3 POINT QUICK HITCH
Model
97214
SET UP AND OPERATING INSTRUCTIONS
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
Distributed exclusively by Harbor Freight Tools®.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Copyright© 2007 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
Revised 09g
SAVE THIS MANUAL
Keep this manual for the safety warnings and precautions, assembly, operating,
inspection, maintenance and cleaning procedures. Write the product’s serial number
in the back of the manual near the assembly diagram (or month and year of purchase if
product has no number). Keep this manual and the receipt in a safe and dry place for
future reference.
IMPORTANT SAFETY INFORMATION
In this manual, on the labeling, and all other information
provided with this product:
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that follow this
symbol to avoid possible injury or death.
DANGER
WARNING
CAUTION
Notice
CAUTION
DANGER indicates a hazardous situation
which, if not avoided, will result in death or
serious injury.
WARNING indicates a hazardous situation
which, if not avoided, could result in death
or serious injury.
CAUTION, used with the safety alert
symbol, indicates a hazardous situation
which, if not avoided, could result in minor
or moderate injury.
NOTICE is used to address practices not
related to personal injury.
CAUTION, without the safety alert symbol,
is used to address practices not related to
personal injury.
Page 2SKU 97214 For technical questions, please call 1-800-444-3353.
WARNING! Read all instructions
Failure to follow all instructions listed below may result in serious injury.
SAVE THESE INSTRUCTIONS
WORK AREA SAFETY
Keep children and bystanders away while operating. Distractions can 1.
cause you to lose control.
Keep work area clean and well lit. Cluttered or dark areas invite accidents.2.
PERSONAL SAFETY
Wear ANSI-approved safety goggles, NIOSH-approved dust mask/1.
respirator, and work gloves during use and service.
Stay alert and use common sense during set-up and when operating. Do not use 2.
when tired or under the inuence of drugs, alcohol or medication.
Do not overreach. Keep proper footing and balance at all times. This enables 3.
better control in unexpected situations.
Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing 4.
and gloves away from moving parts. Loose clothes, jewelry or long hair can be
caught in moving parts.
PRODUCT USE AND CARE
This product is not a toy. Keep it out of reach of children.1.
Use the correct product for your application. The correct product will do the job 2.
better and safer at the rate for which it was designed. Do not modify this product
or use it for a purpose for which it is not intended.
Check for misalignment or binding of moving parts, breakage of parts and any 3.
other condition that may affect the product’s operation. If damaged, have the
product repaired before use.
Use the product and accessories etc., in accordance with these instructions and 4.
in the manner intended for the particular type of product, taking into account
the working conditions and the work to be performed. Use of the product for
operations different from those intended could result in a hazardous situation.
Page 3SKU 97214 For technical questions, please call 1-800-444-3353.
SERVICE
Have product serviced by a qualied repair person using only identical 1.
replacement parts. This will ensure that the safety of the product is maintained.
Maintain labels and nameplates on the product. These carry important safety 2.
information. If unreadable or missing, contact Harbor Freight Tools for a
replacement.
MISCELLANEOUS
For off-road use only. 1.
Hitch connections need to be capable of supporting the weight of the Hitch and 2.
attached implement, plus load.
The warnings, precautions, and instructions discussed in this instruction manual 3.
cannot cover all possible conditions and situations that may occur. It must be
understood by the operator that common sense and caution are factors which
cannot be built into this product, but must be supplied by the operator.
SAVE THESE INSTRUCTIONS.
Page 4SKU 97214 For technical questions, please call 1-800-444-3353.
SPECIFICATIONS
Capacity Fits most Category 1 Tractors up to 45 HP.
Distance Between Arms 27-1/2”
Maximum Weight Capacity: 2000 lbs., dependent on tractor’s hitch capacity.
UNPACKING
When unpacking, check to make sure that the item is intact and undamaged. If
any parts are missing or broken, please call Harbor Freight Tools at the number shown
on the cover of this manual as soon as possible.
SET UP INSTRUCTIONS
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the
beginning of this manual including all text under subheadings therein
before set up or use of this product.
Note: For additional information regarding the parts listed in the following pages, refer
to the Assembly Diagram near the end of this manual.
Tractor Center Link
Top Hook
Tractor Lift Arms
Lower
Hook
Clevis Pin (3)
Implement
Note: It is recommended that two people assist when connecting this product.
Fasten the Quick Hitch to the tractor’s lift arms using a Clevis Pin (3) with a at 1.
bracket on one end, and secure with linchpins. See illustration above.
Fasten the tractor’s Center Link to the top bracket of the Quick Hitch using a 2.
Clevis Pin (not included).
Adjust the height of the Top Hook and connect it to the implement with a Link Pin 3.
(not included).
REV 09g
Page 5SKU 97214 For technical questions, please call 1-800-444-3353.
Insert the implement’s lower mounts inside the hitch hooks, and lock by pressing 4.
down the latch handles.
Check that all connections are tight before starting the work task.5.
If the tractor has stabilizer arms, they will not t into the Quick Hitch mounting 6.
area along with the lift arms. Use stabilizer chains, or some other longer
Mounting Pin (neither included) to fasten the Quick Hitch to the tractor.
Latch Handle
Top Hook
Clevis pin (4)
R Pin (4)
Lower Hook
Top Bracket
Latch Handle
Linchpin (4)
Lower Hook
Mounting Non-ASAE Implements
If the implement does not meet ASAE specications, use an Adapter Bracket (not 1.
included) to mount it to the Quick Hitch as illustrated on the next page.
Remove the Top Hook by taking out the two Hex Bolts (2), Lock Washers (6), and 2.
Nut (7). Save hardware.
Slide the Adapter Bracket over the Top Bracket of the Quick Hitch, and attach the 3.
top Link Pin.
For most implements, the front hole (closest to implement) is recommended for 4.
the best vertical alignment.
Attach the implement to the Adapter Bracket tab with a Link Pin.5.
Check that all connections are tight before starting a task.6.
Page 6SKU 97214 For technical questions, please call 1-800-444-3353.
Adapter Bracket
(not included)
Link Pins
(not included)
Top Bracket
Implement
Quick Hitch
Tractor Center Link
MAINTENANCE AND SERVICING
CAUTION
BEFORE EACH USE,1. inspect the general condition of the product. Check for
loose screws, misalignment or binding of moving parts, cracked or broken parts,
and any other condition that may affect its safe operation.
AFTER USE,2. clean external surfaces of the product with clean, moist cloth.
Lubricate the Quick Hitch periodically for best results.3.
Damaged products can fail, causing personal injury. Do
not use a damaged product. If abnormal noise or vibration
occurs, have the problem corrected before further use.
Cleaning, maintenance, and lubrication
Page 7SKU 97214 For technical questions, please call 1-800-444-3353.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT
HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR
DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE
UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER
ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL
PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION
OF REPLACEMENT PARTS THERETO.
PARTS LIST & ASSEMBLY DIAGRAM
Part Description Qty
1 Main Frame 1
2 Hex Bolt 1/2x2-1/8 2
3 Clevis Pin 2
4 R Pin 3
Part Description Qty
5 Hook 1
6 Nut 2
7 Lock Washer 2
8 Clevis Pin 1
Page 8SKU 97214 For technical questions, please call 1-800-444-3353.
LIMITED 90 DAY WARRANTY
Harbor Freight Tools Co. makes every effort to assure that its products meet high
quality and durability standards, and warrants to the original purchaser that this product
is free from defects in materials and workmanship for the period of 90 days from the date
of purchase. This warranty does not apply to damage due directly or indirectly, to misuse,
abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity,
improper installation, normal wear and tear, or to lack of maintenance. We shall in no event
be liable for death, injuries to persons or property, or for incidental, contingent, special
or consequential damages arising from the use of our product. Some states do not allow
the exclusion or limitation of incidental or consequential damages, so the above limitation
of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with
transportation charges prepaid. Proof of purchase date and an explanation of the complaint
must accompany the merchandise. If our inspection veries the defect, we will either
repair or replace the product at our election or we may elect to refund the purchase price
if we cannot readily and quickly provide you with a replacement. We will return repaired
products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning
the product.
This warranty gives you specic legal rights and you may also have other rights
which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only, and are not available
individually as replacement parts.
Page 9SKU 97214 For technical questions, please call 1-800-444-3353.
Loading...