Harbor Freight Tools 94519 User Manual
12V Solar Exhaust Fan
®
94519
ASSEMBLY AND OPERATING INSTRUCTIONS
Due to continuing improvements, actual product may differ slightly from the product described herein.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
Copyright© 2006 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
Specifications
Construction
Exhaust Fan
LED Indicator
Dimensions 12-½” W x 36-½” L x 1” D each panel Weight 28.5 lb. Panel Only: 9.3 lb.
2 Solar Panels with Mounting Bracket,
Controller and Exhaust Fan.
6-¾” Dia. x 2” Thick
3350 RPM. 251 CFM
Red indicates “Charging”, Green indicates
“Operating”
Output 12 VDC 12 Watts 800 - 1000 mA
Voltage
Regulator
Fuse 3 Amp push in fuse
Over discharge protection less than 10.5 V
Over charge protection over 14.5 V
Save This Manual
You will need the manual for the safety warnings and precautions, assembly
instructions, operating and maintenance procedures, parts list and diagram. Keep
your invoice with this manual. Write the invoice number on the inside of the front
cover. Keep the manual and invoice in a safe and dry place for future reference.
Safety Warnings and Precautions
WARNING: When using tool, basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment.
Read all instructions before using this tool!
1. Keep work area clean. Cluttered areas invite injuries.
2. Observe work area conditions. Do not use machines or power tools in
damp or wet locations. Don’t expose Control Unit to rain. Keep work area
well lit. Do not use electrically powered tools in the presence of flammable
gases or liquids.
3. Keep children away. Children must never be allowed in the work area. Do
not let them handle machines, tools, or extension cords.
4. Store idle equipment. When not in use, tools must be stored in a dry
location to inhibit rust. Always lock up tools and keep out of reach of
children.
5. Use the right tool for the job. Do not attempt to force a small tool or
attachment to do the work of a larger industrial tool. There are certain
applications for which this tool was designed. It will do the job better
and more safely at the rate for which it was intended. Do not modify this
tool and do not use this tool for a purpose for which it was not intended.
6. Dress properly. Do not wear loose clothing or jewelry as they can be
caught in moving parts. Protective, electrically non-conductive clothes and
non-skid footwear are recommended when working. Wear restrictive hair
covering to contain long hair.
SKU 94519 For technical questions please call 1-800-444-3353 Page 2
7. Do not overreach. Keep proper footing and balance at all times. Do not
reach over or across running machines.
8. Maintain tools with care. Keep tools maintained and clean for better and
safer performance. Inspect tool cords periodically and, if damaged, have
them repaired by an authorized technician.
9. Disconnect power. Disconnect optional battery (not included) when fan is
disconnected or turned off.
10. Avoid unintentional starting. Be sure the switch is in the Off position when
not in use. This system will start and operate automatically whenever the
control unit is set at or below the current temperature and the solar panels
are connected. Disconnect the solar panels from the control unit before
doing any maintenance to the blower.
11. Stay alert. Watch what you are doing, use common sense. Do not operate
any tool when you are tired.
12. Check for damaged parts. Before using any tool, any part that appears
damaged should be carefully checked to determine that it will operate
properly and perform its intended function. Check for any broken parts or
mounting fixtures; and any other condition that may affect proper operation.
Any part that is damaged should be properly repaired or replaced by a
qualified technician. Do not use the tool if any switch does not turn On and
Off properly.
13. Guard against electric shock. Prevent body contact with grounded
surfaces such as pipes, radiators, ranges, and refrigerator enclosures.
14. Replacement parts and accessories. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty. Only use
accessories intended for use with this tool. Approved accessories are
available from Harbor Freight Tools.
15. Do not operate tool if under the influence of alcohol or drugs. Read
warning labels on prescriptions to determine if your judgment or reflexes are
impaired while taking drugs. If there is any doubt, do not operate the tool.
16. People with pacemakers should consult their physician(s) before using
this product. Electromagnetic fields in close proximity to a heart pacemaker
could cause interference to or failure of the pacemaker..
17. Maintenance. For your safety, service and maintenance should be
performed regularly by a qualified technician.
SKU 94519 For technical questions please call 1-800-444-3353 Page 3
Loading...