Harken Performa 46.2 PTP, Performa 46.2 STP, Performa 46.2 STQP Installation And Maintenance Manual
Installation and Maintenance Manual
MRPW-03
Performa
™
Winch 46.2 PTP
Index
Introduction 3
Technical characteristics 3
Weight 3
Maximum working load 3
Outline 3
Installation 4
Installation procedure 5
Maintenance 7
Washing 7
Maintenance table 7
Disassembly procedure 8
Exploded view with maintenance products 11
Assembly 12
®
Harken
Ordering spare parts 12
Exploded view 14
Parts list 16
limited worldwide warranty 12
Performa™ Winch
46.2 PTP
2
Installation and Maintenance Manual
Introduction - Technical characteristics - Outline
Introduction
This manual gives technical information on winch installation and maintenance, including
disassembling and reassembling.
This information is DESTINED EXCLUSIVELY for specialised personnel or expert users.
Installation, disassembling and reassembling of the winch by personnel who are not experts may
cause serious damage to users and those in the vicinity of the winch.
Harken
In case of doubt the Harken
This Manual is available only in English. If you do not fully understand the English language, do
not carry out the operations described in this Manual.
Technical characteristics
®
accepts no responsibility for defective installation or reassembly of its winches.
®
Tech Service is at your disposal at techservice@harken.it
Power ratio Gear ratio
1st speed
2nd speed
The theoretical power ratio does not take friction into account.
11,70 : 1 2,30 : 1
46,50 : 1 9,17 : 1
Weights
PT version
Weight (Kg)
Maximum working load
WARNING!
The maximum working load (MWL) for the 46.2 PT Performa™ Winch is 1300 Kg (2866 lb)
Subjecting the winch to loads above the maximum working load can cause the winch to fail or
pull off the deck suddenly and unexpectedly during high loads causing severe injury or death.
5,1
Outline
Performa™ Winch
46.2 PTP
Ø101
Ø184
181
90
Line entry height
3
Installation and Maintenance Manual
Installation
Installation
The winch must be installed on a fl at area of the deck, reinforced if necessary to bear a load equal
to at least twice the maximum working load of the winch.
It is the installer's responsibility to carry out all structural tests needed to ensure that the deck can
bear the load.
Harken® does not supply the screws needed to install the winch since these may vary depending on
the deck on which it is to be installed. It is the installer's responsibility to choose the correct screws
taking account of the loads they will have to bear. Harken® assumes no responsibility for incorrect
installation of its winches or for an incorrect choice of mounting screws.
DANGER!
Incorrect installation of the winch may cause severe injury or
death. Consult the yard that built the boat in the case of doubt
over the correct positioning of the winch.
WARNING!
Failure to use the correct number and type of mounting fasteners
or failure to ensure the correct deck strength can result in the
winch pulling off the deck suddenly and unexpectedly during
high loads causing severe injury or death.
WARNING!
Verify the entry angle of the sheet. This must be 8° with tolerance
of ±2°, to avoid sheet overrides and damaging the winch or
making the winch inoperable leading to loss of control of the boat
which can lead to severe injury or death.
WARNING!
Mount the winch on the deck so that the drive gear is positioned
where the sheet enters the winch drum.
Incorrect position of drive gear can weaken winch leading to failure
which can cause an accident leading to severe injury or death.
8°
drive gear
SHEET
Once you have chosen the correct mounting position for the winch on the deck proceed with
installation.
Performa™ Winch
46.2 PTP
4
Installation and Maintenance Manual
Procedure
To install the winch you must remove the drum and use Socket Head (SH) bolts.
Tools needed
One medium fl at-bladed screwdriver
To identify the various parts, refer to the exploded view at the end of this Manual.
Torque to apply when assembling
1. Unscrew the central screw ( 2Nm/18 in-lb)
3. Lift off the drum n°22
2. Slide off the hub n°27 and the cover n°26
and the washer n°30
Install the winch on the deck in the position you have chosen, keeping in mind the limits described
on page 3. (See paragraph on installation)
Performa™ Winch
46.2 PTP
5
Installation and Maintenance Manual
Loading...