Scan to watch the installation video
http://delivr.com/2QRX9
Vanity Base Pullout
Installation Instructions
IMPORTANT:
Before you begin, make sure you familiarize yourself with all the
parts and fully read the instructions.
CUSTOMER SERVICE:
Toll-free customer help line available weekdays between
7:00am and 6:00pm Central Time at 800-463-0660.
TOOLS NECESSARY:
Screw gun or Phillips screwdriver and tape measure. NOTE: If
screw gun has a clutch, set to lowest setting so as not to over
tighten and/or strip screws.
PARTS IDENTIFICATION:
D
for the VBPO8-SC
Bottom Measurements
NOTE: Illustrations for measurement only.
1.25”
2.5”
14.6”
2”
STEP 1 - Install Base
Pull out
Front plywood runner
B
C
A
A Mounting Base 1 pcs
B Base Pullout Unit 1 pcs
C #10 x 3/4” Pan Head Wood Screw 4 pcs
D #8 x 5/8” Pan Head Wood Screw 4 pcs
E #8 x 5/8” Flat Head Wood Screw 4 pcs
E
Rear Bracket Measurements
Face frame
11/32”
1-3/4”
15/16”
1-3/16”
1-5/32”
Bottom of cabinet
20-7/8”
Front plywood
runner
Remove the base from the unit by releasing the slide clips. In
framed cabinets, center the unit in the opening making sure
the front plywood runner is pulled tight against the back of
the face frame. For frameless cabinets, place the unit within
1-1/2” of the left of the cabinet and the front plywood runner
needs to be set back 3/4”. Install with the four (4) #10 x 3/4” Pan
Head Wood Screws provided in the four pre-drilled holes in the
runners. Re-install the unit onto the slides.
STEP 2 - Mark Rear Mounting Bracket STEP 3 - Install Rear Mounting Bracket
Prongs to make
Indentations
If the countertop is installed, pull the organizer partially open to gain access to the upper slide. Firmly
grasping the upper slide, tap it against the back of the cabinet. The rear bracket should make small
indentations in the back of the cabinet. Proceed to step 3. If countertop is not installed, pull the organizer
partially out to gain access to the rear bracket and install three (3) #8 x 5/8” Pan Head Wood Screws provided
in the slots. Proceed to step 4.
Rear mounting bracket
Back of cabinet
STEP 4
Install Pullout Unit
Install Door
Face frame
Remove the unit from the base again and then slide the rear mounting bracket o the slide.
Align the rear bracket prongs with the indentation marks on the rear of the cabinet and
secure with three (3) #8 x 5/8” Pan Head Wood Screws in the slots as shown. Re-install the unit
onto the slides, making sure as you push it in the cabinet, that the top slide is properly seated
into the rear mounting bracket. Operate the unit to make sure the undermount slides are
working properly.
STEP 5
STEP 6
Door Mounting Adjustments
Center of
mounting
bracket slot
to estimated
top of door
Up/Down adjustment (+/- 1/4”)
Tilt adjustment (up to + 1/4”)
C
A
3/16” Setback
Pull the top front mounting bracket into position on the side of the face frame
(or cabinet) allowing for a 3/16” setback (shown left above). Firmly secure with
one (1) # x 5/8” Pan Head Wood Screw. Make sure the gap between the unit
and the side of the face frame is equal from top to bottom. Adjust accordingly
and then securely tighten the bracket set screw (shown right above). Operate
the unit and make adjustments as necessary for the slides to operate smoothly.
Bracket set screw
Door mounting
set screws
Door frame
Loosen the door mounting set screws and slide bracket out to desired
position to attach to the door rail. Measure from the center of the slot
on the door mounting bracket to the estimated top of door. Mark
door with measurement for both top brackets. Install door with the
four (4) #8 x 5/8 Flat Head Phillips Wood Screws provided. (NOTE:
DETERMINE CORRECT SCREW LENGTH TO DOOR PANEL THICKNESS)
B
Left/Right adjustment (+/- 7/8”)
Full extension (+2-1/2”)
To adjust door up or down loosen door mounting
screws (A). To adjust left or right, loosen both
set screws (B) adjust and retighten. To adjust
tilt, loosen both set screws (B) and then turn tilt
screw (C) clockwise to desired distance and then
retighten set screws.
VBPO8-SC/17 v.1
Loading...