Harbor Freight Tools 94668 User Manual

Owner’s Manual & Safety Instructions

Save This Manual Keep this manual for the safety warnings and precautions, assembly,

operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.

REV 14h

When unpacking, make sure that the product is intact

and undamaged. If any parts are missing or broken,

please call 1-888-866-5797 as soon as possible.

Copyright© 2006 by Harbor Freight Tools®. All rights reserved.

No portion of this manual or any artwork contained herein may be reproduced in

any shape or form without the express written consent of Harbor Freight Tools.

Diagrams within this manual may not be drawn proportionally. Due to continuing

improvements, actual product may differ slightly from the product described herein.

Tools required for assembly and service may not be included.

Email our technical support at: [e-mail]

Visit our website at: http://www.harborfreight.com

Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.

Specifications

Overall Length 17-1/2"
LED Lights 30
Charging Indicator Light 1
Light Wattage 40
Battery 7.2V, 600mA/H rechargeable NiMH, lasts up to 2 hours
Adapter 9V AC/DC
Includes Cigarette Lighter Charger, 2 additional hanging hooks

Important Safety Information

WARNING: When using product, basic
safety precautions should always be
followed to reduce the risk of personal
injury and damage to equipment.

1. Keep work area clean and well
lighted. Cluttered areas invite injuries.

2. Store idle equipment. When not in
use, the Worklight must be stored in a
dry location. Always lock up products
and keep out of reach of children.

3. Use the right product for the job. There
are certain applications for which the
Worklight was designed. Do not modify the
Worklight and do not use the Worklight for
a purpose for which it was not intended.

4. Check for damaged parts. Before
using any product, any part that appears
damaged should be carefully checked
to determine that it will operate properly
and perform its intended function.
Check for any broken or damaged
parts and any other conditions that may
affect its operation. Replace or repair
damaged or worn parts immediately.

5. Replacement parts and accessories.
When servicing, use only identical
replacement parts. Use of any other
parts will void the warranty.

6. Do not operate product if under the
influence of alcohol or drugs. Read
warning labels on prescriptions to
determine if your judgment or reflexes
are impaired while taking drugs. If there
is any doubt, do not operate the product.

7. Do not expose the Worklight to rain or
wet conditions. Water entering a power
tool will increase the risk of electric shock.

8. Do not abuse the Power Cord. Never

use the Power Cord to carry the
Worklight or to pull the Plug from an
outlet. Keep the Power Cord away
from heat, oil, sharp edges, or moving
parts. Replace damaged Power Cords
immediately. Damaged Power Cords

increase the risk of electric shock.

9. Disconnect the Power Cord

before making any adjustments,
changing accessories, or storing
the Worklight. Such preventive

safety measures reduce the risk of
turning on the product accidentally.

10. Never leave the Worklight unattended

when it is plugged into an electrical
outlet. Turn off the Worklight and

unplug it from its electrical outlet
before leaving the work area.

11. People with pacemakers should consult

their physician(s) before use.
Electromagnetic fields in close
proximity to heart pacemaker could
cause pacemaker interference
or pacemaker failure.

Page 2 For technical questions, please call 1-888-866-5797. Item 94668

12. Do not operate the Worklight in

explosive atmospheres, such as in the
presence of flammable liquids, gases,
or dust. Electrical products create sparks

which may ignite the dust or fumes.

13. Do not submerge in water

or any other liquid.

14. WARNING: The cord of this product
contains lead and/or di (2-ethylhexyl)
phthalate (DEHP), chemicals known
to the State of California to cause
cancer, and birth defects or other
reproductive harm. Wash hands
after handling. (California Health &
Safety Code § 25249.5, et seq.)

Assembly

15. Warning: The warnings, cautions, and
instructions discussed in this instruction
manual cannot cover all possible
conditions and situations that may occur.
It must be understood by the operator that
common sense and caution are factors
which cannot be built into this product,
but must be supplied by the operator.

1. Charge the Worklight before
using it for the first time.

2. Plug the AC/DC Adapter into the
Worklight at its base. Plug the AC/DC
Adapter to a 120V electrical outlet.

Adapter

Connection

3. Allow the Worklight to charge. Charging
Indicator Light is the bottom LED bulb
in center row. When Unit is charging,
Charging Indicator Light will glow
red. When Charging Indicator Light
glows green, unit is fully charged.
Disconnect the AC/DC Adapter.

4. The Worklight also has a cigarette lighter
adapter which can be plugged into a
vehicle’s cigarette lighter. Allow Batteries
to charge. Disconnect the Adapter.

5. To turn the Worklight on, press down
on the On/Off Switch. To turn the
Flashlight “OFF”, press down on the
opposite end of the On/Off Switch.

On/Off
Switch

6. The Cigarette Adapter contains one
250V, fast acting 3 Amp Fuse. To replace
the Fuse, make certain the Adapter
is unplugged. Open up the Cigarette
Adapter, remove Fuse and insert
new one. Close Cigarette Adapter.

7. The Worklight can be attached to metal
work surfaces by placing its magnetic
base against the metal portion of the
work surface. The Worklight can also be
hung by the Hanging Hook at its top. The
Hanging Hook swivels 360 degrees.

Page 3For technical questions, please call 1-888-866-5797.Item 94668

Parts List

Part Description Qty.

1 AC/DC Adapter 1
2 Cigarette Adapter 1
3 Led Light 1
4 Fuse 250 V, Fast Acting 3 Amp 1
5 “S” Hanging Hook 2

Record Serial Number Here:

Note: If product has no serial number,

record month and year of purchase instead.

Note: Some parts are listed for illustration
purposes only, and are not available
individually as replacement parts.

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST IN THIS DOCUMENT
AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY
REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO
MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS
OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES
THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Limited 90 Day Warranty

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.

This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797