Page 1
Page 2
will result in death or serious injury.
Addresses practices not related to personal injury.
Warnings
Work area safety
SAFETY OPERATION MAINTENANCESETUP
WARNING SYMBOLS AND DEFINITIONS
IMPORTANT SAFETY INFORMATION
Page 3
Unmodified plugs and matching
Avoid body contact with grounded surfaces
Water entering a power tool
When operating a power tool outdoors,
Use of a cord suitable for outdoor
A
power tools may result in serious personal injury.
wear
Safety
A
This enables better control
jewelry. Keep your hair, clothing and gloves
Loose clothes, jewelry
parts.
protection
ANSI
SAFETYOPERATIONMAINTENANCE SETUP
Page 4
power tool will do the job better and
Any
power
preventive safety measures reduce the
with the power tool or these instructions
Power tools are
Many accidents
Properly
Use of the
power tool for operations different from those
Warnings
when performing an operation where the cutting
parts of the tool ″live″ and shock the operator.
while in use, and can burn you.
Avoid unintentional starting.
SAFETY OPERATION MAINTENANCESETUP
Page 5
Your risk from these exposures varies, depending on
filter out microscopic particles.
factors which cannot be built into this product,
Vibration Safety
Anyone using vibrating tools regularly or for an
worsened from use. Pregnant women or people who
feel
when there is a
SAVE THESE INSTRUCTIONS.
Warnings (cont.)
SAFETYOPERATIONMAINTENANCE SETUP
Page 6
Grounding
WIRE
wire cord and three prong grounding plug. The plug
Association, and the National Electrical Code.
SAFETY OPERATION MAINTENANCESETUP
Page 7
tools require a three wire
tools can use either
As the distance from the supply outlet increases,
wire causes a serious drop in voltage, resulting
A on page
A.)
A.)
A.)
ABLE
A:
VOLT)
AMPERES
V~
Volts Alternating Current
A
Amperes
xxxx/min.
ANSI
flammable objects away.
SAFETYOPERATIONMAINTENANCE SETUP
Page 8
Specifications
section at the beginning of this
For additional information regarding the parts listed in the following
For additional information regarding the parts listed in the following
on page
Assembly
SAFETY OPERATION MAINTENANCESETUP
Setup - Before Use:
224184
Page 9
SAFETYOPERATIONMAINTENANCE SETUP
Page 10
Operating Instructions
section at the beginning of this
with a bit shank diameter from 1/8″ to 1/2″. Do not
Speed Switch must be completely in the
while the Drill is running, under a load, or when the tool
Work Piece and Work Area Set Up
SAFETY OPERATION MAINTENANCESETUP
Page 11
Torque will cause the Drill to twist sharply.
Torque will cause the Drill to twist sharply.
Hands or other body
After the Drill Bit cuts through the workpiece,
SAFETYOPERATIONMAINTENANCE SETUP
Page 12
Maintenance and Servicing
inspect the general condition
AFTER USE,
wipe external surfaces
WARNING! If the supply cord of this
SAFETY OPERATION MAINTENANCESETUP
Page 13
wear.
Allow tool to work at its own rate.
for its length and load. See
SAFETYOPERATIONMAINTENANCE SETUP
Page 14
Armature
Parts List and Diagram
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
If product has no serial number, record month and year of purchase instead.
If product has no serial number, record month and year of purchase instead.
Some parts are listed and shown for illustration purposes only,
Some parts are listed and shown for illustration purposes only,
SAFETY OPERATION MAINTENANCESETUP
Page 15
Assembly Diagram
SAFETYOPERATIONMAINTENANCE SETUP
Page 16
Limited 90 Day Warranty
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
Loading...