Harken Performa 70.2 STP, Performa 40.2 STP, Performa 40.2 STQP Installation And Maintenance Manual

Installation and Maintenance Manual

MRPW-03

Performa

™

Winch 70.2 STP

Index

Introduction 3

Technical characteristics 3

Weight 3
Maximum working load 3

Outline 3

Installation 4

Installation procedure 7
Positioning the self-tailing arm 8

Maintenance 8

Washing 8
Maintenance table 8
Disassembly procedure 8
Exploded view with maintenance products 12
Assembly 13

®

Harken

Ordering spare parts 14

Exploded view 15

Parts list 17

limited worldwide warranty 14

Performa™ Winch

70.2 STP

2

Installation and Maintenance Manual

Introduction - Technical characteristics - Outline

Introduction

This manual gives technical information on winch installation and maintenance, including
disassembling and reassembling.
This information is DESTINED EXCLUSIVELY for specialised personnel or expert users.
Installation, disassembling and reassembling of the winch by personnel who are not experts may
cause serious damage to users and those in the vicinity of the winch.
Harken
In case of doubt the Harken
This Manual is available only in English. If you do not fully understand the English language, do
not carry out the operations described in this Manual.

Technical characteristics

®

accepts no responsibility for defective installation or reassembly of its winches.

®

Tech Service is at your disposal at [e-mail]

Power ratio Gear ratio

1st speed

2nd speed

22,20 : 1 5,70 : 1

72,00 : 1 18,50 : 1

The theoretical power ratio does not take friction into account.

Weight

ST Version

Weight (Kg)

11,3

Maximum working load

WARNING!

The maximum working load (MWL) for the 70.2 ST Performa™ Winch is 2700Kg (5952 lb)
Subjecting the winch to loads above the maximum working load can cause the winch to fail or

pull off the deck suddenly and unexpectedly during high loads causing severe injury or death.

Outline

Performa™ Winch

70.2 STP

Ø130

Ø240

257

115

Line entry height

3

Installation and Maintenance Manual

Installation

Installation

The winch must be installed on a at area of the deck, reinforced if necessary to bear a load equal
to at least twice the maximum working load of the winch.
It is the installer's responsibility to carry out all structural tests needed to ensure that the deck can
bear the load.
Harken® does not supply the screws needed to install the winch since these may vary depending
on the deck on which it is to be installed.
It is the installer's responsibility to choose the correct screws taking account of the loads they will
have to bear.
Harken® assumes no responsibility for incorrect installation of its winches or for an incorrect choice
of mounting screws.

DANGER!

Incorrect installation of the winch may cause severe injury or
death. Consult the yard that built the boat in the case of doubt
over the correct positioning of the winch.

WARNING!

Failure to use the correct number and type of mounting fasteners
or failure to ensure the correct deck strength can result in the
winch pulling off the deck suddenly and unexpectedly during
high loads causing severe injury or death.

WARNING!

Verify the entry angle of the sheet. This must be 8° with tolerance
of ±2°, to avoid sheet overrides and damaging the winch or
making the winch inoperable leading to loss of control of the boat
which can lead to severe injury or death.

WARNING!

Mount the winch on the deck so that the drive gear is positioned
where the sheet enters the winch drum.
Incorrect position of drive gear can weaken winch leading to failure
which can cause an accident leading to severe injury or death.

8°

drive gear

SHEET

Once you have chosen the correct mounting position for the winch on the deck proceed with
installation.

Performa™ Winch

70.2 STP

4

Installation and Maintenance Manual

Procedure

To install the winch you must remove the drum and use Socket Head (SH) bolts or Hexagonal
Head (HH) bolts.

Tools needed

One medium at-bladed screwdriver

To identify the various parts, refer to the exploded view at the end of this Manual.

Torque to apply when assembling

Follow steps below only to install the winch using Socket Head (SH) bolts

1. Unscrew the central screw ( 2Nm/18 in-lb)

3. Unscrew the three screws n°26
4Nm/35 in-lb)

(

2. Slide off the assy socket n°28 and the
cover n°27

4. Remove the stripper arm n°25
by rotating and lifting it.

5. Lift off the drum n°23

Performa™ Winch

70.2 STP

Install the winch on the deck in the
position you have chosen, keeping in
mind the limits described on page 3.
(See paragraph on installation)

5

Installation and Maintenance Manual

Follow steps below only to install the winch using hexagonal headed bolts

6. Completely unscrew the three screws n° 26

8. Slide out the central shaft n°19

7. Remove the stripper arm housing n°21

9. Unscrew the 6 hex screws n°17

20Nm/177 in-lb)

(

10. Remove the assy housing n°16

Performa™ Winch

70.2 STP

Install the winch on the deck in the
position you have chosen, keeping in
mind the limits described on page 3.

6

Installation and Maintenance Manual

Installation procedure

Carry out the Procedure, then install the winch on the deck in the chosen position.

A. Position the base of the winch on the deck and mark the position of the holes or use the drilling

cut-out template at the point where you have decided to place the winch.

Below is a reduced scale diagram.

The drilling cut out template is available on the Harken® website, www.harken.com

54°

60°

41°

64°

final pinion
position

28°

Ø8.5

n°6

Winch outside Ø240

60°

Ø205

B. Remove the winch and drill the six 8.5 mm diameter holes.

C. Bolt the base of the winch to the deck using ve M8 bolts (not supplied by Harken®), correctly

chosen for the thickness and type of the boat deck. Consult the yard that built the boat in case of
doubt.

WARNING!

To install the winch on the deck, use only bolts in A4 stainless steel (DIN 267 part11).
Bolts made of other materials may not have sufficient strength or may corrode which can
result in winch pulling off deck suddenly and unexpectedly during high loads causing
severe injury or death.

54°

NOTICE

To mount winches on the deck, do not use countersunk bolts.

D. Fill the mounting holes with a suitable marine sealant.

E. Remove the excess adhesive/sealant from the holes and base drainage channels

Performa™ Winch

70.2 STP

7

Installation and Maintenance Manual

Maintenance

F. Reassemble the winch following the steps of the Procedure in the reverse order, and apply the
products indicated in the section on maintenance.

NOTICE

Before closing the winch, make sure the holes and drainage channels in the base of the winch
are not obstructed.

Positioning the self-tailing arm

Position the self-tailing arm so that the line leaving the winch is led into the cockpit.

Maintenance

Washing

Winches must be washed frequently with fresh water, and in any case after each use.
Do not allow teak cleaning products or other cleaners containing caustic solutions to come into
contact with winches and especially anodised, chrome plated or plastic parts.
Do not use solvents, polishes or abrasive pastes on the logos, on the stickers on the winches or on
any anodized, chrome plated and plastic surfaces.
Make sure that the holes and drainage channels in the base of the winch are not obstructed so that
water does not collect.

Maintenance table

Winches must be visually inspected at the beginning and end of every season of sailing or racing.
In addition they must be completely overhauled, cleaned and lubricated at least every 12 months.
After an inspection, replace worn or damaged components. Do not replace or modify any part of the
winch with a part that is not original.

WARNING!

Periodic maintenance must be carried out regularly. Lack of adequate maintenance shortens
the life of the winch, can cause serious injury and also invalidate the winch warranty.
Installation and maintenance of winches must be carried out exclusively by specialized
personnel.

®

In the case of doubt contact Harken

Disassembly procedure

Tools needed

One medium at-bladed screwdriver
A number ve hex key
Rags

Tech Service at [e-mail]

Torque to be applied in assembly phase

Performa™ Winch

70.2 STP

8

Installation and Maintenance Manual

To identify the various parts refer to the exploded view at the end of this Manual.

Carry out procedure as shown in the paragraph on winch installation and then do the following:

6. Completely unscrew the three screws n° 26

8. Slide out the central shaft n°19

7. Remove the stripper arm housing n°21

9. Unscrew the 6 hex screws n°17
(

20Nm/177 in-lb)

10. Remove the assy housing n°16

Performa™ Winch

70.2 STP

11. Remove the gear n°6, pawls n°3

and the washer n°7

9

Installation and Maintenance Manual

12. Remove gear n°2.

13. Remove the idler and pinion n°14.

14. Remove roller bearings n°15

16. Remove gear n°10

15. Remove pawls n°11.

17. Remove roller bearings n°12.

Performa™ Winch

70.2 STP

10

Installation and Maintenance Manual

If it is necessary to replace any jaws of the winch, proceed as follows:

I. Unscrew the 4 screws n°24

4Nm/35 in-lb)

(

Inspect balls inside the drum and carefully check the correct position; if it is necessary to put back
any balls, push balls in the race (as shown below):

Once the winch is completely disassembled, clean the parts: use a basin of diesel oil to soak
metal components and rinse plastic parts in fresh water. Once you have done this, dry the parts
with cloths that do not leave residue.

II. Remove the jaws n°22

Inspect gears, bearings, pins and pawls for any signs of wear or corrosion.

Carefully check the teeth of gears and ring gears to make sure there are no traces of wear.

Check the roller bearings and check there are no breaks in the bearing cages.
Replace worn or damaged components.

Carry out maintenance on components using the products listed below.
For more information on which products to use where, refer to the exploded diagram below.

Use a brush to lightly lubricate all gears, gear pins, teeth and all moving parts with grease.
Lightly lubricate the pawls and springs with oil. Do not use grease on the pawls!

Performa™ Winch

70.2 STP

11

Installation and Maintenance Manual

Exploded view with maintenance products

1

G

G

A

A

Anti-seize

A

Harken® Grease

G

Harken® Pawl Oil

O

G

A

G

O

G

A

G

G

G

G

G

G

O

G

Performa™ Winch

70.2 STP

1

Apply Harken® grease on assy socket screw

12

Installation and Maintenance Manual

Assembly

Make sure that the holes and drainage channels in the base of the winch are not obstructed
Assemble the winch in the reverse order of the sequence in the section on disassembly.

To tighten bolts, use the torque indicated in the disassembly procedure.

IWhen positioning the stripper arm,
align the peeler with it.

If the jaws have been disassembled,
insert peeler between the two jaws,
taking care that the letters TOP on the
peeler are facing upwards.

OIL

In case of doubt concerning the assembly procedure contact Harken

The icon on the Stripper Arm Housing
indicates the Stripper Arm nal position.

Change the Stripper Arm Housing
angle to modify the Stripper Arm nal

position.

To assemble the pawls:

correctly position the spring in its housing as
shown at left. Hold the spring closed and slide
the pawl into its housing. Once in position,
check that the pawls can be easily opened and
closed with a nger.

®

Tech Service: [e-mail]

Performa™ Winch

70.2 STP

13

Installation and Maintenance Manual

Harken® limited worldwide warranty - Ordering spare parts

Harken® limited worldwide warranty

Refer to the Harken® Limited Worldwide Warranty in the Harken® Catalogue and on the website
www.harken.com

Ordering spare parts

Spare parts can be requested from Harken® as
described in the Harken
Warranty, indicating the part number in the
Parts List and including the serial number of
the winch for which the parts are required.

The serial number of the winch is printed on
a plate on the drum support of the winch.

Manufacturer

®

Limited Worldwide

Harken® Italy S.p.A.

Via Marco Biagi, 14
22070 Limido Comasco (CO) Italy
Tel: [phone]
Fax: [phone]
Email: [e-mail]
Web: www.harken.com

W XXXXX
XXXXXXXXX

Tech Service
Email: [e-mail]

Customer Service

Tel: [phone]
Email: [e-mail]

Headquarters

Harken®, Inc.

1251 East Wisconsin Avenue
Pewaukee, Wisconsin 53072-3755 USA
Tel: [phone]
Fax: [phone]
Email: [e-mail]
Web: www.harken.com

Performa™ Winch

70.2 STP

Tech Service
Email: [e-mail]

Customer Service

Tel: [phone]
Email: [e-mail]

14

Installation and Maintenance Manual

Exploded view 1/2

23

20

18

16

17

28

27

26

25

21

24

22

Performa™ Winch

70.2 STP

15

Installation and Maintenance Manual

Exploded view 2/2

19

7

6

4

5

3

2

1

9

13 12

1115

14 5

4

10

8

Performa™ Winch

70.2 STP

16

Installation and Maintenance Manual

Parts list

Performa Winch 70.2 STP

Pos Q.ty Code Description

1 1

2 1 S414770004 Gear Z13 W70
3 1 S413030004 Pawls Carrier Ø8xN2
4 6 S000090004 Pawl Ø8*
5 6 S000380001 Pawl Spring Ø8*
6 1 S414390041 Ratchet Gear Z21xN2
7 1 S413120002 Washer Ø22.5xØ45x1
8 1 S278170002 Washer Ø12.5xØ48x1.5

9 1 S281010004 Pin for gear
10 1 S414420041 Ratchet Gear Z26xN4
11 1 S414410004 Pawls Carrier Gear Z13 N4
12 2 A72821800 Roller Bearing Ø14xØ20x18
13 1 S416030004 Gear Pin Ø12xØ18x52,5
14 1 S414760004 Idler and Pinion Z26/Z13 W70
15 2 A74162300 Roller bearing Ø24xØ18x18
16 1

A96636900

1

S476030004

1

S4152300A7

2

S415580085

A94146800

2

S415580085

1

S4130900A7

Performa base assembly Winch 70

Performa base Winch 70
Heli-coil M8x10
Centering bushing Ø12
Bushing Ø22xØ25x9.5
Bushing Ø12xØ35x9
Winch Product Sticker**

Assy Housing WInch 70

Housing W70
Heli-coil M6x9
Support Bushing W70
Bushing Ø12xØ35x9
Bushing Ø22xØ25x8.5

Pos Q.ty Code Description

17 6 M0606303 Screw M8x25 UNI 5931
18 3 A74147500 Roller Bearing Ø102xØ114x26
19 11A94147900

S413880002
20 Winch Serial Number Sticker
21 1 S4144300A0 Stripper Arm Housing W60/70
22 1

23 150A96637000

24 4 M0601803 Screw UNI EN ISO 1207:1996 - M6x35 - A4
25 1 S663710019 PERFORMA Black Stripper Arm W70
26 3 M0601903 Screw M6x16 UNI1207
27 1 S4160400B1 Cover 2 Speed W70
28 1

A96637200

1

S414850080

4

S683520001

M0610280

A94136400

1

S415130085

1

M0614303

Assy Shaft Winch 70

Central shaft W70 ST
Washer Ø17.2xØ32x1.5

PERFORMA Assy Jaws W70

Lower Jaw W70
Upper Jaw W70
Peeler W60 - 70
Ø7-Ø1-L30mm Spring

Spare kit drum Winch 70 Performa

PERFORMA Assy Drum Winch 70
Ball 5/16"

Assembly Socket W20-80

Socket Handle W20/80
Washer Ø7.7xØ25x5.8
Screw M8x20 UNI 6109

*Available with service kit; see website www.harken.com

**Winch product sticker

Performa™ Winch

70.2 STP

17

Installation and Maintenance Manual