normal hearing. As each console passes through to be quality checked before packing, there is also a human listening station. Something we have learnt over the years is that the human touch counts - and only by using people can you ensure the product meets the high demands of the user.

ADVICE FOR THOSE WHO PUSH THE BOUNDARIES

Although your new console will not output any sound until you feed it signals, it has

the capability to produce sounds which when monitored through an amplier or

headphones can damage hearing over time. Please take care when working with your audio - if you are manipulating controls which you don’t understand (which we all do when we are learning), make sure your monitors are turned down. Remember that your ears are the most important tool of your trade, look after them, and they will look after you.

Most importantly - don’t be afraid to experiment to nd out how each parameter

affects the sound - this will extend your creativity and help you to get the best from your mixer and the most respect from your artists and audience.

11Soundcraft MFXi MPMi User Guide Issue 1210

THE 60-SECOND GUIDE - MFXi

S.HALL L.HALL V.HALL D.HALL S.PLT L.PLT V.PLT D.PLT ROOM STUDIO CHMBR AMB ARENA GATED REV

SPRING

1 2 3 4 5 6 7 8 9 10 1

1 12 13 14 15

S.DLY D.DLY T.DLY P.DLY M.DLY R.DLY CHORUS FLANGR PHASR TREM/P

VIBRTO RV/DL S RV/DL L PHSDEL ROTDEL

24-BITDIGITAL

EFFECTSPROCESSOR

A:PRE-DEL B:TME/SPD

A B

:VARI

AFL

MONI TOR OUT

MIC MIC MIC MIC MIC MIC MIC MIC MIC MIC MIC MIC

HF HF HF HF HF HF HF HF HF HF HFHF

LFLF LF LF LF LF LF LF LF LF LF LFLF

MF MF MF MF MF MF MF MF MF MF MFMF

1 2 3 4 5 6 7 8 9 10 11 12

3 3

9 9

15 15

3 3

9 9

15 15

3 3

9 9

15 15

3 3

9 9

15 15

3 3

9 9

15 15

3 3

9 9

15 15

3 3

9 9

15 15

3 3

9 9

15 15

3 3

9 9

15 15

3 3

9 9

15 15

3 3

9 9

15 15

3 3

9 9

15 15

3 3

9 9

15 15

3 3

9 9

15 15

3 3

9 9

15 15

3 3

9 9

15 15

3 3

9 9

15 15

3 3

9 9

15 15

3 3

9 9

15 15

3 3

9 9

15 15

3 3

9 9

15 15

3 3

9 9

15 15

3 3

9 9

15 15

3 3

9 9

15 15

3 3

9 9

15 15

3 3

9 9

15 15

3 3

9 9

15 15

3 3

9 9

15 15

3 3

9 9

15 15

3 3

9 9

15 15

3 3

9 9

15 15

3 3

9 9

15 15

0 10 0 10 0 10 0 10

0 10

0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 100 10

0 10 0 10 0 100 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 10 0 100 10

L L LLLLLLLLLLL LL R R RRRRRRRRRRR RR

3 3

9 9

15 15

3 3

9 9

15 15

3 3

9 9

15 15

3 3

9 9

15 15

3 3

9 9

15 15

3 3

9 9

15 15

3 3

9 9

15 15

3 3

9 9

15 15

3 3

9 9

15 15

3 3

9 9

15 15

3 3

9 9

15 15

3 3

9 9

15 15

3 3

9 9

15 15

750

150

3.5k

750

150

3.5k

750

150

3.5k

750

150

3.5k

750

150

3.5k

750

150

3.5k

750

150

3.5k

750

150

3.5k

750

150

3.5k

750

150

3.5k

750

150

3.5k

750

150

3.5k

750

150

3.5k

GAINGAIN GAIN GAIN GAIN GAIN GAIN GAIN GAIN GAIN GAIN GAINGAIN

AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1

AUX2 AUX2 AUX2 AUX2 AUX2 AUX2 AUX2 AUX2 AUX2 AUX2 AUX2AUX2 AUX2 AUX2 AUX2 AUX2 AUX2 AUX2 AUX2 AUX2 AUX2 AUX2 AUX2 AUX2

FX FX FX FX FX FX FX FX FX FX FXFX F

X FX FX FX FX FX FX FX FX FX FX FX

PAN PAN PAN PAN PAN PAN PAN PAN PAN PAN PANPA PN AN PAN PAN PAN PAN PAN PAN PAN PAN PAN BAL BAL

0 0 00 00000000000

PFL PFL PFL PFLPFL PFL PFL PFL PFL PFL PFL PFL PFL PFL PFLPFL

MIX SUB

POST PRE

MIX SUB

PK PK PK PKPK PK PK PK PK PK PK PK PK PK PKPK

SP SP SP SPSP SP SP SP SP SP SP SP SP SP SPSP

5 5 5 5 5 5 5 5 5 5 5 5

0 0 0 0 0 0 0 0 0 0 0 0

-5 -5 -5 - 5 - 5 -5 -5 -5 - 5 -5 -5 -5

-10 - 10 -10 -10 -10 -10 -10 -10 -10 -10 -10 -10

-20 - 20 -20 -20 -20 -20 -20 -20 -20 -20 -20 -20

-30 - 30 -30 -30 -30 -30 -30 -30 -30 -30 -30 -30

MUTE

MUTE MUTEMUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTEMUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTEMUTE

12 STE1

STE2

2 3 4 5 6 7 8 9 10 11

REC OUT

2TRK

LEVEL

0 10

STEREO1 STEREORETURN

L L L

R R R

[MONO] [MONO] [MONO]

MNTR

TOMIX

MIX-L

MIX-R

-3

-6

-12

-16

-22

MIX/ SOLO

PHANTOM POWER

BANKA

BANKB

GAIN GAIN LEVEL

HF HF

MF MF

LF LF

AUX1 OUT

AUX2 OUT

FXBUS OUT

MONO OUT

STORE

TEMPO

TAP

BANKA BANKB

2TRK

SUBTO

MIX

MNTR LEVEL

LEVEL

STE

MNO

MIX SUB

FXTO AUX1

FXTO AUX2

-5

-10

-20

-30

-5

-10

-20

-30

-5

-10

-20

-30

-5

-10

-20

-30

A:DECAY B:FBK/DPTH

MUTE FX

-10 20dB -10 20dB

48V

HEADPHONES

10 10 10 10 10 10 10 10 10 10 10 10 10 10

EFFECTS21 3 4 5 6 7 8 9 10 11 12 STE1 STE2 SUB-L

SUB-R MIX

LINELINELINELINELINE LINELINE LINE LINE LINE LINE LINE LINE

INSERTINSERTINSERTINSERTINSERTINSERT INSERT INSERT INSERT INSERT INSERT I NSERT INSERT

SOLO PWR

AUX1 MST

AUX2 MST

FX MST

SUBOUT

-5

-10

-15

-20

-30

-40

26 17

38 33

10 11

13 14

KARAOKE

To get you working as fast as possible, this manual begins with a 60-second guide. Here you can nd quick

information on any feature of the console. This shows the MFXi console.

12 Soundcraft MFXi MPMi User Guide Issue 1210

1 MIC INPUT (XLR) Connect Microphones here. If you are using a condenser mic, ensure phantom

power is supplied by pressing the switch at the top of the master section.

WARNING: Do Not apply Phantom Power

2 LINE INPUT (¼” Jack) Connect Line level sources here, e.g. Synth, Drum Machine, DI etc. 3 INSERT POINT (¼” Jack) Connect Signal processors here, e.g. Compressor, Gate etc. 4 GAIN CONTROL Adjust this to increase or decrease the level of the incoming signal. 5 HPF The high-pass lter reduces the level of bass frequencies only. Use this in live PA

6 EQ STAGE Adjust these controls to change the signal tone (the character of the signal).

before connecting a microphone.

situations to reduce stage rumble or ‘popping’ from mics.

7 AUX 1 & 2 SENDS Adjust these controls to change the level of the signal to an artist’s monitors

(headphones/in-ear/stage monitors). Aux 1 send is pre-fade. Aux 2 is globally switchable pre/post fade.

8 FX SEND This control sets the level of the post-fade signal being sent to the FX bus; from

there it is routed to the FX processor.

9 PAN CONTROL Use this control to position the signal within the stereo eld. 10 MUTE SWITCH When this is pressed you will hear no signal from the channel. 11 PFL When pressed the signal will appear on the monitor and headphone outputs - use

Your MFXi console is equipped with a Kensington® Security slot on the rear panel for use with compatible PC/Laptop security cables. For more information about the Kensington range of security devices please visit http://us.kensington.com

this to monitor the post-EQ signal from the channel.

12 MIX/SUB SWITCH When this switch is up, the channel’s post-pan-pot signal is routed to the Mix (left

and right) buses. When the switch is depressed, the post-pan-pot signal is routed to the Sub-group (left and right) buses.

13 PEAK LED This is used to indicate that the signal is close to distorting (clipping) on a specic

channel.

14 SP LED The SP LED glows when a signal is present. The feed point for the LED is post-insert,

pre-EQ.

15 INPUT CHANNEL FADER This is used to control the level fed to the Mix Bus and post-fade sends. 16 MIX OUTPUTS (XLR) Connect these to your analogue recording device, or to your amplication system. & MONO OUT (¼” Jack) 17 SUB-GROUP OUTPUTS These outputs can be connected to a separate amplier system or to an external (¼” Jack) processor. 18 SUB-GROUP ROUTING The sub-group mix can be routed to the main mix, in mono or stereo. 19 MASTER FADERS These faders control the overall level of the mix and sub-group outputs. 20 MAIN METERS These show the level of the mix outputs. When the master SOLO LED is lit, the meters

show the level of the selected AFL/PFL signal.

21 MONITOR OUTPUTS These are used to feed your monitoring system. This can be directly connected to (¼” Jack) powered monitors, or indirectly via an amplier to standard monitors. 22 MONITOR CONTROL This controls the level of the signal sent to your monitoring system. 23 MONITOR SELECT SWITCH This switch selects the signal source to be monitored. Note that the 2-TK input can

be monitored also, see item 31 below.

24 PHONES CONTROL This controls the level of the signal sent to the headphones jack socket. 25 HEADPHONES (¼” Jack) Plug your headphones into this socket. Recommended headphones impedance is

32 ohms or greater.

26 AUX 1 & 2 OUTPUTS (¼” Jacks) 27 AUX CONTROLS The rotary controls set the output levels of the two Aux Outputs. The After Fade & AFL SWITCHES (AFL) Listen switches route their respective aux output signal to the monitor/

28 AUX 2 POST/PRE SWITCH This switch globally changes the AUX 2 feed on all the input modules to be either

29 STEREO INPUTS (¼” Jack) These two pairs of inputs can be used to connect line level stereo inputs from key-

30 2-TRACK IN 31 2-TRACK OUT Use these to control the 2 Track signal. The MONITOR switch sends the signal to the

32 RECORD OUTPUTS 33 PHANTOM POWER Press this to globally switch the phantom power (48V) on for condenser microphones.

WARNING: Do Not apply Phantom Power before

34 STEREO RETURN INPUTS This pair of inputs accept 3-pole ‘A’ gauge (TRS) jacks. Use these inputs for sources

35 STEREO RETURN CONTROL This control sets the level of signal routed to the main mix busses. 36 FX BUS OUTPUT This output carries the signal from the FX bus. It could be used as a third Aux Output

37 FX CONTROL & AFL SWITCH The rotary control regulates the signal level being fed from the FX bus to the FX

38 FOOTSWITCH CONNECTOR This is used by the FX Processor, see page 33. 39 LEXICON® FX PROCESSOR See the information starting on page 33 .

(RCA Phono)

These outputs can be used to send the channel signal to an artist’s monitors (head phones/in-ear/stage monitors), external FX or secondary PA/monitor system.

headphones outputs.

post-fade or pre-fade.

boards, sound modules, samplers, computer based audio cards etc. These inputs pass through a stereo channel strip, with EQ, Auxes and a Balance control. Mono sources may be used by plugging into the left jack only.

You can connect the playback from your recording device here.

monitor outputs and phones, whilst the TO MIX switch sends it to the main mix.

You can connect these to the inputs of your recording device.

connecting a microphone.

such as keyboards, drum machines, synths or CDs. The inputs are BALANCED. Mono sources may be used by plugging into the left jack only.

if desired if the FX Processor is not needed at the time. The FX sends on the inputs channels to the FX bus are always post-fade.

processor and to the FX BUS OUTPUT socket. The After-Fade Listen (AFL) switch routes this post-FX-control, pre-FX signal to the monitor/headphones outputs.

13Soundcraft MFXi MPMi User Guide Issue 1210

THE 60-SECOND GUIDE - MPMi

To get you working as fast as possible, this manual begins with a 60-second guide. Here you can nd quick

information on any feature of the console. .

25 16

1 2 3 4 5 6 7 8 9 10 1 1 12

MIC MIC MIC MIC MIC MIC MIC MIC MIC MIC MIC MIC

LINELI NELINELINELIN E LINELINE LINE LINE LINE LINE LINE LINE

3 3

HF HF HF HF HF HF HF HF HF HF HFHF

9 9

15 15

750

MF MF MF MF MF MF MF MF MF MF MFMF

150

3.5k

3 3

9 9

15 15

3 3

9 9

15 15

9 9

15 15

LF LF LF LF LF LF LF LF LF LFLF

9 9

15 15

3 3

9 9

15 15

750

150

3 3 6

9 9

15 15

3 3

9 9

15 15

150

3.5k

3 3

9 9

15 15

3 3

9 9

15 15

750

3.5k

3 3

9 9

15 15

750

150

3 3

9 9

15 15

3 3

9 9

15 15

3 3

9 9

15 15

150

3.5k

3 3

9 9

15 15

3 3

9 9

15 15

750

3.5k

AUX2AUX2AUX2AUX2AUX2 AUX2 AUX2

3 3

9 9

15 15

750

150

3 3 6

9 9

15 15

3 3

9 9

15 15

150

3.5k

3 3

9 9

15 15

3 3

9 9

15 15

3.5k

3 3

9 9

15 15

750

150

3 3 6

9 9

15 15

3 3

9 9

15 15

3 3

9 9

15 15

150

3.5k

3 3

9 9

15 15

3 3

9 9

15 15

750

3.5k

3 3

9 9

15 15

750

150

3.5k

3 3

9 9

15 15

3 3

9 9

15 15

AUX1AUX1AUX1AUX1AUX1AUX1AUX1AUX1AUX1AUX1AUX1 AUX1AUX1AUX1AUX1AUX1AUX1AUX 1AUX1AUX1AUX1 AUX1 AUX1

AUX1 AUX1

0 100 100 100 100 100 100 100 100 100 100 10 0 10 0 100 100 100 100 100 100 100 100 100 100 100 10

0 10 0 100 100 100 100 100 100 100 100 100 100 100 10 0 10 0 100 10 0 100 100 100 100 100 100 100 100 100 100 100 10

MIX SUB

00000000 0 0 0000000000000

LLLLLLLL L L LLLLLLLLLLLL LR RRRRRRR R R RRRRRRRRRRRR R

MIX SUB

PAN PAN PAN PAN PAN PAN PAN PAN PAN PAN PAN PAN BAL BA L

10 11

12 13

2 3 4 5 6 7 9 1 0 111

MIX

SUB

10 10 10 10 10 10 10 10 10 10 10 10 10 10

5 5 5 5 5 5 5 5 5 5 5 5

0 0 0 0 0 0 0 0 0 0 0 0

-5 -5 -5 -5 -5 -5 -5 -5 -5 -5 -5 -5

-10 -1 0 -10 -10 -10 -10 -10 -10 -10 -10 -10 -10

-20 -2 0 -20 -20 -20 -20 -20 -20 -20 -20 -20 -20

-30 -30 -30 -30 -30 -30 -30 -30 -30 -30 -30 -30

SUB

MIX

SUB

MUTE MUTE

MIX SUB

MUTE

MIX

SUB

MONITOR OUT

AUX1 OUT

INSERTINSERTINSERTINSERTINSERTINSERT INSERT INS ERT INSERT INSERT INSERT INSERT INSERT

L L

GAINGAIN GAIN GAIN GAIN GAIN GAIN GAIN GAIN GAIN GAIN GAINGAIN

[MONO] [MONO]

R R

STEREO 1

3 3

9 9

15 15

-10 20dB -10 20dB

750

3 3

9 9

15 15

150

3.5k

3 3

9 9

15 15

3 3

9 9

15 15

0 10

AUX2AUX2AUX2AUX2AUX2AUX 2AUX2

0 100 100 100 100 100 100 100 100 100 100 100 10 0 10 0 100 100 100 100 100 100 100 100 100 100 100 100 10

AUX3AUX3AUX3AUX3AUX3AUX3AUX3AUX3AUX3AUX3AUX3AUX3 AUX3 AUX3

STE1

MUTE

PFL PFL PFLPFL PFL PFL PFL PFL PFL PFL PFL PFL PFL PFLPFL

MIX

MIX SUB

SUB

PK PK PKPK PK PK PK PK PK PK PK PK PKPK

SP SP SPSP SP S P SP SP SP SP SP SP SPSP

AUX2 OUT

GAIN GAIN

GAIN

HF HF

9 9

MF MF

9 9

LF LF

9 9

-5

-10

-20

-30

SUB OUT

3 3

15 15

3 3

15 15

3 3

15 15

STE2

MUTEMUTE MUTE MUTE MUTE MUTE MUTE MUTE MUT EMUTE MUTE MUTE MUTE MUTE MUTEMUTE

MIX SUB

MONO

OUT

AUX3

OUT

0 10

TOM IX

MNTR

0 10

MIX SUB

STE

MNO

SUB TO

MIX

-5

-10

-20

-30

48V

PHANTOM POWER

REC OUT

MIX-L

2TRK

LEVEL

MIX-R

HEADPHONES

0 10

AFL

0 10

AFL

POST PRE

0 10

AFL

MIX/ SOLO

-3

-6

-12

-16

-22

LEVEL

AUX1 MST

AUX2 MST

AUX3 MST

MNTR LEVEL

SOLO PWR

-5

-10

-20

-30

-5

-10

-20

-30

21 3 4 5 6 7 8 9 10 11 12

STE1 STE2 SUB-L

SUB-R MIX

1 MIC INPUT (XLR) Connect Microphones here. If you are using a condenser mic, ensure phantom

power is supplied by pressing the switch at the top of the master section.

WARNING: Do Not apply Phantom Power before

connecting a microphone.

situations to reduce stage rumble or ‘popping’ from mics.

6 EQ STAGE Adjust these controls to change the signal tone (the character of the signal). 7 AUX SENDS Adjust these controls to change the level of the signal to an artist’s monitors

(headphones/in-ear/stage monitors). Aux 1 send is pre-fade. Aux 2 is globally switchable pre/post fade, Aux 3 send is post-fade

8 PAN CONTROL Use this control to position the signal within the stereo eld. 9 MUTE SWITCH When this is pressed you will hear no signal from the channel. 10 PFL When pressed the signal will appear on the monitor and headphone outputs - use

this to monitor the post-EQ signal from the channel.

11 MIX/SUB SWITCH When this switch is up, the channel’s post-pan-pot signal is routed to the Mix (left

and right) buses. When the switch is depressed, the post-pan-pot signal is routed to the Sub-group (left and right) buses.

14 Soundcraft MFXi MPMi User Guide Issue 1210

12 PEAK LED This is used to indicate that the signal is close to distorting (clipping) on a specic

channel.

13 SP LED The SP LED glows when a signal is present. The feed point for the LED is post-insert,

pre-EQ.

14 INPUT CHANNEL FADER This is used to control the level fed to the Mix Bus and post-fade sends. 15 MIX OUTPUTS (XLR) Connect these to your analogue recording device, or to your amplication &

MONO OUT (¼” Jack) system.

16 SUB-GROUP OUTPUTS These outputs can be connected to a separate amplier system or to an external

(¼” Jack) processor.

17 SUB-GROUP ROUTING The sub-group mix can be routed to the main mix, in mono or stereo. 18 MASTER FADERS These faders control the overall level of the mix and sub-group outputs. 19 MAIN METERS These show the level of the mix outputs. When the master SOLO LED is lit, the meters

show the level of the selected AFL/PFL signal.

20 MONITOR OUTPUTS These are used to feed your monitoring system. This can be directly connected to

(¼” Jack) powered monitors, or indirectly via an amplier to standard monitors.

21 MONITOR CONTROL This controls the level of the signal sent to your monitoring system. 22 MONITOR SELECT SWITCH This switch selects the signal source to be monitored. Note that the 2-TK input can

be monitored also, see item 30 below.

23 PHONES CONTROL This controls the level of the signal sent to the headphones jack socket. 24 HEADPHONES (¼” Jack) Plug your headphones into this socket. Recommended headphones impedance is

32 ohms or greater.

25 AUX 1, 2 & 3 OUTPUTS These outputs can be used to send the channel signal to an artist’s monitors (¼” Jacks) (headphones/in-ear/stage monitors), external FX or secondary PA/monitor system.

26 AUX CONTROLS The rotary controls set the output levels of the three Aux Outputs. The After & AFL SWITCHES Fade Listen (AFL) switches route their respective aux output signal to the monitor/

headphones outputs.

27 AUX 2 POST/PRE SWITCH This switch globally changes the AUX 2 feed on all the input modules to be either

post-fade or pre-fade.

28 STEREO INPUTS (¼” Jack) These two pairs of inputs can be used to connect line level stereo inputs from key-

29 2-TRACK IN (RCA Phono) You can connect the playback from your recording device here. 30 2-TRACK OUT Use these to control the 2 Track signal. The Monitor switch sends the signal to the

monitor outputs and phones, whilst the TO MIX switch sends it to the main mix.

31 Record Outputs (RCA Phono) You can connect these to the inputs of your recording device. 32 PHANTOM POWER Press this to globally switch the phantom power (48V) on for condenser microphones. WARNING: Do Not apply Phantom Power before connecting a micro-

phone.

Your MPMi console is equipped with a Kensington® Security slot on the rear panel for use with compatible PC/Laptop security cables. For more information about the Kensington range of security devices please visit http://us.kensington.com

15Soundcraft MFXi MPMi User Guide Issue 1210

WIRING UP

Mic Input

The MIC input accepts XLR-type connectors and is designed to suit a wide range of BALANCED or UNBALANCED low-level signals, whether from delicate vocals requiring the best low-noise performance, or drum kits needing maximum headroom. Professional dynamic, condenser or ribbon mics are best because these will be LOW IMPEDANCE. While you can use low-cost HIGH IMPEDANCE mics, you do not get the same degree of immunity to interference on the microphone cable and as a result the level of background noise may be higher. If you turn the PHANTOM POWER on, the socket provides a suitable powering voltage for professional condenser mics.

DO NOT use UNBALANCED sources with the phantom power

switched on. The voltage on pins 2 & 3 of the XLR connector may

cause serious damage. BALANCED dynamic mics may normally be

used with phantom power switched on (contact your microphone

manufacturer for guidance)

The input level is set using the input GAIN knob. The LINE input offers the same gain range as the MIC input, but at a higher input impedance, and is 15dB less sensitive. This is suitable for most line level sources.

WARNING !

Start with the input GAIN knob turned fully anticlockwise

when plugging high level sources into the LINE input to avoid

overloading the input channel or giving you a very loud surprise!

Line Input

Accepts 3-pole 6.35mm (1/4”) jacks, or 2-pole mono jacks which will automatically ground the ‘cold’ input. Use this input for sources other than mics, such as keyboards, drum machines, synths, tape machines or DI boxes. The input is BALANCED for low noise and immunity from interference, but you can use UNBALANCED sources by wiring up the jacks as shown, although you should then keep cable lengths as short as possible to minimise interference pick-up on the cable. Note that the ring must be grounded if the source is unbalanced. Set the input level using the GAIN knob, starting with the knob turned fully anticlockwise. Unplug any MIC connection when using the LINE input.

Insert Point

The unbalanced, pre-EQ insert point is a break in the channel signal path, allowing limiters, compressors, special EQ or other signal processing units to be added in the signal path. The Insert is a 3-pole 6.35mm (1/4”) jack socket which is normally bypassed. When a jack is inserted, the signal path is broken, just before the EQ section. The signal from the channel appears on the TIP of the plug and is returned on the RING, with the sleeve as a common ground. The Send may be tapped off as an alternative pre-fade, pre-EQ direct output if required, using a lead with tip and ring shorted together so that the signal path is not interrupted.

16 Soundcraft MFXi MPMi User Guide Issue 1210

+ 42 hidden pages