For technical questions and replacement parts, please call 1-800-444-3353
Page 2
Specifications
Laser Dot AccuracyUp to 98 Feet
Laser Line AccuracyUp to 33 Feet
Vial Accuracy+/- .3 Degrees
Power Source“AAA” Batteries (Qty. 2), 9V Battery (Qty. 1)
Save This Manual
You will need the manual for the safety warnings and precautions, assembly instructions,
operating and maintenance procedures, parts list and diagram. Keep your invoice with this
manual. Write the invoice number on the inside of the front cover. Keep the manual and
invoice in a safe and dry place for future reference.
Safety Warnings and Precautions
WARNING: When using tool, basic safety precautions should always be followed to
reduce the risk of personal injury and damage to equipment.
Read all instructions before using this tool!
1.Keep work area clean. Cluttered areas invite injuries.
2.Observe work area conditions. Don’t expose to rain. Keep work area well lit.
3.Keep children away. Children must never be allowed in the work area. Do not let
them handle the Laser Level.
4.Store idle equipment. When not in use, tools must be stored in a dry location to
inhibit rust. Always lock up tools and keep out of reach of children.
5.Use the right tool for the job. There are certain applications for which this tool was
designed. Do not modify and do not use this tool for a purpose for which it was not
intended.
6.Never direct the laser beam into the eyes of any person or animal. THIS MAYCAUSE SEVERE INJURY TO THE EYE. Do not look into the beam during operation.
Make certain to switch the Laser Level to “OFF” when making adjustments or
changing the batteries. Laser light, when reflected off a mirror like surface can cause
serious eye damage.
7.Only use the type of battery recommended in this manual. Use only “AAA”batteries for the Laser, and a 9V battery for the digital display. Do not mix old
and new batteries.
8.Maintain tools with care. Keep tools clean for better and safer performance.
9.Stay alert. Watch what you are doing, use common sense. Do not operate any tool
when you are tired.
10.Check for damaged parts. Before using any tool, any part that appears damaged
should be carefully checked to determine that it will operate properly and perform its
intended function. Any part that is damaged should be properly repaired or replaced
by a qualified technician. Do not use the tool if any switch does not turn On and Off
properly.
11.Replacement parts and accessories. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty.
12.Do not operate tool if under the influence of alcohol or drugs. Read warning
labels if taking prescription medicine to determine if your judgment or reflexes are
impaired while taking drugs. If there is any doubt, do not operate the tool.
13.Maintenance. For your safety, service and maintenance should be performed
regularly by a qualified technician.
14.Use fresh batteries. Weak batteries could affect the accuracy of this tool.
Warning: The warnings, cautions, and instructions discussed in this instruction manual
cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be
built into this product, but must be supplied by the operator.
Unpacking
When unpacking, check to make sure that the product is intact and undamaged. If any
parts are missing or broken, please call Harbor Freight Tools at the number on the cover of
this manual as soon as possible.
Using the Horizontal and Vertical Vials (9 and 10).
The vials on the level can be read by observing the bubble within. If the bubble is
centered in between the lines, then the Vial is level.
Using the level with the Laser.
1.Before each use, press the Calibration Button (7) and hold it for a few seconds until
the display reads Zero. You may use a known level surface or another level to assist
you with Zero calibration.
Each Button on the unit functions as listed below:
On/Off Button (4) - This button turns on and off the LCD (3).
Preset Angle Button (5) - Pressing and holding down this button will lock the digital
reading in the display, making it easy to move the level to get a closer look at the
reading.
Gradient Button (6) - This button translates degree reading into a percentage from
Zero to 100 percent. When the degree is within 0 to 45, the percentage will be the
degree measured, divided by 45. When the degree is within the range between 45
and 90, then the percentage will be 90 minus the degree measured, divided by 45.
Hold/Display Button (8) - This button has two features. First, if you push the button
for one second, it allows the Level to emit an audible beep when the level is either at
zero or ninety degrees. Secondly, if you hold the button down for five seconds, it will
light up the display.
Laser On/Off Button (12)
Switch (18). If the Slide Switch (18) is in the upper position, the upper button will
project a vertical line and the lower button will project a horizontal line. When the
Slide Switch (18) is in the lower position, the upper button will not project a laser
beam, and the lower button will project a simple dot beam. See FIGURE 1 below.
Slide Switch (18)
FIGURE 1
- The operation is determined by the setting of the Slide
Part No. DescriptionPart No. DescriptionPart No. Description
1 Laser Diode7 Calibration Button13 “AAA” Battery (Qty. 2)
2 End Cap 18 Hold/Display Button14 End Cap 2
3 LCD9 Horizontal Dial15 Screw
4 On/Off Button10 Vertical Vial16 Battery Cover
5 Preset Angle Button11 Body17 9 Volt Battery
6 Gradient Button12 Laser On/Off Button18 Slide Switch
Assembly Drawing
18
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS
MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT
HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE
IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER
AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT
BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR
HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
NOTE: Some parts are listed and shown for illustration purposes only and are not available
individually as replacement parts.