Page 1
20” PUSH/PULL
Model
98383
STEEL LAWN ROLLER
ASSEMBLY, OPERATING, AND MAINTENANCE
INSTRUCTIONS
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
Distributed exclusively by Harbor Freight Tools®.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Copyright© 2008 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
Page 2
SAVE THIS MANUAL
Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning
procedures. Write the product’s serial
number in the back of the manual near the
assembly diagram (or month and year of
purchase if product has no number). Keep
this manual and the receipt in a safe and
dry place for future reference.
CAUTION, used
with the safety
alert symbol,
indicates a hazardous
situation which, if not
avoided, could result in minor
or moderate injury.
NOTICE is used to
address practices
not related to
personal injury.
IMPORTANT SAFETY
INSTRUCTIONS
In this manual, on the labeling, and all other
information provided with this product:
This is the safety alert
symbol. It is used to alert
you to potential personal
injury hazards. Obey all
safety messages that
follow this symbol to avoid
possible injury or death.
DANGER indicates
a hazardous
situation which, if
not avoided, will result in
death or serious injury.
CAUTION, without
the safety alert
symbol, is used to
address practices not related
to personal injury.
GENERAL AND SPECIFIC
SAFETY RULES
1. To protect your feet, always
wear steel toed shoes or
boots when working with
this Steel Lawn Roller.
Wear ANSI-approved safety
goggles and heavy-duty
work gloves. Use face or
dust mask if operation is
dusty.
WARNING
indicates a
hazardous
situation which, if not
avoided, could result in death
or serious injury.
Use only on at, level surfaces. 2.
Weight of Steel Lawn Roller if used
on angle surfaces may cause a loss
of control and possible severe injury.
Do not Overreach - Keep proper foot-3.
ing and balance at all times.
Stay Alert - Watch what you are 4.
doing. Use common sense. Do not
operate this tool when you are tired.
Page 2SKU 98383 For technical questions, please call 1-800-444-3353.
Page 3
Keep hands and feet away from Roll-5.
er Barrel when using. Never stand in
the direct path of the Roller.
supplied by the operator.
Do not Use on wet, or damp lawn 6.
or dirt. Grass, mud and debris can
build up at Roller Barrel Axle and/or
against the Scraper Plate (6) causing
the Barrel to become hard to push.
Keep Children Away and never al-7.
low them to play with this Steel Lawn
Roller. All visitors should be kept at a
distance from work area. Keep pets
out of the work area.
When servicing use only identical 8.
replacement parts.
When not in use, store this Steel 9.
Lawn Roller Indoors.
Maintain Steel Lawn Roller with care. 10.
Keep Roller Barrel clean for best performance. Inspect Steel Lawn Roller
periodically, and if damaged, have
it repaired by an authorized service
facility. Keep handles dry, clean, and
free from oil and grease.
Do not use this Steel Lawn Roller for 11.
other than intended use.
Maintain labels and nameplates on 12.
the appliance. These carry important
safety information. If unreadable or
missing, contact Harbor Freight Tools
for a replacement.
The warnings, precautions, and 13.
instructions discussed in this
instruction manual cannot cover all
possible conditions and situations
that may occur. It must be understood
by the operator that common sense
and caution are factors which cannot
be built into this product, but must be
SAVE THESE
INSTRUCTIONS.
SPECIFICATIONS
Roller Barrel: Formed, Round
Steel.
Construction
Overall Height 42-1/2” High
Net Weight 23.40 LB (Empty)
When unpacking, check to make sure
that the item is intact and undamaged. If
any parts are missing or broken, please
call Harbor Freight Tools at the number
shown on the cover of this manual as soon
as possible.
Note: For additional information regarding
the parts listed in the following pages,
refer to the Assembly Diagram near
the end of this manual.
Mount the two Lower Handles (7) to 1.
the axle of the Roller Barrel (1) and
secure each side with a Cap Nut (3).
Mount the Top Handle (10) to the 2.
Lower Handles (7) using the Bolts (8)
and the Lock-Washer Nuts (9). Refer
to “Assembly Diagram” on page 6 for
Upper and Lower Handle:
Formed Steel.
All Hardware: Carbon Steel.
Drain Plug: Hard Rubber.
UNPACKING
ASSEMBLY
Page 3SKU 98383 For technical questions, please call 1-800-444-3353.
Page 4
correct insertion direction for Bolts
(8).
subheadings therein before set
up or use of this product.
Attach the Scraper Plate (6) through 3.
the existing holes in each of the
Lower Handles (7) using the Nuts (5)
and the Bolts (4).
Figure 1
Drain Plug
Drain
Before operating the Steel Lawn 1.
Roller, put on ANSI-approved safety
goggles, steel toe shoes and other
safety gear. Safety goggles and
other safety gear are sold separately.
Roll the Steel Lawn Roller to the area 2.
to be compacted.
Use the Steel Lawn Roller as you 3.
would if you were mowing a lawn.
Roll one direction until all areas are
rolled, then roll the other direction till
area is completely rolled again.
If it is necessary to wash or clean 4.
debris from the Roller Barrel before
you are nished using it, be sure to
dry the surface with a towel or absor-
bent cloth to prevent a quick build up
of added debris.
4. Add weight to the Steel Lawn Roller
by standing the empty Roller Barrel
on it’s side with the Drain Hole up.
Remove the Drain Plug (2), then using a funnel (not supplied) carefully
pour water or sand into the opening
until full. (Sand would give maximum
weight.) See Figure 1.
Using two people for added safety, 5.
carefully lay the Steel Lawn Roller
onto the ground.
OPERATING INSTRUCTIONS
Read the ENTIRE
IMPORTANT SAFETY
INFORMATION section at the
beginning of this manual
including all text under
When completely nished with your 5.
project, wash off the Steel Lawn
Roller with a hose and soft rag or
brush and let stand until completely
dry before storing. Store in garage or
shed away from children.
MAINTENANCE AND
SERVICING
TO PREVENT SERIOUS INJURY FROM
TOOL FAILURE:
Do not use damaged equipment. If anything abnormal is noticed, or occurs while
using, have the problem corrected before
further use.
Procedures not
specically explained in this
manual must be performed only
by a qualied technician.
Page 4SKU 98383 For technical questions, please call 1-800-444-3353.
Page 5
Cleaning, Maintenance, and
Lubrication
Use a small amount of axle grease to 1.
lubricate axles periodically.
Before use, check for cracks in Top 2.
and Lower Handles and/or in Roller
Barrel. If any damage is found, have
the problem repaired before using.
After using, wipe away all dirt and 3.
debris with clean, damp (with water)
cloth, then dry and store inside away
from children.
Never put lubricants over the Roller 4.
Barrel.
NOTE: If the Steel Lawn Roller has been
lled with water and is to be stored
for an extended period of time, empty the water by removing the Drain
Plug and allowing the water to drain
completely. Dry sand may remain
inside the Roller Barrel while stored.
PLEASE READ THE FOLLOWING CAREFULLY
PARTS LIST
Part # Discription Q’ty
1 Roller Barrel 1
2 Drain Plug 1
3 Cap Nut 2
4 Bolt (M6x35) 2
5 Nut (M6) 2
6 Scraper Plate 2
7 Lower Handle 2
8 Bolt (M5 X 30) 2
9 Lock-Washer Nut (M5) 2
10 Top Handle 1
THE MANUFACTURER AND/OR DISTRIBUTOR
HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS MANUAL AS A REFERENCE
TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION
OR WARRANTY OF ANY KIND TO THE BUYER
THAT HE OR SHE IS QUALIFIED TO MAKE ANY
REPAIRS TO THE PRODUCT, OR THAT HE OR SHE
IS QUALIFIED TO REPLACE ANY PARTS OF THE
PRODUCT. IN FACT, THE MANUFACTURER AND/
OR DISTRIBUTOR EXPRESSLY STATES THAT ALL
REPAIRS AND PARTS REPLACEMENTS SHOULD
BE UNDERTAKEN BY CERTIFIED AND LICENSED
TECHNICIANS, AND NOT BY THE BUYER. THE
BUYER ASSUMES ALL RISK AND LIABILITY ARISING
OUT OF HIS OR HER REPAIRS TO THE ORIGINAL
PRODUCT OR REPLACEMENT PARTS THERETO,
OR ARISING OUT OF HIS OR HER INSTALLATION
OF REPLACEMENT PARTS THERETO.
Page 5SKU 98383 For technical questions, please call 1-800-444-3353.
Page 6
ASSEMBLY DIAGRAM
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only, and are not avail-
able individually as replacement parts.
Page 6SKU 98383 For technical questions, please call 1-800-444-3353.
Loading...