Harbor Freight Tools 99701 User Manual

LOW PROFILE

REAR MOTORCYCLE

99701

SPOOL STAND

INSTRUCTIONS AND PRECAUTIONS

Distributed exclusively by Harbor Freight Tools®.

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our website at: http://www.harborfreight.com

SAVE THESE INSTRUCTIONS. READ ALL

PRECAUTIONS AND INSTRUCTIONS.

Copyright© 2008 by Harbor Freight Tools®. All rights reserved. No portion of this document or any artwork contained
herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this document may not be drawn proportionally. Due to continuing improvements, actual product
may differ slightly from the product described herein. Tools required for assembly and service may not be included.

For technical questions or replacement parts, please call 1-800-444-3353.

SPECIFICATIONS

Maximum Weight Capacity 700 Lbs. Maximum

Adjustable Width

10-1/2” min. to 14”
max.

UNPACKING

When unpacking, check to make sure that
the item is intact and undamaged. If any parts are
missing or broken, please call Harbor Freight Tools
at the number shown on the cover of this document
as soon as possible.

IMPORTANT SAFETY

INFORMATION

Assembly Precautions

Assemble only according to these instruc-1.

tions. Improper assembly can create haz-

ards.

Wear ANSI-approved safety goggles and 2.

heavy-duty work gloves during assembly.

Keep assembly area clean and well lit.3.

Keep bystanders out of the area during as-4.
sembly.

Do not assemble when tired or when under 5.

the inuence of drugs or medication.

Use Precautions

This product is not a toy. Do not allow chil-1.
dren to play with or near this item.

Use for intended purpose(s) only. Not for any 2.
aircraft purpose.

Inspect before use; do not use if parts loose 3.

or damaged.

The oor must be rm, level and in good 4.

repair. The oor must be strong enough to

support the weight of the tool and the vehicle.

Maintain product labels and nameplates. 5.

These carry important safety information.

If unreadable or missing, contact Harbor

Freight Tools for a replacement.

ASSEMBLY INSTRUCTIONS

Loosely assemble the Bracket Covers (3) to 1.

the ends of each Support Arm (2) using the

Bolts (11).

Insert the Square rods of the Left and Right 2.

Support Brackets (4 and 5) into the Bracket

Covers as shown in the assembly diagram.
Note: The Paddle Adapters (12, sold separately)

can be used instead of the Support Brackets.

Adjust the Left and Right Support Brackets to 3.

match the width of your motorcycle axle.

Tighten the Support Brackets rmly in place 4.

by tightening the Bolts (11).

PARTS LIST

Part Description Qty.

1 Handle 1
2 Support Arm 2
3 Bracket Cover 2
4 Left Support Bracket 1
5 Right Support Bracket 1
6 Wheel 2
7 Bolt m8 x 50 2
8 Nut m8 2

9 Bolt m6 x 50 2
10 Nut m6 2
11 Bolt m6 x 18 8
12 Paddle Adapter (not included) 1 Set

Record Serial Number Here:
Note: If product has no serial number, record

month and year of purchase instead.

Note: Some parts are listed and shown for illustra-

tion purposes only, and are not available
individually as replacement parts.

OPERATION

If your motorcycle kick stand holds the ve-1.
hicle vertically upright, you can use the kick
stand. Otherwise, have an assistant hold the
vehicle vertically upright.

Holding the Handle (1), roll the Stand under 2.
the rear of the motorcycle. Align and engage
the Left and Right Support Brackets (4 and

5) with the axle of the motorcycle.
When the brackets are rmly engaged, lower 3.

the Handle (1), lifting the rear of the motor­cycle. Lower the Handle all the way to the

oor, which will create a support base for the

vehicle. CAUTION: Do not attempt to lift the
motorcycle if the Support Brackets are not
fully engaged with the vehicle axle.

To raise the vehicle, have an assistant sup-4.
port the handlebars. Raise the Handle (1)
from the oor, which will lower the motor­cycle.

Disengage the Stand from the motorcycle 5.
axle, and roll it away.

Put the motorcycle on its kick stand. Store 6.
this tool in a safe place.

PLEASE READ THE FOLLOWING

CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS
PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN
THIS DOCUMENT AS A REFERENCE TOOL ONLY. NEITHER
THE MANUFACTURER OR DISTRIBUTOR MAKES ANY
REPRESENTATION OR WARRANTY OF ANY KIND TO THE
BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY
REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.
IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR
EXPRESSLY STATES THAT ALL REPAIRS AND PARTS
REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED
AND LICENSED TECHNICIANS, AND NOT BY THE BUYER.
THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING
OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT
OR REPLACEMENT PARTS THERETO, OR ARISING OUT
OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS
THERETO.

REV 08i; 09b

SKU 99701 For technical questions, please call 1-800-444-3353. Page 2