Harbor Freight Tools 93682 User Manual

®

ELECTRIC STAPLER

93682

ASSEMBLY & OPERATING INSTRUCTIONS

Due to continuing improvement, actual product may differ slightly from product described herein.

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our Web Site at www.harborfreight.com

Copyright© 2005 by Harbor Freight Tools®. All rights reserved. No portion of this manual or
any artwork contained herein may be reproduced in any shape or form without the
express written consent of Harbor Freight Tools.

For technical questions and replacement parts please call 1-800-444-3353.

THANK YOU for choosing a HARBOR FREIGHT TOOLS product. For future reference, please

complete the owner’s record below:

Model

______________ Serial No.____________ Purchase Date_______________

SAVE THE RECEIPT, WARRANTY AND THESE INSTRUCTIONS. It is important that you read the
entire manual to become familiar with the unit BEFORE you begin assembly.

Technical Specifications

Motor: 120V AC, 60Hz, 1 Amp.
Material: Molded ABS housing, rubber feet, formed sheet metal staple channel
Plug: 2 prong plug polarized
Overall Dimensions: 7-1/2” L X 2-7/8” W x 4-5/8” H
Staple Length: Standard Gauge, 1/2” crown x 1/4” Long
Channel Capacity: 150 Staples
Staples up to 12 sheets at a time

Safety Warnings and Precautions
WARNING: When using product, basic safety precautions should always be followed to
reduce the risk of personal injury and damage to equipment.

Read all instructions before using this product!

WORK AREA

1. Keep your work area clean and well lit. Cluttered benches and dark areas invite

accidents.

2. Do not operate the Stapler in explosive atmospheres, such as in the presence of

flammable liquids, gases, or dust. Electrical products create sparks which may ignite the
dust or fumes.

3. Keep bystanders, children, and visitors away while operating the Stapler.

Distractions can cause you to lose control.

ELECTRICAL SAFETY

4. Grounded products must be plugged into an outlet properly installed and grounded in

accordance with all codes and ordinances. Never remove the grounding prong or
modify the plug in any way. Do not use any adapter plugs. Check with a qualified
electrician if you are in doubt as to whether the outlet is properly grounded. If a

grounded product should electrically malfunction or break down, grounding provides a low
resistance path to carry electricity away from the user.

SKU 93682 For technical questions please call 1-800-444-3353. Page 2

5. Double insulated products are equipped with a polarized plug (one blade is wider

than the other). This plug will fit in a polarized outlet only one way. If the plug does
not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician to install a polarized outlet. Do not change the plug in any way.

Double insulation
grounded power supply system.

6. Avoid body contact with grounded surfaces such as pipes, radiators, ranges, and

refrigerators. There is an increased risk of electric shock if your body is grounded.

7. Do not abuse the Power Cord. Never use the Power Cord to carry the Stapler or

pull the Plug from an outlet. Keep the Power Cord away from heat, oil, sharp edges,
or moving parts. Keep the Power Cord clear of the stapling area. Replace damaged
Power Cords immediately. Damaged Power Cords increase the risk of electric shock.

8. Do not expose the stapling equipment to rain or wet conditions. Water entering

electrically powered equipment will increase the risk of electric shock. The Stapler is
intended for indoor use only.

9. Stay alert. Watch what you are doing, and use common sense when operating the

Stapler. Do not operate the Stapler while tired or under the influence of drugs,
alcohol, or medication.

eliminates the need for the three wire grounded power cord and

PERSONAL SAFETY

10. Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your

hair and clothing away from the Stapler. Loose clothes, jewelry, or long hair can be

caught in the Stapler, causing personal injury.

11. Use safety equipment. Always wear eye protection during assembly and

maintenance.

TOOL USE AND CARE

12. Do not overload the Stapler. Use the correct Stapler for your application. The

Stapler will do the job better and safer at the speed and capacity for which it is designed.

13. Disconnect the Power Cord Plug from the power source before inserting staples,

making any adjustments, changing accessories, or storing the Stapler. Such
preventive safety measures reduce the risk of turning on the product accidentally.

14. Store idle tools out of reach of children and other untrained persons. The Stapler is

dangerous in the hands of untrained users.

15. Maintain the Electric Stapler with care. Do not use a damaged Stapler. Tag damaged

Stapler “Do not use” until repaired.

SERVICE

16. Stapler service must be performed only by qualified repair personnel.

Service or maintenance performed by unqualified personnel could result in a risk of injury.

SKU 93682 For technical questions please call 1-800-444-3353. Page 3