STAINLESS STEEL ROLLING
Model
97320
CABINET
SET UP AND OPERATING INSTRUCTIONS
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
Distributed exclusively by Harbor Freight Tools®.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Copyright© 2007 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
SAVE THIS MANUAL
Keep this manual for the safety warnings and precautions, assembly, operating,
inspection, maintenance and cleaning procedures. Write the product’s serial number
in the back of the manual near the assembly diagram (or month and year of purchase if
product has no number). Keep this manual and the receipt in a safe and dry place for
future reference.
WARNING! Read all instructions
Failure to follow all instructions listed below may result in serious injury.
SAVE THESE INSTRUCTIONS
WORK AREA SAFETY
1.
2.
1.
2.
3.
4.
Keep children and bystanders away while operating. Distractions can
cause you to lose control.
Keep work area clean and well lit. Cluttered or dark areas invite accidents.
PERSONAL SAFETY
Wear ANSI-approved safety goggles, NIOSH-approved dust mask/respira-
tor, and heavy-duty work gloves during use and service.
Stay alert and use common sense when operating. Do not use when tired or
under the inuence of drugs, alcohol or medication.
Do not overreach. Keep proper footing and balance at all times. This enables
better control in unexpected situations.
Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing
and gloves away from moving parts. Loose clothes, jewelry or long hair can be
caught in moving parts.
PRODUCT USE AND CARE
1.
2.
3.
This product is not a toy. Keep it out of reach of children.
Use the correct product for your application. The correct product will do the job
better and safer at the rate for which it was designed. Do not modify this product
or use it for a purpose for which it is not intended.
Check for misalignment or binding of moving parts, breakage of parts and any
other condition that may affect the product’s operation. If damaged, have the
product repaired before use.
Page 2SKU 97320 For technical questions, please call 1-800-444-3353.
4.
Use the product in accordance with these instructions and in the manner intend-
ed for the particular type of product, taking into account the working conditions
and the work to be performed. Use of the product for operations different from
those intended could result in a hazardous situation.
SERVICE
1.
2.
1.
2.
3.
4.
5.
6.
7.
Have product serviced by a qualied repair person using only identical replace-
ment parts. This will ensure that the safety of the product is maintained.
Maintain labels and nameplates on the product. These carry important safety
information. If unreadable or missing, contact Harbor Freight Tools for a replace-
ment.
MISCELLANEOUS
Do not exceed the weight capacity of the drawers, shelves or cabinet.
Be aware of dynamic loading! Dropping or bouncing a heavy item may briey
create excess load causing product failure.
Depress the locks on all casters before use.
Do not open more than one drawer at a time.
Load the Cabinet evenly, from the bottom up.
Do not step on drawers.
The warnings, precautions, and instructions discussed in this instruction manual
cannot cover all possible conditions and situations that may occur. It must be
understood by the operator that common sense and caution are factors which
cannot be built into this product, but must be supplied by the operator.
SAVE THESE INSTRUCTIONS.
Page 3SKU 97320 For technical questions, please call 1-800-444-3353.
SPECIFICATIONS
Drawers: 95 Pounds
Weight Capacity
Top Shelf: 500 Pounds
Overall: 1355 Pounds
UNPACKING
When unpacking, check to make sure that the item is intact and undamaged. If
any parts are missing or broken, please call Harbor Freight Tools at the number shown
on the cover of this manual as soon as possible.
OPERATING INSTRUCTIONS
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the
beginning of this manual including all text under subheadings therein
before set up or use of this product.
1.
2.
3.
4.
5.
6.
Load the Cabinet from the bottom up, evenly distributing weight.
Use the keys to lock the cabinet before moving it.
Only use or move the cabinet on a smooth, level surface, capable of bearing the
combined weight of the Cabinet, tools loaded, and the operator.
To remove a drawer; empty it, and pull the drawer all the way out. On each side
of the back of the drawer, there are small levers on the slider; the lever on the left
side must be pulled up, and the lever on the right side pushed down, to remove
the drawer. Holding the levers in position, slide the drawer off the end of the slid-
ers.
The drawer can be slid back onto the slider and closed with no extra operations.
Clean, then store the product indoors out of children’s reach.
CAUTIONCAUTION
MAINTENANCE AND SERVICING
Damaged products can fail, causing personal injury. Do
not use a damaged product. If abnormal noise or vibration
occurs, have the problem corrected before further use.
1.
2.
BEFORE EACH USE, inspect the general condition of the product. Check for
loose screws, misalignment or binding of moving parts, cracked or broken parts
and any other condition that may affect its safe operation.
PERIODICALLY, clean external surfaces of the product with clean, moist cloth.
Page 4SKU 97320 For technical questions, please call 1-800-444-3353.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT
HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR
DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD
BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE
BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE
ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER
INSTALLATION OF REPLACEMENT PARTS THERETO.
PARTS LIST & DIAGRAM
Part Description Qty
1 Piston 1
2 Shelf 1
3 Drawer A 2
4 Drawer B 1
5 Drawer C 1
6 Drawer D 1
7 Casters 4
1
2
3
4
5
8
Part Description Qty
8 Drawer E 2
9 Drawer F 2
10 Lid Handle 1
11 Slider 18
12 Key (not shown) 2
13 Side Handles 2
14 Slider 18
10
11
12
13
6
7
9
14
Page 5SKU 97320 For technical questions, please call 1-800-444-3353.
LIMITED 90 DAY WARRANTY
Harbor Freight Tools Co. makes every effort to assure that its products meet high
quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from
the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities,
criminal activity, improper installation, normal wear and tear, or to lack of maintenance.
We shall in no event be liable for death, injuries to persons or property, or for incidental,
contingent, special or consequential damages arising from the use of our product. Some
states do not allow the exclusion or limitation of incidental or consequential damages, so
the above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE
WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us
with transportation charges prepaid. Proof of purchase date and an explanation of the
complaint must accompany the merchandise. If our inspection veries the defect, we
will either repair or replace the product at our election or we may elect to refund the
purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that
the defect resulted from causes not within the scope of our warranty, then you must
bear the cost of returning the product.
This warranty gives you specic legal rights and you may also have other rights
which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only, and are not avail-
able individually as replacement parts.
Page 6SKU 97320 For technical questions, please call 1-800-444-3353.
Loading...