8’ x 10’ GREENHOUSE
®
WITH TWO VENTS
93920
ASSEMBLY INSTRUCTIONS
Due to continuing improvements, actual product may differ slightly from the product described herein.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
TO PREVENT SERIOUS INJURY, READ AND UNDERSTAND
ALL WARNINGS AND INSTRUCTIONS BEFORE USE.
Copyright© 2006 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
Contents
UNPACKING ..............................................................................2
SPECIFICATIONS ......................................................................3
Save This Manual ............................................................................... 3
GENERAL SAFETY WARNINGS AND PRECAUTIONS ..........3
BASE ASSEMBLY .....................................................................5
FRAME ASSEMBLY ..................................................................6
Assembling the Outer Frame ............................................................ 6
Assembling the Roof Frame ............................................................. 8
Assembling the Studs and Braces ................................................... 9
Assembling the Roof Studs and Braces ......................................... 12
Assembling the Window ................................................................... 13
Assembling the Doors ...................................................................... 13
Installing the Transparent Panels .................................................... 15
Panel Installation Diagram ............................................................... 16
INSPECTION, MAINTENANCE, AND CLEANING ...................17
PARTS LIST ..............................................................................18
UNPACKING
When unpacking, check to make sure all the parts shown on the Parts Lists at the
end of this manual are included. If any parts are missing or broken, please call Harbor
Freight Tools at the number shown on the cover of this manual as soon as possible.
For technical questions, please call 1-800-444-3353.
Page 2SKU 93920
SPECIFICATIONS
Overall Dimensions 120” L x 961/2” W x 865/8” H
Window Dimensions 227/8” L x 20” W
Door Dimensions 64” H x 24” W x 11/4” Thick
Materials
Aluminum Thickness 0.038”
Polycarbonate Sheet Thickness 0.165”
Weight 154 lb.
Aluminum Frame
Transparent Polycarbonate Sheets
Save This Manual
You will need this manual for the safety warnings and precautions, assembly, inspection, maintenance and cleaning procedures, parts list and assembly diagram. Keep your
invoice with this manual. Write the invoice number on the inside of the front cover. Keep
this manual and invoice in a safe and dry place for future reference.
GENERAL SAFETY WARNINGS AND PRECAUTIONS
1.
2.
3.
4.
5.
6.
KEEP WORK AREA CLEAN AND DRY. Cluttered, damp, or wet work areas invite
injuries.
KEEP CHILDREN AWAY FROM GREENHOUSE. Do not allow children to play in
or climb on this product. Although this greenhouse does include some protective
covers, there are still some exposed sharp edges. In addition, protective covers
may fall off in time. Children must be supervised if allowed near the greenhouse.
DO NOT ASSEMBLE THIS PRODUCT IF UNDER THE INFLUENCE OF ALCOHOL
OR DRUGS. Read warning labels on prescriptions to determine if your judgement
or reflexes are impaired while taking drugs. If there is any doubt, do not attempt to
assemble this product.
USE EYE PROTECTION. Wear ANSI-approved safety impact eye goggles when
assembling this product. ANSI-approved safety impact eye goggles are available
from Harbor Freight Tools.
DO NOT OVERREACH. Keep proper footing and balance at all times to prevent
tripping, falling, back injury, etcetera.
STAY ALERT. Watch what you are doing at all times. Use common sense. Do
not attempt to assemble this product when you are tired or distracted from the job
at hand.
For technical questions, please call 1-800-444-3353.
Page 3SKU 93920
7.
CHECK FOR DAMAGED PARTS. Before using this product, carefully check that
it will operate properly and perform its intended function. Check for damaged parts
and any other conditions that may affect the operation of this product. Replace or
repair damaged or worn parts immediately.
8.
9.
10.
11.
12.
13.
REPLACEMENT PARTS AND ACCESSORIES: When servicing, use only identical
replacement parts. Only use accessories intended for use with this product. Ap-
proved accessories are available from Harbor Freight Tools.
MAINTAIN THIS PRODUCT WITH CARE. Keep this product clean and dry for
better performance.
MAINTENANCE: For your safety, service and maintenance should be performed
regularly by a qualified technician.
USE THE RIGHT PRODUCT FOR THE JOB. Do not attempt to force a small
product to do the work of a larger industrial product. There are certain applications
for which this product was designed. It will do the job better and more safely in the
manner for which it was intended. Do not modify this product, and do not use this
product for a purpose for which it was not intended.
MAINTAIN A SAFE WORKING ENVIRONMENT. Keep the work area well lit. Make
sure there is adequate surrounding workspace. Avoid high traffic areas. Always
keep the work area free of obstructions, grease, oil, trash, and other debris.
PROPER GREENHOUSE LOCATION: Make sure the Greenhouse is located on
a flat, level, surface.
14.
15.
16.
17.
WARNING: This product contains or produces a chemical known to the State of
California to cause cancer and birth defects (or other reproductive harm).
(California Health & Safety Code § 25249.5, et seq.)
THIS UNIT CONTAINS PIECES WITH SHARP EDGES. The machined edges of
the aluminum parts and the ends of the panel clips may be sharp. Handle all parts
carefully.
SNOW/DEBRIS ACCUMULATION HAZARD. The heavy weight of accumulated
snow or other debris can cause parts of this greenhouse to buckle suddenly. Do
not allow debris to accumulate on top of the greenhouse. If snowfall is expected,
place additional supports (not provided) underneath the Crown (15a, 15b). NEVER
enter a greenhouse with accumulated debris on top.
WARNING: The warnings, precautions, and instructions discussed in this manual
cannot cover all possible conditions and situations that may occur. The operator
must understand that common sense and caution are factors, which cannot be built
into this product, but must be supplied by the operator.
For technical questions, please call 1-800-444-3353.
Page 4SKU 93920
BASE ASSEMBLY
IMPORTANT–READ THE FOLLOWING CAREFULLY BEFORE PROCEEDING
The first step in assembly is to assemble a proper base. The greenhouse must
•
be properly supported to help prevent property damage and injury in the event of
strong winds or inclement weather. Wind and ground conditions may vary from
site to site, and may affect the practicality and effectiveness of anchoring methods
substantially.
Be certain to check with local authorities to obtain all required building permits
•
and to familiarize yourself with any building codes that may apply.
Decide on a location for the greenhouse. The location should be a level, well-lit
•
area that is sheltered from the wind. The door of the greenhouse should not open
towards the prevailing wind, if possible.
1.
2.
Excavate an area for the base of the greenhouse. The area must be 8’ 2” wide by
10’ 2” long by 21/2” – 23/4” deep. The floor of the hole must be level and square.
The diagonal dimensions, from corner to corner, should each be 13’.
Assemble the Base outside the hole as shown below. Note that the angled edges of
the Base Plates (40, 41a, 41b) need to face the corners of the base. Use Base Bolts
(45), Base Nuts (46), and Connectors (42, 43) to secure the pieces together.
42
41a
43
41b
42
40
41a
42
40
42
43
3.
4.
5.
41b
Base Assembly
With assistance, lower the Base into the hole. The diagonal dimensions, from outside corner to outside corner, must be equal for the base to be square.
Fill the hole around the outside of the base with soil.
This base will need to be filled with about 17-18 cubic feet of gravel or another appropriate fill material (not provided). The gravel should reach up to about 1/2” – 3/4”
below the lip of the base.
For technical questions, please call 1-800-444-3353.
Page 5SKU 93920
FRAME ASSEMBLY
Front Floor
Plate (17)
ground
outside
greenhouse
Base
(40)
Gravel
Rear/Side Floor
Plates (16,18a, 18b)
ground
outside
greenhouse
Base
(40, 41a, 41b)
Gravel
44
1 2
59
44
61
Unless noted otherwise, all frame parts will be attached using the Short
•
Bolts (59) and Nuts (61) provided. Bolts should all be assembled with their
heads facing the outside of the greenhouse. Tighten Nuts only about 1/4
turn past finger-tight; be careful not to overtighten.
Lay out all parts by number prior to assembly.
•
An assistant or an appropriate support (not included) will be useful to keep
•
the partially assembled parts upright during assembly. Two assistants should
be used to assemble the Crown pieces to the rest of the frame.
Assemble on a clear, calm day. Wind may damage the Greenhouse and will
•
make assembly difficult.
1.
Use the bracket built into Side Floor Plate A (18a) to attach Side Floor Plate B (18b).
Repeat for the second pair of Side Floor Plates. Lay all Floor Plates (16-18b) out
on top of the base with the flanges facing the outside of the greenhouse as shown
above. Make sure that the Front Floor Plate (17) is on the side that you want your
door to be located.
2.
There are four Corner Studs (1) to be attached to the Floor Plates (16-18b), the end
with two holes should be at the bottom. Attach one Corner Stud (1) on the outside
of each corner using two Bolts. As shown above: 1) slide a Hold Down Connector
Cross Section
Assembling the Outer Frame
For technical questions, please call 1-800-444-3353.
Page 6SKU 93920
(44) up under the rail and over the end of the Bolt (59), then 2) secure it using a Nut
1
20a
26
(61). Use two Hold Down Connectors for each Corner Stud.
3.
Remove the Nuts (61) you used in step 1 to assemble the Side Floor Plates (18a,
18b), install a Hold Down Connector (44) over the end of each Bolt (59), and reinstall all Nuts (61).
4.
Place three Short Bolts (59) and Nuts (61) into the holes on the Top Doorway Beam
(14). Do not tighten them yet. While making sure that the profiles of the parts are
oriented as shown to the right, slide the slot on the Door Rail (28)
over the heads of the three bolts on the Top Doorway Beam.
Center the Door Rail on the Doorway Beam then tighten the
Nuts.
5.
The 14 spots requiring a Holddown Connector (44) are
marked with a plus
(+).
Attach a Corner End Cap (68) to the top outer corner of each Corner Stud (1).
26
20b
1
+
+
18b
(Rear)
23
26
16
1
++
20a
20a
18a
26
(Right)
+
+
+
20b
18b
14
26
+
+
281428
1
6.
7.
+
+
+
1
++
20a
(Left)
18a
Figure A
Assemble both Side Ceiling Plates (20a, 20b) to one another.
Attach a Side Ceiling Plate Ass’y (20) flat against the inside
of two Corner Studs (1). Make sure that the gutter on the
Side Ceiling Plate is oriented correctly, see Figure A inset.
For technical questions, please call 1-800-444-3353.
17
(Front)
Page 7SKU 93920
At this point, the completed section of the frame will likely need support. Attach the
15
3
2
15
3
2
second Ceiling Plate the same way.
8.
9.
Attach a Corner Bracket (26) at the top of each Corner Stud (1) so that the bracket
faces upwards, see diagram to the right. Leave the bottom holes of the two rear
Corner Brackets (26) empty to allow the rear brace to be attached to those holes
in the next step.
Attach the Rear Brace (23) to the inside of the two Corner Brackets (1) that are over
the Rear Floor Plate (16). Attach each end to the lower hole on the Corner Bracket
(26) using a Long Bolt (60) and Nut (61). (See Figure A.)
Assembling the Roof Frame
5
4
15a
15b
2
3
13
28
1.
2.
3.
4.
39
14
Figure B
At the side of the Greenhouse: Assemble the Front Crown (15a) to the Rear Crown
(15b) using the attached bracket.
Attach the Front-Right and Front-Left Crown Beams (2,
3) to the outside of the Crown Ass’y (15) with the angled
edges towards the top. See diagram to the right, viewed
from under the Crown, facing forward.
Attach the Top Doorway Beam (14) and Door Rail (28)
assembly to the outside (opposite the Crown) of the FrontRight and Front-Left Crown Beams (2, 3).
Attach the Front-Center Top Stud (13) to the center of the Top Doorway Beam (14).
For technical questions, please call 1-800-444-3353.
Page 8SKU 93920
5.
6.
Attach the Front-Center Top Stud (13) to the Front Crown Beams (2,3) using the
Top-center Connector (39) as shown below right.
2 3
2 3
Attach the Rear Crown Beams (4,5) to the Crown
(15b) in the same fashion as the Front Crown Beams
in step 2.
7.
Attach a Corner End Cap (68) onto the outer end of
each Crown Beam (2-5). Cover the gaps between
the Crown Beams (between 2-3 & 4-5) with a Peak
Cap (72) in each. You may desire to use some silicone (not included) to secure
the Peak Caps (72) in place.
8.
With two assistants, lift the Crown Assembly and place the Crown Beams (2-5) on
top of the Corner Brackets (26). (See Figure B.) Secure each corner in place with
the Crown Beams on the outside of the Corner Brackets.
Assembling the Studs and Braces
The 13 spots requiring a
Hold-down Connector
(44) are marked with
a plus (+).
39
9
10
8
+
TOP
+
12*
22
+
Note:
All Side Studs
(12) with no asterisk
are assembled using a
Long Bolt (60) for the bottom
connection.
All Side Studs (12) marked with an
asterisk (*) are assembled with one Long Bolt
(60) in the middle of the slot.
+
12
12
+
22
+
19
TOP
12*
+
Figure C
12*
+
22
21
24
12
+
6
+
12
+
12*
22
3913
3913
19
56
2
63
21
19
21
+
24
7
+
1.
Attach the Rear-Left, Rear-Right, and Rear-Center Studs (8, 9, & 10) to the outside
of the Rear Floor Plate (16) and Rear Brace (23). Slide a Hold-Down Connector
For technical questions, please call 1-800-444-3353.
Page 9SKU 93920
(44) under the base and over the Bolt at each Floor Plate (16) connection. Use
to
Corner
Stud (1)
Left
Doorway
Stud (6)
Front Floor Plate (17)
to
Corner
Stud (1)
Right
Doorway
Stud (7)
Long Bolts (60) for the Rear Brace (23) connections.
2.
3.
4.
5.
Attach the tops of the Rear Studs (8, 9, & 10) to the Rear-Right and Rear-Left Crown
4 5
Beams (4, 5). For the Rear-Center Stud (10), use a
4 5
Top Center Connector (39) to connect to the Crown
Beams, as shown to the right.
Refer to the Note in Figure C. Attach the two Side
Studs (12) in the center of each side (without asterisks
in Figure C) to the outside of the frame. Make the
3910
3910
bottom connections using a Long Bolt (60) for later
assembly of the Side Diagonal Brace (22). Slide a
Hold-Down Connector (44) under the base and over the Long Bolt at each bottom
connection, but do not install a Nut (61) over the Long Bolt yet.
Refer to the Note in Figure C. Attach the two Side Studs (12) near the corner of
each side (with asterisks (*) in Figure C) to the outside of the frame. Slide a Long
Bolt (60) into each slot for later Side Diagonal Brace (22) assembly. Slide a HoldDown Connector (44) under the base and over the Bolt before installing the Nut
(61) at each bottom connection.
Attach a Side Diagonal Brace (22) to the lower hole of a Corner Stud (1) on the
inside with the TOP arrow pointing towards the Corner Stud as shown in Figure
C. Use a Long Bolt (60) to attach the Brace. Attach the other three Side Diagonal
Braces (22) to the other Corner Studs (1) in the same manner.
6.
7.
8.
Attach the center hole of each Brace to the Long Bolt (60) in the center of the Side
Studs (12) designated with an asterisk (*) in Figure C. This Bolt (60) was included
in step 4, above.
Attach the bottoms of all four Side Diagonal Braces (22) to the Long Bolts (60)
installed at the bottoms of the remaining Side Studs.
View from above
Install the Left and Right Doorway Studs (6 & 7) to the outside of the frame so that
they rest flat against the frame. Their orientation should be the same as shown
above. Slide a Long Bolt (60) into each slot for later Front Brace (21) assembly.
Make the bottom connections using a Long Bolt (60) for later assembly of the Front
Diagonal Braces (24). Slide a Hold-Down Connector (44) under the base and over
For technical questions, please call 1-800-444-3353.
Page 10SKU 93920
the Long Bolt at each bottom connection, but do not install a Nut (61) over the Long
Bolt yet.
9.
10.
11.
12.
Remove the bottom Bolt from the Corner Brackets (26) at the front of the greenhouse. Install the Front Diagonal Braces (24) to the bottom hole of the Brackets on
the inside using Long Bolts (60). Attach the bottom of the Front Diagonal Braces
(24) to the Long Bolt left exposed on the Floor Plate (17) from the last step.
(See Figure C.)
Remove the second Bolt from the bottom of the front Corner Brackets (26). Connect the Front Braces (21) to the exposed hole using Long Bolts (60). Connect the
loose ends of the Front Braces (21) to the Doorway Studs (6, 7) using Long Bolts
(60). (See Figure C.)
Attach the Door Slide Support (19) to the Front-Right Crown Beam (2) using the
Long Door Support Bolt (56) and Nut (61), with the Door
19
19
Support Spacer (63) between the Support and the Stud. (See
56
Figure C, inset, and diagram to the right.) Repeat for the
other Door Slide Support (19) on the opposite side.
The frame should now rest square. Measure diagonally
from corner to corner at the top. If the measurements are
not equal, adjust the frame as needed until square. Some
63
63
2
2
21
21
56
Nuts (61) may need to be temporarily loosened to adjust the
frame properly.
13.
Place the Gutter End Caps (69) onto the ends of the Side Ceiling Plates (20a, 20b)
oriented with a gap in the bottom to allow water to drain out of the gutters.
For technical questions, please call 1-800-444-3353.
Page 11SKU 93920
Assembling the Roof Studs and Braces
36
25
11*
Note:
All Roof Studs
(11) marked with
an asterisk (*) are
assembled with one Short
Bolt (59) in the slot above the
Long Bolt(s) (60).
All Roof Studs (11) marked with a caret
(^) are assembled with two Long Bolts (60)
in the slot.
All Roof Studs (11) not marked with a caret are
assembled with only one Long Bolt (60) in the Slot.
11*^
36
25
11*
11*^
11^
11
25
25
11^
11
Figure D
1.
2.
3.
4.
5.
Attach all Roof Studs (11) to the outside of the Front/Rear Crown (15a, 15b). Leave
the bottom ends of the Roof Studs unattached for now.
Slide one Short Bolt (59) into all the Roof Studs (11) marked with an asterisk (*)
above. Slide two Long Bolts (60) into the Roof Studs indicated with a caret (^)
above. Slide one Long Bolt (60) into all the Roof Studs not marked with a caret
above. Secure the ends of all Roof Studs (11) to the outer top edge of the Side
Ceiling Plates (20a, 20b) using Short Bolts (59).
Attach Roof Braces (25) to the underside of the Roof Studs (11) side-by-side, using
the Long Bolts (60) included in the last step. Secure the ends of the Braces first,
then secure the centers.
Slide a Window Support Beam (36) onto two Roof Studs (11) marked with an asterisk (*), with the predrilled holes on the underside and the flat side facing the Crown
(15a, 15b). Use the extra Bolts (59) to secure the Beam loosely in place. Repeat
for the other Window Support Beam (36).
At this time, verify that the Door Rail (28) is oriented correctly, with the rounded
edge facing up – see number 4 on page 7.
For technical questions, please call 1-800-444-3353.
Page 12SKU 93920
Assembling the Window
1.
2.
3.
4.
5.
6.
Attach the Side Window Frames (34) to the Top Window Frame (33), as shown
below to the right.
Insert Short Bolts (59) into the holes at the bottom of the Side
Window Frames (34), so that the threads stick out the bottom of
34
333433
the window.
Remove the protective film from both sides of the Window Pane
(51). Slide the Window Pane (51) into the three-sided frame.
Slide the Bottom Window Frame (35) onto the two Short Bolts (59) and the Window
Pane (51). Secure it in place with Nuts (61). You may need to apply some pressure
to the heads of the Bolts through the Window Pane to allow the Nuts to thread on
properly.
Attach the Window Brace (38) to the Bottom Window Frame (35) using two Window
Screws (58). The holes on the Window Brace (38) should face away from the window.
Slide the top edge of the Top Window Frame (33) into the slot at
the top of the Crown (15b), see illustration to the right. The window should be aligned with the Window Brace (38) underneath
33
33
15a/
15a/
15b
15b
it. Slide the window into place over the Window Support Beam
(36). Gradually lower it into place.
7.
Using two Window Screws (58), attach the Window Stop (37) to
the Window Support Beam (36) with its tab pointing towards the Crown (*10, 11). It
should be on the underside of the Window Support Beam, inside the greenhouse.
8.
Loosen the Nuts (61) holding the Window Support Beam (36) in place and slide the
Window Support Beam (36) up to touch the window. Secure it in place.
9.
Repeat steps 1-8 for the other window.
Assembling the Doors
The doors are assembled using the Door Screws (57). The Screws thread
directly into the rounded portions of the parts in the center of the doors.
1.
2.
Place an Outer Door Frame (27a) with the slotted side down.
Attach two Center Door Frames (31) to the Outer Door Frame
(27a). Assemble them with the rounded portion facing the front,
as shown to the right.
Attach an Inner Door Frame (27b) to the other side of the Center
Door Frames (31) in the same way.
27a3127a
31
For technical questions, please call 1-800-444-3353.
Page 13SKU 93920
3.
17
Side view
64
27a
17
Side view
64
27a
Orient the assembled door frames for so that the Outer Door Frame (27a) is on the
left, and the Inner Door Frame (27b) is on the right. This is the assembly used for
the left door, the right door will be assembled later with the Outer and Inner Door
Frames on the opposite sides (outer on right, inner on left). All illustrations show
the left door assembly.
4.
5.
6.
7.
Attach the Top Door Frame (30) to the top of the Outer/Inner Door
Frames (27a, 27b). Make sure that the rounded portion faces
the front and that the flange where the pane will sit faces down
towards the center of the door, see the diagram to the right.
Using two Short Bolts (59) and two Nuts (61), attach the Door
Slider (29) to the Top Door Frame (30) with the rollers on the top
of the door.
Insert a Door Bottom Slider (64) into each end of the Bottom Door
Frame (32). Make sure that the Sliders are assembled the correct
way, with the gap facing the back of the door – see diagram to
the right. Attach the Bottom Door Frame (32) to the Outer/Inner
Door Frames (27a, 27b) using two Screws (57) on each side – the
one on the top into the Bottom Door Frame (32) and the bottom
one into the Door Bottom Slider (64).
Raise the assembled Door up and insert the first roller of its Door
Slider (29) onto the Door Rail (28). Carefully align the first Bottom
Door Slider (64) over the edge of the Front Floor Plate (17) – see
illustration to the right. Carefully slide the door over and align the
other top Roller and bottom Slider as you did the first ones.
57
57
27a
27a
27b
27b
30
30
PANE
PANE
64
64
32
32
8.
9.
Assemble and install the right door by following the preceding
steps, except place the Outer and Inner Door Frames (27a, 27b) on the opposite
sides as explained in step 3.
Once both doors are installed, install a Short Bolt (59) and Nut (61) into the hole
on the ends the Door Rail (28) to prevent the doors from sliding off the rails. Attach
the Right and Left Rail End Caps (70,71) onto the ends of the Door Rails.
For technical questions, please call 1-800-444-3353.
Page 14SKU 93920
Installing the Transparent Panels
A
Transparent
Panel
Frame
Member
Panel
Clip (67)
B C
1.
2.
3.
4.
Panel Clips (67) are used to secure the Transparent Panels in place on the Greenhouse.
Remove the protective film from both sides of all panels.
48/50
48 48
20a/20b
15a/15b
35
50
36
The Roof Panels (48) and the Roof Window Panel (50) will need to be placed as
shown in the illustrations above. The top edges of these panels need to be placed
up under the edge of the Crown (15a, 15b) or the Window Support Beam (36).
One at a time, place each Transparent Panel (47 – 49, 51 – 55) in its proper location
on the Ceiling and Frame of the Greenhouse. Then, secure the Transparent Panel
in place, using the quantity and location of Panel Clips (67) as shown in the Panel
Installation Diagram, next page. Also, refer to the panel clip installation instructions
in the following step.
5.
Be careful, Panel Clip (67) ends may be sharp and may spring back!
To attach Panel Clips:
a.
b.
c.
Place the two loose ends of the Clip into the groove in the frame.
Swing the center portion of the Clip up against the panel.
Two edges of the Clip swing under the edge of the panel and the center edge
holds the panel in place.
For technical questions, please call 1-800-444-3353.
Page 15SKU 93920
Panel Installation Diagram
#
#
#
#
#
#
#
#
# = Panel Clip (67) Location
#
#
#
#
#
#
#
52
49
#
#
#
#
#
#
#
#
#
52
#
#
#
#
49
#
#
47
#
#
#
48
#
#
#
#
#
51
#
#
#
48
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
48
#
#
#
#
47
#
#
#
#
47
#
#
#
#
#
#
#
#
47
#
#
#
#
#
#
48
#
#
50
#
#
#
#
#
#
#
#
47
#
#
#
#
#
51
50
#
#
#
#
#
#
#
#
48
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
48
#
#
#
#
#
#
#
54
#
#
#
#
48
#
#
#
#
54
#
#
#
#
55
#
#
53
#
#
#
#
55
#
#
#
#
#
#
#
#
#
#
#
#
#
#
49
#
#
#
#
#
#
48
#
#
#
#
49
55
#
#
53
#
#
#
55
#
#
#
#
For technical questions, please call 1-800-444-3353.
Page 16SKU 93920
INSPECTION, MAINTENANCE, AND CLEANING
1.
2.
3.
BEFORE EACH USE, inspect the general condition of the Greenhouse. Check for
loose screws, misalignment or binding of moving parts, cracked or broken parts,
and any other condition that may affect the safe operation of the Greenhouse. If a
problem occurs with the Greenhouse, have it corrected before further use.
Do not use damaged equipment.
TO CLEAN: Wipe with a damp cloth, using a mild detergent.
Do not use cleaners that are combustible, corrosive, or not compatible with
aluminum.
WHEN STORING: Keep the Greenhouse in a box and in a clean, dry location.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN
THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE
IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO
REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR
EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN
BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES
ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT
OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
For technical questions, please call 1-800-444-3353.
Page 17SKU 93920
PARTS LIST
Lengths given are approximate and rounded to the nearest inch.
PART DESCRIPTION Q’TY
1 Corner Stud
Front-Right Crown
2
Beam
Front-Left Crown
3
Beam
Rear-Right Crown
4
Beam
Rear-Left Crown
5
Beam
Left Doorway
6
Stud
Right Doorway
7
Stud
8 Rear-Left Stud
9 Rear-Right Stud
10 Rear-Center Stud
4’
4’ 9”
4’ 9”
4’ 9”
4’ 9”
5’ 3”
5’ 3”
5’ 4”
5’ 4”
6’ 8”
4
1
1
1
1
1
1
1
1
1
PART DESCRIPTION Q’TY
Side Ceiling Plate
20a
A
Side Ceiling Plate
20b
B
21 Front Brace
Side Diagonal
22
Brace
23 Rear Brace
Front Diagonal
24
Brace
25 Roof Brace
2’ 10”
7’ 1”
1’ 11”
5’ 7”
7’ 9”
4’ 3”
5’ 10”
2
2
2
4
1
2
4
26 Corner Bracket 4
27a Outer Door Frame
27b Inner Door Frame
5’ 2”
5’ 2”
2
2
11 Roof Stud
12 Side Stud
Front-Center Top
13
Stud
Top Doorway
14
Beam
15a Front Crown
15b Rear Crown
16 Rear Floor Plate
17 Front Floor Plate
18a Side Floor Plate A
18b Side Floor Plate B
Door Slide
19
Support
4’ 8”
4’
1’ 4”
3’ 11”
5’ 2”
4’ 10”
7’ 9”
7’ 9”
4’ 10”
5’ 2”
1’ 2”
8
8
1
1
1
1
1
1
2
2
2
28 Door Rail
29 Door Slider
30 Top Door Frame
Center Door
31
Frame
Bottom Door
32
Frame
Top Window
33
Frame
Side Window
34
Frame
Bottom Window
35
Frame
Window Support
36
Beam
37 Window Stop 2
38 Window Brace 2
7’ 8”
2’
2’
2’
2’
1’ 11”
1’ 9”
1’ 11”
2’
1
2
2
4
2
2
4
2
2
For technical questions, please call 1-800-444-3353.
Page 18SKU 93920
PARTS LIST (continued)
Part lengths are approximate and rounded to the nearest inch.
PART DESCRIPTION Q’TY
Top Center
39
Connector
Front/Rear Base
40
Plate
41a Side Base Plate A
41b Side Base Plate B
Base Plate
42
Corner Connector
Base Plate Side
43
Connector
Hold-down
44
Connector
45 Base Bolt
46 Base Nut
47 Wall Panel
8’
8’
2’
1
/4” x
10mm
1
/4”
1’ 11”
x 4’
2
2
2
2
4
2
25
24
24
10
PART DESCRIPTION Q’TY
Door Top/Bottom
55
Panel
Long Door
56
Support Bolt
57 Door Screw
58 Window Screw
59 Short Bolt
60 Long Bolt
61 Nut
Door Support
63
Spacer
Door Bottom
64
Slider
2’ x 1’
11”
M6 x
33 mm
ST4.3 x
19 mm
ST4 x
7.5 mm
M6 x
10 mm
M6 x
18 mm
M6
4
2
32
8
122
40
184
2
4
65 Spanner Wrench 2
48 Roof Panel
Front/Rear Side
49
Panel
Roof Window
50
Panel
51 Window Pane
Rear Center
52
Panel
Door Center
53
Panel
54 Front Top Panel
1’ 11” x
4’ 9”
1’ 11” x
5’ 4”
1’ 11”
x 3’
1’ 11” x
1’ 9”
1’ 11” x
6’ 8”
2’ x 9”
1’ 11” x
1’ 4”
8
4
2
2
2
2
2
66 Hex Wrench 1
67 Panel Clip 206
68 Corner End Cap 8
69 Gutter End Cap 4
Right Rail End
70
Cap
1
71 Left Rail End Cap 1
72 Peak Cap 2
Note: Some parts are listed and shown for illustration purposes only and are not available
individually as replacement parts.
For technical questions, please call 1-800-444-3353.
Page 19SKU 93920
Loading...