Harbor Freight Tools 98019 Owner's Manual
2-Bike Hitch Rack
Item 98019
INSTRUCTIONS AND PRECAUTIONS
Visit our website at:
http://www.harborfreight.com
Read this material before
using this product.
Failure to do so can result
in serious injury.
SAVE THIS MANUAL.
When unpacking, make sure that the
product is intact and undamaged.
If any parts are missing or broken,
please call
1-800-444-3353 as soon as possible.
Specications
Maximum Weight Capacity 100 lbs
Bike Capacity 2
Holding Mechanism
Hitch Classes
Swing-down feature For opening hatches
Thermoplastic Bike Holders,
Hook & Loop Straps
Used with
Class I, II, III, IV Hitches
Unpacking
When unpacking, check to make sure that the item
is intact and undamaged. If any parts are missing or
broken, please call Harbor Freight Tools at the number
shown on the cover of this document as soon as possible.
Important Safety Information
1. Assemble only according to these instructions.
Improper assembly can create hazards.
2. Wear ANSI-approved safety goggles and heavy-
duty work gloves during assembly.
3. Keep assembly area clean and well lit.
4. Keep bystanders out of the area during assembly.
5. Do not assemble when tired or when under the
inuence of drugs or medication.
6. Do not exceed 55 MPH with Carrier attached.
7. Contact the Department of Transportation (DOT)
and check local regulations for laws regarding the
installation and use of this bike rack.
8. This product is not a toy. Do not allow children to
play with or on this item.
9. Use for intended purpose(s) only.
10. Inspect before use; do not use if parts are loose or
damaged.
11. Maintain product labels and nameplates. These
carry important safety information. If unreadable or
missing, contact Harbor Freight Tools for a replace-
ment.
Copyright© 2008 by Harbor Freight Tools®. All rights reserved. No
portion of this document or any artwork contained herein may be
reproduced in any shape or form without the express written consent
of Harbor Freight Tools. Diagrams within this document may not be
drawn proportionally. Due to continuing improvements, actual product
may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call
1-800-444-3353.
Manual Revised 11c
Instructions
Read the ENTIRE INSTRUCTIONS AND
PRECAUTIONS section at the beginning of
this document including all text under
subheadings therein before set up or use of
this product.
Assembly
1. Slide the Hitch End of the Linker (1) into the vehicle’s trailer hitch and lock with a steel pin. See
Figure 1.
2. Install the Support Column (2) to the upright part
of the Linker (1) and secure with a Bolt (5), Nut (7)
and two Washers (6), through the bottom hole and
the Hitch Pin (4) through the upper hole. When the
back hatch or tailgate has to be accessed, pull the
Hitch Pin (4) out and swing the rack downward,
pivoting at the bolt directly below the Hitch Pin (4).
3. Hold the two Bike Rack (3) sections over the upper
end of the Support Column (2) aligning the bolt
holes. Secure this with two Bolts (5), four Washers
(6) and two Nuts (7).
4. Double check all nuts and bolts, making sure they
are all tight.
Operation
Note: This rack is designed to hold up to two bikes.
1. Make sure that the holders are facing upwards.
Open the straps and place the bicycle’s cross-bar
onto the holders. Close the straps over the bike,
pressing the straps together for a secure hold.
Place the second bike facing in the opposite direction and secure it with the hook & loop straps as
well.
2. The Thermoplastic Holders keep the bike(s) in position, preventing them from sliding back and forth,
causing damage. The straps keep the bikes from
bumping out of the holders.
Note: It is recommended that if you plan to carry only one
bike, you can place it in the position closest to the
vehicle.
3.
4.
5. Assembly Diagram
REV 11c
Page 2SKU 98019 For technical questions, please call 1-800-444-3353.
Loading...