Harbor Freight Tools 94130 Product manual

®

CIRCUIT TESTER

3-PIECE SET

94130

ASSEMBLY & OPERATING INSTRUCTIONS

Due to continuing improvement, actual product may differ slightly from product described herein.

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our Web Site at www.harborfreight.com

Copyright© 2006 by Harbor Freight Tools®. All rights reserved. No portion of this manual or
any artwork contained herein may be reproduced in any shape or form without the
express written consent of Harbor Freight Tools.

For technical questions and replacement parts please call 1-800-444-3353.

THANK YOU for choosing a HARBOR FREIGHT TOOLS product. For future reference, please

complete the owner’s record below:

Model

______________ Serial No.____________ Purchase Date_______________

SAVE THE RECEIPT, WARRANTY AND THESE INSTRUCTIONS. It is important that you read the
entire manual to become familiar with the unit BEFORE you begin assembly.

Technical Specifications

Material: Various thermoplastics, tapered steel probes, 18 gauge stranded

copper wire, zinc-plated alligator clip
Dimensions: Each Tester is 8” in lenght
Probe Type: Needle Point with plastic cap, 1.75” L
Voltage Range: 6/12/18/24/36 D/C
Lead Wire: 48” Long, included with each tester
Battery: Tester “A” requires one “AA”, 1.5V battery (not included).
Bulb: Bulb A: 1.2V, 2W; Bulb B: 36V, 3W; Bulb C: 12V, 3W

Safety Warnings and Precautions

WARNING: When using product, basic safety precautions should always be followed to
reduce the risk of personal injury and damage to equipment.

Read all instructions before using this product!

1. Keep work area clean. Cluttered areas invite injuries.

2. Check for damaged parts. Before using any product, any part that appears damaged should
be carefully checked to determine that it will operate properly and perform its intended function.
Check for any broken or damaged parts and any other conditions that may affect its operation.
Replace or repair damaged or worn parts immediately.

3. Replacement parts and accessories. When servicing, use only identical replacement parts.
Use of any other parts will void the warranty.

4. Always check hardware and assembled parts after assembling. All connections should be
tight and hardware tightened.

5. Keep children away. Children must never be allowed in the work area. Do not let them
handle the Circuit Testers.

6. Dress properly. Wear restrictive hair covering to contain long hair.

7. Use eye protection. Always wear ANSI approved impact safety goggles when using this
product.

8. Maintain product with care. Store the Circuit Testers in a dry location.

9. There are certain applications for which these Circuit Testers were designed. Do not

modify these Circuit Testers and do not use them for a purpose for which they were not
intended.

SKU 94130 For technical questions please call 1-800-444-3353. Page 2

10. Do not use the Circuit Testers if under the influence of alcohol or drugs. Read warning
labels on prescriptions to determine if your judgement or reflexes are impaired while taking
drugs. If there is any doubt, do not use the Circuit Testers.

11. Maintain labels and nameplates on the Circuit Testers. These carry important information.

If the labels are unreadable or missing, contact Harbor Freight Tools for replacement.

12. The Circuit Testers should be kept away from children.

WARNING! Risk of explosive gases:

13. Working in the vicinity of lead-acid batteries is dangerous. Batteries generate

explosive gases during normal battery operation. For this reason, it is of utmost
importance that each time before using these Circuit Testers you read and understand
all safety warnings and precautions as outlined in this manual and those manuals
published by the battery and vehicle manufacturers and manufacturers of any
equipment you intend to use in the vicinity of the battery.

14. Make sure someone is within range of your voice and close enough to come to

your aid when you work near a lead-acid battery.

15. Keep plenty of fresh water and soap nearby in case battery acid contacts skin,

clothing, or eyes. Avoid touching eyes while working near a lead-acid battery. If battery

acid contacts skin or clothing, wash immediately with soap and water. If acid enters the
eyes, immediately flood eyes with running cold water for at least 10 minutes and get medical
attention immediately.

16. NEVER smoke or allow a spark or flame in the vicinity of a lead-acid battery or vehicle

engine.

17. Use caution to reduce the risk of dropping a metal tool onto a lead-acid battery. The

tool may spark or short circuit the battery or other electrical part that may cause an
explosion.

18. Remove personal metal items such as rings, bracelets, necklaces, and watches when

working with a lead-acid battery. A lead-acid battery can produce a short circuit current
high enough to weld a ring or other metal item, causing a severe burn.

WARNING! Operate a combustion engine only in well-ventilated areas. A running

engine produces carbon monoxide. Carbon monoxide gas is colorless,
odorless, toxic gas that can cause serious injury or death.

WARNING: The warnings, cautions, and instructions discussed in this instruction manual cannot

cover all possible conditions and situations that may occur. It must be understood by
the operator that common sense and caution are factors which cannot be built into
this product, but must be supplied by the operator.

SKU 94130 For technical questions please call 1-800-444-3353. Page 3