Martin M2GO HD
Martin M2PC
Safety and Installation Guide
Table of Contents
Dimensions
Introduction
................................................................................................................................... 3Technical Support
................................................................................................................................... 4Safety Information
................................................................................................................................... 5Included Items
................................................................................................................................... 6Software
................................................................................................................................... 7Recommended PC system for M2PC
Setup and Assembly
................................................................................................................................... 8Unpacking
................................................................................................................................... 8Placement
................................................................................................................................... 9Power Connections
Connections
................................................................................................................................... 10Right Side panel
................................................................................................................................... 11Rear panel
Service
......................................................................................1
......................................................................................2
......................................................................................8
......................................................................................10
......................................................................................12
Specifications
................................................................................................................................... 13M2GO HD
................................................................................................................................... 16M2PC
©2017 Martin Professional™ ApS. Information subject to change without notice. Martin Professional™ and all
affiliated companies disclaim liability for any injury, damage, direct or indirect loss, consequential or economic
loss or any other loss occasioned by the use of, inability to use or reliance on the information contained in this
document. Martin™, Harman™ and all other trademarks in this document pertaining to services or products by
Martin Professional™ or its affiliates and subsidiaries are registered as the property of Harman International
......................................................................................13
Industries.
Martin M2GO HD and M2PC Safety and Installation Guide
I © 2017 Martin Professional ApS
Dimensions
All dimensions are in millimeters
Martin M2GO HD and M2PC Safety and Installation Guide
1 © 2017 Martin Professional ApS
Introduction
Thank you for purchasing the Martin M2GO HD - M2PC Lighting Control System.
The system offers a powerful lighting controller with all the features of the M-Series of Martin controller
in a small and compact housing.
The M2GO HD is a complete lighting desk with an integrated processor, while the M2PC is a USB
control surface that requires an external PC system.
Both consoles are identical with the exception of the integrated screen, processor and the associated
connections on the back of the M2GO HD.
Please read this Safety and Installation Guide carefully. Visit the Martin website www.martin.com for
further documentation including the user manual for the software and access to our user forums.
Martin M2GO HD and M2PC Safety and Installation Guide
2 © 2017 Martin Professional ApS
Technical Support
Most information regarding the controller systems of Martin Professional can be found at www.martin.
com/controllersupport
Fixture Profiles
The software offers a fixture profile editor to create custom profiles. It is also possible to have Martin
Professional add a new profile to the standard library.
Profile requests can be made on our website
http://www.martin.com/controllersupport/fixture_libraries.html
Please check whether the profile is already available before filling out a request.
Support Email
For specific questions please contact us directly at controllersupport@martin.dk
Training Videos
A large number of training videos showing the operation of the software can be found on our youtube
channel.
http://www.youtube.com/martincontroller
Important! For certain support and warranty inquiries the user will need to provide the device
serial number. To see the serial number, disconnect the console from power and from all external
devices, lift it up carefully and turn it over.
Martin M2GO HD and M2PC Safety and Installation Guide
3 © 2017 Martin Professional ApS
Safety Information
This product is for professional use only. It is not for household use. It presents risks of lethal or
severe injury due to electric shock. Read this user manual before powering or installing the console ,
follow the safety precautions listed below and observe all warnings in this manual and printed on the
product.
If you have questions about how to operate the product safely, please contact your Martin supplier or
call the Martin 24-hour service hotline on +45 8740 0000, or in the USA on 888-832-4180.
This product is for indoor use ONLY.
Important! This is a product according to Class A. In a domestic environment this
product may cause radio interference in which case the user may be required to take
adequate measures.
Ensure that the power supply is electrically grounded (earthed) . Do not use ground lift
adapters.
Use only a source of AC power that complies with local building and electrical codes and has
both overload and ground-fault protection.
Use only the provided AC power supply and power cords and use the correct connector for the
country of operation. Use of the factory provided power cable is mandatory for operation in the
US and Canada.
Disconnect the product from power immediately if the power supply or cable or any cover or
component is wet or not in perfect condition. Do not reconnect to power until the damaged item
has been repaired or replaced.
Do not expose the product to rain or moisture.
Allow free unobstructed airflow to the bottom and back of the product. Do not block the
ventilation slots.
Operate the console only on a stable and solid surface.
Do not use the product if the ambient temperature exceeds 40°C (104° F)
Refer any service operation not described in this manual to a qualified technician.
Do not modify the product or install other than genuine Martin parts.
Transport the product only in suitable packaging or a custom fitted road case. Transportation
damage is not covered under warranty.
Protect the internal touch screen from sharp objects and operate the screen using a finger only.
Caution: Risk of fire and electrical shock. Use only in dry locations.
Caution: Risk of explosion if CMOS battery is replaced by an incorrect type. Dispose of used
batteries according to local environmental regulations
Caution: Do not expose CMOS battery to excessive heat such as sunshine or fire.
Martin M2GO HD and M2PC Safety and Installation Guide
4 © 2017 Martin Professional ApS
Included Items
Each package contains the following items:
M2GO HD or M2PC Controller
Dust cover for M2GO HD or protective cover for M2PC
External power supply unit with locking 4-pin XLR connector
LED desklamp
1.5 m (4.9 ft.) power cable, 3-pin IEC P/N 11501012 (for use outside the USA and Canada)
1.5 m (4.9 ft.) power cable, 3-pin IEC P/N 11501502 (with NEMA 15-5P plug for use within
the USA and Canada)
USB cable
Safety and Installation Manual
Martin M2GO HD and M2PC Safety and Installation Guide
5 © 2017 Martin Professional ApS
Software
The software for the M2GO HD and M2PC is available from the support website www.martin.com/
controllersupport
Please check periodically for new releases that may add new functionality or resolve a bug.
It is necessary to update to the latest release software before using the controller for the first
time.
Martin M2GO HD and M2PC Safety and Installation Guide
6 © 2017 Martin Professional ApS
Recommended PC system for M2PC
The M2PC is designed to be operated with an external PC system that utilizes a touch screen.
We strongly recommend that you do not use the M2PC without a touchscreen because the
controller software is designed around a touch interface.
Without the touchscreen the system will provide a poor user experience and is difficult to use.
The PC should meet these minimum recommendations:
Windows 10 Operating System
Intel Core i5 processor
USB 2.0 connection
4GB RAM
1280x800 resolution touchscreen
Martin M2GO HD and M2PC Safety and Installation Guide
7 © 2017 Martin Professional ApS
Setup and Assembly
Unpacking
Open the shipping box carefully and keep all included pieces and protective covers for re-use.
Do not transport the M2GO HD / M2PC in any other container than the factory-provided cardboard box
with the original protective packaging inserts or a professionally designed protective case.
The M2PC is provided with a protective clip-on cover. Remove the cover carefully before powering up
the system.
The cover can be conveniently placed underneath the console during operation.
The M2GO HD is provided with a dust cover.
Martin Professional offers a rugged road case for the M2GO HD console.
Placement
The controller requires a stable mounting position that provides support for all 4 rubber feet on the
bottom.
Never place the controller onto a blanket or other soft surface as this would block the ventilation
openings and cause overheating that would shut down the internal processor and possibly damage
the controller.
Martin M2GO HD and M2PC Safety and Installation Guide
8 © 2017 Martin Professional ApS
Power Connections
Wire color (standard EU code)
Pin
Symbol
brown
live
L
blue
neutral
N
yellow/green
ground
The Martin M2GO HD - M2PC accepts AC mains power at 100-240V 50/60Hz. Do not
connect it to power outside this range. Damage resulting from incorrect connection is not covered
under warranty.
North America: A cable with a NEMA 15-5P plug is provided for use with the M2GO - M2PC in the
USA and Canada. This approved cable must be used in North America.
Rest of the world: The provided IEC cable is not fitted with a country-specific plug.
Install only a plug that meets local and national electrical codes and is suitable for the country's
specific power outlet types. Refer to a certified electrician for any questions regarding a country's
specific requirements.
A 3-prong grounding-type (earthed type) plug must be installed following the plug manufacturer’s
instructions. The table below shows some possible pin identification schemes; if the pins are not
clearly identified, or if you have any doubts about proper installation, consult a qualified electrician.
To apply power to the product:
1. Check the power switch and ensure that it is set to the center OFF position.
2. Insert the 4-pin XLR connector from the external power supply unit into the power input on the
back of the desk.
3. Insert the provided power cable into the IEC connector of the power supply unit and connect the
cable to a properly protected and grounded power outlet.
4. M2PC: Connect the USB cable to the PC system
5. Turn on the desk by toggling the power switch to the CPU position (M2GO HD) or USB position
(M2PC)
Martin M2GO HD and M2PC Safety and Installation Guide
9 © 2017 Martin Professional ApS
Connections
Right Side panel
USB
The right side panel offers a USB device socket. This connector is ideally suited for USB flash drives
or a keyboard.
This connection is not suitable for boot operations (e.g. installation of an operating system). Use the
USB connectors on the back of the console for this purpose instead.
Do not exceed a current of 500 ma on any USB device port.
MIDI
The MIDI card provides MIDI In, Out and Thru 5-pin DIN connectors. The software supports incoming
MIDI Notes, MIDI Show Control and MIDI Timecode signals.
This card is optional on the M2PC controller.
SMPTE
The SMPTE device offers 3-pin XLR connectors for SMPTE In and Out signals.
This card is optional on the M2PC controller.
Martin M2GO HD and M2PC Safety and Installation Guide
10 © 2017 Martin Professional ApS
Rear panel
DC Power IN
4-pin XLR male
Desklight
3-pin XLR female, 12V, 500 ma for Littlite type gooseneck desklights
DMX 1-4
5-pin XLR female DMX Outputs, RDM compatible, bidirectional for DMX
Input
USB
4 x USB-A device connections (max. 500 ma)
1 x USB-B input connection
Network
RJ45 Gigabit Remote network connection
EtherDMX
RJ45 Gigabit DMX Ethernet connection
HDMI
2 x HDMI digital monitor connection
Line Out
Green 3.5 mm stereo jack
Line In
Blue 3.5 mm stereo jack
Mic In
Pink 3.5 mm mono jack
DC Power IN
4-pin XLR male
Desklight
3-pin XLR female, 12V, 500ma for Littlite type gooseneck desklights
DMX 1-4
5-pin XLR female DMX Outputs, RDM compatible, bidirectional for DMX
Input
USB
1x USB-B input connection
M2GO HD
M2PC
Martin M2GO HD and M2PC Safety and Installation Guide
11 © 2017 Martin Professional ApS
Service
The Martin M2GO HD - M2PC is designed as a rugged, roadworthy device. Occasional cleaning is the
only service required of the user. For any other service-related concerns, please contact your Martin
dealer or visit www.martin.com.
Any service not described in this document must be carried out by a qualified Martin technician.
The M2GO HD - M2PC requires periodic cleaning, as does any computer. The schedule depends
heavily on the operating environment; please consult a Martin service technician for recommendations
if needed.
As with any computer, never spray the cleaner directly onto the desk, always spray onto a lint-free
cloth and wipe clean. Cleaning products designed for cellphone and tablet devices tend to work very
well for cleaning a lighting console.
cause overheating and damage to the controller that is not covered by the warranty.
Important! Excessive dust, dirt smoke fluid build-up etc. can degrade performance and
Martin M2GO HD and M2PC Safety and Installation Guide
12 © 2017 Martin Professional ApS
Specifications
M2GO HD
High-resolution folding capacitive multi-touchscreen
Integrated Industrial high-speed processing
3.5” touchscreen for fast and direct parameter access
8 digital encoders for parameter control
8 customizable function keys
4 DMX universes direct from the console; up to 20 universes via Artnet and sACN without
external processors
Controls up to 10240 parameters
Built-in 2D visualizer for selection and real-time visualization
Customizable Graphical User Interface with context-sensitive toolbars and integrated Help
menu
Powerful effects engine
1000 cuelists with fader control
1000 cuelists with playback control buttons
Parallel execution of multiple cuelists
Submaster, Groupmaster and Override functionality
Parameter and Time-fanning functionality
Auto update for presets and cues
On-the-fly global timing adjustments
M-Series Manager Software for programming and triggering via time and calendar schedules,
RS232 and IP triggers
Multiple wing attachment (M-Series Modules)
MaxNet synchronized programming and playback support
Physical
Length: 300 mm (11.9 in.)
Width: 540 mm (21.3 in.)
Height: 99 mm (3.9 in.)
Weight: 9 kg (19.8 lbs.)
Martin M2GO HD and M2PC Safety and Installation Guide
13 © 2017 Martin Professional ApS
Control and Programming
Protocol: DMX512A (RDM), Artnet2, sACN
4 physical DMX ports
20 DMX universes integrated
No limit to number of DMX channels per fixture
Extensive fixture library for all known manufacturers
65000 presets for each group of functions (P/T, color, gobo, etc.)
Effect generator for automated programming of complex effects
Customizable highlight and lowlight function to identify individual fixtures
Relative or absolute programming
Fan function for all channels (including timing parameters)
On-the-fly global timing changes
Virtual cuelists
Macros
Wait, follow and link cues
HTP, LTP, chase, timecode, submaster and group master playback functionality Individual parameter
timings
Intuitive patch feature
Fixture type cloning
All channels with 16-bit resolution
Control/User Interface
Main playback interface: ten 60 mm playback faders, each with four function- assignable buttons
Eight customizable multi-function keys
Playback Select button
Master Go section with Go, Pause, Snap and Release
Four digital rotary encoders with push function and status
LED for fixture parameter control
3.5” touchscreen for parameter groups, effect parameters, fanning and global timings and button
Built-in 2D visualizer for selection and real-time visualization
Grand master rotary fader
Blind/preview button
Customizable highlight/lowlight function
Customizable parameter defaults
Next/last fixtures/groups
Large command keys
Playback
Assign a cue, cuelist or effect to any playback fader 500 playback banks, each containing 10
playbacks
100 pages of 100 playbacks activated by touchscreen button
No limit to cues per cuelist
Full 16-bit fading for high-resolution fixtures Individual fade in/fade out times for all playbacks
Manual override available at all times
Live 0-1000% override of global cue timings
Live programmer timing (“Sneak”)
Cuelists can be executed in tracking or non-tracking mode
Martin M2GO HD and M2PC Safety and Installation Guide
14 © 2017 Martin Professional ApS
Connections
4 x DMX universe outputs: 5-pin locking XLR
External monitor screen: VGA and HDMI
Artnet/sACN for up to 20 DMX universes in total: Gigabit RJ-45
MaxNet controller link: Gigabit RJ-45
Storage media/hardware peripherals: USB 3.0
Built-in Internal MIDI In/Out/Thru (MIDI show control, MIDI notes, MIDI timecode)
Built-in Internal SMPTE Timecode In/Out: 3-pin XLR
12 VDC power supply input: 4-pin XLR
Desk lamp (dimmable): 3-pin XLR
USB (storage media/hardware peripherals)
Back of console: 4 x USB 3.0
Side of console: 1 x USB 2.0
Electrical:
AC mains power to 12 V DC external PSU (included): 100-240 V nominal, 50/60 Hz, 12 V DC output:
5 A, 60 W max.
M2GO HD Power Input: 12 V DC, 53 W (max), 4.2 A (max)
Lamp Output: 12 V PWM, 0.5 A (max), 6 W (max)
Hardware
Industrial 15.6 inch TFT 16:9 touchscreen (1376x768 pixels)
Industrial 3.5" RGB touchscreen
SSD storage drive
Industrial motherboard with quad-core processor
8 GB RAM
Integrated graphics processor
Included Items
1.5 m (4.9 ft.) power cable, EU (Schuko), 3-pin IEC
1.5 m (4.9 ft.) power cable, US, 3-pin IEC
12 V DC 5 A external PSU
LED desk lamp, 6 W
Protective Cover
Martin™ One-Key: ShowDesigner 6™ Lite 3D Visualizer 1 year license, M-PC Pro with 64 universe
License
Accessories
Flightcase for M2GO HD Console: P/N 91535085
Martin™ M-Play: P/N 90737030
Martin™ M-DMX Interface Box / Martin™ M-PC 2U package: P/N 90737070
Ordering Information
Martin™ M2GO HD Console: P/N 90737080
Martin M2GO HD and M2PC Safety and Installation Guide
15 © 2017 Martin Professional ApS
M2PC
3.5” touchscreen for fast and direct parameter access
4 digital encoders for parameter control
8 customizable function keys
4 DMX universes direct from the console; up to 64 universes via Artnet and sACN with
external processors
Built-in 2D visualizer for selection and real-time visualization
Customizable Graphical User Interface with context-sensitive toolbars and integrated Help
menu
Powerful effects engine
1000 cuelists with fader control
1000 cuelists with playback control buttons
Parallel execution of multiple cuelists
Submaster, Groupmaster and Override functionality
Parameter and Time-fanning functionality
Auto update for presets and cues
On-the-fly global timing adjustments
M-Series Manager Software for programming and triggering via time and calendar
schedules, RS232 and IP triggers
MaxNet synchronized programming and playback support
Physical
Length: 300 mm (11.9in.)
Width: 540 mm (21.3 in.)
Height with dust cover installed: 99 mm (3.9 in.)
Weight: 4.6 kg (10.2 lbs.)
Martin M2GO HD and M2PC Safety and Installation Guide
16 © 2017 Martin Professional ApS
Control and Programming
Protocol: DMX512A (RDM), Artnet2, sACN
4 physical DMX ports
64 DMX universes integrated
No limit to number of DMX channels per fixture
Extensive fixture library for all known manufacturers
65000 presets for each group of functions (P/T, color, gobo, etc.)
Effect generator for automated programming of complex effects
Customizable highlight and lowlight function to identify individual fixtures
Relative or absolute programming
Fan function for all channels (including timing parameters)
On-the-fly global timing changes
Virtual cuelists
Macros
Wait, follow and link cues
HTP, LTP, chase, timecode, submaster and group master playback functionality Individual parameter
timings
Intuitive patch feature
Fixture type cloning
All channels with 16-bit resolution
Control/User Interface
Main playback interface: ten 60 mm playback faders, each with four function- assignable buttons
Eight customizable multi-function keys
Playback Select button
Master Go section with Go, Pause, Snap and Release
Four digital rotary encoders with push function and status
LED for fixture parameter control
3.5” touchscreen for parameter groups, effect parameters, fanning and global timings and button
Built-in 2D visualizer for selection and real-time visualization
Grand master rotary fader
Blind/preview button
Customizable highlight/lowlight function
Customizable parameter defaults
Next/last fixtures/groups
Large command keys
Playback
Assign a cue, cuelist or effect to any playback fader 500 playback banks, each containing 10
playbacks
100 pages of 100 playbacks activated by touchscreen button
No limit to cues per cuelist
Full 16-bit fading for high-resolution fixtures Individual fade in/fade out times for all playbacks
Manual override available at all times
Live 0-1000% override of global cue timings
Live programmer timing (“Sneak”)
Cuelists can be executed in tracking or non-tracking mode
Martin M2GO HD and M2PC Safety and Installation Guide
17 © 2017 Martin Professional ApS
Connections
4 x DMX universe outputs: 5-pin locking XLR
1 x storage media/hardware peripherals: USB 2.0
Ready to receive internal MIDI module and SMPTE Timecode module
Internal MIDI In/Out/Thru (MIDI Show Control, MIDI Notes, MIDI Timecode (optional)
Internal SMPTE Timecode In/Out: 3-pin XLR (optional)
12 VDC power supply input: 4-pin XLR
Desk lamp (dimmable): 3-pin XLR
Electrical:
AC mains power to 12 V DC external PSU (included): 100-240 V nominal, 50/60 Hz, 12 V DC output:
5 A, 60 W max.
M2PC Power Input: 12V DC, 18W (max), 1.5A (max)
Lamp Output: 12 V PWM, 0.5 A (max), 6 W (max)
Hardware
Industrial 3.5" RGB touchscreen
Included Items
1.5 m (4.9 ft.) power cable, EU (Schuko), 3-pin IEC
1.5 m (4.9 ft.) power cable, US, 3-pin IEC
12 VDC, 5 A external PSU
LED desk lamp with angular plug
Protective Cover
Martin™ One-Key: ShowDesigner 6™ Lite 3D Visualizer 1 year license, M-PC Pro with 64 universe
License
Accessories
Martin™ M-Play: P/N 90737030
Martin™ M-DMX Interface Box / Martin™ M-PC 2U package: P/N 90737070
Ordering Information
Martin™ M2PC™ Console P/N 90737010
Optional Midi PCB P/N 91613038
Optional SMPTE Timecode PCB P/N 90703040
Martin M2GO HD and M2PC Safety and Installation Guide
18 © 2017 Martin Professional ApS
Loading...