Hark HK3797 Owner's Manual

Owner’s Manual

ASSEMBLY, CARE & SAFETY INSTRUCTIONS

Item No. HK3797

4 BURNER BBQ

WITH SIDE BURNER

4 Burner BBQ with Side Burner

Warranty Details

The product is guaranteed to be free from defects in workmanship and parts for a period

of 12 months from the date of purchase. Defects that occur within this warranty period,

under normal use and care, will be repaired, replaced or refunded at our discretion. The

benets conferred by this warranty are in addition to all rights and remedies in respect of

the product that the consumer has under the Competition and Consumer Act 2010 and

similar state and territory laws.

Our goods come with guarantees that cannot be excluded under the Australian Consumer

Law. You are entitled to a replacement or refund for a major failure and for compensation

for any other reasonably foreseeable loss or damage. You are also entitled to have the

goods repaired or replaced if the goods fail to be of acceptable quality and the failure does

not amount to a major failure.

After Sales Support

Telephone: [phone]
[phone]
Email: [e-mail]

YEAR

WARRANTY

3

Model No.: HK3797
Product Name: 4 BURNER BBQ WITH SIDE BURNER - For propane (LPG) use only

FOR OUTDOOR USE ONLY. PLEASE READ INSTRUCTIONS CAREFULLY BEFORE
ASSEMBLING. RETAIN THIS MANUAL FOR FUTURE REFERENCE.

FOR YOUR SAFETY

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open ame.

3. Open BBQ hood.

4. If odour continues, immediately call your

gas supplier or your local re department.

PRECAUTIONS

1. Leak test all connections after each tank rell.

2. Never check for leaks with a match or open

ame.

3. Do not store or use gasoline or other

ammable vapours and liquids in the vicinity

of this appliance.

4. The BBQ must not be installed under or on
any combustible material. Minimum clearance
from any combustible materials of ALL sides
of the BBQ is 600mm and 1000mm overhead.

HAZARDOUS FIRE OR EXPLOSION MAY RESULT
IF INSTRUCTIONS ARE IGNORED.

It is the consumer's responsibility to see that the BBQ is properly
assembled, installed, and taken care of. Failure to follow instructions in
this manual could result in injury and/or property damage.

Dimensions 132(W) 56(D) 118.5(H) cm

4

PAR T DESCRIPTION

A BBQ BODY AND HOOD

B RIGHT HAND SIDE SHELF WITH BURNER

C LEFT HAND SIDE SHELF

D RIGHT HAND END PANEL

E LEFT HAND END PANEL

F BASE PANEL

G LEFT HAND DOOR

H RIGHT HAND DOOR

I CABINET BACK PANEL

J DRIP TRAY

K WARMING RACK

L CAST IRON GRILL

M CAST IRON HOT PLATE

N CABINET TOP RAIL

O BACK RIGHT HAND LEG

P FRONT RIGHT HAND LEG

Q FRONT LEFT HAND LEG

EXPANDED VIEW

PART LIST

PAR T DESCRIPTION

R BACK LEFT HAND LEG

S DOOR HANDLE X 2PCS

T SIDE BURNER TRIVET

U CONDIMENT RACK

V GREASE PAN

W GREASE PAN HOLDER

X CONTROL KNOB - SIDE BURNER

Y PAPER TOWEL HOLDER

Z FLAME TAMER X 2PCS

AB SIDE BURNER

AC LEFT HAND DRIP TRAY RAIL

AD RIGHT HAND DRIP TRAY RAIL

AE LOCKING CASTOR X 2PCS

AF CASTOR X 2PCS

AG CABINET SPACER RAIL

AH CABINET DOOR STOP

AI HOSE AND REGULATOR

AI

5

PLEASE NOTE THERE ARE ALSO PRE-ASSEMBLED SCREWS ATTACHED TO PARTS

PLEASE FOLLOW INSTRUCTIONS TO IDENTIFY WHAT SCREWS ARE NEEDED

INSTRUCTIONS FOR YOUR NEW BBQ

Tools needed for assembly

Phillips Head Screwdriver (not included)

Before assembly

Please read all instructions thoroughly before proceeding.

Find a large, clean area in which to assemble your BBQ. Please refer to the parts list and

assembly diagram as necessary.

Ensure any transit protection or packaging is removed.

Do not throw out any packaging until BBQ is fully assembled incase parts are still enclosed.

HARDWARE PACK

1/4" SCREW

M6 WASHERS

5/32" SCREW

M4 WASHERS

6

A. ASSEMBLY OF THE BBQ

STEP 1 ATTACH BBQ LEGS TO RIGHT HAND END PANEL

Parts Required

D Right hand end panel

O Back right hand leg

P Front right hand leg

STEP 2 ATTACH BBQ LEGS TO LEFT HAND END PANEL

Parts Required

E Left hand end panel

Q Front left hand leg

R Back left hand leg

— 3pcs screws are pre-assembled on each leg and they

should be screwed out 2-3mm for assembly.

— Align right hand end panel onto screws and tighten as

per figure 1.

— 3pcs screws are pre-assembled on each leg and they

should be screwed out 2-3mm for assembly.

— Align left hand end panel onto screws and tighten as

per figure 2.

RIGHT HAND END PANEL (D)

BACK RIGHT HAND LEG (O)

Figure 1

FRONT RIGHT HAND LEG (P)

Figure 2

BACK LEFT HAND LEG (R)

FRONT LEFT HAND LEG (Q)

LEFT HAND END PANEL (E)

7

STEP 4 FITTING CABINET CASTORS

STEP 3 FITTING CABINET BASE TO LEFT HAND AND RIGHT HAND END

PANEL

Parts Required

AE 2pcs Locking castors

AF 2pcs castors

Parts Required

F Base panel

— Screw locking castors into bottom of left hand legs.

— Screw castors into bottom of right hand legs.

— 8pcs screws are pre-assembled and they should be

screwed out 2-3mm for assembly.

— Once legs are located onto screws, tighten the screws.

This is done through the hole on the legs as per figure 3.

— Please note the hole in the base panel should be

closest to the right hand end panel.

Figure 3

Figure 4

LEFT HAND END PANEL (E)

BASE PANEL (F)

RIGHT HAND END PANEL (D)

HOLE

SCREW LOCKING CASTORS

(AE) IN TO BOTTOM OF

LEFT HAND END LEGS.

SCREW CASTORS (AF)

IN TO RIGHT HAND

END LEGS

.

8

STEP 5 FITTING CABINET TOP RAIL

STEP 6 FITTING CABINET BACK PANEL

Parts Required

N Cabinet top rail

Parts Required

I Cabinet back panel

— 4pcs screws are pre-assembled in BBQ legs and they

should be screwed out 2-3mm for assembly as per figure 5.

— Align cabinet top rail on these screws and tighten as per

figure 6.

— 7pcs screws are pre-assembled and they should be

screwed out 2-3mm for assembly.

— Align cabinet back panel onto the screws and tighten as

per figure 7.

Figure 7

Figure 5

Figure 6

CABINET TOP RAIL (N)

CABINET BACK PANEL (I)