COMPACT METAL BENDER
99826
SET UP AND OPERATING INSTRUCTIONS
Distributed exclusively by Harbor Freight Tools®.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Copyright© 2008 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any
artwork contained herein may be reproduced in any shape or form without the express written
consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described
herein. Tools required for assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
SAVE THIS MANUAL
Keep this manual for the safety
warnings and precautions, assembly,
operating, inspection, maintenance and
cleaning procedures. Write the product’s
serial number in the back of the manual
near the assembly diagram (or month and
year of purchase if product has no number). Keep this manual and the receipt in
a safe and dry place for future reference.
NOTICE is used to
address practices
not related to personal injury.
CAUTION, without
the safety alert
symbol, is used to address
practices not related to
personal injury.
General Safety Rules
IMPORTANT SAFETY
INFORMATION
In this manual, on the labeling,
and all other information
provided with this product:
This is the safety alert
symbol. It is used to alert
you to potential personal
injury hazards. Obey all
safety messages that
follow this symbol to avoid
possible injury or death.
DANGER indicates
a hazardous
situation which, if not
avoided, will result in death or
serious injury.
WARNING indicates
a hazardous
situation which, if not
avoided, could result in death
or serious injury.
CAUTION, used
with the safety alert
symbol, indicates a
hazardous situation which, if
not avoided, could result in
minor or moderate injury.
WARNING Read all safety
warnings and instructions.
Failure to follow the warnings and
instructions may result in electric
shock, re and/or serious injury.
Save all warnings and
instructions for future
reference.
Work area safety1.
Keep work area clean and well a.
lit. Cluttered or dark areas invite
accidents.
Do not operate tools in explosive b.
atmospheres, such as in the
presence of ammable liquids,
gases or dust. Tools create
sparks which may ignite the dust or
fumes.
Keep children and bystanders c.
away while operating a tool.
Distractions can cause you to lose
control.
Do not expose tools to rain or d.
wet conditions.
Personal safety2.
Stay alert, watch what you are a.
doing and use common sense
when operating a tool. Do not
use a tool while you are tired or
under the inuence of drugs,
alcohol or medication. A moment of inattention while operating
SKU 99826 For technical questions, please call 1-800-444-3353. Page 2
tools may result in serious personal
injury.
Use personal protective equip-b.
ment. Always wear eye protection. Safety equipment such as
dust mask, non-skid safety shoes,
hard hat, or hearing protection
used for appropriate conditions will
reduce personal injuries.
Do not overreach. Keep proper c.
footing and balance at all times.
This enables better control of the
power tool in unexpected situations.
Dress properly. Do not wear d.
loose clothing or jewelry. Keep
your hair, clothing and gloves
away from moving parts. Loose
clothes, jewelry or long hair can be
caught in moving parts.
Only use safety equipment that e.
has been approved by an appropriate standards agency. Unap-
proved safety equipment may not
provide adequate protection. Eye
protection must be ANSI-approved
and breathing protection must be
NIOSH-approved for the specic
hazards in the work area.
Tool use and care3.
Do not force the tool. Use the a.
correct tool for your application.
The correct tool will do the job better and safer at the rate for which it
was designed.
Store idle tools out of the reach b.
of children and do not allow persons unfamiliar with the power
tool or these instructions to
operate it. Tools are dangerous in
the hands of untrained users.
Maintain tools. Check for mis-c.
alignment or binding of moving
parts, breakage of parts and any
other condition that may affect
the tool’s operation. If damaged,
have the tool repaired before
use. Many accidents are caused
by poorly maintained tools.
Use the tool and bits in accor-d.
dance with these instructions,
taking into account the working
conditions and the work to be
performed. Use of the tool for
operations different from those
intended could result in a hazard-
ous situation.
Bender Safety Warnings
Secure the Bender to a work surface 1.
before use.
Do not bend conduit with wiring 2.
inside.
Maintain labels and nameplates on 3.
the tool. These carry important safety
information. If unreadable or missing, contact Harbor Freight Tools for a
replacement.
This product is not a toy. Keep it out 4.
of reach of children.
The warnings, precautions, and 5.
instructions discussed in this instruction manual cannot cover all possible
conditions and situations that may
occur. It must be understood by the
operator that common sense and caution are factors which cannot be built
into this product, but must be supplied
by the operator.
SKU 99826 For technical questions, please call 1-800-444-3353. Page 3
SPECIFICATIONS
Bend Angle Possible 0 to 90°
Tubing Diameter 1/4”, 3/8”, 1/2” & 5/8”
Round Stock Diameter
Flat Stock Size
3/16”, 1/4”, 5/16”,
3/8”, 7/16” & 1/2”
1/8”X2-1/4”,
3/16”X1-1/2”, 1/4”X1”
work surface. Verify that the installation surface has no hidden utility lines
before drilling or driving screws. Drill
holes and attach the Bender rmly to
the work surface with 1/2” lug bolts
or hexagonal bolts, at washers, and
self locking hex nuts (hardware not
included).
UNPACKING
When unpacking, make sure that
the item is intact and undamaged. If any
parts are missing or broken, please call
Harbor Freight Tools at the number shown
on the cover of this manual as soon as
possible.
INITIAL SET UP INSTRUCTIONS
Read the ENTIRE IMPORTANT
SAFETY INFORMATION
section at the beginning of this
manual including all text under
subheadings therein before set
up or use of this product.
Note: For additional information regarding
the parts listed in the following pages,
refer to the Assembly Diagram near
the end of this manual.
Attach Base Block (6) and Handle (7) 1.
to top of the unit and secure them with
Bolt (11), Washer (12) and Nut (13).
Attach the Bafe (9) to the Right 2.
Frame (3) with Bolt (10). After being
attached the Bafe should still be able
to rotate.
If you will not use the unit for bending 5.
immediately, you may turn the Bafe
(9) inside against the Handle (7) to
prevent it from dropping and causing
damage. See Figure 3.
FIGURE 1
For best use, the Bender should be 3.
mounted to a solid, level work surface
that is capable of bearing the combined weight of both the Bender and
workpiece. See Figure 1.
Use the holes in the base of the 4.
Bender as a template to mark the
SKU 99826 For technical questions, please call 1-800-444-3353. Page 4
OPERATING
INSTRUCTIONS
Read the ENTIRE IMPORTANT
SAFETY INFORMATION
section at the beginning of
this manual including all text
under subheadings therein
before set up or use of this
product.
Select the Die that is appropriate 1.
for the job. The large grooved Die
(22) is for bending small tubes.
The small grooved Die (23) is for
bending small round stock. The
square Die (24) is used to bend at
stock.
Raise the Handle (7) and place the 2.
Die into the slots between the Right
Frame (3) and Left Frame (4).
Insert the stock or tube into the top 3.
of the Bender and thread it into the
appropriate groove between the
Die and the Base Block (6).
The Square Die (24) placed into 4.
the recess in the front of the unit
will provide further support for stock
being bent.
Move the Handle slowly down until 5.
the stock is at the desired angle.
See Figure 1.
FIGURE 2
SKU 99826 For technical questions, please call 1-800-444-3353. Page 5
Swing the Safety Lever (9) back in 6.
place as shown in Figure 3, when not
in use. This will prevent the handle
from accidently falling down without
warning.
FIGURE 3
Safety Lever (9)
USER-MAINTENANCE
INSTRUCTIONS
Procedures not specically
explained in this manual must
be performed only by a qualied
technician.
PLEASE READ THE
FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS
LIST AND ASSEMBLY DIAGRAM IN
THIS MANUAL AS A REFERENCE TOOL
ONLY. NEITHER THE MANUFACTURER
OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY
KIND TO THE BUYER THAT HE OR SHE
IS QUALIFIED TO MAKE ANY REPAIRS
TO THE PRODUCT, OR THAT HE OR
SHE IS QUALIFIED TO REPLACE ANY
PARTS OF THE PRODUCT. IN FACT,
THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT
ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY
CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE
BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER
REPAIRS TO THE ORIGINAL PRODUCT
OR REPLACEMENT PARTS THERETO,
OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS
THERETO.
Cleaning, Maintenance, and
Lubrication
BEFORE EACH USE,1. inspect the
general condition of the tool. Check
for loose screws, misalignment or
binding of moving parts, cracked or
broken parts and any other condition
that may affect its safe operation.
After Use, clean external surfaces of 2.
the tool with clean, moist cloth.
Periodically lubricate the moving parts 3.
of the tool with a high quality machine
oil.
SKU 99826 For technical questions, please call 1-800-444-3353. Page 6
PARTS LIST
Part Description Qty
1 Right Base Board 1
2 Left Base Board 1
3 Right Frame 1
4 Left Frame 1
5 Support Block 1
6 Base Block 1
7 Handle 1
8 Handle Cover 1
9 Safety Lever 1
10 Hex Bolt M6x12 1
11 Hex Bolt M18x120 1
12 Washer 2
PARTS LIST
Part Description Qty
13 Hex Nut M18 1
14 Hex Bolt M10x40 2
15 Spring Washer 2
16 Washer 2
17 Hex Bolt M6x20 8
18 Spring Washer 8
19 Hex Bolt M5x12 1
20 Hex Nut 4
21 Bolt M10x25 4
22 Large Die 1
23 Small Die 1
24 Square Die 1
Note: Some parts are listed and shown for illustration purposes only, and are not avail-
able individually as replacement parts.
SKU 99826 For technical questions, please call 1-800-444-3353. Page 7
LIMITED 90 DAY WARRANTY
Harbor Freight Tools Co. makes every effort to assure that its products meet high
quality and durability standards, and warrants to the original purchaser that this product
is free from defects in materials and workmanship for the period of 90 days from the date
of purchase. This warranty does not apply to damage due directly or indirectly, to misuse,
abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity,
improper installation, normal wear and tear, or to lack of maintenance. We shall in no event
be liable for death, injuries to persons or property, or for incidental, contingent, special
or consequential damages arising from the use of our product. Some states do not allow
the exclusion or limitation of incidental or consequential damages, so the above limitation
of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us
with transportation charges prepaid. Proof of purchase date and an explanation of the
complaint must accompany the merchandise. If our inspection veries the defect, we
will either repair or replace the product at our election or we may elect to refund the
purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that
the defect resulted from causes not within the scope of our warranty, then you must bear
the cost of returning the product.
This warranty gives you specic legal rights and you may also have other rights
which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
SKU 99826 For technical questions, please call 1-800-444-3353. Page 8
Loading...